Commit graph

586 commits

Author SHA1 Message Date
Andrey Jr. Melnikov
19c7e950af ramips: move mt7620n i2c_pins definition to right place
Move to i2c pins pinmux node to the pinctrl node.

Fixes: a0685deec4 ("ramips: Add i2c support for mt7620n")

Signed-off-by: Andrey Jr. Melnikov <temnota.am@gmail.com>
[fix commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-28 18:39:57 +02:00
Franz Flasch
8375623a06 ramips: add support for TP-Link Archer C2
Specification:

- System-On-Chip: MT7620A
- CPU/Speed: 580 MHz
- Flash-Chip: Winbond 25Q64BVSIG
- Flash size: 8192 KiB
- RAM: 64 MiB
- Wireless No1: SoC-integrated: MT7620A 2.4GHz 802.11bgn
- Wireless No2: On-board chip: MT7610EN 5GHz 802.11ac
- Switch: RTL8367RB Gigabit Switch
- USB: Yes 1 x 2.0

Preparing a TFTP recovery image for initial flashing:

Currently the only method to install openwrt for the first time is via
TFTP download in u-boot. After first install you can use regular updates.
WARNING: This method also overwrites the bootloader partition!

Create a TFTP recovery image:

1) Download a stock TP-Link Firmware file here:
     https://www.tp-link.com/en/download/Archer-C2_V1.html#Firmware
2) Extract u-boot from the binary file:
     #> dd if=c2v1_stock_firmware.bin of=c2v1_uboot.bin bs=1 skip=512 count=131072
3) Now merge the sysupgrade image and the u-boot into one binary:
     #> cat c2v1_uboot.bin openwrt-squashfs-sysupgrade.bin > ArcherC2V1_tp_recovery.bin

The resulting image can be flashed via TFTP recovery mode.

Flash instructions:

1) To flash the recovery image, start a TFTP server from IP address
   192.168.0.66 and serve the recovery image named
   ArcherC2V1_tp_recovery.bin.
2) Connect your device to the LAN port, then press the WPS/Reset button
   and power it up. Keep pressing the WPS/Reset button for 10 seconds.
   It will try to download the recovery image and flash it.

It can take up to 20-25 minutes to finish. When it reaches 100%, the
router will reboot itself.

Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
2018-06-25 20:52:18 +02:00
Franz Flasch
abb7524683 ramips: fix ZyXEL Keenetic Viva switch config
The rtl8367b driver never supported a mdio property and it is quite
likely that the switch never worked for the board.

Use the mii-bus property instead to manage the switch via a mdio bus.

Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
2018-06-25 20:52:18 +02:00
Chuanhong Guo
ed40173dfc ramips: Add support for Phicomm K2G
Specification:
- SoC: MediaTek MT7620A
- Flash: 8 MB
- RAM: 64 MB
- Ethernet: 4 FE ports and 1 GE port (RTL8211F on port 5)
- Wireless radio: MT7620 for 2.4G and MT7612E for 5G, both equipped with external PA.
- UART: 1 x UART on PCB - 57600 8N1

Flash instruction:
The U-boot is based on Ralink SDK so we can flash the firmware using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART line as described on the PCB.
4. Power up the device and press 2, follow the instruction to
   set device and tftp server IP address and input the firmware
   file name. U-boot will then load the firmware and write it into
   the flash.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-06-21 22:00:02 +02:00
Tobias Schramm
5684d08741 ramips: Add support for Mikrotik RouterBOARD RBM33g
This commit adds support for the Mikrotik RouterBOARD RBM33g.

=Hardware=

The RBM33g is a mt7621 based device featuring three gigabit ports, 2
miniPCIe slots with sim card sockets, 1 M.2 slot, 1 USB 3.0 port and a male
onboard RS-232 serial port. Additionally there are a lot of accessible
GPIO ports and additional buses like i2c, mdio, spi and uart.

==Switch==

The three Ethernet ports are all connected to the internal switch of the
mt7621 SoC:

port 0: Ethernet Port next to barrel jack with PoE printed on it
port 1: Innermost Ethernet Port on opposite side of RS-232 port
port 2: Outermost Ethernet Port on opposite side of RS-232 port
port 6: CPU

==Flash==

The device has two spi flash chips. The first flash chips is rather small
(512 kB), connected to CS0 by default and contains only the RouterBOOT
bootloader and some factory information (e.g. mac address).
The second chip has a size of 16 MB, is by default connected to CS1 and
contains the firmware image.

==PCIe==

The board features three PCIe-enabled slots. Two of them are miniPCIe
slots (PCIe0, PCIe1) and one is a M.2 (Key M) slot (PCIe2).
Each of the miniPCIe slots is connected to a dedicated mini SIM socket
on the back of the board.

Power to all three PCIe-enabled slots is controlled via GPIOs on the
mt7621 SoC:

PCIe0: GPIO9
PCIe1: GPIO10
PCIe2: GPIO11

==USB==

The board has one external USB 3.0 port at the rear. Additionally PCIe
port 0 has a permanently enabled USB interface. PCIe slot 1 shares its
USB interface with the rear USB port. Thus only either the rear USB port
or the USB interface of PCIe slot 1 can be active at the same time. The
jumper next to the rear USB port controls which one is active:

open: USB on PCIe 1 is active
closed: USB on rear USB port is active

==Power==

The board can accept both, passive PoE and external power via a 2.1 mm
barrel jack. The input voltage range is 11-32 V.

=Installation=

==Prerequisites==

A USB -> RS-232 Adapter and a null modem cable are required for
installation.

To install an OpenWRT image to the device two components must be built:

1. A openwrt initramfs image
2. A openwrt sysupgrade image

===initramfs & sysupgrade image===

Select target devices "Mikrotik RBM33G" in
openwrt menuconfig and build the images. This will create the images
"openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" and
"openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" in the output
directory.

==Installing==

**Make sure to back up your RouterOS license in case you do ever want to
go back to RouterOS using "/system license output" and back up the created
license file.**

Serial settings: 115200 8N1

The installation is a two-step process. First the
"openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" must be booted
via tftp:

1. Set up a dhcp server that points the bootfile to tftp server serving
   the "openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin"
   initramfs image
2. Connect to WAN port (left side, next to sys-LED and power indicator)
3. Connect to serial port of board
4. Power on board and enter RouterBOOT setup menu
5. Set boot device to "boot over ethernet"
6. Set boot protocol to "dhcp protocol" (can be omitted if DHCP server
   allows dynamic bootp)
6. Save config
7. Wait for board to boot via Ethernet

On the serial port you should now be presented with the OpenWRT boot log.
The next steps will install OpenWRT persistently.

1. Copy "openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" to the device
   using scp.
2. Write openwrt to flash using "sysupgrade
   openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin"

Once the flashing completes reboot the router and let it boot from flash.
It should boot straight to OpenWRT.

Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-06-21 06:54:42 +02:00
Deng Qingfang
feb0a0bf22 ramips: fix Newifi D1 mtd partition
Newifi D1 has 32 MiB flash, so the firmware partition size should be 0x1fb0000

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2018-06-21 06:54:42 +02:00
INAGAKI Hiroshi
189815462c ramips: add support for ELECOM WRC-1167GHBK2-S
ELECOM WRC-1167GHBK2-S is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7621A.

Specification:

- MT7621A (2-Cores, 4-Threads)
- 128 MB of RAM (DDR3)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz
  - MediaTek MT7615D
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 2x keys
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - baudrate: 57600 bps

Flash instruction using factory image:

1. Rename the factory image to "wrc-1167ghbk2-s_v0.00.bin"
2. Connect the computer to the LAN port of WRC-1167GHBK2-S
3. Connect power cable to WRC-1167GHBK2-S and turn on it
4. Access to "http://192.168.2.1/details.html" and open firmware
update page ("手動更新(アップデート)")
5. Select the factory image and click apply ("適用") button
6. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-06-19 20:46:21 +02:00
Maxim Anisimov
8956eb502d ramips: add support for TP-Link TL-WR842N v5
TP-Link TL-WR842N v5 are simple N300 router with 5-port FE switch and
non-detachable antennas. Its very similar to TP-Link TL-MR3420 V5.

Specification:

- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- USB 2.0 Port
- UART (J1) header on PCB (115200 8n1)
- 7x LED, 2x button, power input switch

Flash instruction:

The only way to flash OpenWrt image in wr842nv5 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "lede-ramips-mt7628-tplink_tl-wr842n-v5-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2018-06-16 10:08:51 +02:00
lbzhung
291e34edff ramips: fix mt7688 watchdog register base addr
I found mt7688 watchdog not working. The watchdog registers are identical
for mt7621 and mt7628/mt7688. The first watchdog related register is at
0x10000100, the last one - a 16bit sized - at 0x10000128.

Set the correct register address and size in the dtsi file to get the
watchdog working.

Signed-off-by: lbzhung <gewalalb@gmail.com>
[add commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-16 10:08:51 +02:00
INAGAKI Hiroshi
a32c06f44d ramips: add support for I-O DATA WN-GX300GR
I-O DATA WN-GX300GR is a 2.4 GHz band 11n router, based on MediaTek
MT7621S.

Specification:

- MT7621S (1-Core, 2-Threads)
- 64 MB of RAM
- 8 MB of Flash (SPI)
- 2T2R 2.4 GHz
- 5x 10/100/1000 Mbps Ethernet
- 2x LEDs, 4x keys (2x buttons, 1x slide switch)
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - baudrate: 115200 bps (U-Boot, OpenWrt)

Flash instruction using initramfs image:

1. Connect serial cable to UART header
2. Rename OpenWrt initramfs image for WN-GX300GR to "uImageWN-GX300GR"
and place it in the TFTP directory
3. Set the IP address of the computer to 192.168.99.8, connect to the
LAN port of WN-GX300GR, and start the TFTP server on the computer
4. Connect power cable to WN-GX300GR and turn on the router
5. Press "1" key on the serial console to interrupt boot process on
U-Boot, press Enter key 3 times and start firmware download via TFTP
6. WN-GX300GR downloads initramfs image and boot with it
7. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for WN-GX300GR
8. Wait ~150 seconds to complete flasing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-06-08 09:56:27 +02:00
Rosen Penev
289b2f5e85 ramips: mt7621: Fix some cosmetic DTC warnings
Node /cpus/cpu@0 has a unit name, but no reg property
Node /cpus/cpu@1 has a unit name, but no reg property
Node /cpuintc@0 has a unit name, but no reg property
Node /cpuclock@0 has a unit name, but no reg property
Node /sysclock@0 has a unit name, but no reg property
Node /pcie@1e140000/pcie0 missing ranges for PCI bridge (or not a bridge)
Node /pcie@1e140000/pcie0 missing bus-range for PCI bridge
Node /pcie@1e140000/pcie1 missing ranges for PCI bridge (or not a bridge)
Node /pcie@1e140000/pcie1 missing bus-range for PCI bridge
Node /pcie@1e140000/pcie2 missing ranges for PCI bridge (or not a bridge)
Node /pcie@1e140000/pcie2 missing bus-range for PCI bridge

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-06-08 09:31:37 +02:00
Kevin Darbyshire-Bryant
8110bf18f4 ramips: mir3g dts define usb port Vcc volt regulator GPIO
Define USB port power on/off GPO as voltage regulator type instead of
exposing as a normal GPIO.

The GPO is now controlled by the USB driver via the voltage regulator
definition.  The regulator is of fixed output type (5V for USB) hence the
GPO switches power on/off to USB pin 1 (Vcc)

USB port power is enabled on driver load and disabled on driver unload.

Enable kernel support for fixed voltage regulator types on mt7621.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-06-08 09:31:36 +02:00
John Crispin
64878a5616 Revert "ramips: improve interrupt mapping"
This reverts commit 5f7396ebef.

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 11:42:11 +02:00
John Crispin
1d3c286381 Revert "ramips: Fix WiFi after 5f7396ebef09b224edf08b0bda113613a42f0928"
This reverts commit 02f815d190.

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 11:41:51 +02:00
Rosen Penev
976c27f2dd ramips: Fix a few other GnuBee DTS differences
I was carrying a local commit that added the sdhci stuff and missed it
as a result.

Also fix the rgmii3 thing in the PC2 DTS file as that's bogus and causes
a dmesg warning that it's bogus.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-05-30 06:35:24 +02:00
Rosen Penev
02f815d190 ramips: Fix WiFi after 5f7396ebef
That commit exposed a bug in the DTS files used by mt7621 where the wrong
reg value for pcie1 (and potentially pcie2) was being used. This was
causing WiFi failures for interfaces in pcie1.

eg. 2.4GHz working but not 5GHz.

As all of these dts entries are already specified in mt7621.dtsi, remove
them.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-05-30 06:33:56 +02:00
Rosen Penev
8c818fa1f0 ramips: Fix up GnuBee PC1 DTS file a little
There's nothing connected to i2c on this board, so remove it.

Also edited the gpio group to match the PC2 as they're the same.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-05-24 08:57:33 +02:00
Matthias Badaire
52809db544 ramips: fix to mt7620a and add support for i2c on WD03
There was an error on initial commit, the proper soc is mt7620n (which is
more limited than mt7620a). Moreover, there is a battery management
controller connected to the i2c port of the mt7620n. I have a small piece
of i2c code to get battery level coming.

Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
2018-05-22 21:02:01 +02:00
David Bauer
35d00d9a41 ramips: fix Archer C50v3 LED mapping
This commit fixes the wrong LED mapping of the Archer C50 v3.
Commit was tested with an EU device.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-05-22 20:34:14 +02:00
YuheiOKAWA
d91953cb53 ramips: add support for YUKAI Engineering Inc. BOCCO
BOCCO is a communication robot provided by YUKAI Engineering Inc.

SoC: MT7620A
MEM: 256MB
Flash: 8MB
NAND: 512MB (non support)
Include Sound DAC and AMP.
No Wired Ethernet.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
2018-05-18 11:19:00 +02:00
Matthias Badaire
a0685deec4 ramips: Add i2c support for mt7620n
I2c is supported on mt7620n like on mt7620a when checking the datasheet

Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
2018-05-15 06:39:46 +02:00
NeilBrown
5f7396ebef ramips: improve interrupt mapping
As the Interrupts for the PCI adapters are listed in
devicetree we shouldn't need to have them explicit in the code.

The simplest way to do this is to use of_irq_parse_and_map_pci()
and specify an interrupt-map which identifies the different
PCI hosts by bus/slot numbers.
This has the advantage that the hwirq number are mapped to virq
numbers for us, so the ugly hack can go.

Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-14 16:23:59 +02:00
Davide Ammirata
004cc22e4e ramips: add support for mqmaker witi 512mb version
Splitted out the dts file and create the new dts for the 256 MByte RAM and
the 512 MB RAM version.

Migrate both versions to the common board detection.

The install the 512 MByte Version on a board running the 256 MByte image,
a forceful sysupgrade with the -F flag is required.

Signed-off-by: Davide Ammirata <list@davidea.it>
2018-05-07 18:54:23 +02:00
Matthias Badaire
5ef79af4f8 ramips: add support for Ravpower WD03
The RavPower WD03 is a battery powered SD card reader and a USB port.

Specifications:
SOC:     MediaTek MT7620N
BATTERY: 6000mah
WLAN:    802.11bgn
LAN:     1x 10/100 Mbps Ethernet
USB:     1x USB 2.0 (Type-A)
RAM:     PM Tech PMD708416CTR-5CN 32 MB
FLASH:   Holtek HT66F40 - 8 MB Flash
LED:     Power button and 4 leds to indicate power level of the
         battery (could not get control of that)
INPUT:   Power, reset button
OTHER:   USB SD-Card reader with card detect on GPIO#42

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi (Correct MAC-address)
 - installation from tftp
 - OpenWRT sysupgrade (Preserving and non-preserving)
 - LEDs
 - Buttons

Installation:
 - Download the sysupgrade image
 - Place it in the root of a clean TFTP server running on your computer.
 - Rename the image to "kernel" — be sure there is no file extension.
 - Plug the WD03 into your computer via ethernet.
 - Set your computer to use 10.10.10.254 as its IP address.
 - With your WD03 shut down, hold down the power button until the first
   white LED lights up.
 - Push and hold the reset button and release the power button. Continue
   holding the reset button for 30 seconds or until it begins searching
   for files on your TFTP server, whichever comes first.
 - The WD03 (10.10.10.128) will look for your computer at 10.10.10.254
   and install the kernel file. Once it has finished installation of the
   kernel file, it will search for a (nonexistent) rootfs file — when it
   begins searching for this file, shut down the WD03 by holding the
   power button normally.
 - Start up your WD03 normally.

Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
2018-05-07 18:54:23 +02:00
Mathias Kresin
91e11bec74 ramips: fix mt7628 eval board pinmux
There is no pinmux group "jtag" for mt7628 and the pinmux driver fails
to load due to the use of the not existing group.

Fixes: FS#1515

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-25 20:33:27 +02:00
Mathias Kresin
e988b0fe0d ramips: mt7620: fix double use of pins
The pins are used as (LED) GPIOs and can't be used at the same time as
hardware controlled ephy (LED) pins.

Fixes: FS#1500

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-17 08:40:56 +02:00
Felix Fietkau
07b4e49abb ramips: fix usb phy compatible string (should fix FS#1489)
In the new USB phy driver, it checks the compatible string before
attempting to iomap its mem resource and do the extra PHY init

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-13 13:13:53 +02:00
Vianney le Clément de Saint-Marcq
bcf2125142 ramips: add support for Zorlik ZL5900V2
The Zorlik ZL5900V2 is an unbranded clone of HAME MPR-A1/2.  It is
marketed as "3G Wi-Fi Router".  Only the PCB has the model name
"ZL5900V2" printed on it.

Specifications:
- Ralink RT5350F (360 MHz)
- 32 MB RAM
- 8 MB Flash
- 802.11bgn 1T1R
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (Type-A)
- 5200 mAh battery

The ramdisk image (not the squashfs sysupgrade image) can be flashed
through the web interface (named "GoAhead") of the factory firmware.
However, as the factory firmware does not cleanly unmount the rootfs
before flashing, the device may hang instead of rebooting after
successful write.  Power cycling the device gets you in OpenWrt where
the squashfs image may be flashed through normal sysupgrade procedure.

Signed-off-by: Vianney le Clément de Saint-Marcq <code@quartic.eu>
2018-04-08 09:53:50 +02:00
Zheng Qian
80a94aacaf ramips: add support for the YouHua WR1200JS
YouHua tech WR1200JS is an AC1200 router with 5 1Gb ports (4 Lan, 1 Wan)
and 1 USB 2.0 port.

Devices is base on MediaTek MT7621AT + MT7603E + MT7612E.

Specification:

- MT7612AT (880 MHz)
- 128 MB of RAM
- 16 MB of FLASH (SPI NOR)
- 5x 10/100/1000 Mbps Ethernet
- 2T2R 2.4 GHz (MT7603E)
- 2T2R 5 GHz (MT7612E)
- 1x USB 2.0
- 10x LED (Power 2G 5G WPS Internet LAN4-1 USB)
- 3x button (reset wifi wps)
- DC jack for main power input (12V)

Installation:

1.) Press reset key 5 sec and restore the factory default
2.) Login webUI and change username to root and set a
    new password
3.) Visit http://192.168.2.254/adm/telnetd.shtml and
    turn on the telnet service
4.) Copy openwrt-ramips-mt7621-youhua_wr1200js-initramfs-kernel.bin
    to a usb pan
5.) Plug the usb pan to the router, telnet to the router
    and login by root
6.) cd /media/sda1 and check the initramfs file is there
7.) exec command:
    mtd_write write openwrt-ramips-mt7621-youhua_wr1200js-initramfs-kernel.bin Kernel
8.) reboot and visit 192.168.1.1

Signed-off-by: Zheng Qian <sotux82@gmail.com>
2018-04-08 09:52:48 +02:00
Giuseppe Lippolis
1680ae7eae ramips: add dwr-512 jboot firmware configuration
The previous fw version require the replacement of the stock bootloader
with u-boot. This prevent an easy stock restore of the original fw.

Now a proper fw util has been developed to manage the stock jboot
bootloader. Therefore make sense have a fw image for the stock
bootloader.

The old fw configuration (u-boot) is not compatible with the new one
and will not be supported anymore.

So at the end 2 image can be generated:

1) factory image with jboot bootloader
     openwrt-ramips-rt305x-dwr-512-b-squashfs-factory.bin
2) sysupgrade image with jboot bootloader
     openwrt-ramips-rt305x-dwr-512-b-squashfs-sysupgrade.bin

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2018-04-08 09:51:06 +02:00
Vianney le Clément de Saint-Marcq
eda27d7557 ramips: fix usbphy DT nodes on linux 4.14
The Ralink USB PHY driver merged into mainline has a slightly different
device tree binding than the patch that was used with linux 4.9.
The new driver requires a `ralink,sysctl` node pointing to the `syscon`
node.

This patch also sets `#phy-cells` to 0, as recommended by the mainline
documentation [1].

[1] Documentation/devicetree/bindings/phy/ralink-usb-phy.txt

Signed-off-by: Vianney le Clément de Saint-Marcq <code@quartic.eu>
2018-04-07 17:53:34 +02:00
Piotr Dymacz
10ea53f900 ramips: add U-Boot env support for ALFA Network AC1200RM
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-04-06 23:11:00 +02:00
John Crispin
424a9ae128 ramips: implement hardware NAT offload for MT7621
Supports IPv4 flow offloading on MT7621 for Routing, SNAT and DNAT

Supported are regular ethernet->ethernet connections, including one
802.1q VLAN and/or PPPoE encapsulation

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-06 19:37:53 +02:00
Giuseppe Lippolis
6525bffc0a ramips: add support for DLINK DWR-921-C1
The DWR-921-C1 Wireless Routers with LTE embedded modem is based on the
MT7620N SoC.

Specification:

  * MediaTek MT7620N (580 Mhz)
  * 64 MB of RAM
  * 16 MB of FLASH
  * 802.11bgn radio
  * 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
  * 2x external, detachable (LTE) antennas
  * UART header on PCB (57600 8n1)
  * 6x LED (GPIO-controlled)
  * 1x bi-color Signal Strength LED (GPIO-controlled)
  * 2x button
  * JBOOT bootloader

The status led has been assigned to the dwr-921-c1:green:sigstrength (lte
signal strength) led. At the end of the boot it is switched off and is
available for lte operation. Work correctly also during sysupgrade
operation.

Installation:
Apply factory image via d-link http web-gui.

How to revert to OEM firmware:
1.) Push the reset button and turn on the power. Wait until LED start
    blinking (~10sec.)
2.) Upload original factory image via JBOOT http (IP: 192.168.123.254)
3.) If http doesn't work, it can be done with curl command:
    curl -F FN=@XXXXX.bin http://192.168.123.254/upg
    where XXXXX.bin is name of firmware file.

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2018-04-04 08:42:35 +02:00
INAGAKI Hiroshi
e3bf92edf5 ramips: fix switch and MAC address for WHR-G300N
WHR-G300N has 5 ethernet ports (lan: 4, wan: 1), but there was no
correct configuration in 02_network script and 6 ports was configured
on the switch.
Also, since the MAC address was not acquired from factory partition,
incorrect values was set to LAN and WAN interfaces.

This commit fixes these issues.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-03-23 20:31:49 +01:00
Peter Lundkvist
d13b05741a ramips: add support for TP-Link TL-WR902AC v3
TP-Link TL-WR902AC v3 is a pocket-size dual-band (AC750) router
based on MediaTek MT7628N + MT7650E.

Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet

* MT7650 ac chip isn't not supported by LEDE/OpenWrt at the moment.
  Therefore 5Ghz won' work.

Flash instruction:

The only way to flash LEDE image in TL-WR902AC v3 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-tplink_tl-wr902ac-v3-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with the LAN port, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
[drop p2led_an pinmux, this pin isn't used as gpio, fix whitespace issues]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-03-18 22:22:38 +01:00
Pawel Dembicki
a5bd8de0bd ramips: add support for D-Link DWR-116-A1/2
The DWR-116-A1/2 Wireless Router is based on the MT7620N SoC.

Specification:

  MediaTek MT7620N (580 Mhz)
  32 MB of RAM
  8 MB of FLASH
  802.11bgn radio
  5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
  2x external, non-detachable antennas
  UART (J1 in A1, JP1 in A2) header on PCB (57600 8n1)
  6x LED (GPIO-controlled), 2x button
  JBOOT bootloader

Known issues:
WAN LED is drived by uartl tx pin. I decide to use this pin as
uartlite tx pin.

Installation:
Apply factory image via http web-gui.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-03-18 22:22:38 +01:00
Mathias Kresin
d482356322 ramips: mt7620n: add mdio node and disable port4 by default
Revert the changes I applied to aa5014dd1a ("ramips: mt7620n: enable
port 4 as EPHY by default").

The driver expects a node mdio-bus to be present, regardless of the
actual node status. If the node is missing the driver fails to load  with

  mtk_soc_eth 10100000.ethernet: no mdio-bus child node found

Disable port4 by default again. If the port is enabled but not present, a
"invalid port id 4" warning is shown during boot.

Fixes: FS#1428

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-03-13 20:18:15 +01:00
Giuseppe Lippolis
aa5014dd1a ramips: mt7620n: enable port 4 as EPHY by default
According to the datasheet the mt7620n have a fixed switch configuration
with 5 ephy (10/100) port. No RGMII configuration is possible.

Drop the mdio node as well. Without RGMII, the mdio node doesn't make any
sense

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
[drop mdio node, enable port4 by default]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-03-06 19:49:06 +01:00
Roman Yeryomin
f5984e0a0c ramips: mt7621: add Mediatek AP-MT7621A-V60 EVB support
This board has:
- mt7621 SoC
- 8MB SPI flash
- 128MB RAM
- 5x ethernet ports from internal (SoC) switch
- 1x ethernet port sitting on gmac2 and IC+ phy (not yet supported)
- 3x PCIe slots
- 1x USB 2.0 and 1x USB 3.0
- sound based on wm8960
- SDXC card slot (full size)

First fw write from interactive u-boot menu, interrupt with 2.
After that sysupgrade.

Tested both with 4.9 and 4.14

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-02-24 16:05:28 +01:00
Benjamin Valentin
2d8eeca842 ramips: enable power LED and second uart on GL-MT300N-V2
The device has a second uart accessible via pin headers, so enable it.

There is also a green power led which was not enabled previously.
Enable it too and use it as status LED.

Signed-off-by: Benjamin Valentin <benjamin.valentin@volatiles.de>
2018-02-23 07:54:29 +01:00
Piotr Dymacz
f1c193c27e ramips: add support for ALFA Network AWUSFREE1
ALFA Network AWUSFREE1 is an USB Wi-Fi N300 adapter based on MT7628.

Specification:

- MT7628AN (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (MT7628) with external FEM (RFFM4203)
- 2x detachable antennas (RP-SMA)
- ASIX AX88772 USB to Ethernet bridge (connected with MT7628 PHY0)
- 4x LED (2 driven by GPIO)
- 1x button (reset)
- 1x mini USB for host and main power input
- UART header on PCB

Flash instruction:

You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:

1. Power device with reset button pressed and release it after ~5 sec.
2. Setup static IP 192.168.1.2/4 on your PC.
3. Go to 192.168.1.1 in browser and upload "sysupgrade" image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 23:40:11 +01:00
Roman Yeryomin
6b6dc2b3e3 ramips: mt7621: fix usb init
In 4.14 reg-names is required to identify resources.
Otherwise init fails with:

[    5.900501] xhci-mtk 1e1c0000.xhci: invalid resource
[    5.910499] xhci-mtk: probe of 1e1c0000.xhci failed with error -22

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-02-22 17:25:38 +01:00
INAGAKI Hiroshi
e1d4aa36b0 ramips: add support for Tama W06
Tama Electric Axing W06 is a 2.4 GHz band 11n router, based on Mediatek
MT7688AN.

Specification:

- MT7688AN (575 MHz)
- 64 MB of RAM (DDR2 SDRAM)
- 16 MB of Flash (SPI)
- 1T1R 2.4 GHz
- 1x 10/100/1000 Mbps Ethernet
- 4x LEDs (GPIO connected: 3), 1x button
- 1x USB 2.0 Type-A (host)
- UART header on PCB (GND, RX, TX, Vcc from RJ45 side)

Flash instruction using sysupgrade image:
1. Connect micro-USB cable for power supply into W06 and turn on the
router
2. Connect to wifi with SSID "tama-*" with password. Complete SSID and
password are listed on the back of the router
3. Access to 192.168.1.1 and login with user name "admin" and password
empty
4. In firmware update(ファームウェア更新) page, click "参照" button
and click "ブラウザー" button to open file browser, select the
sysupgrade image and press OK button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-02-20 19:25:17 +01:00
Mathias Kresin
cb741654e5 ramips: improve GnuBee Personal Cloud Two support
Use the generic board detection for the GnuBee Personal Cloud Two
instead of the target specific one as all recent additions are doing.

Fixup the pinmux to set all pins used as GPIO to the function GPIO.
Request pins where used.

Drop the i2c from the dts. There is nothing connected. While at it fix an
indentation issue and use references instead of duplicating the whole
node path.

Use the same switch config as for the GB-PC1 and drop the led trigger for
the not supported IP1001 phy connected to second rgmii.

Fixes: c60a21532b ("ramips: Add support for the GnuBee Personal Cloud Two")
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
George Hopkins
13f9e40602 ramips: add support for D-Link DAP-1522 A1
D-Link DAP-1522 is a wireless bridge/access point with 4 LAN
ports and a dual-band wireless chipset.

Specifications:
- Ralink RT2880
- 32 MB of RAM
- 4 MB of Flash
- 4x 10/100/1000 Mbps Ethernet (RTL8366SR)
- 802.11abgn (RT2850)

Flash Instructions:
1. Download lede-ramips-rt288x-dap-1522-a1-squashfs-factory.bin
2. Open the web interface and upload the image

Signed-off-by: George Hopkins <george-hopkins@null.net>
2018-02-13 11:18:07 +01:00
Rosen Penev
c60a21532b ramips: Add support for the GnuBee Personal Cloud Two
The GnuBee Personal Cloud Two crowdfunded on https://www.crowdsupply.com
It is a low-cost, low-power, network-attached storage device.

Specifications:

- SoC: MediaTek MT7621AT
- RAM: DDR3 512 MB
- Flash: 32 MB
- Six SATA ports for 3.5" Drives
- One SDcard
- One USB 3.0
- Two USB 2.0
- Gigabit Ethernet: Three Ports
- UART 3.5mm Audio Jack or 3 pin header - 57600 8N1
- Three GPIOs available on a pin header

Flash instructions:

The GnuBee Personal Cloud Two ships with libreCMC installed.
libreCMC is a Free Software Foundation approved fork of LEDE/OpenWrt.
As such one can upgrade using the webinterface or sysupgrade.

Das U-Boot has multiple options for recovery or updates including :

- USB
- http
- tftp

Errata:
- While there are three ethernet ports, the third requires support for
  the second GMAC. This will come in kernel 4.14.
- The first hard drive slot has a clearance issue with the two fan
  headers. Workaround is to pull the headers out and connect the pins to
  jumper wires.
- Using this device as a NAS is problematic with the 4.9 kernel as many
  /dev/sdX reads throw silent errors. The current theory behind this is
  some kind of unhandled DMA mapping error in the kernel. This is not an
  issue with kernel 4.4.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-02-13 10:01:52 +01:00
Henryk Heisig
14951e8f8e ramips: add support for TP-Link Archer C50 v3
TP-Link Archer C50 v3 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7612E.

Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power switch

* WAN LED in this devices is a dual-color, dual-leads type which isn't
  (fully) supported by gpio-leds driver. This type of LED requires both
  GPIOs state change at the same time to select color or turn it off.
  For now, we support/use only the green part of the LED.

Flash instruction:

The only way to flash LEDE image in ArcherC50v3 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ramips-mt7628-ArcherC50v3-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2018-02-11 16:04:16 +01:00
Henryk Heisig
e39a240ba2 ramips: ArcherC20v4: use common TP-Link dtsi file
and remove common part from dts file.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2018-02-11 16:04:16 +01:00
Henryk Heisig
368a7f4cec ramips: change the TP-Link dtsi filename
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2018-02-11 16:04:16 +01:00