The CPE210's ancestor is the CPE510 not the other way around. The device
profile is also named after the CPE510.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
The bootloader on this device expects the kernel partition to end
on a 64k boundary. The last 64 byte of the kernel partition must
contain a valid uImage header (the fakeroot partition).
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
1)Changes
- Rebased the patches for linux-4.4.7
- Added patch to fix spi nor fifo and dma support
- Added patch to configure watchdog barktime
2)Testing
Tested on IPQ AP148 Board:
a. NOR boot and NAND boot
b. ethernet network and ath10k wifi
c. ubi sysupgrade
UnTested
dwc3 usb has not been validated on IPQ board(AP148)
3)Known Issues:
Once we flash ubi image on AP148, and if we reset the board, uboot on
first boot creates PEB and LEB for dynamic sized partitions, which is incorrect
and not what linux expects which causes errors when trying to mount rootfs.
In order to test this, we can use the below steps:
a. Flash the ubi image on board and don't reset the board
b. load the kernel fit image in RAM and boot from there.
Signed-off-by: Ram Chandra Jangir <rjangi@codeaurora.org>
The user benpicco in #openwrt reported that images are build which are
bigger that the available flash size.
He provided a proof of concept fix and gave permission to me to send it
for inclusion.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The RJ45 WAN port is used for xDSL as well as the IP101A.
The pins 1,2,3,6 of the RJ45 are connected to the IP101A and the
pins 4,5 are connected to the xdsl chip.
Drop the ip101a-rst node. It can't be controlled and is not required
at all.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The STP pinmux was initially added in assumption LAN2 led is driven by
it. It worked somehow because STP group and gphy0 led0 share the GPIO.
Do it the right way by adding the gphy0 led0 the gphy function.
According to the author, the SPI node is a copy & paste leftover. Which
makes sense since nothing is connected to the SPI bus on this device.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the brnboot partition layout as it is listed in the OpenWrt wiki
article for this board.
Configure the brnboot root selector for this device as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Cleanup the pinmux configuration by removing the unused spi node. Nothing is connected to the SPI bus on devices.
The stp_out pinmux child node covers the same GPIOs as the already used
stp group.
The same applies to the gphy-leds_out pinmux node and the "gphy0
led1" as well as "gphy1 led0" groups.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch fixes the missing Lan interface config in the file
/etc/config/network for ARV4518PWR01/A which results in eth0 and br-lan
being down and therefore no way to access the router unless via UART-TTL.
Signed-off-by: Mohammed Berdai <mohammed.berdai@gmail.com>
RB912 has one usb shared between external USB and miniPCIe slot. GPIO52 can
reroute power to external USB (=1) or internal miniPCIe slot (=0)
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Commit d79f8909c1 introduced CONFIG_ALL,
CONFIG_ALL_KMODS and CONFIG_ALL_NONSHARED as menuconfig choices to the SDK,
therefor we can drop the hardcoded CONFIG_ALL symbol declaration now.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Now that the most important options are exposed via menuconfig in the SDK we
can stop shipping a (possibly outdated) copy of .config from the emitting
buildroot.
Leaving out .config has two positive side effects:
- A simple "make" run without any prior config will launch menuconfig, forcing
interactive users to make appropriate choices
- Buildbot systems (e.g. our phase2 builder) can issue a "make defconfig" to
obtain a .config enabling all packages by default
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The query for ARMADA_THERMAL is stalling the kconfig process and as long as we
do not package it, simply disable the symbol.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Generalize the partition discovery in sysupgrade in order to fix sysupgrade
and config backup/recovery on MMC block devices which use a different naming
scheme compared to mtdblock or sd* devices.
The change also adds the find applet to the ramdisk utilities so that upgrade
code can rely on it.
The commit is based on the initial submission by Russell Senior at
http://patchwork.ozlabs.org/patch/625440/ .
Signed-off-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
It is desirable to be able to use ./scripts/feeds install -a
when in the SDK without being forced to build a great number
of packages that are not actually wanted.
We therefore add the option of changing the various ALL package
build options so that we can default to packages not being built
unless we select them.
Signed-off-by: Daniel Dickinson <lede@daniel.thecshore.com>
The cpe510 has two calibration tables. The first calibration
table requires to modify ath9k driver to work (patched tx gain table).
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
The CE image format used by OpenMesh can contain extra blocks which
are not used for flashing. Only the first three embedded images
(fwupgrade.cfg, kernel, rootfs) are required in this order to successfully
flash an image via sysupgrade. All extra embedded images should be ignored
for the available devices.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
The platform_check_image_openmesh function used break statements to signal
that the board name matched the image target. This worked because the
sysupgrade binary checked the image inside a loop. The break statement
stopped the loop and skipped any additional check.
Instead the check should be done without such sideeffects by simply
combining the board names and image targets. Only a mismatch should cause a
negative result for the caller and skipping of the additional checks.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Some OpenWrt based firmwares like Gluon expect that a sysupgrade image
exists when a device firmware can be updated via sysupgrade. This image
wasn't created until now because OpenMesh devices use the same image for
factory and sysupgrade flash. Copying the image from *factory.bin to
*sysupgrade.bin is therefore enough to make the sysupgrade functionality
visible.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
