Commit graph

979 commits

Author SHA1 Message Date
Jonas Gorski
7d6cff4882 kernel: update 3.18 to 3.18.21
Changelog:
 * https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.21

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46768
2015-09-02 10:18:15 +00:00
Jonas Gorski
09609b4e44 brcm63xx: disable the openwrt commandline hack
We don't make use of it, so no need to have it enabled.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46757
2015-08-30 12:18:00 +00:00
Jonas Gorski
5ebd02e8d5 brcm63xx: remove legacy led/button related patches
We register all gpio buttons and leds through DT, so no need to keep
fixes/additions for the platform data based bay.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46753
2015-08-30 12:17:52 +00:00
Jonas Gorski
78f253f9b1 brcm63xx: add Comtrend VR-3026e support
Add support for Comtrend VR-3026e v1.
The device is almost identical to the Comtrend VR-3025un.

Signed-off-by: Martin Tesar <tesarmar@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46752
2015-08-30 12:17:46 +00:00
Jonas Gorski
05a3cdd71f brcm63xx: fix WAP-5813n default network config
/etc/uci-defaults/02_network had a typo, making it generate the wrong
network config.

Closes #20407.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46727
2015-08-26 13:03:09 +00:00
Jonas Gorski
77a70a0716 brcm63xx: enable dual rx/tx spi support for hsspi
should improve flash access times. Should be harmless to gnerally
enable regardless if a flash supporting dual reads is attached. In
doubt, spi-nor will just fall back to serial reads.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46725
2015-08-25 22:04:53 +00:00
Jonas Gorski
2d379e796f kernel: update 4.1 to 4.1.6
Changelog:
* https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.6

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46713
2015-08-23 18:06:11 +00:00
Jonas Gorski
ecdce239a5 brcm63xx: ensure dummy byte is set for mapped spi flash with fast read
Some CFEs seem to misconfigure the mapped memory flash access with
fast read but without a dummy byte, causing all accesses to be prefixed
with 0xff.
This of course breaks reading out the nvram, so do not just move back to
single i/o accessors, but also ensure that the dummy byte is correctly
set.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46707
2015-08-23 09:35:56 +00:00
Jonas Gorski
4e81a1473e brcm63xx: move gzip build command to include/image.mk
Allow other targets to make use of it.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46601
2015-08-14 15:10:47 +00:00
Jonas Gorski
6be2305da8 kernel: update 4.1 to 4.1.5
Changelog:
 * https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.5

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46598
2015-08-14 13:06:33 +00:00
Jonas Gorski
8e69c9f7ef image.mk: store the device name variable
Make the device name accessible for any build commands instead of
forcing targets to define it themselves.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46597
2015-08-14 13:05:22 +00:00
Jonas Gorski
4ecae78c16 image.mk: replace all Build/netgear-chk with a generic implementation
Instead of letting each target define it themselves, create on in
include/image.mk and let the targets use it.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46596
2015-08-14 13:05:14 +00:00
Jonas Gorski
79b733264b brcm63xx: prefix netgear specific device variables with NETGEAR_
Rename BOARD_ID to NETGEAR_BOARD_ID.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46595
2015-08-14 13:04:43 +00:00
Hauke Mehrtens
0b8643af4f kernel: update 3.18 to 3.18.20
Changelog:
 * https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.20

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 46570
2015-08-09 11:09:52 +00:00
Jonas Gorski
3368b4799b brcm63xx: fix crash on 6358/6368 when booting from thread 1
It looks like RAC flushes cause random corruption(?) when the
second thread is set as default.

Fixes #20160.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46563
2015-08-05 13:55:42 +00:00
Jonas Gorski
a105688c87 brcm63xx: Add support for Plusnet 2704N
BCM6318: add support for Plusnet / Sagem 2704N (V1)
Signed-off-by: Matt Goring <matt.goring@googlemail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46562
2015-08-05 13:55:37 +00:00
Jonas Gorski
65654a3c54 brcm63xx: build image for DSL-275XB D1
It boots fine, so no reason to not build it.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46561
2015-08-05 13:55:18 +00:00
Jonas Gorski
ef78a63997 brcm63xx: switch to new image building system
Switches BCM63xx to the new IB system.
Images are generated per device definitions.
There are no changes in the produced images except for some name changes,
caused by the new IB system.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46490
2015-07-25 12:12:11 +00:00
Jonas Gorski
5a62d503d9 brcm63xx: use new tool for generating redboot images
Simplify image/Makefile by using the new perl script for RedBoot.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46489
2015-07-25 12:12:06 +00:00
Jonas Gorski
4981c7da0d brcm63xx: make use of dt-includes
Now that we have a dtc command that invokes the preprocessor, make use
of it and replace the magic numbers with KEY_* defines.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46391
2015-07-16 11:15:02 +00:00
Jonas Gorski
71e0bd0165 brcm63xx: make use of the new BuildDTB command
Now that we have a BuildDTB command, make use of it instead of calling
dtc directly.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46390
2015-07-16 11:13:47 +00:00
Jonas Gorski
491cfb06d0 brcm63xx: HG553 buttons support
This patch adds buttons support for Huawei EchoLife HG553.

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46388
2015-07-16 11:12:41 +00:00
Jonas Gorski
730f06410e brcm63xx: switch to 4.1
Switch brcm63xx to 4.1 to give it some initial testing, but keep 3.18
at least until CC-final is out.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46386
2015-07-15 14:42:04 +00:00
John Crispin
096b3759a9 build: Prevent more gzip timestamps
To improve reproducibility, prevent the inclusion of timestamps
in the gzip header.

Signed-off-by: Reiner Herrmann <reiner@reiner-h.de>

SVN-Revision: 46361
2015-07-14 09:57:45 +00:00
Jonas Gorski
1e8c3d2769 brcm63xx: use IRQCHIP_DECLARE instead of self-baked version
Backport a commit from 4.2 making IRQCHIP_DECLARE available outside of
drivers/irqchip and use it.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46183
2015-07-05 21:31:52 +00:00
Jonas Gorski
761fc3f035 brcm63xx: 4.1: switch to upstream UHI interface
Replace the appended dtb patch with the upstream accepted version and
update the code to work with the changed interface.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46181
2015-07-05 11:28:46 +00:00
Jonas Gorski
ad80d3869d brcm63xx: swap a4001n power leds again
This partially reverts r44577 ("brcm63xx: fix DTS LEDs and buttons").

Fixes #19858.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46149
2015-06-30 23:26:05 +00:00
Jonas Gorski
3a9e4ba896 brcm63xx: unbreak board_probe_switch again
Also move it to an earlier place so new boards added are less likely
to confuse quilt.

Fixes #19965.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46148
2015-06-30 23:26:02 +00:00
Jonas Gorski
bd398e1765 brcm63xx: add kernel 4.1 support
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46113
2015-06-22 12:28:46 +00:00
Jonas Gorski
9a59b350b7 kernel: update 3.18 to 3.18.16
Changelogs:

* https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.15
* https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.16

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46011
2015-06-17 09:54:55 +00:00
Jonas Gorski
84bfed7bd3 brcm63xx: fix A4001N image padding size
When r42245 moved A4001N to DT based detection the image padding size
was accidentally increased from 4 to 8 MiB. This made images unflashable
on these devices.

Fixes #19836.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45945
2015-06-11 12:10:43 +00:00
Jonas Gorski
6d07290de3 brcm63xx: fix livebox image generation
Livebox does need the uncompressed kernel, so just create it during
image generation.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45875
2015-06-02 10:23:45 +00:00
Jonas Gorski
9c6945d7a1 brcm63xx: delete uncompressed kernels after use
Delete the dtb appended, uncompressed kernels after having compressed
them, so they don't end in the image builder.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45869
2015-06-01 12:37:34 +00:00
Jo-Philipp Wich
957534693c brcm63xx: use common image prefix
Also remove "redbootscript" and "redbootscript.padded" junk files.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
Acked-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45780
2015-05-27 15:18:21 +00:00
Jonas Gorski
76d079204d kernel: update 3.18 to 3.18.14
Changelogs:

* https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.12
* https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.13
* https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.14

Build tested on brcm63xx and ipq806x, runtested on brcm63xx.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45711
2015-05-21 19:32:46 +00:00
Jonas Gorski
4bb7b2186e brcm63xx: fix failsafe lan and status led for DSL-274xB rev. F1
Add it to the appropriate places so the power led properly works
and ethernet is properly configured for failsafe.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45709
2015-05-21 19:32:00 +00:00
Jonas Gorski
509c3211d6 brcm63xx: Add Huawei HG655b support
This patch adds support for the Huawei HG655b.

Nothing much special in this router, it's just another BCM6368 with
a Ralink RT3062 wifi chip and the calibration data embedded in the
main flash chip at offset 0x7c0000. There is also configuration data
used by the OEM firmware before the cal_data partition, this area is
protected by the board_data partition in this patch.

Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45708
2015-05-21 19:31:54 +00:00
Jonas Gorski
9feb1361c4 brcm63xx: fix bcm6348 ext irqc compatible name
This was a remnant of an old version.

Reported-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45583
2015-04-27 11:06:05 +00:00
Jonas Gorski
5e7f4ab632 brcm63xx: fix bcm3368.dtsi typo.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45582
2015-04-27 11:06:00 +00:00
Jonas Gorski
16127b3429 brcm63xx: fix leds bcm963269bhr
Fix the led naming and gpios.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45558
2015-04-21 17:00:39 +00:00
Jonas Gorski
5e8eedb897 brcm63xx: add missing bcm96329bhr profile and dts
Hopefully the last missing board.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45557
2015-04-21 16:43:46 +00:00
Jonas Gorski
681eb8c3de brcm63xx: fix bcm63268 rgmii port rgmii configuration
This should rather be done by passing appropriate platform_data/OF, but
should suffice for now.

Fixes e.g. GbE ports on BCM963268BU_P300.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45505
2015-04-19 11:38:42 +00:00
Jonas Gorski
440124dcbb brcm63xx: allow using all four rgmii ports on bcm6316x
At least the third rgmii port is available on 63169, so assume all are
available. Simplifies cpu vs. variant handling.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45504
2015-04-19 11:38:24 +00:00
Jonas Gorski
c1ea714d43 brcm63xx: BCM963268BU_P300 reference board fixes
- Fix profile name.
- Rremove whitespace on board patch.
- Refresh patches.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45499
2015-04-18 22:33:50 +00:00
Jonas Gorski
6232e845da brcm63xx: fix bcm96318ref_p300 profile name
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45486
2015-04-18 09:34:17 +00:00
Felix Fietkau
e8126cbfbd kernel: remove kernel module checks/dependencies for 3.14
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45377
2015-04-11 10:43:46 +00:00
Jonas Gorski
a709beb4ae brcm63xx: fix zyxel kernel name
Accidentally left over development artifact.

Reported-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45179
2015-03-31 09:54:15 +00:00
Jonas Gorski
a54b8303d2 brcm63xx: don't build non-dtb kernels anymore
Now that all supported boards have an dts there is no need for a
dtb free kernel anymore.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45169
2015-03-30 20:21:24 +00:00
Jonas Gorski
0f08442ded brcm63xx: move DSL-275XB to DT
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45168
2015-03-30 20:21:15 +00:00
Jonas Gorski
f77b446051 brcm63xx: move bcm6318 reference boards to DT
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45167
2015-03-30 20:21:07 +00:00