Source package gre was depending on kmod-ip6-gre, however the actual
kernel module package that is created is kmod-gre6. Therefore
update (source) package gre for ipv6 gre support.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 48100
In sta-only configuration, wpa_supplicant needs correct regulatory
domain because otherwise it may skip channel of its AP during scan.
Another alternative is to fix "iw reg set" in mac80211 netifd script.
Currently it fails if some phy has private regulatory domain which
matches configured one.
Signed-off-by: Dmitry Ivanov <dima@ubnt.com>
SVN-Revision: 48099
iproute2-4.0 had connmark support added by nbd. This does not work
with 4.x kernels. iproute2-4.3 is the latest version and has his
changes mainlined. This patch updates the package to iproute2-4.3
and fixes the patches so that it compiles. This should resolve
ticket #21374.
Signed-off-by: Rob Mosher <nyt-openwrt@countercultured.net>
SVN-Revision: 48098
Add back a slightly modified version of the lowlevel settings which
where removed with r46920.
In compare to the old lowlevel settings, the B43c tone is added to
tone_adsl_b and tone_adsl_bv.
If an unsupported tone value is used, the auto probing mode is used, in
compare to the fallback to tone_adsl_av and tone_vdsl_av with the old
lowlevel settings.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48054
According to ITU-T G.997.1 Amendment 2 (04/2013) section 2.1, bit 3 of
XTSE octet 8 either allow or denies the initialization of G.993.5.
Even if the current redistributable xDSL firmware doesn't include
G.993.5 vectoring support, enable this bit by default to allow people to
get their G.993.5 line working using a custom xDSL firmware.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48053
r47933 revealed that the driver/app in combination with the chosen
firmware does a good job in selecting a working xtse.
Use this probing mode if no annex is specified.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48052
This patch adds the missing VDSL2 bits to the annex specific XTSE (like
it should be according to the comments above the XTSE bits).
Since r47933 it's mandatory to remove the annex option to switch to
VDSL2 (only) operation mode.
As shown by ticket #21436 and a few mails I received personally, even
experienced users are not aware that they have to remove the annex
option to get their VDSL2 line working and as shown by this patch it
doesn't need to be that "complicated".
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48051
MD5SUM is wrong, it was not updated during last update to v1.4.1.
Thanks to Daniel Dickinson <openwrt@daniel.thecshore.com> for reporting it.
Signed-off-by: Nicolas Thill <nico@openwrt.org>
SVN-Revision: 48017
Changed the tunnel update URL into format tunnelbrokers
example has, that made it work again. Current method gives "Username/Password
Authentication Failed." when I tried the wget line manually and logread
eventually says also "6in4: update failed". With corrected URL it works fine:
"good 111.222.333.444" or "nochg 111.222.333.444" and logread concurs with
success, and tunnel actually updates.
Tested-by: Vaasa Hacklab <info@vaasa.hacklab.fi>
Signed-off-by: Sami Olmari <sami@olmari.fi>
SVN-Revision: 48006
When using cli, print link state the same way kernel used to do it.
This will allow kernel switching PORT_LINK from SWITCH_TYPE_STRING.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47998
Only the conditional dependency ought to be required;
if build fails with JSON there is some other problem
at work.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47976
By default dnsmasq sends an ICMP echo request before allocating
an IP address to a host; the uci option noping allows to disable
this check.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 47974
Changed option nonwildcard from --bind-interfaces into --bind-dynamic.
With this, Dnsmasq binds the address of individual interfaces, allowing multiple
dnsmasq instances, but if new interfaces or addresses appear, it automatically
listens on those. This makes dynamically created interfaces work in the same way as
the default, but allows also use of other DNS-servers (like Named) at the same time
on diffirent interfaces where Dnsmasq is NOT configured, whereas with
--bind-interfaces will still reserve every interface even if not used and thus
disallowing use of any other DNS-program even on unused interfaces.
Tested-by: Vaasa Hacklab <info@vaasa.hacklab.fi>
Signed-off-by: Sami Olmari <sami@olmari.fi>
SVN-Revision: 47953
Using the JSON output option depends on json library so
add select json-c library when JSON output is selected.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47928
- 1.4.x has IPv6 support
- set C std explicitly due to gcc 5 changes/old code style of dante
- disable pam via configure vars since detection of without pam option
is broken (-lpam gets linked in if available)
- remove and refresh patches
only compile tested
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 47926
- CONFIG_IFX_CLI is unused, couldn't find any reference to this config variable
- use disable-feature instead of enable-feature=no
- reorder configure args to have depending args together
- remove configure args which set the default value
- group enable-model and configure args which enable or disable features that
are covered by the feature set
The config.log contains the same values as before. The vdsl_cpe_control binary
has the same checksum as before.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47888
The typicial feature set doesn't include "DSL PM showtime counters support"
(INCLUDE_DSL_CPE_PM_SHOWTIME_COUNTERS). This feature provides the
vdsl_cpe_control command 'pmccsg', which is used by 'dsl_control status' to get
the line uptime.
The binary size increases to 103912 byte (+4256 byte) uncompressed.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47887
Add the option "--all-servers" which forces dnsmasq to send all
queries to all servers and then take the first answer.
Signed-off-by: Andréas Gustafsson <gurgalof@gmail.com>
SVN-Revision: 47857
this error was not visible until recent bump to
busybox 1.24.1 stable which introduced a warning message
when keyword 'local' is not used with a shell-function.
this does not change behavior and is a cosmetic cleanup.
fixes the following output:
root@box:~ ifup <interface>
/sbin/ifup: local: line 362: not in a function
/sbin/ifup: local: line 362: not in a function
/sbin/ifup: local: line 1: not in a function
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 47828
This should ensure that lldpd is among the first processes to stop,
so that it has time to send the shutdown LLDPU to the other side,
before the network goes down.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 47786
Support next to the non-HT/HT channel widths like HT20 or NOHT also VHT80
channels during the mesh join
iw dev mesh0 mesh join "meshnet" freq 5180 80MHz
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47782
Fix the id of NL80211_ATTR_WIPHY_ANTENNA_GAIN for antenna_gain command when
using compat-wireless 2015-10-26.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47778
Use the 'typical' compile configuration instead of 'full', which most
notably excludes the soap support.
/sbin/vdsl_cpe_control shrinks down to ~50%, from 178kb(!) to 90kb.
Signed-off-by: Andre Heider <a.heider@gmail.com>
SVN-Revision: 47769
In this upstream dsl driver app version the autoboot is deactivated activate
it again.
In addition to the update this also fixes some build warnings and makes it
use the same configure option as used in Lantiq UGW.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
SVN-Revision: 47637
The scripts for authsae and iw use the option mesh_id to get set the
"meshid" during a mesh join. But the script for wpad-mesh ignores the
option mesh_id and instead uses the option ssid. Unify the mesh
configuration and let the wpa_supplicant script also use the mesh_id from
the configuration.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47615
The OpenWrt wireless configuration for mcast_rate is defined as Kbit/s when
using wpa_supplicant for IBSS/802.11s and iw for unencrypted IBSS/802.11s.
But when using authsae, the unit for the same option is redefined as
Mbit/s. Better use the same unit for this option independent of the backend
which is used.
Old values for mcast_rate (< 1000) are still interpreted Mbit/s to avoid
problems during upgrades from older versions.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47614
The variable $mesh_id was never defined in authsae_start_interface and thus
the option meshid in $authsae_conf_file was always set to "".
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47613
Fixes compilation with Linux 4.3. Runtime tested on Ubiquiti EdgeRouter
Lite with Linux 3.18, 4.1 and 4.3.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
SVN-Revision: 47470
Only costs about 3k compressed, but significantly improves handling of
configuration mismatch
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47439
as conntrack and conntrackd are completely independent programs,
serving a different purpose.
Also split by other distributions, as Debian and Ubuntu.
Signed-off-by: Ulrich Weber <uw@ocedo.com>
SVN-Revision: 47424
default configuration will fill up disk by
writing /var/log/conntrackd-stats.log
Introduced due init script auto start.
Signed-off-by: Ulrich Weber <uw@ocedo.com>
SVN-Revision: 47422
Seems the default one is not working as expected.
The way that reload should work is that the 'start' service
call should return 1 (if lldpd is running) and then a normal
restart would be called.
However, for lldpd a reload would mean just clearing all custom TLVs
(if they're configured) and reloading the configuration.
So, this patch adds a reload hook, which would:
- 'start' lldpd if it's not running (because we return 1 if not running)
- reload configuration if it is running (also previously
clearing custom TLVs if present)
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 47367
r46861 introduced a new option eapol_version to hostapd, but did not
provide a default value. When the option value is evaluated,
the non-existing value causes errors to the systen log:
"netifd: radio0: sh: out of range"
Add a no-op default value 0 for eapol_version. Only values 1 or 2 are
actually passed on, so 0 will not change the default action in hostapd.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 47361
Update iperf3 to point to the correct project website. Prior URL was the
old iperf2 website.
Signed-off-by: Karl Palsson <karlp@remake.is>
SVN-Revision: 47184
The two commits
5162e3b0ee7bd1d0fd6e75e1ca7993a1834b5291
"allow request handlers to disable chunked reponses"
and
618493e378e2239f0d30902e47adfa134e649fdc
"file: disable chunked encoding for file responses"
broke the chunked transfer encoding handling for proc responses in keep-alive
connections that followed a file response with http status 204 or 304.
The effect of this bug is that cgi responses following a 204 or 304 one where
sent neither in chunked encoding nor with a content-length header, causing
browsers to stall until the keep alive timeout was reached.
Fix the logic flaw by inverting the chunk prevention flag in the client state
and by testing the chunked encoding preconditions every time instead of
once upon client (re-)initialization.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47161
One second is not enough for some devices to ackowledge null data frame
which is sent at the end of ap_max_inactivity interval. In particular,
this causes severe Wi-Fi instability with Apple iPhone which may take
up to 3 seconds to respond.
Signed-off-by: Dmitry Ivanov <dima@ubnt.com>
SVN-Revision: 47149
Seems the match pattern was being adapted from 'eth0' to ' eth0'
because of the way I added the procd command args.
This did not seem to be a problem when there were multiple interfaces,
just on devices with single interfaces for lldpd to listen on.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 47136
OpenVPN 2.3 added a route-pre-down option, to run a command before
routes are removed upon disconnection.
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
SVN-Revision: 47134
When using FullMAC drivers (e.g. brcmfmac) we don't get mgmt frames so
check for banned client in probe request handler won't ever be used.
Since cfg80211 provides us info about STA associating let's put a check
there.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47064
There is no RFC requirement that DHCPv6 servers must reply with a link local
address and some ISP servers in the wild appear to using addresses in the ULA
range to send DHCPv6 offers.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47048
Since r46834, IPv6 support is builtin if selected. Therefor, dependencies
on kmod-ipv6 can no longer be fulfilled, since it is not a module anymore.
Signed-off-by: Arjen de Korte <arjen+openwrt@de-korte.org>
SVN-Revision: 47022
Using protocol qmi does not work since qmi.sh is not executable.
Setting option dhcp explicitely to 0 actually enables it.
This patch fixes both problems.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 47014
Our ruleset requires kernel support for conntrack state matching, therfore
depend on the require kmod. Fixes#20542.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 46990
This call is no longer supported.
Maybe a come-back for it would be to use a config /etc/lldpd.conf
or /etc/lldpd.d/<some-file>.conf
Signed-off-by: Alexandru Ardelean <aa@ocedo.com>
SVN-Revision: 46966
Thanks to Sylwester Petela for testing my patch (successfully on an
ADSL connection) and for pointing out some configuration mistakes.
Others (including me) have also successfully tested this extensively
on VDSL connections.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46920
Move the pattern setting from netifd's service script to
/etc/sysctl.conf. Put the timestamp component '%t' just after
executable name '%e' for more natural order from output of ls command.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 46867
Add eapol_version to the openwrt wireless config ssid section.
Only eapol_version=1 and 2 will get passed to hostapd, the default
in hostapd is 2.
This is only useful for really old client devices that don't
accept eapol_version=2.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 46861
