NXP Layerscape LSDK had set up its own open source web site
and github for release.
https://lsdk.github.iohttps://github.com/qoriq-open-source
This patch is to update rcw/fman_ucode/u-boot packages with LSDK
git trees. Also add some patches of packages to support LEDE.
Since ARMv8 32-bit u-boot images are same with ARMv8 64-bit images
but 64-bit toolchain couldn't be used for 32-bit targets, we still
use a private tree for ARMv8 32-bit u-boot images. This is in plan
to move this private tree to NXP Layerscape github.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Do not put the u-boot and ucode images into the kernel build directory as this
directory might get removed after kernel updates while the u-boot packages
InstallDev recipe is not getting re-executed because it is still considered
current, leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add support for NXP layerscape ls1046ardb 64b/32b Dev board.
LS1046ARDB Specification:
-------------------------
Memory subsystem:
* 8GByte DDR4 SDRAM (64bit bus)
* 512 Mbyte NAND flash
* Two 64 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
* On-board 4G eMMC
Ethernet:
* Two XFI 10G ports
* Two SGMII ports
* Two RGMII ports
PCIe:
* PCIe1 (SerDes2 Lane0) to miniPCIe slot
* PCIe2 (SerDes2 Lane1) to x2 PCIe slot
* PCIe3 (SerDes2 Lane2) to x4 PCIe slot
* USB 3.0: one super speed USB 3.0 type A port, one Micro-AB port
* UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
The QorIQ LS1012A processor, optimized for battery-backed or
USB-powered, integrates a single ARM Cortex-A53 core with a hardware
packet forwarding engine and high-speed interfaces to deliver
line-rate networking performance.
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
LEDE/OPENWRT will auto strip executable program file while make. So we
need select CONFIG_NO_STRIP=y while make menuconfig to avoid the ppfe network
fiemware be destroyed, then run make to build ls1012ardb firmware.
The fsl-quadspi flash with jffs2 fs is unstable and arise some failed message.
This issue have noticed the IP owner for investigate, hope he can solve it
earlier. So the ls1012ardb now also provide a xx-firmware.ext4.bin as default
firmware, and the uboot bootcmd will run wrtboot_ext4rfs for "rootfstype=ext4"
bootargs.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
Add support for NXP layerscape ls1043ardb 64b/32b Dev board.
LS1043a is an SoC with 4x64-bit up to 1.6 GHz ARMv8 A53 cores.
ls1043ardb support features as: 2GB DDR4, 128MB NOR/512MB NAND, USB3.0, eSDHC,
I2C, GPIO, PCIe/Mini-PCIe, 6x1G/1x10G network port, etc.
64b/32b ls1043ardb target is using 4.4 kernel, and rcw/u-boot/fman images from
NXP QorIQ SDK release.
All of 4.4 kernel patches porting from SDK release or upstream.
QorIQ SDK ISOs can be downloaded from this location:
http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
