This patch adds support for the Sitecom WL-341 v3 and other Sercomm
IP1006RRv2 based boards for sysupgrade support and for the initial
flash through pushbutton initiated recovery mode with the special
partition table and fixes for the quirks and things required by the
modified bootloader.
There is a known bug, Wi-Fi is not working on my board probably
because of the lack of RAM (the board only has 16MiB ram -- half of
the normal amount for non rebadged versions, but there is an empty
slot for another ram chip,) but I don't know for sure. The driver
loads but hostapd fails to load so I think it's not related to the
specific device except for the lack of RAM.
Moreover, only 7 of the 11 onboard leds are confirmed working, it
seems that one of the others is always on and the remaining ones are
connected to the wireless card leds already recognized by OpenWrt
[juhosg: reordered some parts in order to keep things sorted
alphabetically]
Signed-off-by: Marco Antonio Mauro <marcus90@gmail.com>
SVN-Revision: 29910
This patch fixes the board detection of the TL-MR3020.
The LED behaviour has also been modified:
* The WPS LED is the diag LED now.
* A netdev trigger for the LAN LED has been added.
The profile of the TL-MR3020 has been updated because the needed package
"kmod-ledtrig-usbdev" was missing which resulted in a non-working usbdev
trigger for the 3G/USB LED.
[juhosg: the board name changes has been removed, and the kernel files
has been changed instead.]
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
SVN-Revision: 29905
This patch fixes the GPIO polarity for the button and the sliding
switch. The buttons are not active low. "Pressed" and "Released"
events are wrong without the patch.
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
SVN-Revision: 29904
In this patch:
* rename Argus leds to avoid underscores
* rename Belkin F5D8235 v1 leds from f5d8234 to f5d8235
* remove Belkin F5D8235 v1 status led defined as storage led (it was
defined as usb led earlier, just in wrong place) - it should have
router led as in v2
* add Argus, Sparklan and Belkin F5D8235 v2 status leds
* add Belkin F5D8235 v1 and v2 usb leds
* fix Belkin F5D8235 v2 network config generation and mac address axtraction
* fix Sparklan board identification
* add Sparklan usb led (this board doesn't have usb connector by
default and the led is hidden also but if you are going to solder
the connector then you'll see the led too)
* add Sparklan network config generation and mac address extraction
* fix empty string test in network script and...
* ...sort case entries by the first board in the list
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 29871
After issuing a soft reset on the RT8366{S,RB}
switch, waiting for the last acknowlegement fails
in rtl8366_smi_write_reg. Add a _noack version of
the function and use that for issuing a soft reset.
SVN-Revision: 29844
* fixes leds
* adds all leds found on the sx763 board
* removes board_config from flash layout because wireless data is stored in kernel (ath5k)
* fix button handling
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
SVN-Revision: 29763
Previously the tx housekeeping was done in a spin_lock_irqsave critical
section which causes irqs to be disabled during that time. Since the
housekeeping is already prepared to be scheduled as a tasklet process
the housekeeping only in softirq context and revise the locking between
the tx path and the housekeeping tasklet by using a normal spin_lock
which in most situations will be a NOP anyway.
This makes sure that interrupts are only disabled for a short time
since in the worst case the housekeeping might have to free up to 256
skbs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 29762
