Commit graph

11 commits

Author SHA1 Message Date
Gabor Juhos
b386b5727b ar71xx: fix Kconfig dependency of the 88E6063 switch DSA driver
The Marvell 88E6063 ethernet switch driver depends on the DSA
framework. Add a 'depends on NET_DSA' statement to its Kconfig
entry to state that explicitly.

Fixes the following Kconfig warning:

  warning: (NET_DSA_MV88E6060 && NET_DSA_MV88E6063) selects NET_DSA_TAG_TRAILER which has unmet direct dependencies (NET && NET_DSA)

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-09 08:34:03 +01:00
Hauke Mehrtens
f704b643b9 kernel: Update kernel 4.9 to 4.9.70
Runtime tested on lantiq.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-12-19 22:45:27 +01:00
Gabor Juhos
e7b48fcfe1 ar71xx: fix board detection with newer RouterBOOT versions
Recent RouterBOOT version (at least version 3.41 on RB911G-5HPacD)
use "Board=" kernel parameter instead of "board=" to pass the board
name to the kernel. Due to this change the board detection code is
not working on the devices shipped with the new RouterBOOT version.
Because the kernel is unable to identify these boards they become
unusable despite that they are supported by the current code.

Update the prom_init code to convert the 'Board' kernel parameter to
'board'. After this change, the board detection works also with the
new RouterBOOT versions.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2017-12-12 17:05:25 +08:00
Felix Fietkau
668eb70157 kernel: MIPS compile out no-op DMA mapping ops where possible
Slightly improves networking throughput on some devices

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-12-08 19:55:17 +01:00
Stijn Tintel
f997478655 kernel: bump 4.9 to 4.9.67
Refresh patches.
Remove upstreamed patches:
- generic/190-1-5-e1000e-Fix-error-path-in-link-detection.patch
- generic/190-3-5-e1000e-Fix-return-value-test.patch
- generic/190-4-5-e1000e-Separate-signaling-for-link-check-link-up.patch
- generic/190-5-5-e1000e-Avoid-receiver-overrun-interrupt-bursts.patch
- ramips/0102-MIPS-ralink-Fix-MT7628-pinmux.patch
- ramips/0103-MIPS-ralink-Fix-typo-in-mt7628-pinmux-function
Update patches that no longer apply:
- layerscape/815-spi-support-layerscape.patch
- ramips/0099-pci-mt7620.patch

Compile-tested on ar71xx, brcm2708/bcm2708, octeon and x86/64.
Runtime-tested on ar71xx, brcm2708/bcm2708, octeon and x86/64.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-12-07 01:41:09 +02:00
Koen Vandeputte
62ede4f783 kernel: bump 4.9 to 4.9.63
Refreshed all patches.

Removed upstreamed parts.

Compile-tested: cns3xxx, imx6, mvebu, layerscape
Run-tested: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2017-11-22 20:45:52 +01:00
Robert Marko
ac4a52b5c8 ar71xx: complete support for RB mAP 2nD
This patch adds support for the MikroTik RouterBOARD mAP 2nD
https://mikrotik.com/product/RBmAP2nD

Specifications:

- SoC: Qualcomm QCA9531 (650 MHz)
- RAM: 64 MB
- Storage: 16 MB NOR SPI flash
- Wireless: builtin QCA9531, 2x2:2
- Ethernet: 2x100M (802.3af/at POE in and passive POE out on ETH2)
- USB: microUSB type AB port

This patch adds missing code to fully support mAP. Machfile already
contained configuration for mAP 2nD, but device specific configuration
like LEDs etc., was missing.

Note: The POE LED works but doesn't turn on when POE passthrough is
enabled, despite being configured with GPIO trigger.

Installation

1. Login to the Mikrotik WebUI to backup your licence keys
2. Setup a DHCP/BOOTP server with:
   - DHCP-Option 66 (TFTP server name) pointing to a local TFTP
     server within the same subnet of the DHCP range
   - DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
     of the to be booted image
3. Connect the port labeled internet to your local network
4. Keep the reset button pushed down and power on the board

The board should load and start the initramfs image from the TFTP
server. Login as root/without password to the started LEDE via SSH
listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE.

Revert to RouterOS

Use the "rbcfg" package on in LEDE:
- rbcfg set boot_protocol bootp
- rbcfg set boot_device ethnand
- rbcfg apply

Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.

Click on install again.

In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2017-11-14 22:36:46 +01:00
Robert Marko
3b15eb06c3 ar71xx: complete support for RB wAP 2nD
This patch adds support for the MikroTik RouterBOARD wAP
https://mikrotik.com/product/RBwAP2nD

Specifications:

- SoC: Qualcomm QCA9533 (650 MHz)
- RAM: 64 MB
- Storage: 16 MB NOR SPI flash
- Wireless: built-in QCA9533, 2x2:2
- Ethernet: 1x100M (802.3af/at POE in)

This patch adds missing code to fully support wAP. Machfile already
contained configuration for wAP 2nD but device specific configuration
like LEDs etc. was missing.

Installation:

1. Login to the Mikrotik WebUI to backup your licence keys
2. Setup a DHCP/BOOTP server with:
   - DHCP-Option 66 (TFTP server name) pointing to a local TFTP
     server within the same subnet of the DHCP range
   - DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
     of the to be booted image
3. Connect the port labeled internet to your local network
4. Keep the reset button pushed down and power on the board

The board should load and start the initramfs image from the TFTP
server. Login as root/without password to the started LEDE via SSH
listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE.

Revert to RouterOS

Use the "rbcfg" package on in LEDE:
- rbcfg set boot_protocol bootp
- rbcfg set boot_device ethnand
- rbcfg apply

Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.

Click on install again.

In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2017-11-14 22:36:46 +01:00
Felix Fietkau
645b163cfc ar71xx: fix regression in 74x164 initialization with 4.9
The memcpy of the init data relies on chip->registers to be initialized,
which only happens later in the code. Move this initialization further
down to make it work.
This was breaking PCIe/USB on some MikroTik RouterBoard devices.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-11-10 00:53:10 +01:00
Felix Fietkau
e0d58157d8 ar71xx: fix flash fast read on devices using multiple flash chips
Add a callback to allow the SPI driver to indicate which devices fast
flash read works on.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-11-05 18:52:12 +01:00
Hauke Mehrtens
7bbf4117c6 ar71xx: Add kernel 4.9 support
This add support for kernel 4.9 to the ar71xx target.
It was compile tested with the generic, NAND and mikrotik subtarget.
Multiple members of the community tested it on their boards and did not
report any major problem so far.

Especially the NAND part received some changes to adapt to the new
kernel APIs. The serial driver hack used for the Arduino Yun was not
ported because the kernel changed there a lot.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-10-11 22:32:39 +02:00