Changed default role of Orange Pi PC2 MSUB port to host (in dts)
Changed default function of Orange Pi PC2 power button to PWR_BTN
Signed-off-by: Antonio Silverio <menion@gmail.com>
CPU: H5 High Performance Quad-core 64-bit Cortex-A53
GPU: Mali450 OpenGL ES 2.0/1.1/1.0, OpenVG 1.1, EGL
Memory: 1GB DDR3 (shared with GPU)
Onboard Storage: TF card (Max. 32GB) / NOR flash(2MB)
Onboard Network: 1000M/100M Ethernet RJ45
USB 2.0 Ports: Three USB 2.0 HOST, one USB 2.0 OTG, HOST mode
role by default in DTS
Buttons: Power Button(SW4) Debug TTL
UART: ..DC-IN..
>[GND][RX][TX] ..HDMI..
Signed-off-by: Antonio Silverio <menion@gmail.com>
When checking the outcome of the PHY autonegotiation status, at803x
currently returns false in case the SGMII side is not established.
Due to a hardware-bug, ag71xx needs to fixup the SoCs SGMII side, which
it can't as it is not aware of the link-establishment.
This commit allows to ignore the SGMII side autonegotiation status to
allow ag71xx to do the fixup work.
Signed-off-by: David Bauer <mail@david-bauer.net>
The QCA955X is affected by a hardware bug which causes link-loss of the
SGMII link between SoC and PHY. This happens on change of link-state or
speed.
It is not really known what causes this bug. It definitely occurs when
using a AR8033 Gigabit Ethernet PHY.
Qualcomm solves this Bug in a similar fashion. We need to apply the fix
on a per-device base via platform-data as performing the fixup work will
break connectivity in case the SGMII interface is connected to a Switch.
This bug was first proposed to be fixed by Sven Eckelmann in 2016.
https://patchwork.ozlabs.org/patch/604782/
Based-on-patch-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit adds the ability to configure specific functions of the
at803x series ethernet-PHYs, which were previously configured
exclusively with the help of platform-data, via device-tree.
This is needed to fully support existing boards of the ar71xx platform.
Signed-off-by: David Bauer <mail@david-bauer.net>
Backport an upstream fix for a remotely exploitable TCP denial of service
flaw in Linux 4.9+.
The fixes are included in Linux 4.14.59 and later but did not yet end up in
version 4.9.118.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The QCA9557 dtsi is currently missing pll-handle and pll-regs for both
eth0 and eth1, therefore PLL settings won't be applied. This commit
fixes this behavior.
Signed-off-by: David Bauer <mail@david-bauer.net>
While finalizing support for the U7623 with 512MB, I made an embarresing
error and configured 1GB RAM for the board. I also forgot to move memory
from the dtsi and to the dts. This commit takes care of my mistakes.
While I am confessing my mistakes, I also note that I made a mistake in
the commit message of the initial U7623 commit. It is the .bin-file, and
not the .gz file that shall be sent to the device via tftp.
v1->v2:
* Remove redundant memory node (thanks Jonas Gorski)
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Including the tl-wdr3600 image build code just to overwrite most of it
doesn't make much sense and only makes it hard to read.
Furthermore, the tl-wdr4300 image will be marked as compatible with the
tl-wdr3600 this way.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The variables are used in image build recipes and need to be marked as
per devices vars to be stored individual per image define. Otherwise
the last defined variable will be used for all boards.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch did the following things:
1. Separate ath9k-leds out of gpio leds so that all other leds will work
before ath9k loded (e.g. during preinit/init stage).
2. Rename wps led to qss since that's how TP-Link mark it.
3. Rename LED prefix to tp-link because that dts is shared by many devices.
4. Rename to wr740n-v1 because v1 is the first and v2 just use the fw of v1.
(This will require a forced sysupgrade if you comes from
the previous wr740n v2 image.)
5. Remove SUPPORTED_DEVICES.
(tl-wr740n-v2 doesn't exist anywhere so it's useless.)
6. Add all WR741ND v1 clones found in ar71xx.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Fix all issues found by the devicetree compiler like wrong address/size
cells as well as wrong/missing/superfluous unit addresses.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use only the jedec,spi-nor compatible string. Everything else either
never worked or is only support to keep compatibility.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the same method for setting queue index pointers consistenly
throughout the source file.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This router is called Archer C7 and the tl was used to identify
TP-LINK. Since we have added tplink in dts/board name, the tl
prefix is useless now.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Change lan and it's LED to eth0
It's broken since c7c807cb8c
where I changed the dts but forgot to change default configurations.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
1. Swap eth0/eth1
Both devices are using AR9331, the builtin switch on AR9331 is
connected to gmac1 and gmac1 is named as eth1 in ath79.
PS: gmac1 is eth0 and gmac0 is eth1 in ar71xx because of the
reversed initialization order.
2. Fix the incorrect compatible string in dts
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
phy-handle is used to poll link status. They are useless when
we need fixed-link on these interfaces.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Jonas Gorski commented on the previous patch:
|This is actually the wrong fix and papers over an issue in one of our
|local patches.
|
|We intentionally allow regmap to be built as a module, see
|
|/target/linux/generic/hack-4.14/259-regmap_dynamic.patch
|[...]
|[The regulator code] optionally supports regmap thanks to the stubs
|provided if regmap is disabled - which breaks if you compile regmap
|as a module.
In order to mitigate this issue, this patch reverts the previous patch
and replaces the existing IS_ENABLED(CONFIG_REGMAP) with
IS_REACHABLE(CONFIG_REGMAP). This solves this particular issue as the
regulator code will now automatically fallback to the regmap stubs in
case the kmod-regmap module is enabled, but nothing else sets
CONFIG_REGMAP=y.
Note: There's still a potential issue that this patch doesn't solve:
If someone ever wants to make a OpenWrt kernel package for a
regulator module that requires the REGMAP feature for a target that
doesn't set CONFIG_REGMAP=y but has CONFIG_REGULATOR=y, the resulting
kmod-regulator-xyz package will not work on the target.
Luckily, there aren't any in-tree OpenWrt kernel module packages for
regulators at the moment. On the bright side: regmap is a critical
part nowadays and all new and upcoming architectures require it by
default. This will likely only ever be a problem for legacy targets
and devices that cannot afford to enable REGMAP.
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Cc: John Crispin <john@phrozen.org>
Fixes: d00913d121 ("kernel: modules: fix kmod-regmap")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
To share mdio addr for IntPHY and ExtPHY,
as described in the documentation (MT7620_ProgrammingGuide.pdf).
(refer: http://download.villagetelco.org/hardware/MT7620/MT7620_ProgrammingGuide.pdf)
when port4 setup to work as gmac mode, dts like:
&gsw {
mediatek,port4 = "gmac";
};
we should set SYSCFG1.GE2_MODE==0x0 (RGMII).
but SYSCFG1.GE2_MODE may have been set to 3(RJ-45) by uboot/default
so we need to re-set it to 0x0
before this changes:
gsw: 4FE + 2GE may not work correctly and MDIO addr 4 cannot be used by ExtPHY
after this changes:
gsw: 4FE + 2GE works and MDIO addr 4 can be used by ExtPHY
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
When PHY's are defined on the MDIO bus in the DTS, gigabit support was
being masked out for no apparent reason, pegging all such ports to 10/100.
If gigabit support must be disabled for some reason, there should be a
"max-speed" property in the DTS.
Reported-by: James McKenzie <openwrt@madingley.org>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Mediatek has a reference platform that pairs an MT7620A with an MT7530W,
where the latter responds on MDIO address 0x1f while both chips respond on
0x0 to 0x4. The driver special-cases this arrangement to make sure it's
talking to the right chip, but two different ways in two different places.
This patch consolidates the detection without the current requirement of
both tests to be separately satisfied in the DTS.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
This really simplifies debugging, if a package is not found or a feed is
not reachable, a proper stderr is printed. Currently it would only say
`_call_manifest` failed.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Starting with kernel 4.4, the use of partitions as direct subnodes of the
mtd device is discouraged and only supported for backward compatiblity
reasons.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
Fix space vs. tabs issue and trainling whitespaces. Use C style
comments or drop the comments if they explain what is already to see in
the devicetree parameters.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The hardware NAT node has the same reg/unit as the ethernet node. One
of them need to be a child of the other.
Make the hardware NAT node a child of the ethernet node since the it
"reference" the netdev in its properties.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add the ranges property to the PCI bridges where missing. Add the unit
address to PCI bridge where missing.
Rework the complete rt3883 pci node. Drop the PCI unit nodes from the
dtsi. They are not used by any dts file and should be rather in the dts
than in the SoC dtsi. Express the PCI-PCI bridge in a clean devicetree
syntax. The ralink,pci-slot isn't used by any driver, drop it. Move the
pci interrupt controller out of the pci node. It doesn't share the same
reg and therefore should be an independent/SoC child node.
Move the pci related rt3883 pinctrl setting to the dtsi instead of
defining the very same for each rt3883 board.
If the device_type property is used for PCI units, the unit is treated
as pci bridge which it isn't. Drop it for PCI units.
Reference pci-bridges or the pci node defined in the dtsi instead of
recreating the whole node hierarchy. It allows to change the referenced
node in the dtsi without the need to touch all dts.
Fix the PCI(e) wireless unit addresses. All our PCI(e) wireless chips
are the first device on the bus. The unit address has to be the bus
address instead of the PCI vendor/device id.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Since commit c1e7738988f5 ("checks: add gpio binding properties check")
dtc treats any *-gpios and *-gpio property as phandle at least during
checks. The only whitelisted property is nr-gpio.
Use ralink,nr-gpio in favour of ralink,num-gpios to get rid of false
positive warnings.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The cpu interrupt controller doesn't have a reg property, hence we
can't use a unit address in the node name.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Without this patch you will get an error "gpio-export probe deferral
not supported" when you try to export i2c expander gpio pins.
gpio-export is probed long before i2c-bus and i2c expander are created
and it doesn't retry it so none pins are exported.
Signed-off-by: René van Dorst <opensource@vdorst.com>
apply the change to all instances of the gpio exports patch
Signed-off-by: Mathias Kresin <dev@kresin.me>
Revert 290c54473e ("ath79: fix TP-Link Archer C7 v2 wlan1 MAC address")
which obviously aims to have a distinct MAC address per interface.
Unfortunally it doesn't match what is used by the stock firmware and we
shouldn'z use MAC Adresses not reserverd for/assigned to a particular
board.
The correct MAC adress increments for this board are:
wlan0 (5GHz) : -1
wlan1 (2.4GHz) : 0
eth1 (LAN) : 0
eth0 (WAN) : 1
Fixes: FS#408
Signed-off-by: Mathias Kresin <dev@kresin.me>
The Linux headers on arm64 architectures contain references to common
arch/arm/ headers which were not bundled by the SDK so far.
Check if we're packing the SDK for an arm64 target and if we do, also
include arch/arm headers as well.
Fixes FS#1725.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
It seems to have been missed when the patch was accepted.
Fixes: d591260407 ("brcm63xx: initial support for Sky SR102 router")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The integrated SoC wifi will likely never be supported, and if,
it will go through DT with the sprom contents there.
Fixes: d591260407 ("brcm63xx: initial support for Sky SR102 router")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Adds Support for the TP-LINK CPE510 V2.0 by TP-Link.
The hardware is almost the same as the CPE510 V1.0
Follow the same processes as for the CPE510 V1.0
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
1) Add comments so it's clear why we did things; this may prevent
someone (e.g. me) from sinking time into fixing things that
aren't broken and/or were done for reason.
2) Drop mdio 0 probe/register; we don't use ag1xx mdio bus 0.
3) Cosmetic reording of some code (tested) that makes the defintion
more clear.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
The CR3000 stock firmware is now irrelevant as it required a now defunct
cloud service. Therefore only build images that use the entire flash
(overwriting stock firwmare-specific partitions that no longer matter),
previously called 'nocloud' images.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
The PowerCloud Systems CR3000 was a cloud-managed CPE for a now defunct
NaaS offering. It was previously supported under the ar71xx branch and
this forward ports that support with some notable differences:
1) Since reverting to stock firmware is now irrelevant there is is only
a single openwrt image generated which uses the entire flash rather than
preserving PowerCloud-specific partitions that are unneeded to openwrt--
those partitions will be erased and used by the openwrt image.
2) Rather than use a non-standard probe order for the ethernet devices,
this image uses a set of 'ip link set ethX name ethY' commands very early
in preinit (before the network is used at all), in order to have the the
switch and Wan use the same ethernet names as in previous images.
3) /etc/config/wireless will need to be regenerated as the path to the
wireless device has changed due to differences in ath79 DT for ar93x
compared to ar71xx images.
4) eth0 is wan and eth1 is lan (switch)
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
Refreshed all patches
Remove upstreamed patches.
- 103-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch
- 403-mtd_fix_cfi_cmdset_0002_status_check.patch
- 001-4.11-01-mtd-m25p80-consider-max-message-size-in-m25p80_read.patch
- 001-4.15-08-bcm63xx_enet-correct-clock-usage.patch
- 001-4.15-09-bcm63xx_enet-do-not-write-to-random-DMA-channel-on-B.patch
- 900-gen_stats-fix-netlink-stats-padding.patch
Introduce a new backported patch to address ext4 breakage, introduced in 4.9.112
- backport-4.9/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch
This patch has been slightly altered to compensate for a new helper function
introduced in later kernels.
Also add ARM64_SSBD symbol to ARM64 targets still running kernel 4.9
Compile-tested on: ar71xx, bcm2710
Runtime-tested on: ar71xx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Bundle the usbip utility sources shipped with the Linux kernel tree in
order to allow the usbip packages from the package feed to build within
the OpenWrt SDK.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
In 4.14.57, a new symbol for Spectre v4 mitigation was introduced for
ARM64. Add this symbol to all ARM64 targets using kernel 4.14.
This mitigates CVE-2018-3639 on ARM64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
AT803X_REG_CHIP_CONFIG and AT803X_BT_BX_REG_SEL have been defined
upstream by commit f62265b53ef3 ("at803x: double check SGMII side autoneg")
An existing local patch then added those exact same defines again which
isn't necessary, so remove them.
Fixes: f791fb4af4 ("kernel: add linux 4.9 support")
Fixes: b3f95490b9 ("kernel: generic: Add kernel 4.14 support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The patch was wrongly removed by a kernel version bump to 4.9.105 in
the believe that it was merged upstream thow it wasn't. This lead to
unrecoverable link losses on devices which use those PHYs such as
many ubnt single-port CPEs.
Fixes: 7dca1bae82 (kernel: bump to 4.9.105)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The previous round of fixes for the 82574 chip cause an issue with
emulated e1000e devices in VMware ESXi 6.5. It also contains changes
that are not strictly necessary. These patches fix the issues introduced
in the previous series, revert the unnecessary changes to avoid
unforeseen fallout, and avoid a case where interrupts can be missed.
The final two patches of this series are already in the kernel, so no
need to include them here.
Patchwork: https://patchwork.ozlabs.org/cover/881776/
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This changes the DT binding's compatible property to
"ecoscentric,redboot-fis-partitions", removing the existing reference to
Red Hat.
Per the documentation hosted at eCosCentric's website, eCosCentric is
RedBoot's sole commercial maintainer since 2002, and the project has
been under the stewardship of the Free Software Foundation since 2008.
This also updates the property in the Inventel Livebox 1 .dts, the
binding's only current user.
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
The OpenMesh A62 is a tri-band device (1x 2.4GHz, 2x 5GHz) with special
filters in front of the RX+TX paths to the 5GHz PHYs. These filtered
channel can in theory still be used by the hardware but the signal strength
is reduced so much that it makes no sense.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
In the new DT-based pci-ar71xx driver, ar71xx_pci_irq_init() was being
called before populating the PCI controller's device_node struct member.
This led to no IRQ being assigned to connected PCI devices (e.g. ath9k
cards) and caused them to be non-functional aside from simply being
detected.
The previous errors encountered in dmesg were: "irq: no irq domain found
for /ahb/apb/pcie-controller@180c0000 !". /proc/interrupts listed an IRQ
of 0 for the cards.
While this has been only been tested on a yet-to-be-merged RouterStation
Pro target, it should also fix the broken wifi people have reported for
the ath79 WNDR3800 target.
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
Add missing definitions for the orange WAN LED on the
TL-WR1043N(D) v4 and v5.
Change the name of a MAC address offset constant to
make it consistent with the format of the
existing constants.
Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
ELECOM WRC-2533GST is a 2.4/5 GHz band 11ac rotuer, based on
MediaTek MT7621A.
Specification:
- MT7621A (2-Core, 4-Threads)
- 128 MB of RAM (DDR3)
- 16 MB of Flash (SPI)
- 4T4R 2.4/5 GHz wifi
- MediaTek MT7615
- 5x 10/100/1000 Mbps Ethernet
- 4x LEDs, 6 keys (2x buttons, 1x slide switch)
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- baudrate: 57600 bps
Flash instruction using factory image:
1. Connect the computer to the LAN port of WRC-2533GST
2. Connect power cable to WRC-2533GST and turn on it
3. Access to "https://192.168.2.1/" and open firmware update
page ("ファームウェア更新")
4. Select the OpenWrt factory image and click apply ("適用")
button
5. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Tested with 18.06.0-rc2/ar71xx/generic/tl-wdr4300-v1, image & list
This PR is based on the work of @fewckert[1] with slight improvements.
Add function `manifest` to show the manifest of the produced image,
before actually building it. The manifest contains an orderd list of
package name and version.
This is usefull to check package dependencies but also determine a
unique and reproducible image name before building the package. The
sysupgrade server[2] builds images on request with individual package
selection. To distignish between created images which contain differnt
packages, the EXTRA_IMAGE_NAME is set to a shortend hash of the
manifest's content. So far the image was renamed afterwards as the
manifests content was unknown, however this corrupts the signed
sha256sums. This patch allows a clean solution as to dtermine the
manifest in advance and set the EXTRA_IMAGE_NAME accordingly.
[1]: https://github.com/lede-project/source/pull/1591
[2]: https://github.com/aparcar/attendedsysupgrade-server
Signed-off-by: Paul Spooren <mail@aparcar.org>
TP-Link Archer C59v2 is a dual-band AC1350 router based on
Qualcomm/Atheros QCA9561+QCA9886 chips.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- UART header on PCB
Flash instruction:
- via web UI:
1. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin
2. Login to router and open the Advanced tab
3. Navigate to System Tools -> Firmware Upgrade
4. Upload firmware using the Manual Upgrade form
- via TFTP:
1. Set PC to fixed ip address 192.168.0.66
2. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin
and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Keith Maika <keithm@aoeex.com>
This fixes:
drivers/mtd/redboot.c:299:34: error: array type has incomplete element type 'struct of_device_id'
Fixes: 5e8b4be531 ("kernel: add DT binding support to the mtd redboot parser")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
linux,part-probe should be avoided as its only supported with OpenWrt
downstream patch that is going to be dropped eventually.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
On brcm47xx boards, the model ID is the combination of the "boardtype" nvram
variable and an optional supplemental "boardnum" variable while the human
readable model name is usually exposed in the "machine" field of the
/proc/cpuinfo file.
Move the extraction of the board nvram variables and model name string into
the 01_sysinfo file and rework the 01_detect board configuration script to
solely use the prepared sysinfo values without performing own detection
logic.
As a consequence, we can drop the ucidef_set_board_id() and
ucidef_set_model_name() invocations in favor to the generic behaviour
which copies the /tmp/sysinfo/{board_name,model} values into the board.json
"id" and "name" fields respectively.
Since "01_detect" only contains network configuration logic after this
change, move it to "01_network" and rename the contained "detect_by_xxx"
functions to "configure_by_xxx" instead, to avoid potential confusion.
Fixes FS#1576
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
fixes FS#1034, squash fs images fails to boot because of missing ARM BCJ filter decoder
also activate squashf image creation
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
The Traverse LS1043-S board is a router board based on
NXP/Freescale's LS1043 SoC, with 4x1GBase-T, 1 SFP and 1 SFP+,
as well as miniPCIe and M.2 LTE.
Unlike the Layerscape reference boards, the LS1043-S board has
NAND flash and uses the mainline U-Boot.
This patch implements support for the LS1043-S board, as well as
the earlier LS1043-V board. It is our intention that all boards
in this family (LS1043-S and later, Five64) will boot the same binary.
Not included in this patchset are the hwmon drivers not in the kernel
(emc1704,pac1934) or the bootloader.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
This is required for the Traverse LS1043 family, we generate a FIT image
that works on all boards across the family. This is done by creating
multiple configurations that select the right DTB for the board.
The bootloader on these boards is configured to boot like this:
bootm $kernel_load#ls1043s
bootm $kernel_load#ls1043v
This is based on earlier work by Jason Wu for Zynq:
https://lists.openwrt.org/pipermail/openwrt-devel/2016-March/040460.html
Modified to add FDT load addresses and multiple configurations with DTB.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
This is required on the Traverse LS1043 boards to support SFP
and xDSL plug-ins.
This will not be needed on kernel 4.14.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
In boards with fdt is impossible to use kmod-w1-gpio-custom.
w1-gpio-custom create platform structure for w1-gpio module,
but if board use fdt, data is ignored in w1-gpio probe.
This workaround fix the problem.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The device name is corrected to match the hardware-stored (in hard config
flash space) device name.
Tested-by: Tobias Schramm <tobleminer@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
The device name is corrected to match the hardware-stored (in hard config
flash space) device name.
Tested-by: Tobias Schramm <tobleminer@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Tested on HC5661A and it now fixes the issue that when enabling sd card
in HC5661A, the wan and 3 lan ports will down.
Known issue:
- When enabling SD card support, the led light of system will down and the rest 2 lights keep working.
Signed-off-by: LoveSy <shana@zju.edu.cn>
There is another thing about crc to do when initialize SD card on
MT7628.
This commit is to fix this init issue.
Signed-off-by: LoveSy <shana@zju.edu.cn>
Qxwlan E750G v8 is based on Qualcomm QCA9344.
Specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4G GHz (AR9344)
- 2x 10/100 Mbps Ethernet (PoE support)
- 2x 10/100/1000 Mbps Ethernet
- 7x LED (6 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J23) and LEDs (J2) headers on PCB
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
Qxwlan E750A v4 is based on Qualcomm QCA9344.
Specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 5G GHz (AR9344)
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (USB 2.0 bus only)
- 7x LED (6 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J23) and LEDs (J2) headers on PCB
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
Qxwlan E558 v2 is based on Qualcomm QCA9558 + AR8327.
Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (QCA9558)
- 3x 10/100/1000 Mbps Ethernet (one port with PoE support)
- 4x miniPCIe slot (USB 2.0 bus only)
- 1x microSIM slot
- 5x LED (4 driven by GPIO)
- 1x button (reset)
- 1x 3-pos switch
- 1x DC jack for main power input (9-48 V)
- UART (JP5) and LEDs (J8) headers on PCB
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
The driver is written in such a way that with a board defintion that
connects a fixed phy, mdio, and switch in a certain way, a kernel oops could
result because of lack of previously probed mdio bus.
This commit allows for easier debugging in this case by casting the
correct blame with serial console messages.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
It's a little noisier but makes it obvious when the ar7240 switch was
connected to the MDIO bus, and to which phy device (or the failure
to do so).
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
NB: Error only appears with ag71xx debug messages and dynamic printk
enabled. This is probably why no one has caught it before.
Previously phy probe debug messages used old (now wrong) functions
to get the phy name for printing. There was also the chance of
a NULL pointer in the event no phy_device was found.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
mdio bus isn't a standalone device on ar7240. (and maybe older SoCs?)
Use simple-mfd for ar7241 and later SoCs to get mdio1 ready before gmac0
For ar7240 and older chips, manually create platform device after
ag71xx_hw_init() in ag71xx_probe()to get mdio0 ready between
ag71xx_hw_init() and ag71xx_phy_connect().
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Allow specifying desired mdio clock frequency in dts.
Use default frequency around 5MHz for builtin switch and 2MHz for other mdio bus.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Remove mdio1 and phy1 handle. AR8327N is controlled through mdio0.
Add gmac-config for Archer C7.
Remove ucidef_set_interfaces_lan_wan. They can be determined by config_generate automatically.
The following are for adding support for WDR4900 v2/Archer C7 v1 and other
devices that shared the same machine file in ar71xx:
Move mtd partitions to archer-c7-v2.dts. Only Archer C7 v2 has 16M flash.
Flash on Archer C7 v1/TL-WDR4900 v2 is 8M.
Add label for wlan leds. The default trigger for archer c7/wdr4900 is different.
Move wlan5g led to archer-c7-v2.dts. 5G led on WDR4900 is connected to ar9380.
Move rfkill definition to archer-c7-v2.dts. There is no such a button on wdr4900 v2.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
enable mdio1 by default because mdio1 node is a subnode of eth1
and eth1 node is a "simple-mfd", which makes mdio1 disabled when
eth1 isn't enabled.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Most qca devices use 115200n8 as it's default uart baudrate.
Add 'chosen' node for qca953x like other SoCs in ath79 target.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Commit c7efc93 renamed controller name
to qca,ar9340-intc and added some functions but qca9533.dtsi was overlooked.
Correct the dtsi and adust it to the new format
Add gmac and correct reset for cascaded irq and build-in switch
Also add the reference clock to soc dtsi so we don't have to have it in every dts
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
Remove switch reset definition
Fix gmac compatible string (We only need SW_PHY_SWAP and SW_PHY_ADDR_SWAP on qca953x so use ar9330-gmac instead of ar9340-gmac.)
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
gmac0 is always connected to switch phy4 and mdio1 is always needed.
So add phy handle for eth0 and enable mdio1 by default.
Move fixed-link for gmac1 from device dts to ar9331.dtsi because gmac1 is always connected to builtin switch.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Enable mdio1 by default because mdio1 is needed when eth1 is enabled.
PS: If a ar9341 device has only one port and you only want to use gmac0,
change compatible of gmac1 to "syscon", "simple-mfd" in dts.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This patch did several things:
1. Probe the builtin switch as a separated mdio device.
2. Register a separated mdio bus for builtin switch.
3. Use generic mdio read/write function instead of calling ag71xx_mdio_mii_read/write directly.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
We need to have mdio1 belonging to gmac1 initialized before gmac0.
Split it into a separated mdio device to get both mdios ready before probing gmac.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The builtin switch has it's initial valid mac address(00:00:01:00:00:00).
Since the builtin switch is an independent device, setting mac address of gmac1 to builtin switch isn't a good idea and this makes it impossilbe to split builtin switch apart as an independent platform device.
Remove these functions and apply default VLAN during initialization as a preparation for further driver splitting.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Only build images for straight OpenWrt (using all flash; wipes out
partitions that contain information only important for accessing a
now defunct cloud service with the stock firmware) since the stock
firmware is now irrelevant.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
The wrong MAC addresses (from the point of view of the physical device
label) were being assigned to the wrong interfaces. Fix that.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
While the stock firmware and previous ar71xx versions of openwrt used the
single ethernet port as a DHCP client, for unmodified openwrt usage it
makes more sense to do the standard openwrt thing and make the ethernet
port a static lan with known address so that users can find the device on
the network more easily.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
The Skydog cloud service no longer exists hence supporting going back
to stock firmware with cloud support is no longer applicable.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
The reset button was incorrectly returning KEY_WPS_BUTTON as the key
code. We want KEY_RESTART., so make that fix.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
The PCIe wireless MAC address address is better labelled as WMAC
than MAC to emphasize that it is for a wireless interface.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
The CAP324 was an AP for a NaaS offering that is now defunct. While
previously supported in the ar71xx arch, there were some errata (to
be fixed shortly).
Notable differences from ar71xx support:
1) The method of getting the ath9k firmware for the PCIe 2ghz wifi has
changed (due to changes in how the arch handles this), since this device
doesn't use the EEPROM except to get the MAC address of the wifi.
2) /etc/config/wireless will need to be regenerated as the path(s) to
the wireless device(s) have changed.
3) ath79 OpenWrt firmware no longer supports build an image that allows
reverting to stock firmware (as the cloud service no longer exists, the
stock firmware is useless), instead using all of the flash for image and
overlay (less u-boot/env and art).
4) Initial network config treats the ethernet port as a Lan port with
the standard default address (192.168.1.1 unless changed in .config
--e.g. via menuconfig) instead of using DHCP (this was the default for
the stock firmware, however for openwrt use this is rather confusion and
counter-productive as the user has a harder time finding the device on
the network.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
Add ath79 arch support for PowerCloud Systems CR5000. Previously
supported under ar71xx (however there are some errors in that support;
to be fixed shortly).
Info:
* This board is based on the Atheros DB120 reference design, but doesn't
use the on-board switch. Instead it attachs GMAC0 to an AR8327 switch.
* It only uses GMAC0 and the WAN is simply a VLAN in the stock firmware.
* It has 64MB RAM and 8MB flash.
* In the dts version we get rid of using 'open-drain' for the AR8327
LED controls.
* As with the platform data version we disable JTAG as this conflicts
with one of the pair of GPIO's required for the power/status LED
(GPIO2 and GPIO4 are used for this LED).
* The pcie card wifi has an EEPROM but gets it's MAC address from
the ART partition.
* The SoC wifi (2.4 GHz) is all from the ART.
* The USB is support comes from the SoC.
NB. This is actually an AR9342 rather than AR9344 but we use the 9344
definitions because there are no relevant differences for this board.
NB: Building only images that don't support reverting to the old
cloud-based firmware as the Skydog cloud service for the CR5000 no
longer exists.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
81d446b045 introduced incomplete
support for this device.
This patch attempts to correct the situation based on OEM source
code.
LED1-3 are GSM mode on OFW (2G/3G/4G) hence unassigned here.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Tested-by: David Ehrmann <ehrmann@gmail.com>
The active_low flag was missing for the user LED. This LED is open drain
(confirmed in OEM source) and open drain only makes sense for active low
GPIOs.
The two wireless LEDs mentioned in the comments are also #defined for
future reference.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Tested-by: Ryan Mounce <ryan@mounce.com.au>
e15c63a375 introduced code that was trying
to register GPIO 1 as both an LED and a button. The OEM source makes it
clear that LED1 is not wired to the SoC GPIOs. GPIO 1 is the reset button.
Furthermore the (green) power led default state should also be defined,
(matching OEM source), and it should be used by diag.sh since it's
currently the only software-controllable LED.
This patch fixes these issues and renames the corresponding #defines for
clarity
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
The gpios that control power toggle for USB on the RouterBOARD devices
are active low _off_ switches.
When they are active (low), power is off. When they are inactive
(high), power is on.
Rename GPIO defines, set gpios to GPIOF_ACTIVE_LOW for consistency and
reflect their true action in the display name. This brings openwrt code
in line with OEM.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Tested-by: Ryan Mounce <ryan@mounce.com.au>
convert the usb and both sata port power related gpio-hogs to
what they really are: fixed-regulators.
The ethernet phy-reset gpio-hog is replaced by a proper
upstream (4.15+) reset-gpios property in the mdio-node.
So this will work eventually.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
@vahid-dan reported a issue with extracting the rpi images with
Gnome's Archive Manager:
"Ubuntu Archive Manager cannot extract the file and it just
throws a general error message: "An error occurred while
extracting files".
<https://forum.lede-project.org/t/corrupted-pre-built-v18-06-0-rc2-image-for-rpi>
The MBL's rootfs.img.gz image is generated in much the same way.
Hence this patch preemptively splits the rootfs.img.gz image into
a sysupgrade and a factory image.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds support for squashfs as the root filesystem.
advantages:
- migrate from a existing -ext4 installation and back
with the sysupgrade utility
- existing partition layout will not be lost during switch
- slightly smaller image size as compared to the -ext4 image.
disadvantages:
- needs f2fs + tools. This is because fstools rootdisk.c decides based
on the partition size (currently root partitions > 100 MiB) f2fs is
used as the rootfs_data filesystem.
- rootfs_data is placed into the rootfs partition after the squashfs.
This makes it difficult for tools that expect a /dev/sda${X} device.
It also makes it difficult for data recovery tools as they might not
expect to find a embedded partition or will be slightly confused.
... or will not support f2fs.
For people with existing build configurations: make sure to include mkf2fs
and f2fsck packages into the image. Otherwise the new -squashfs image will
only boot from the ram-overlay.
Note:
All overlay data (configurations/all installed packages/...) will be
placed in inside the rootfs partition (i.e. /dev/sda2) just after the
squashfs image.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
@vahid-dan reported a issue with extracting the rpi images with
Gnome's Archive Manager:
"Ubuntu Archive Manager cannot extract the file and it just
throws a general error message: "An error occurred while
extracting files".
<https://forum.lede-project.org/t/corrupted-pre-built-v18-06-0-rc2-image-for-rpi>
@blogic told me to split the single sdcard.img.gz for the RPi
into a sysupgrade and a factory image for all brcm2708 targets.
The factory images will have no metadata attached, this way
these utilities that can't deal with the attached metadata will
not fail for no reason.
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
It was present as 4.4 compatibility, but since we now use 4.9 or later
with the new upstream solution, we don't need it anymore.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
That upstream commit caused instability in flash reads. It was reported
but there isn't any proper fix as for now.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This includes Linksys EA9500 support, BCM53573 timer fix and
upstream-ready partitions patch that replaces two downstream hacks.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
USB 3.0 PHY is attached to the MDIO bus and should be supported
(accessed) as a MDIO device. This wasn't known initially which resulted
in writing driver that was working with MDIO bus (using some magic
values) without knowing it.
This commit updates DT to properly describe MDIO & USB 3.0 PHY and
enables required kernel drivers.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This is a new & warm feature that allows nesting partiitons in DT and
mixing their types (e.g. static vs. dynamic). It's very useful for
boards that have most partitions static but some of them require extra
parsing (e.g. a "firmware" partition).
It's required to successfully backport support for new devices using
that new syntax in their DT files.
Since brcm63xx has a custom alternative patch the upstream one is being
reverted for it. The plan is to make brcm63xx use the upstream
implementation.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The OCEDO Raccoon only has one ethernet port, but currently uci sections
for WAN and LAN are created.
Additionally, newer versions of the devices U-Boot (units with SteelWRT)
set the kernel-cmdline and therefore overwrite the partition-layout.
We fix this by overwriting the cmdline supplied by the bootloader.
Signed-off-by: David Bauer <mail@david-bauer.net>
The get_status_led() function was removed due to the convertion to dts
alias based status led.
Since we don't need the boardname any longer, the functions.sh include
isn't required any more.
Fixes: c9c4b2116c ("ramips: Use dts alias based status led")
Signed-off-by: Mathias Kresin <dev@kresin.me>
With a10a204aab ("kernel: make ubi auto-attach check for a tar file
magic") the check for the magic was added without considering a failing
mtd_read(). If the read fails, no check is done and the mount code is
called straight away.
Failing with an error message for such cases seems to me the cleaner way,
as it would allow to spot hidden/workaround issues.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The first block(s) of the ubi mtd device might be bad. We need to take
care on our own to skip the bad block(s) and read the next one(s).
Don't treat recoverable read errors as fatal and check for the UBI magic
if the data of a block could be recovered using ECC or similar.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Move the put_mtd_device() called on multiple error conditions to a goto
label to use it later for more error conditions.
The early return on failed open of the mtd device and mismatching mtd
type allows to get rid of one level of indentation. By jumping to the
cleanup code, a refcount bug is fixed for the wrong flash type condition.
While at it, make clear that we only check for the UBI magic if the read
from flash was successful.
Signed-off-by: Mathias Kresin <dev@kresin.me>
By takimata:
"Come to think of it, an MBL Single board boots up just fine on an
MBL Duo image, and the MBL Single board identifies completely
identical to the MBL Duo
(Board: Apollo-3G - APM82181 Board, 2*SATA, 1*USB).
I wonder if there is any downside to just using the MBL Duo firmware
on a MBL Single. I wonder if the two firmwares could even be unified."
<https://forum.lede-project.org/t/wd-mybook-live-duo-two-disks/16195/9>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
All these devices share the exact same image format.
The usb3 kmod is added for the rbm11g, as the rbm11g has a mini-pcie
slot like its bigger sibling. The usb kmod is necessary for
usb-over-pcie support, which is mandatory for a lot of LTE modules.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
The FritzBox 7312 is also known as 1&1 WLAN-MODEM. The device is almost
the same as FB7330, but only one ETH-Port and no USB.
Hardware
SoC: Lantiq Xway ARX188 PSB 50812 EL
RAM: 64MB DDR1 (Zentel A4S12D40FTP-G5)
Ethernet: Atheros 8030
Wireless: Atheros AR9227 b/g/n 2x2
DSL: Lantiq ADSL2+
DECT: Dialog SC14441
Buttons: WiFi, DECT
LEDs: Power/DSL, Fon, DECT, WLAN, Info
LEDs
Power: GPIO#44 (active low)
Internet: GPIO#47 (active low)
DECT: GPIO#38 (active low)
WLAN: GPIO#37 (active low)
Info: GPIO#35 (active low)
The Fon LED is labeled as internet in avm gpl sources.
Buttons
WLAN: GPIO#1 (active low)
DECT: GPIO#2 (active low)
Phy
GPIO#03: 25 MHz
GPIO#34: Reset (active low)
GPIO#39: Int
GPIO#42: MII MDIO
GPIO#43: MII MDC
PCIe
GPIO#21: reset (active low)
Installation:
To install OpenWrt via Eva bootloader, within the first seconds after
power on a ftp connection need to be established to the FRITZ!Box at
192.168.178.1 and the the following ftp commands need to be run:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put /path/to/openwrt-lantiq-xway-avm_fritz7312-squashfs-sysupgrade.bin mtd1
ftp> quote REBOOT
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
Use of_mdiobus_register() to pass the ethernet phy node to the phy
drivers. This is needed for the at8030 phy driver which needs to know
the GPIO which is connected to the ar8030 reset pin.
This driver expects a child in gsw/etop node named "mdio-bus", which has
the ethernet phys defined:
&gsw {
phy-mode = "rmii";
phy-handle = <&phy0>;
mtd-mac-address = <&ath9k_cal 0xa91>;
mtd-mac-address-increment = <(-2)>;
mdio-bus {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
phy0: ethernet-phy@0 {
reg = <0>;
reset-gpios = <&gpio 34 GPIO_ACTIVE_LOW>;
};
};
};
Fallback to mdiobus_register() if no mdio-bus child node exists. This
way we don't need to touch all xway dts files, for which we don't know
the actual address on the mdio bus.
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
The mac address for the 2.4 wireless need to be decremented by one.
Correct MAC adress increments for this board are:
wlan0 (5GHz) : -2
wlan1 (2.4GHz) : -1
eth1 (LAN) : 0
eth0 (WAN) : 1
Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
Drop the parallel-unsafe custom Build/dtb macro and use the .dtb artifacts
produced by the generic image build code.
Also remove unused .dtb references in the mt7623 subtarget.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
F9K1115v2 has a kernel partition size of 1408 kB.
Since kernel 4.9.x+ the kernel image for this device compiled had exceeded
the kernel partition size limit and thus failing size check.
The kernel image generated for this device
under ar71xx tiny target is 1329.67 kB < 1408 kB.
Signed-off-by: Kin Chan <kcchan1@outlook.com>
This patch adds support for the MikroTik RB931-2nD (hAP mini):
https://mikrotik.com/product/RB931-2nD
Specifications:
* SoC: Qualcomm QCA9533 (650MHz)
* RAM: 32MiB
* Storage: 16MiB SPI NOR flash
* Ethernet: 3x100M
* Wireless: QCA9533 built-in, dual-chain 802.11b/g/n
Installation:
1. Setup a DHCP/BOOTP Server with the following parameters:
* DHCP-Option 66 (TFTP server name): pointing to a local TFTP
server within the same subnet of the DHCP range
* DHCP-Option 67 (Bootfile-Name): matching the initramfs filename
of the to be booted image. The usable intramfs files are:
- openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
- openwrt-ar71xx-mikrotik-vmlinux-initramfs-lzma.elf
- openwrt-ar71xx-mikrotik-rb-nor-flash-16M-initramfs-kernel.bin
2. Press the reset button on the board and keep that pressed.
3. Connect the board to your local network via its Internet port.
4. Release the button after the LEDs on the board are turned off.
Now the board should load and start the initramfs image from
the TFTP server.
5. Now connect the board via either of its LAN ports (2 or 3).
6. Upload the sysupgrade image to the board with scp:
$ scp openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/fw.bin
7. Log in to the running system listening on 192.168.1.1 via ssh
as root (without password):
$ ssh root@192.168.1.1
8. Flash the uploaded firmware file from the ssh session via the
sysupgrade command:
root@OpenWrt:~# sysupgrade /tmp/fw.bin
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
SOC: BCM63168 (BMIPS4350 V8.0 @400MHz)
Flash size: 16 MiB
RAM size: 128 MiB
Heavily based on patch for OpenWRT Chaos Chalmer.
Original patch and more info can be found at:
https://openwrt.org/toh/sky/sr102
Known issues:
- Wireless and ADSL modem are not working.
Signed-off-by: Andrius Štikonas <andrius@stikonas.eu>
The original vendor's driver programmed the dma controller's
AHB HPROT values to enable bufferable, privileged mode. This
along with the "same priorty for both channels" could very
well fix the freezes that have been reported on the forum by
@ticerex and @takimata.
<https://forum.lede-project.org/t/wd-mybook-live-duo-two-disks/16195/46>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The code has some remaining issues that cause ethernet hangs, so
disable it for now until we can get it fixed
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Using the NAPI or netdev frag cache along with other drivers can lead to
32 KiB pages being held for a long time, despite only being used for
very few page fragment.
This can happen if the ethernet driver grabs one or two fragments for rx
ring refill, while other drivers use (and free up) the remaining
fragments. The 32 KiB higher-order page can only be freed once all users
have freed their fragments, which only happens after the rings of all
drivers holding the fragments have wrapped around.
Depending on the traffic patterns, this can waste a lot of memory and
look a lot like a memory leak
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The line that produces factory image was accidentally left by me while
testing before inital commit.
I came to the conclusion that flashing from OEM firmware does not work
(seems to share this behavior with other tplinks based on mt7628).
I have not done any further analysis, as I was unable to open the
case and attach a serial port (too much glue). Maybe i will try once
more.
So the way to do initial flashing (or un-bricking) is to use the
tftp-recover image. It is possible to revert to OEM firmware with tftp
recovery; in this case the first 512 bytes the image file need to be
cut off.
Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
[add explaination provided via mail as commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Extend the small_flash feature to disable swap, core dumps, and
kernel debug info, and change the squashfs block size to 1024KiB.
Also change squashfs fragment cache to 2 for small_flash to ease memory
usage.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
Add a new config option to allow to select the default compile
optimization level for the kernel.
Select the optimization for size by default if the small_flash feature is
set. Otherwise "Optimize for performance" is set.
Add the small_flash feature flag to all (sub)targets which had the
optimization for size in their default kernel config.
Remove CC_OPTIMIZE_FOR_* symbols from all kernel configs to apply the new
setting.
Exceptions to the above are:
- lantiq, where the optimization for size is only required for the
xway_legacy subtarget but was set for the whole target
- mediatek, ramips/mt7620 & ramips/mt76x8 where boards should have
plenty of space and an optimization for size doesn't make much sense
- rb532, which has 128MByte flash
Signed-off-by: Mathias Kresin <dev@kresin.me>
Move boards to the tiny subtarget which break the build if the kernel is
set to "Optimize for performance".
Signed-off-by: Mathias Kresin <dev@kresin.me>
In the latest version of u-boot (2018.05) there was a swith to
Hush shell for ARC AXS10x boards(arc770/archs38):
commit 9249d74781e1 ("ARC: AXS10x: Enable hush shell").
In Hush shell using "$()" to declare envitonment variables is forbidden,
instead of this "${}" need to be used.
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: John Crispin <john@phrozen.org>
The changed applied to BananaPi R2 in upstream commit c0b0d540db1a,
which was backported to 4.14 in 4.14.53, is also required for the U7623.
Without updating the memory node, the board refuses to boot.
Fixes: d0839e020d ("kernel: bump 4.14 to 4.14.53")
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
- remove misaligned custom buffer allocation in the NAND driver
- remove broken bounce buffer implementation for 16-byte align
Let the MTD core take care of both
Fixes messages like these:
[ 102.820541] Data buffer not 16 bytes aligned: 87daf08c
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Newer kernels have a patch that implements compatible functionality
directly. Adjust the attribute of our own patch in preparation for
dropping it later
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rereshed all patches
Reworked patches to match upstream:
335-v4.16-netfilter-nf_tables-add-single-table-list-for-all-fa.patch
Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Partition name is picked by a parser_trx_data_part_name(). It has to
get correct partition offset (taking care of bad blocks) to work
properly.
This fixes UBI support for devices that have kernel flashed on partition
with a bad block.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This commit adds support for the OCEDO Raccoon
SOC: Atheros AR9344
RAM: 128MB
FLASH: 16MiB
WLAN1: AR9344 2.4 GHz 802.11bgn 2x2
WLAN2: AR9382 5 GHz 802.11an 2x2
INPUT: RESET button
LED: Power, LAN, WiFi 2.4, WiFi 5
Serial: Header Next to Black metal shield
Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
The Serial setting is 115200-8-N-1.
NOTE: The U-Boot won't boot with the serial attached.
Boot the device without serial attached and attach it
after 3 seconds.
Tested and working:
- Ethernet
- 2.4 GHz WiFi
- 5 GHz WiFi
- TFTP boot from ramdisk image
- Installation via ramdisk image
- OpenWRT sysupgrade
- Buttons
- LEDs
Installation seems to be possible only through booting an OpenWRT
ramdisk image.
Hold down the reset button while powering on the device. It will load a
ramdisk image named 'raccoon-uImage-initramfs-lzma.bin' from 192.168.100.8.
Note: depending on the present software, the device might also try to
pull a file called 'raccoon-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.
Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.
Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with
> fw_setenv bootcmd run bootcmd_1
Afterwards you can reboot the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
CONFIG_USB_MTU3 is not visible for the mediatek target by default, but
only when CONFIG_USB_GADGET is set. This will config option will be
remove with when running "make kernel_oldconfig", move this option to
the generic config to prevent this.
This fixes the build of the mt7623 subtarget of the mediatek target.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Shrink the tiny kernel by moving all switch and ethernet phy drivers to
the generic kernel config instead of the target kernel config.
All boards in the tiny and nand target are either ar7240 or ar9331 based,
which don't support external xMII and therefore no external ethernet phy
can be connected. None of the boards uses a realtek switch either.
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
The Unifi AC-Mesh Pro has identical hardware to the Unifi AC-Pro except
USB support.
Furthermore for setting parameters like antenna gain it is helpful to
know the exact device variant.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
Add a template for safeloader images and include it instead of
overwriting variables defined in the common tp-link build commands.
Split the existing tp-link templates to proper implement the safeloader
template.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Drop the LOADER_TYPE variables in case no loader is used at all or move
the variable to devices which are using a loader.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the provided image build variables to point the kernel-bin build
command to the kernel we are interested in.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the LOADER_TYPE variable to specify that we need the elf preloader
and append the loader via the corresponding build recipe. It allows to
enable initramfs images again for mikrotik NAND images, which caused a
build error before.
Add the minor header only to the kernel of the sysupgrade images, as it
is only required for the bootloader to find the kernel on flash.
Signed-off-by: Mathias Kresin <dev@kresin.me>
I-O DATA WN-AX1167GR is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7621A.
Specification:
- MT7621A (2-Cores, 4-Threads)
- 64 MB of RAM (DDR2)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 2x LEDs, 4x keys (2x buttons, 1x slide switch)
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- baudrate: 115200 bps (U-Boot, OpenWrt)
Stock firmware:
In the stock firmware, WN-AX1167GR has two os images each composed of
Linux kernel and rootfs.
These images are stored in "Kernel" and "app" partition of the
following partitions, respectively.
(excerpt from dmesg):
MX25L12805D(c2 2018c220) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 10 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config "
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000060000 : "iNIC_rf"
0x000000060000-0x0000007e0000 : "Kernel"
0x000000800000-0x000000f80000 : "app"
0x000000f90000-0x000000fa0000 : "Key"
0x000000fa0000-0x000000fb0000 : "backup"
0x000000fb0000-0x000001000000 : "storage"
The flag for boot partition is stored in "Key" partition, and U-Boot
reads this and determines the partition to boot.
If the image that U-Boot first reads according to the flag is
"Bad Magic Number", U-Boot then tries to boot from the other image.
If the second image is correct, change the flag to the number
corresponding to that image and boot from that image.
(example):
## Booting image at bc800000 ...
Bad Magic Number,FFFFFFFF
Boot from KERNEL 1 !!
## Booting image at bc060000 ...
Image Name: MIPS OpenWrt Linux-4.14.50
Image Type: MIPS Linux kernel Image (lzma compressed)
Data Size: 1865917 Bytes = 1.8 MB
Load Address: 80001000
Entry Point: 80001000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
raspi_erase_write: offs:f90000, count:34
.
.
Done!
Starting kernel ...
Flash instruction using factory image:
1. Connect the computer to the LAN port of WN-AX1167GR
2. Connect power cable to WN-AX1167GR and turn on it
3. Access to "192.168.0.1" on the web browser and open firmware
update page ("ファームウェア")
4. Select the OpenWrt factory image and perform firmware update
5. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for WN-AX1167GR
6. Wait ~180 seconds to complete flasing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
USB storage support is however SCSI Disk block device support isn't
meaning that connected devices wont enumerate.
Enable CONFIG_BLK_DEV_SD by default to fix it.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
BusyBox's `tar` command does not support the `--directory` directive, which
is essentially `-C` in short-form option.
BusyBox's `tar` command supports `-C`.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
These options are handled by generic configuration
Targets that need these options should select KERNEL_DEVMEM
and/or KERNEL_DEVKMEM options on OpenWRT's config
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
The WDR4900v1 uses the P1040 SoC, so the device tree pulls in the
definition for the related P1010 SoC. However, the P1040 lacks the
CAAM/SEC4 hardware crypto accelerator which the P1010 device tree
defines. If left defined, this causes the CAAM drivers (if present) to
attempt to use the non-existent device, making various crypto-related
operations (e.g. macsec and ipsec) fail.
This commit overrides the incorrect dt node definition in the included
file.
See also:
- https://bugs.openwrt.org/index.php?do=details&task_id=1262
- https://community.nxp.com/thread/338432#comment-474107
Signed-off-by: Tim Small <tim@seoss.co.uk>
Add two patches submitted for upstream review that significantly improve
the dwc2 driver on openwrt from kernel stability and performance
perspectives.
Fixes: FS#1367
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
TP-Link Archer C7 v2 USB port LED and GPIO names are in incorrect order,
i.e. in order to match actual user visible labels, usb1 should be usb2,
and vice versa.
This patch swaps LED and GPIO power control node names.
Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
Due do a missing KCONFIG isn't selectable nor enabled in the target
kernel config. Drop it for now and enable/add the driver at the time it
is required.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Netgear R7800 switch LAN ports are numbered backwards in LuCI,
i.e. numbering is not corresponding to the actual physical port labels,
patch fixes that.
Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
[merged with existing board using the same config]
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Specification:
- System-On-Chip: MediaTek MT7628NN
- CPU/Speed: 580 MHz
- Flash-Chip: ELM Technology GD25Q64
- Flash size: 8192 KiB
- RAM: 64 MiB
- Wireless No1: SoC-integrated: MT7628N 2.4GHz 802.11bgn
Currently the only method to install openwrt for the first time is via
TFTP recovery. After first install you can use regular updates.
Flash instructions:
1) To flash the recovery image, start a TFTP server with IP address
192.168.0.66 and serve the recovery image named tp_recovery.bin.
2) Connect your device to the LAN port, then press the WPS and Reset
button and power it up. Keep pressing the WPS/Reset button for
10 seconds or until the lock LED is lighting up.
It will try to download the recovery image and flash it.
It can take up to 2-3 minutes to finish. When it reaches 100%, the
router will reboot itself.
Signed-off-by: Romain MARIADASSOU <roms2000@free.fr>
Specification:
- System-On-Chip: MT7628N/N
- CPU/Speed: 580 MHz
- Flash-Chip: Winbond w25q256
- Flash size: 32768 KiB
- RAM: 128 MiB
- 5x 10/100 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (57600 8n1)
- Wireless No1 (2T2R): SoC-integrated: MT7628N 2.4GHz 802.11bgn
- Wireless No2 (2T2R): On-board chip: MT7612EN 5GHz 802.11ac
- USB: Yes 1 x 2.0
- 4x LED, 3x button
The device supports dual boot mode. So we use only first half of flash.
Flash instruction:
The only way to flash OpenWrt image is to use
tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-zyxel_keenetic-extra-ii-squashfs-factory.bin"
to "kextra2_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
This commit adds support for the MikroTik RouterBOARD RBM11g.
=Hardware=
The RBM11g is a mt7621 based device featuring one GbE port and one
miniPCIe slot with a sim card socket and USB 2.0.
==Switch==
The single onboard Ethernet port is connected the CPU directly.
The internal switch of the mt7621 SoC is disabled.
==Flash==
The device has one spi nor flash chip. It is a 128 Mbit winbond 25Q128FVS
connected to CS0.
==PCIe==
The board features a single miniPCIe slot. It has a dedicated mini SIM
socket and a USB 2.0 port. Power to the miniPCIe slot is controlled via
GPIO9.
==USB==
There are no external USB ports.
==Power==
The board can accept both, passive PoE and external power via a 2.1 mm
barrel jack (center-positive). The input voltage range is 11-32 V.
==Serial port==
The device does have an onboard UART on an unpopulated header next to the
flash chip:
GND: pin 2
TX: pin 7
RX: pin 6
Settings: 115200, 8N1
See below illustration for positioning of the header.
0 = screw hole
* = some pin
T = TX pin
R = RX pin
G = GND pin
Pinout:
+---------------
|O
| __
| / \
| \__/
|
|
|
| +---+
| |RAM|
| +--+ | |
| |**| <- unpopulated header with UART
| |*T| +---+
| |R*| +--------+
| |**| | |
| |G*| | CPU |
| +--+ | |
| +--+ | |
| | | +--------+
| +--+ <- flash chip
|O
| +-----+
| | |
|+--+ | |
|| | | |
+---------------------
=Installation=
To install an OpenWRT image to the device two components must be built:
1. A openwrt initramfs image
2. A openwrt sysupgrade image
===initramfs & sysupgrade image===
Select target devices "Mikrotik RBM11G" in
openwrt menuconfig and build the images. This will create the images
"openwrt-ramips-mt7621-mikrotik_rbm11g-initramfs-kernel.bin" and
"openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin" in the
output directory.
==Installing==
**Make sure to back up your RouterOS license in case you do ever want to
go back to RouterOS using "/system license output" and back up the
created license file.**
When rebooted the board will try booting via ethernet first. If your
board does not boot via ethernet automatically you will have to attach
to the serial port and set ethernet as boot device within RouterBOOT.
1. Set up a dhcp server that points the bootfile to tftp server serving
the "openwrt-ramips-mt7621-mikrotik_rbm11g-initramfs-kernel.bin"
initramfs image
2. Connect to ethernet port on board
3. Power on the board
4. Wait for OpenWrt to boot
Right now OpenWrt will be running with a SSH server listening. Now
OpenWrt must be flashed to the devices flash:
1. Copy "openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin"
to the device using scp.
2. Write openwrt to flash using "sysupgrade
openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin"
Once the flashing completes the board will reboot. Disconnect from the
devices ethernet port or stop the DHCP/TFTP server to prevent the device
from booting via ethernet again.
The device should now boot straight to OpenWrt.
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
Increase the available flash memory size in AVM Fritz!Box 3370 by
incorporating the unused extra partitions located after the ubi partition.
Note that users upgrading from a previous OpenWRT version need to
re-install from the boot loader to pick up the new partition layout.
Available flash space for rootfs+overlay increases from 48MB to 124MB.
Reverting to the OEM firmware is still possible (via the recovery utility
provided by AVM) as the OEM firmware appears to reformat the config and
nand-filesystem partitions upon first boot if necessary. The
reserved-kernel and reserved-filesystem partitions are overwritten by the
OEM firmware when installing an update, so their contents do not matter.
Boot loader and device-specific information (MAC addresses, calibration
data, etc.) are not located in NAND flash and remain unharmed by this
changed.
Tested with OEM firmware 06.54 on device with HWRevision 5 and Micron
flash chip.
Signed-off-by: Michael Kuron <m.kuron@gmx.de>
To keep the status of a LED connected to the stp during boot, the get
callback is required. If the callback is missing and the LED default
state is set to keep in the devicetree, the gpio led driver errors out
during load.
Fixes: FS#1620
Signed-off-by: Mathias Kresin <dev@kresin.me>
Don't mask bit 4 of the AT8022 phy id. If bit 4 of the AT8022 phy id
(0x004dd023) is masked, it will match the phy id of the AR8327 switch
(0x004dd033) as well.
It results in applied at803x driver settings/callbacks, which will at
least limit the AR8327 phys to 100MBit operation instead of the possible
1000MBit.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Backport hot off the press upstream netlink patch. Fixes stats display
from CAKE qdisc on MIPS allowing us to bump CAKE to latest version.
The gen_stats facility will add a header for the toplevel nlattr of type
TCA_STATS2 that contains all stats added by qdisc callbacks. A reference
to this header is stored in the gnet_dump struct, and when all the
per-qdisc callbacks have finished adding their stats, the length of the
containing header will be adjusted to the right value.
However, on architectures that need padding (i.e., that don't set
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS), the padding nlattr is added
before the stats, which means that the stored pointer will point to the
padding, and so when the header is fixed up, the result is just a very
big padding nlattr. Because most qdiscs also supply the legacy TCA_STATS
struct, this problem has been mostly invisible, but we exposed it with
the netlink attribute-based statistics in CAKE.
Fix the issue by fixing up the stored pointer if it points to a padding
nlattr.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
In some cases, recent builds fail to boot from flash with at least some
MT7621 based devices. The error message is:
"LZMA ERROR 1 - must RESET board to recover"
Booting the same kernel via TFTP works for some reason.
Through testing I figured out that limiting the LZMA dictionary size
seems to prevent these errors
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This patch ports the TP-Link TL-WR741ND v4 and TL-WR740ND v4 to the
ath79 target.
Because the two devices share the same hw layout, this patch adds a common
.dtsi which is included by the two .dts.
Signed-off-by: Rocco Folino <rocco@folino.io>
The order of the Ethernet ports were mixed up.
This commit fixes the order to be aligned with the physical layout.
Signed-off-by: Lev <leventelist@gmail.com>
The Unifi AC Mesh is equivalent to the Unifi AC Lite. However,
for setting certain parameters with the flashed device it is
helpful that the devices know their variant (e.g. automatically
setting antenna gain for the different antennas in Lite and Mesh).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- fix sysupgrade check
- move usb to v4 dts because v5 doesn't have it
- make wan mac address behave like ar71xx target
- add orange wan led support, it can be userspace activated like:
on:
echo default-on > /sys/class/leds/tp-link\:orange\:wan/trigger
off:
echo none > /sys/class/leds/tp-link\:orange\:wan/trigger
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
