reorder some parts of the patch to remove the declaration-after-
statement warning.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46205
Current firmware should work for station mode as well, and the older
firmware will usually behave worse and become unsupported over time.
Also, the MAC address handling on ar71xx is only implemented on one
firmware version.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46197
This firmware adds support for management frames over normal
packet transport interface instead of over the WMI management
interface.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46195
A long time ago, ath9k had issues during reset where the DMA engine
would stay active and could potentially corrupt memory.
To debug those issues, the driver would print warnings whenever they
occur.
Nowadays, these issues are gone and the primary cause of these messages
is if the MAC is stuck during reset or busy processing a long
transmission. This is fairly harmless, yet these messages continue to
worry users.
To reduce the number of bogus bug reports, turn these messages into
debug messages and count their occurence in the "reset" debugfs file.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46158
A duplicate include guard prevents inclusion of barrier.h in UML build and this prevents mac80211 from building.
This patch re-enables mac80211 hwsim and renames the include guard.
See https://lists.openwrt.org/pipermail/openwrt-devel/2015-June/033614.html for details.
Signed-off-by: Martin Tippmann <martin.tippmann@gmail.com>
Signed-off-by: Nicolas Thill <nico@openwrt.org>
SVN-Revision: 46133
There are two important patches in this patchset: updating read pointer
quicker & rework of .get_station().
There are few more upstream patches that are p2p-related and weren't
backported in this commit.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46084
This allows e.g. BCM43602 to work out of box, without dumping a proper
MTD partition to /lib/firmware/ NVRAM file.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45931
Before starting hostapd we create interface for it. The problem is we
try to create STA interface just to let hostapd change it to AP later.
It may fail if device doesn't support STA interfaces or if we already
hit a limit. Consider following phy (it's from BCM43602 and brcmfmac):
$ iw phy phy0 info | tail
valid interface combinations:
* #{ IBSS, managed } <= 1, #{ AP } <= 4, #{ P2P-client, P2P-GO } <= 1, #{ P2P-device } <= 1,
total <= 3, #channels <= 1
Trying to setup 2 interfaces: STA + AP results in:
radio0 (1101): command failed: Operation not supported (-95)
radio0 (1101): command failed: Operation not supported (-95)
radio0 (1101): command failed: Operation not supported (-95)
radio0 (1101): command failed: Operation not supported (-95)
radio0 (1101): Configuration file: /var/run/hostapd-phy0.conf
radio0 (1101): Could not read interface wlan0-1 flags: No such device
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45856
This fixes various problems with parsing platform NVRAM. It's required
to get BCM43602 working in most cases.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45802
3.18.12 backported 61ada528dea028331e99e8ceaed87c683ad25de2 ("sched/wait:
Provide infrastructure to deal with nested blocking") from 3.19, causing
the following error on load:
[ 13.588000] compat: exports duplicate symbol woken_wake_function (owned by kernel)
Fix this by guarding it with a check for 3.18.11 or earlier instead of
3.19.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45710
instead of failing when authsae is not installed, also try using
wpa_supplicant as the newly added -mesh variants support mesh mode
and SAE encryption.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 45520
Two errors "netifd: radio0: sh: bad number" have recently surfaced in system
log in trunk when wifi interfaces come up. I tracked the errors to checking
numerical values of some config options without ensuring that the option has
any value.
The errors I see have apparently been introduced by r45051 (ieee80211r in
hostapd) and r45326 (start_disabled in mac80211). My patches fix two
instances of "bad number", but there may be a third one, as the original
report in bug 19345 pre-dates r45326 and already has two "bad number" errors
for radio0.
https://dev.openwrt.org/ticket/19345
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 45379
Subtarget legacy is supposed to support all ssb SoC except for BCM4705.
There are few BCM4703 devices with 802.11n supprt (WRT160N v1.0, v1.1).
Few BCM4704 devices with 802.11n: ASUS WL-500W, Linksys WRT150N v1.0 &
v1.1, Linksys WRT300N v1.0, Netgear WNDR3300 v1, WNR834B v1 & v2.
It seems we have to enable N-PHY for legacy as well to support above.
Unfortunately it increases root.squashfs size by 48 460 B.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45309
Most AP devices out there do not have a properly programmed regulatory
domain code, which means they are limited to US frequencies by default.
This has been a major annoyance for a long time now. Since no fix for
the manfuacturing process seems to be forthcoming, the only sane option
seems to be to allow users to change the country code in such cases.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45252
This backports upstream commit 702131e2a393b45174be326f1dbe20b658b4f157
bcma: move PCI IRQ control function to host specific code
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44969
Based on patch by Bryan Forbes <bryan@reigndropsfall.net>
Also update mt76 to update for API changes
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44655
This patch adds SDIO support for the brcmfmac driver.
For now only very few boards need it.
Signed off by: José Vázquez Fernández <ppvazquezfer@gmail.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44465
Instead of hardcoding /bin/bash, use /usr/bin/env bash - this fixes the
build on FreeBSD 10.1.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44283
Part of rev 44173 added setting the SM Power Save capability in the hostapd.conf
file if the driver indicated that it was supported. It appears this was
incorrect, because the field in the actual HT Capabilities field in the AP
configuration is really a state indication. Just copying the state from the
capability resulted in the AP indicating that it had SMPS enabled all the time
if it supported SMPS. This effectively just disables all clients from sending
packets to the AP with more than one spatial stream, for no good reason.
So remove this part of the change.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
SVN-Revision: 44239
This "patch to the patch" fixes a NULL pointer derefence crash in the new
intermediate software queues. The crash can be reproduced by injecting an
802.11 frame with a BSSID that does not belong to a configured vif. The
wperf tool (https://github.com/anyfi/wperf) may be convenient for doing
this.
Signed-off-by: Johan Almbladh <ja@anyfi.net>
SVN-Revision: 44220
Update the libertas driver to configure symlinks in sysfs. This enables
the driver to be handled correctly by the mac80211/netifd/hostapd scripts.
With this patch, the wireless interface is functional on Guruplug Server Plus.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 44174
Add some missing 802.11n capabilities to the hostapd ht_capab string when
supported by the hardware: Spatial Multiplexing Power-Save and 7935-byte AMSDUs.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
SVN-Revision: 44173
If '/sys/class/ieee80211/phyN' is not a symlink, the call to readlink
produces either an empty path (if /sys/class/ieee80211/phyN/device doesn't
exist) or a path that begins with '/sys/class/ieee80211' (which does not
work with the subsequent line to strip '/sys/devices' from the beginning of
the path). Modify the checks to detect these conditions, and fallback to
using the macaddr.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 44172
Change the name of the package to match the module name so it matches the
package name referenced by the Kirkwood (Guruplug) profile.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 44171
Target pxcab and ps3 were removed from maintaince in r34764 and r34765
respectively.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 43850
This patch added stuff that is already there and if it would be needed
this would result in a compile error.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43131
[base-files] shell-scripting: fix wrong usage of '==' operator
normally the '==' is used for invoking a regex parser and is a bashism.
all of the fixes just want to compare a string. the used busybox-ash
will silently "ignore" this mistake, but make it portable/clean at least.
this patch does not change the behavior/logic of the scripts.
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 42911
The DFS pattern detector now supports all three regions; ETSI, FCC and
JP, so there is no reason to not have it enabled anymore.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42431
Fixes
b43-phy0 ERROR: Firmware file "b43-open/ucode30_mimo.fw" not found
for BCM43217 devices.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41943
This add 5GHz support for N-PHY to b43, thanks Rafał Miłecki.
b43_wflush16 was put into an extra function because it is pretty big in asm.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41900
This change introduces support for wildcard patterns in "option path"
of section "wifi-device".
Objective is to allow paths like "*/usb[0-9]/*/*" in order to claim
any usb device using the same backend type, regardless of its bus
address or phy name.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 41873
With this patch mac80211 will be rebuild when one of these config
options was changed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41677
I missed adding B43_PHY_G to .local-symbols, without this it will not
be added to autoconf.h
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41676
The vif option dtim_period was accidently renamed dtim_interval in r38988
("netifd: add wireless configuration support and port mac80211 to the new
framework"). This is wrong and makes the dtim_period/dtim_interval a dead
option because the rest of the config generation code still uses dtim_period.
Reported-by: Jeppe Ledet-Pedersen <jlp@steinwurf.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
SVN-Revision: 41557
This updates linux-firmware to version
7f388b4885cf64d6b7833612052d20d4197af96f from 2014-06-04.
In addition it adds new firmware for Intel, Broadcom and Realtek devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41523
r40682 ("mac80211: clean up ht capability handling, drop the use of the
ht_capab list, use individual variables instead") removed the ht_capab list and
replaced it with optional variables to disable features for a phy. But these
variables weren't added in drv_mac80211_init_device_config and thus didn't make
any difference when modifying /etc/config/wireless.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
SVN-Revision: 41180
This patch enables netifd to query 802.11ac-driver for the maximum
supported A-MPDU length exponent, possibly increasing VHT throughput by
more aggressive frame aggregation.
v2: refreshed patch
Signed-off-by: Matti Laakso <malaakso at elisanet.fi>
SVN-Revision: 40938
