Commit graph

16 commits

Author SHA1 Message Date
Michael Gray
bfbdeeb3de mvebu: add support for WRT32X (venom)
Linksys WRT32X (Venom) is identical in hardware to the WRT3200ACM
with a different flash layout and boots zImage rather than uImage.

Specification:
- Marvell Armada 385 88F6820 (2x 1.8GHz)
- 256MB of Flash
- 512MB of RAM
- 2.4GHz (bgn) and 5GHz (an+ac wave 2)
- 4x 1Gbps LAN + 1x 1Gbps WAN
- 1x USB 3.0 and 1x USB 2.0/eSATA (combo port)

Flash instruction:
Apply factory image via web-gui.

Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
2018-05-14 17:20:10 +02:00
Stijn Tintel
ec1d7b9461 kernel: bump 4.14 to 4.14.34
Refresh patches.
Update patches that no longer apply:
- backport/313-netfilter-remove-defensive-check-on-malformed-packet.patch
- pending/642-net-8021q-support-hardware-flow-table-offload.patch

Compile-tested: x86/64.
Runtime-tested: x86/64.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-04-16 00:22:57 +03:00
Hauke Mehrtens
a74fd570a2 kernel: update kernel 4.14 to 4.14.32
The following patches are now included upstream:
* 0052-MIPS-lantiq-fix-usb-clocks.patch
* 0053-MIPS-lantiq-enable-AHB-Bus-for-USB.patch
* 0060-lantiq-ase-enable-MFD-SYSCON.patch

Closes: FS#1466

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-04-03 23:26:45 +02:00
Imre Kaloz
4b486e32fb mvebu: Add support for WRT3200ACM with new NAND flash
Newer Linksys boards might come with a Winbond W29N02GV which can be
configured in different ways. Make sure we configure it the same way as
the older chips so everything keeps working.

Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
2018-03-31 16:12:39 +02:00
Felix Fietkau
5faa9556b1 mvebu: disable cpu idle on WRT1900ACv1
A regression seriously affecting the Linksys WRT1900ACv1 (Mamba) was
introduced some time between the OpenWrt/LEDE v4.4 and v4.9 kernels.
The root cause has not yet been identified, despite many attempts for
more than a year. Disabling the SoC specific CPU idle support should
mitigate this issue.

The symptoms on an affected system are unwanted reboots at a variable
frequency. In many cases almost immediately after boot, causing a
bootloop.  This effectively disables support for Mamba on OpenWrt
with kernels > v4.4.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-03-19 23:28:49 +01:00
Hauke Mehrtens
8605ac87f8 mvebu: Disable internal RTC on Linksys devices
The internal RTC does not work correctly on these Linksys boards based
on Marvell SoCs. It is off by 3 minutes in 10 minutes running, this
was reported by multiple users. On the Linksys Mamba device the device
tree comment says that no crystal is connected to the internal RTC, this
is probably also true for the other devices.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-17 22:59:29 +01:00
Rosen Penev
dfe4de0287 mvebu: Add Solidrun RTC init patch.
Some boards like the Turris Omnia have an RTC chip that does not get
initialized. Initializing the RTC at the driver level helps get rid of
bootloader hacks that write special register values.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-03-17 22:59:29 +01:00
Rosen Penev
31717ec0ff mvebu: Backport RTC trimming support.
This enables a higher precision mode for the RTC.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-03-17 22:59:29 +01:00
Hauke Mehrtens
bf4aa52dbf kernel: make mtd patches apply again
This makes some of the mtd patches apply again after some generic
patches were changed.
These problems where found by build bot.

Fixes: ac9bcefa3b ("kernel: use V10 of mtd patchset adding support for "compatible" string")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-15 00:42:41 +01:00
Tomasz Maciej Nowak
584d7c53bd mvebu: new subtarget cortex A53
This commit introduces new subtarget for Marvell EBU Armada Cortex A53
processor based devices.

The first device is Globalscale ESPRESSObin. Some hardware specs:

SoC: Marvell Armada 3700LP (88F3720) dual core ARM Cortex A53
     processor up to 1.2GHz
RAM: 512MB, 1GB or 2GB DDR3
Storage: SATA interface
         µSD card slot with footprint for an optional 4GB EMMC
         4MB SPI NOR flash for bootloader
Ethernet: Topaz Networking Switch (88E6341) with 3x GbE ports
Connectors: USB 3.0
            USB 2.0
            µUSB port connected to PL2303SA (USB to serial bridge
            controller) for UART access
Expansion: 2x 46-pin GPIO headers for accessories and shields with
           I2C, GPIOs, PWM, UART, SPI, MMC, etc
           MiniPCIe slot
Misc: Reset button, JTAG interface

Currently booting only from µSD card is supported.
The boards depending on date of dispatch can come with various U-Boot
versions. For the newest version 2017.03-armada-17.10 no manual
intervention should be needed to boot OpenWrt image. For the older ones
it's necessary to modify default U-Boot environment:

 1. Interrupt boot process to run U-Boot command line,

 2. Run following commands:
    (for version 2017.03-armada-17.06 and 2017.03-armada-17.08)
     setenv bootcmd "load mmc 0:1 0x4d00000 boot.scr; source 0x4d00000"
     saveenv

    (for version 2015.01-armada-17.02 and 2015.01-armada-17.04)
     setenv bootargs "console=ttyMV0,115200 root=/dev/mmcblk0p2 rw rootwait"
     setenv bootcmd "ext4load mmc 0:1 ${fdt_addr} armada-3720-espressobin.dtb; ext4load mmc 0:1 ${kernel_addr} Image; booti ${kernel_addr} - ${fdt_addr}"
     saveenv

 3. Poweroff, insert SD card with OpenWrt image, boot and enjoy.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-03-10 01:15:22 +01:00
Ryan Mounce
7b33f6c1bb mvebu: disable DSA DT nodes for boards using mvsw61xx
As at this commit, DSA is not enabled in the kernel config for mvebu, so these
nodes have been ignored. In preparation for the first mvebu board using DSA,
disable these nodes for existing boards to avoid issues.

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
2018-03-09 22:19:07 +01:00
Stijn Segers
b5469b38cd kernel: bump 4.14 to 4.14.23
This patch bumps the 4.14 kernel to .23.
- Refreshed patches.
- Deleted bcm53xx/patches-4.14/089-PCI-iproc-Fix-NULL-pointer-dereference-for-BCMA.patch. Has been accepted upstream.
- Deleted generic/pending-4.14/821-usb-Remove-annoying-warning-about-bogus-URB.patch. The upstream URB code was changed,
  the patch no longer applies. I discussed this with the patch author and removed it for now, we'll see how it goes.

Compile-tested on: ramips/mt7621, x86/64
Run-tested on: ramips/mt7621, x86/64

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2018-03-02 21:33:08 +01:00
Jonas Gorski
c5b06da56c mvebu: add missing patch for reprobing SFP phys for 4.14
Add the patch for reprobing phys also for 4.14, as it is still needed.

Fixes: 4ccad92229 ("mvebu: Add support for kernel 4.14")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-02-25 22:58:40 +01:00
Jonas Gorski
39f8751cdc mvebu: fix SFP insert detection GPIO name on 4.14
When SFP support was accepted upstream, the expected GPIO names were
slightly changed, breaking SFP insert detection. Update the DTS file to
the expected name to make SFP work again.

Fixes: 4ccad92229 ("mvebu: Add support for kernel 4.14")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-02-25 22:58:35 +01:00
Koen Vandeputte
aad1f11efe kernel: refresh patches
Some fuzz was introduced due to the netfilter-offload series

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-02-22 12:46:25 +01:00
Hauke Mehrtens
4ccad92229 mvebu: Add support for kernel 4.14
Add support for kernel 4.14 to the mvebu target.

This also replaces the old sfp and phylink patches with new versions
from Russell's clearfog-4.13 branch
http://git.arm.linux.org.uk/cgit/linux-arm.git/log/?h=clearfog-4.13

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-02-13 22:29:56 +01:00