This patch adds the eeprom property to the dts for the Asus RP-N53. It is necessary to get the wifi in the soc working.
Signed-off-by: Alberto Mattea <alberto@mattea.info>
SVN-Revision: 47350
Replace use of vconfig with the corresponding iproute2 syntax in
/lib/preinit/07_set_preinit_iface_ramips
The switch reset work-around needed on some ramips targets used the
deprecated vconfig tool to bring up the pre-init/failsafe interface.
This doesn't work on recent builds where vconfig is no longer being
deployed, resulting in the device being unreachable when triggered
into failsafe mode.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 47349
Add support for Dovado tiny AC wifi router.
Soc: mt7620a
ram: 64MB
flash: 8MB
1x usb 2.0
two gigabit lan ports
5ghz wlan is not supported on this board since there is no gpl driverfor mt7610e wifi chip.
Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>
SVN-Revision: 47348
Some boards like dovado tiny ac have generic ralink mac in onflash wifi eeprom.
Add eeprom_set_macaddr function to rt2x00 eeprom extract script which changes mac addr insde eeprom dump.
Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>
SVN-Revision: 47347
Add missing icplus phy driver kernel config symbol to mt7620 subtarget.
This is needed since some mt7620 devices have icplus ip1001 ethernet transceiver
Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>
SVN-Revision: 47346
This patch adds a case for the Asus RP-N53 in the "02_network" boot script. Without this, the lan interface does not get configured on startup, effectively bricking the device.
Signed-off-by: Alberto Mattea <alberto@mattea.info>
SVN-Revision: 47345
add the SDK alsa driver. this has only been tested on mt7628/88 and wm8960.
mt7620 is only compile tested.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 47205
When talking to an atmel controller we need 9600 or 250000 baud.
as 250000 does not exist we use 2500000.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 47204
when sleep mode is disable use MIPS as clocksource and clockevent instead of systick.
because MIPS timer has higher resolution 5ns less than systick 20us and
larger counter bits 32 > 16.
clean interrupt by write compare register at isr.
fix typo cause sleep mode not enable.
Signed-off-by: Michael Lee <igvtee@gmail.com>
SVN-Revision: 47122
Due to datasheet of rt3883 SoC rgmii1 port handles pins 84-95 and rgmii2 port handles pins 72-83. When this function ports gets added to rt3883_pinmux_data there's wrong pinmux bits set (RT3883_GPIO_MODE_GE1 manages 84-95 pins and RT3883_GPIO_MODE_GE2 manages 72-83). So when enabling rgmii2 as GPIO driver confuses hardware and nothing work, neither rgmii nor gpio.
Also in '0030-pinctrl-ralink-add-pinctrl-driver.patch' typo in name of rgmii2 port.
Signed-off-by: Nick Leiten <nickleiten@gmail.com>
SVN-Revision: 47118
The default switch frame size (with FCS + header) is 1536 bytes. But the
GMAC only accepted frames up to 1522 bytes. Setting it to 1536 allows to
receive ethernet frames using the full of MTU 1500 + an extra VLAN header +
VLAN header added by the switch.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47117
The driver assumes that the maximum received buffer for non-jumbo frames is
1536 bytes. But the allocation of the rx fragment doesn't reflect that. It
currently allocates fragments which will only be large enough to be used as
rx buffer with the size of 1534 bytes. This is problematic because the GMAC
will now try to write to 2 bytes which don't belong to its receive buffer
when a large enough ethernet frame is received.
This may already be a problem on existing chips but will at least become a
problem when the 1536 byte rx modus is enabled on MT7621a. It is required
on this SoC to receive ethernet frames which use their full 1500 bytes MTU
and a VLAN header next to the switch VLAN tag.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47116
The length of the DMA rx buffer was always set to 0 because the function
for extracting the length was used to calculate the value for setting it.
Instead the macro has to be split in a get and set function similar to the
TX_DMA_(GET_|)PLEN(0|1) macro.
No problem was noticed on MT7621a before this was changed and thus maybe it
was hidden by different problem which is not yet fixed.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47115
The MT7530 switch driver with enable_vlan set will automatically set all
ports to the user port mode. The hardware will remove the incoming vlan tag
on these ports and use it for its internal vlan. This is usually not wanted
and makes it impossible to communicate via vlan over the switch in both
directions.
It is possible to configure a switch port to "transparent mode" when this
port is only used as untag in the switch VLANs. This will disable the VLAN
untagging of packets when they were received on this port. The tagging on
"tag" ports based on the vlan id is still working.
The transparent port mode cannot be used when a port is both used in a VLAN
as "tag" and in another one as "untag" port.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47114
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com <http://www.hiwifi.com/>. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.
The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.
v3 fix
1: Spaces -> Tabs
2: Removed some packages
Signed-off-by: Xiaoning Kang <kangxn@163.com>
SVN-Revision: 47113
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.
The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.
v3 fix
1: Merged most stuff into dtsi file
2: Remove unnecessary empty lines.
Signed-off-by: Xiaoning Kang <kangxn@163.com>
SVN-Revision: 47112
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.
The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.
v3 fix
1: Fixed model order
2: Remove manufacturer name from model name
3: Use a hacky but prettier way to get mac address.
Signed-off-by: Xiaoning Kang <kangxn@163.com>
SVN-Revision: 47111
The pinctrl-rt2880 code doesn't support multiple functions with the same
name. This will result in a incorrect pinmux configuration.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46963
This patch is to add the WIZnet WizFi630A board as a new platform. The board is in mini pci express form factor.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
SVN-Revision: 46921
This patch add support for Planex DB-WRT01. DANBOARD route on
the MT7620A SoC with two Ethernet port and a 802.11n 2.4 GHz radio.
DANBOARD is Cartoon character.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 46918
The PBR-M1 and other upcoming MT7621 boards have RTC chips on them. The
PBR-M1 also selects the kmod-rtc-pcf8563 by default. But the module itself
will not be build because CONFIG_RTC_CLASS is currently not enabled for its
kernel.
Enabling this option should fix the problem of the missing rtc device on
these boards.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46857
