TP-Link Archer C7 v5 is a dual-band AC1750 router, based on Qualcomm/Atheros
QCA9563+QCA9880.
Specification:
- 750/400/250 MHz (CPU/DDR/AHB
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 10x LED, 2x button
- UART header on PCB
Flash instruction:
1. Upload lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin via Web interface
Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin
and rename it to ArcherC7v5_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Arvid E. Picciani <aep@exys.org>
Apparently there are RPi1 devices with BRCM43430 wifi, such as the
Pi Zero W. Add the necessary packages for that to the image generated
for those boards as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add the missing enable and disable function.
Remove dummy mask and unmask function and use the one provided by
irq_dummy_chip.
Allow interrupt status register being defined from dts.
Add ddr_wb_flush for ar934x/qca953x.
Rename controller name to qca,ar9340-intc because this design was
first introduced in AR934x.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
ELECOM WRC-1167GHBK2-S is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7621A.
Specification:
- MT7621A (2-Cores, 4-Threads)
- 128 MB of RAM (DDR3)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz
- MediaTek MT7615D
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 2x keys
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- baudrate: 57600 bps
Flash instruction using factory image:
1. Rename the factory image to "wrc-1167ghbk2-s_v0.00.bin"
2. Connect the computer to the LAN port of WRC-1167GHBK2-S
3. Connect power cable to WRC-1167GHBK2-S and turn on it
4. Access to "http://192.168.2.1/details.html" and open firmware
update page ("手動更新（アップデート）")
5. Select the factory image and click apply ("適用") button
6. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
NEC Aterm WG2600HP is a 2.4/5 GHz band 11ac router, based on Qualcomm
IPQ8064.
Specification:
- IPQ8064 (384 - 1,400 MHz)
- 512 MB of RAM
- 32 MB of Flash (SPI)
- 4T4R 2.4/5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 12x LEDs, 4x keys
- 1x USB 3.0 Type-A
- UART header on PCB
- RX, TX, NC, GND, Vcc from power connector side
- baudrate: 115200 bps
Flash instruction using initramfs image:
1. Connect serial cable to UART header
2. Connect power cable and turn on the router
3. When the "Press the [f] key and hit [enter] to enter failsafe mode"
message is displayed on the console, press the "f" key and Enter key
sequentially to enter the failsafe mode
4. create fw_env.config file with following contents on failsafe mode:
/dev/mtd9 0x0 0x10000 0x10000
5. Execute following commands to add and change the environment
variables of U-Boot
fw_setenv ipaddr "192.168.0.1"
fw_setenv serverip "192.168.0.2"
fw_setenv autostart "yes"
fw_setenv bootcmd "tftpboot 0x44000000 wg2600hp-initramfs.bin;
bootipq"
6. Set the IP address of the computer to 192.168.0.2, connect to the LAN
port of WG2600HP, and start the TFTP server on the computer
7. Rename OpenWrt initramfs image for WG2600HP to
"wg2600hp-initramfs.bin" and place it in the TFTP directory
8. Remove power cable from WG2600HP, reconnect it and restart WG2600HP
9. WG2600HP downloads initramfs image from TFTP server on the computer,
loads it and boot with initramfs image
10. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with the sysupgrade image
11. Wait ~180 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Add wpad-mini if wireless drivers are included. Drop the mt76 package if
both of the provided drivers are included with their own packages.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Currently arc770 is no more "source-only".
Lets update Linux kernel version from 4.9 to 4.14 for arc770.
config-4.14 was simply regenerated with "make kernel_menuconfig".
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: John Crispin <john@phrozen.org>
This commit adds support for the Mikrotik wAP R (RBwAPR-2nD). The change
is based on 3b15eb0 which added support for the wAP 2nD. This change lacks
LED support.
Specifications:
- SoC: Qualcomm QCA9531 (650 MHz)
- RAM: 64 MB
- Storage: 16 MB NOR SPI flash
- Wireless: built-in QCA9531, 802.11b/g/n 2x2:2
- Ethernet: 1x100Mbps
- Power: 9-30V Passive PoE, 9-30V DC jack, 9-30V automotive jack
- SIM card slot
- Mini-PCIe slot
Installation:
1. Login to the Mikrotik WebUI to backup your licence key
2. Change the following settings in System->Routerboard->Settings:
- Boot device: try ethernet once then NAND
- Boot protocol: DHCP
- Force Backup Booter: checked
3. Setup a DHCP/BOOTP server with:
- DHCP-Option 66 (TFTP server name) pointing to a local TFTP
server within the same subnet of the DHCP range
- DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
of the to be booted image, e.g.
openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
4. Power off the device
5. If this is the second attempt to boot OpenWRT or the boot device isn't
"try ethernet once then NAND," press and hold the reset button while
powered off. If this is the first attempt, this step isn't necessary.
6. Power on the device, holding the reset button for 15-20s if already
pressed from the previous step.
The board should load and start the initramfs image from the TFTP
server. Login as root/without password to the started OpenWRT via SSH
listing on IPv4 address 192.168.1.1. Use sysupgrade to install OpenWRT.
Revert to RouterOS
Use the "rbcfg" package on in OpenWRT:
- rbcfg set boot_protocol bootp
- rbcfg set boot_device ethnand
- rbcfg apply
Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.
Click on install again.
In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall.
Signed-off-by: David Ehrmann <ehrmann@gmail.com>
GRO stores packets as fraglist. If they are routed back to the ethernet
device, they need to be re-segmented if the driver does not support
sending fraglists.
Add the missing support for that, along with a missing feature flag that
allows full routed GRO->TSO offload.
Considerably reduces CPU utilization for routing
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This commit adds support for the AVM Fritz!WLAN Repeater 450E
SOC: Qualcomm QCA9556 (Scorpion) 560MHz MIPS74Kc
RAM: 64MB Zentel A3R12E40CBF DDR2
FLASH: 16MiB Winbond W25Q128 SPI NOR
WLAN1: QCA9556 2.4 GHz 802.11b/g/n 3x3
INPUT: WPS button
LED: Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4GHz WiFi (correct MAC)
- Installation via EVA bootloader
- OpenWRT sysupgrade
- Buttons
- Most LEDs
Not working:
- 2 RSSI LEDs
AVM used for RSSI{0,1} two of the Ethernet PHYs LEDs which they
control over MDIO. Our driver doesn't expose these LEDs as GPIOs.
While it is possible to implement this feature, it would require an
additional kernel patch for a minor functionality.
Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes.
You need to powercycle the Device afterwards to boot OpenWRT.
Signed-off-by: David Bauer <mail@david-bauer.net>
The QCA9556 only has a SGMII interface. However the speed on the
ethernet link is set for the non-existant xMII interface.
This commit fixes this behavior.
Signed-off-by: David Bauer <mail@david-bauer.net>
Enable the Hardware Random Number Generator Core infrastructure
in kernel.
Needed for hardware random number generator drivers like chaoskey
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
The kernel patch *-mips_module_reloc.patch breaks dynamic ftrace as
dynamic ftrace depends on -mlong-calls.
See http://patchwork.linux-mips.org/patch/675/
Thus we always set -mlong-calls if the kernel is being
compiled with dynamic ftrace support.
Signed-off-by: Vincent Wiemann <webmaster@codefetch.de>
Marvell ahci hardware requires a workaround to prevent eSATA failures
on hotplug/reset when used with multi-bay external enclosures.
Errata Ref#226 - SATA Disk HOT swap issue when connected through Port
Multiplier in FIS-based Switching mode.
These patches backport the workaround from 4.17.
Signed-off-by: Jeremiah McConnell <miah@miah.com>
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 128 MB Nanya NT5CC64M16GP-DI
FLASH: 16 MiB Macronix MX25L12845EMI-12G
ETH: Qualcomm QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT: WPS, Mode-toggle-switch
LED: Power, WLAN 2.4GHz, WLAN 5GHz, LAN, WPS
(LAN not controllable by software)
(WLAN each green / red)
SERIAL: Header next to eth-phy.
VCC, TX, GND, RX (Square hole is VCC)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet (Correct MAC-address)
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from tftp
- OpenWRT sysupgrade
- LEDs
- WPS Button
Not Working:
- Mode-toggle-switch
Install via TFTP:
Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command `tftpboot` will pull an initramfs image named
`C0A86302.img` from a tftp server at `192.168.99.08/24`.
After successfull transfer, boot the image with `bootm`.
To persistently write the firmware, flash an openwrt sysupgrade image
from inside the initramfs, for example transfer
via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device
with `sysupgrade -n /tmp/<sysupgrade>`.
append-cmdline patch taken from chunkeeys work on the NBG6617.
Signed-off-by: Magnus Frühling <skorpy@frankfurt.ccc.de>
Co-authored-by: David Bauer <mail@david-bauer.net>
Co-authored-by: Christian Lamparter <chunkeey@googlemail.com>
ar71xx/ar913x series use the old pll registers and settings.
However started from ar7242, a new pll register is introduced and the
pll setting is much simpler.
This can be observed from dev-eth.c from the ar71xx target.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
This patch adds dts for qca956x and also support for Phicomm K2T
The qca965x.dtsi adds nearly all the necessary components.
Both ath9k AHB and PCIe worked well.
The Phicomm K2T uses MTD partition 'config' to store the mac addresses in
JSON format. To extract these fields correctly, a script is introduced:
/lib/functions/k2t.sh
This script provides a helper function to extract mac addresses, and is used
in three places.
Hardware spec of Phicomm K2T:
CPU: QCA9563
DRAM: 64MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337
WiFi 5.8GHz: QCA9886
Flash instruction:
Apply sysupgrade.bin via serial console:
tftp 0x80000000 sysupgrade.bin && erase 0x9f090000 +$filesize && cp.b $fileaddr 0x9f090000 $filesize
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
This fixup ip align in essedma driver rx path
see cat /proc/cpu/alignment
which reports alignment-fixups without this fix.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Backport a hot off the press upstream kernel ATM fix:
Preserve value of skb->truesize when accounting to vcc
"There's a hack in pskb_expand_head() to avoid adjusting skb->truesize
for certain skbs. Ideally it would cover ATM too. It doesn't. Just
stashing the accounted value and using it in atm_raw_pop() is probably
the easiest way to cope."
The issue was exposed by upstream with:
commit 14afee4b6092fde451ee17604e5f5c89da33e71e
Author: Reshetova, Elena <elena.reshetova@intel.com>
Date: Fri Jun 30 13:08:00 2017 +0300
net: convert sock.sk_wmem_alloc from atomic_t to refcount_t
But an earlier commit left the ticking timebomb:
158f323b9868 ("net: adjust skb->truesize in pskb_expand_head()
Sincerest thanks to Mathias Kresin <dev@kresin.me> for debugging
assistance and to David Woodhouse <dwmw2@infradead.org> for further
guidance, cajoling & patience in interpreting the debug I was giving him
and producing a fix!
Fixes FS#1567
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
When upstream kernel introduced commit c55fa3cccbc2c672e7f118be8f7484e53a8e9e77
we incorrectly updated our hack integration patch that updates atm/common.c
+++ b/net/atm/common.c
@@ -62,10 +62,16 @@ static void vcc_remove_socket(struct soc
write_unlock_irq(&vcc_sklist_lock);
}
+struct sk_buff* (*ifx_atm_alloc_tx)(struct atm_vcc *, unsigned int) = NULL;
+EXPORT_SYMBOL(ifx_atm_alloc_tx);
+
static bool vcc_tx_ready(struct atm_vcc *vcc, unsigned int size)
{
struct sock *sk = sk_atm(vcc);
+ if (ifx_atm_alloc_tx != NULL)
+ return ifx_atm_alloc_tx(vcc, size)
The correct solution is to drop our ifx_atm_alloc_tx replacement hack
entirely and let the kernel do its thing.
In reality neither pppoatm or BR2684 interfaces actually hit this code,
so the incorrect integration would only be noticed with direct socket
calls which we are unaware of a use-case.
This is not the solution to pppoatm vc-mux failing to work which started
the whole investigation, but let's fix it up anyway.
With sincerest thanks to David Woodhouse <dwmw2@infradead.org> &
Mathias Kresin <dev@kresin.me>.
Tested-on: lantiq, BT HomeHub 5a
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Support for these devices isn't ready yet and it was only accidentally
pushed in the commit 0da9303e5b ("mac80211: backport "brcmfmac:
cleanup and some rework" from 4.17").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
For easier future kernel bumps replace spi patch with upstream version
slightly modified. The modification removes partition definitions which
has been diffrent for some U-Boot versions.
Also this removes unnecessary i2c definition which was in the old patch.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Since the beginning there's been an issue with initializing the Atheros
based MiniPCIe wireless cards. Here's an example of kerenel log:
OF: PCI: host bridge /soc/pcie@d0070000 ranges:
OF: PCI: MEM 0xe8000000..0xe8ffffff -> 0xe8000000
OF: PCI: IO 0xe9000000..0xe900ffff -> 0xe9000000
advk-pcie d0070000.pcie: link up
advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [mem0xe8000000-0xe8ffffff]
pci_bus 0000:00: root bus resource [io 0x0000-0xffff](bus address[0xe9000000-0xe900ffff])
pci 0000:00:00.0: BAR 0: assigned [mem0xe8000000-0xe801ffff 64bit]
pci 0000:00:00.0: BAR 6: assigned [mem0xe8020000-0xe802ffff pref]
[...]
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x3c
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x44
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4
ath9k 0000:00:00.0: enabling device (0000 -> 0002)
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x3c
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0xc
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x40
ath9k 0000:00:00.0: request_irq failed
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4
ath9k: probe of 0000:00:00.0 failed with error -22
The same happens for ath5k cards, while ath10k card didn't appear at
all (not detected):
OF: PCI: host bridge /soc/pcie@d0070000 ranges:
OF: PCI: MEM 0xe8000000..0xe8ffffff -> 0xe8000000
OF: PCI: IO 0xe9000000..0xe900ffff -> 0xe9000000
advk-pcie d0070000.pcie: link never came up
advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [mem0xe8000000-0xe8ffffff]
pci_bus 0000:00: root bus resource [io 0x0000-0xffff](bus address[0xe9000000-0xe900ffff])
advk-pcie d0070000.pcie: config read/write timed out
Following the issue on esppressobin.net forum [1] the workaround seems
to be limiting the speed of PCIe bridge to 1st generation. This fixed
the initialisation of all tested Atheros wireless cards.
The change shouldn't affect the performance for wireless cards,
it could reduce the performance of storage controller cards but since
OpenWrt focuses on wireless connectivity, fixing compatibility with
wireless cards should be a priority.
For the record, the iwlwifi and mt76 cards were not affected by this
issue.
1. http://espressobin.net/forums/topic/which-pcie-wlan-cards-are-supported
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
zram.ko needs CONFIG_BLK_DEV activated and it is by default for all
other targets in OpenWrt.
This makes zram.ko compile again.
Compile tested only.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Neon and vfpv4 are mandatory extensions in the ARM64 instruction set
now, do not activate them explicitly. GCC will make use of these
extension now by default.
This makes it possible to share the toolchain with other Cortex A53
SoCs.
Compile tested only.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds the get_status_led method to diag.sh, which sets the
boot-led as status-led for scripts using this method to get a
status-led.
This method is used platform-independent in downstream project gluon to
set the LED used to indicate the config-mode.
Signed-off-by: David Bauer <mail@david-bauer.net>
This generates the "rd.gz" and "hddapp.tgz" that doesn't contain
anything of the sort but rather the OpenWRT rootfs. It works the
same way as how we generate the same layout for the NAS4220b.
For some reason the ImageInfo file is different for the SQ201.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The D-Link DIR-685 has a RealTek RT2880 mini-PCI card in a
slot. Activate the appropriate kernel module.
The Square One SQ201 has a Ralink RT61-based mini-PCI card.
Activate the appropriate kernel modules. This fixes the
previous error just activating the firmware: the kernel
module will bring in the firmware it needs.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the Gemini build a WRGG-type firmware update
image for the DIR-685. This should hopefully install the
kernel from the web firmware upgrade API on the product
switching it permanently to use OpenWRT.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It was described by Arend as:
> This series is intended for 4.17 and includes following:
>
> * rework bus layer attach code.
> * remove duplicate variable declaration.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This fixes missing rootfs on above device:
[ 2.652292] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
(...)
[ 2.687909] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
Fixes: 05cb6aa69f ("bcm53xx: replace linux,part-probe with a proper partitions subnode")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
1. Move all status led definitions out of diag.sh into device dt
as we use here a generic script hook.
2. Encode "phy0ptp" led trigger in dt of device for all ath79 devices.
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
