The AR8327 switch gets its configuration from platform
data or from the device-tree. This allows to start it
from the probe routine. Doing so makes it usable with
ethernet drivers which only connects to the PHY device
when the ethernet interface is opened.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36050
Move switch starting code into a separate function.
This makes it usable from other places.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36049
Move platform_data specific configuration code
into a separate routine. Do it in preparation
for the upcoming OF support.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36046
Fetch the PORT_STATUS values in ar8327_hw_init and
store those in a private data stucture for later use.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36045
Return with the PORT_STATUS register value instead of
writing that directly into the corresponding register.
Also rename the function to ar8327_get_port_init_status.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36043
The presence of the platform data is already verified in
ar8327_hw_init, and the driver does not start without that
anyway.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36042
Setting this bit stops BCM53125 (bgmac actually) from receiving any
packets. This bit is cleared conditionally in b53_switch_reset and it
seems the same is done in bcmrobo.c which never sets that bit again.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 35723
This contains the following new bigger changes:
* new partition parser which still could lake some features or have bugs
* new nand flash driver
* using physmap-flash flash driver for parallel flash
* some changes to the serial flash driver
With these changes OpenWrt starts using more of the mainline flash drivers.
SVN-Revision: 35632
r35336 exposed PTP, which has additional drivers on ixp4xx, causing it to
not build with PTP enabled.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 35611
Currently the switch gets registered when an ethernet
driver connects to a PHY of the switch. This method does
not work with the ethernet drivers which are connecting
to the PHY from their ndo_open callback. With those
ethernet drivers, the driver tries to register the switch
each time when the etherned device is opened and this causes
a deadlock.
Move the switch registration into the probe routine to fix
this problem.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35602
The switches are accessed via an MDIO bus. Set the alias
to the name of the MDIO bus, and show that in the message
along with the name of the switch switch device.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35560
The private data of the switch is already
allocated in ar8216_priv, assign that to
each PHY on the same MDIO bus. Also remove
the redundant code from ar8216_config_init.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35559
Sujith says:
This commit breaks the WAN port on my AP96 - DHCP fails.
Reverting it fixes the issue.
commit b67cc3a0cdd02973610d4d5a63226d1c44841e94
Author: juhosg <juhosg@3c298f89-4303-0410-b956-a3cf2f4a3e73>
Date: Fri Feb 8 09:13:18 2013 +0000
generic: ar8216: simplify phy features setup
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@355183c298f89-4303-0410-b956-a3cf2f4a3e73
This change restores the previous behaviour and moves
the code into the ar8216_probe function.
Reported-by: Sujith Manoharan <sujith@msujith.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Tested-by: Sujith Manoharan <sujith@msujith.org>
SVN-Revision: 35549
