Commit graph

98 commits

Author SHA1 Message Date
Henryk Heisig
b05c7193fd ar71xx: add support for TP-Link Archer C58 v1
TP-Link Archer C58 v1 is a dual-band AC1350 router, based on Qualcomm
QCA9561 + QCA9886. It looks like Archer C59 v1 without USB port.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 6x LED, 3x button
- UART header on PCB, RX, TX at TP4+5 (backside)

QCA9886 wlan needs pre_cal_data file and enable ieee80211 phy hotplug to
patch macaddress.

Flash instruction:

Use "factory" image directly in vendor GUI.

Recovery method:

1. Set PC to fixed ip address 192.168.0.66/24.
2. Download "lede-ar71xx-generic-archer-c58-v1-squashfs-factory.bin" and
   rename it to "tp_recovery.bin".
3. Start a tftp server with the file "tp_recovery.bin" in its root
   directory.
4. Turn off the router.
5. Press and hold Reset button.
6. Turn on router with the reset button pressed and wait ~15 seconds.
7. Release the reset button and after a short time the firmware should
   be transferred from the tftp server.
8. Wait ~30 second to complete recovery.

Flash instruction under U-Boot, using UART:

tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
erase 0x9f020000 +$filesize
cp.b $fileaddr 0x9f020000 $filesize
reset

This commit is based on GitHub PR#1112

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-06-29 10:37:36 +02:00
Mathias Kresin
e7cd6f5d66 ar71xx: add AVM FRITZ!WLAN Repeater 300E support
Specifications:
* SoC: AR7242 (Virian 400MHz)
* RAM: 64 MB DDR (W9751G6JB-25)
* Flash: 16MB SPI flash (S25FL129PIF)
* WiFi: AR9382 (2.4/5GHz) + 2x SE2595L
* LAN: 1x1000M (PEF7071V)

To install LEDE via EVA bootloader, a FTP connection need to be
established to 192.168.178.1 within the first seconds after power on:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put lede-ar71xx-generic-fritz300e-squashfs-sysupgrade.bin mtd1

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-24 22:36:38 +02:00
Ludwig Thomeczek
b4711dbad3 ar71xx: add support for TP-Link Archer C25 v1
The TP-Link Archer C25 is a low-cost dual-band router.

Specification:

- CPU: Atheros QCA9561 775 MHz
- RAM: 64 MB
- Flash: 8 MB
- Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887
- NET: 5x 10/100 Mbps Ethernet

Some LEDs are controlled by an additional 74HC595 chip.

Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
[minor code style fixes, boards alphabetical order fixes,
reworked commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:18 +02:00
Serg Studzinskii
b7cc661615 ar71xx: add support for TP-Link TL-WR942N v1
TP-Link TL-WR942N v1 is a 2.4 GHz single-band N450 router, based on
Qualcomm/Atheros QCA9561.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x USB 2.0
- 11x LED (most are controlled by 74HC595)
- 2x button
- UART header on PCB*

* Serial console is disabled in OEM non-beta firmwares and corresponding
  GPIO pins 14 and 15 are assigned to control USB1 and USB2 LEDs by
  production (non-beta) U-Boot and firmware.

Currently not working:

1. USB1 and USB2 LEDs if UART RX and TX pins are assigned to their GPIOs
   by some U-Boot versions.

Flash instruction under vendor GUI:

1. Download "lede-ar71xx-generic-tl-wr942n-v1-squashfs-factory.bin".
2. Go to WEB interface and perform usual firmware upgrade.

FLash instruction under U-Boot recovery mode (doesn't work in beta
firmware):

1. Setup PC with static IP "192.168.0.66/24" and tftp server.
2. Change "*-factory" image filename to "WR942v1_recovery.bin" and make
   it available to download from your tftp server.
3. Press "reset" button and power up the router, wait till "WPS" LED
   turns on.

Flash instruction under U-Boot, using UART (can be done only with
preinstalled UART-enabled U-Boot version!):

1. Use "tpl" to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
   tftp 0x81000000 lede-ar71xx-generic-tl-wr942n-v1-sysupgrade.bin
   erase 0x9f020000 +$filesize
   cp.b 0x81000000 0x9f020000 $filesize
   reset

Signed-off-by: Serg Studzinskii <serguzhg@gmail.com>
[minor code style fixes, extended commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:17 +02:00
Piotr Dymacz
18d5cee2a8 ar71xx: fix Wallys DR344 GPIO-connected LEDs and button
This fixes wrong GPIO numbers for LEDs and button in Wallys DR344 board
and sets color of all LEDs to green as the mass production boards have
only green one.

Actually, DR344 has 6 GPIO-connected LEDs and one button:

- GPIO11: status
- GPIO12: sig1
- GPIO13: sig2
- GPIO14: sig3
- GPIO15: sig4
- GPIO16: reset button
- GPIO17: lan

WAN LED is connected directly with AR8035 PHY.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-05-30 14:34:04 +02:00
Marty Plummer
558d86923e ar71xx: add support for EnGenius ENS202EXT
EnGenius ENS202EXT is an outdoor wireless access point with
2-port 10/100 switch, detachable antennas and proprietery PoE.

The device is based on Qualcomm/Atheros AR9341 v1.

Specifications:
- 535/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM
- 16 MB of FLASH
- UART (J1) header on PCB (unpopulated)
- 2x 10/100 Mbps Ethernet
- 2.4 GHz, up to 26dBm
- 2x external, detachable antennas
- 7x LED, 1x button

Flash instructions:

You have three options:

- Use the vendor firmware upgrade page on the web interface and give
it the factory.img. This is the easiest way to go about it.

- If you have serial access during u-boot, interrupt the normal boot
(any key before timeout) and run 'run failsafe_boot'; this will bring
you to a minimal openwrt luci image on ip 192.168.1.1 useful if you've
bricked the normal firmware.

- Use the vendor's management cli, which can be accessed via telnet
with the same credentials as the web login (default admin:admin), then
issue the following commands:

*** Hi admin, welcome to use cli(V-1.6.7) ***
---========= Commands Help =========---
      stat -- Status
       sys -- System
    wless2 -- 2.4G-Wireless
      mgmt -- Management
      tree -- Tree
      help -- Help
    reboot -- Reboot
ens202ext>mgmt
  Management
---========= Commands Help =========---
     admin -- Administration
     mvlan -- Management VLAN settings
      snmp -- SNMP settings
    backup -- Backup/Restore settings
    autorb -- Auto reboot settings
   fwgrade -- Firmware upgrade
      time -- Time settings
   wifisch -- Wifi schedule
       log -- Log
      diag -- Diagnostics
      disc -- Device Discovery
    logout -- Logout
      help -- Help
      exit -- Exit
ens202ext/mgmt>fwgrade
  Management --> Firmware upgrade
---========= Commands Help =========---
      fwup -- Firmware upgrade
      help -- Help
      exit -- Exit
ens202ext/mgmt/fwgrade>fwup http://web.server/lede-ar71xx-generic-ens202ext-squashfs-factory.bin

Signed-off-by: Marty Plummer <ntzrmtthihu777@gmail.com>
2017-05-30 14:15:25 +02:00
Andrey Polischuk
0f21873f7f ar71xx: fix LED defines for TP-Link TL-WR740N v6
Signed-off-by: Andrey Polischuk <androld.b@gmail.com>
[changed commit subject, dropped redundant kernel config symbol]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-05-30 14:15:25 +02:00
Filip Moc
a639cbfd00 ar71xx: Add support for TP-Link MR6400
You can flash via tftp recovery (serve factory image as /mr6400_tp_recovery.bin
on 192.168.0.66/24, connect to any ethernet port and power on device while
holding the reset button). Flashing via OEM web interface does not work.

Hardware Specification (v1.0 EU):
 - SoC: QCA9531
 - Flash: Winbond W25Q64FV (8MiB)
 - RAM: EtronTech EM6AB160TSE-5G (64MiB)
 - Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
 - Ethernet: 2NIC (3x100M + 1x100M)
 - WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
 - Power: DC 12V 1A

Signed-off-by: Filip Moc <lede@moc6.cz>
2017-05-27 07:54:21 +02:00
Mathias Kresin
e20965811d ar71xx: fix ath9k default LED changes fallout
Since 192f0a3db8 ("ath9k: unset the default LED pin if used by
platform leds") the default ath9k wireless LED is not set as soon as
any pin of the ath ath9k gpio controller is used.

All touched boards have leds defined which are using the gpio pins
exposed by the ath9k driver but rely on a default set wireless led
trigger.

Add the wireless leds were missing and setup the wireless phy trigger
in userspace.

Signed-off-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-13 08:18:57 +02:00
Mathias Kresin
1f5ea4eae4 ar71xx: add correct named default wireless led by using platform leds
Instead of renaming the default wireless led attached to the wireless
chip, add a new led using the platform leds with the phy0tpt trigger
set in userspace.

When switching ar71xx to device tree, the same can be done by using the
build in GPIO controller and without adding new bindings.

Drop the now unused platform code.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-08 14:30:00 +02:00
Ron Angeles
156d9255f2 ar71xx: add userspace support for Mikrotik RB2011iL
Kernel/hardware support for this board has been implemented since
Chaos Calmer. This set of patches is to get the board identified in
userland. This will allow support for things like sysupgrade,
configuring initial LED state, configuring initial switch state, etc.

Signed-off-by: Ron Angeles <ronangeles@gmail.com>
2017-04-03 12:29:07 +02:00
Piotr Dymacz
4436979c83 ar71xx: add support for P&W R602N and CPE505N
P&W (full name: Shenzhen Progress&Win Technologies) R602N (could be also
labeled as R602F, R602, etc.) is a simple N300 router with 5-port
10/100 Mbps switch, non-detachable antennas and USB.

CPE505 is an outdoor CPE with PoE support and detachable antennas.

Both devices are based on Qualcomm/Atheros QCA9531 v2.

Common specification:

- 650/597/216 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- UART (J2) header on PCB

R602N specification:

- 5x 10/100 Mbps Ethernet
- 1x USB 2.0
- 2T2R 2.4 GHz with external LNA and PA (SE2576L), up to 28 dBm
- 2x external, non-detachable antennas
- 7x LED, 1x button

CPE505N specification:

- 2x 10/100 Mbps Ethernet (both ports support passive PoE 12-24 V)
- 2T2R 2.4 GHz with external LNA and PA (SKY65174-21), up to 30 dBm
- 2x external, detachable antennas (RP-SMA connectors)
- 1x RGB LED, 2x LEDs (in RJ45 sockets), 1x button

Flash instructions:

It seems that there are many different versions of the firmware which
these devices are shipped with. The generic/standard one is based on
some modified OpenWrt and LEDE firmware can be flashed directly from
vendor's webgui or with sysupgrade (root password is "admin123").

Before flashing, make sure (use "fw_printenv") that the kernel load
address in your device is set to "0x9f050000" (bootcmd variable is
"bootm 0x9f050000"). If your device uses different load address, you
should first change it, under vendor's firmware, with command:

fw_setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS"

Where OLD_ADDRESS is previous kernel load address (in CPE505 version
I got access to, it was "0x9fe80000"). This will allow you to use
both the vendor's and LEDE firmware.

If version of your device contains empty U-Boot environment (you will
get information about this after issuing "fw_printenv"), you should
use U-Boot, serial line access and TFTP to perform firmware upgrade:

1. tftp 0x80060000 lede-ar71xx-generic-...-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS"
5. saveenv && reset

These devices contain also web recovery mode inside U-Boot. It can be
started with pressing the reset button for around 3 seconds just after
the device powerup. Web recovery panel is available on "192.168.10.9"
and to be able to use it, IP on your PC must be set to "192.168.10.10".

Make sure to change kernel load address before using recovery mode or
the U-Boot will not be able to load LEDE firmware.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-23 17:59:47 +01:00
Vaclav Svoboda
0d9adb4832 ar71xx: add support for TP-LINK TL-WR840N v2 and v3
This patch adds support for the TP-LINK TL-WR840N v2 and v3.

- SoC: Qualcomm QCA9533-BL3A (650 MHz)
- RAM: 32 MiB (Zentel A3S56D40GTP)
- Flash: 4 MiB
   (v2: Macronix MX 25L323F)
   (v3: Winbond 25Q32FVSIG)
- LAN: 4x 100M
- WAN: 1x 100M

Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
2017-03-23 09:41:15 +01:00
Ryan Mounce
978998628f ar71xx: add support for MikroTik hAP ac
This patch adds initial support for the MikroTik RouterBOARD hAP ac
(RB962UiGS-5HacT2HnT).

All functions are supported except:
-SFP cage (eth1) is not working
-WLAN LEDs are not working

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
2017-03-23 09:35:14 +01:00
Ryan Mounce
540edf7045 ar71xx: add support for MikroTik hAP ac lite
This patch adds support for the MikroTik RouterBOARD hAP ac lite
(RB952Ui-5ac2nD).

The hAP ac lite is nearly identical to the hAP, with an added QCA9887
5GHz radio. The 2.4GHz radio ID is also changed in the hAP ac lite.

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
2017-03-23 09:35:14 +01:00
Thibaut VARENE
e3dc036cbf ar71xx: add support for RB LHG 5nD
This patch adds support for the MikroTik RouterBOARD LHG 5
https://routerboard.com/RBLHG-5nD

Specifications:
- SoC: Atheros AR9344 (600MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Wireless: builtin AR9344 5GHz, 2x2:2
- Ethernet: 1x100M

Initial flash via initramfs, like all other RB devices.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-03-15 23:00:52 +01:00
Shuanglin Liu
53ef20f65a ar71xx: add support for Rockeetech AP531B0
Specification:
- SoC: Qualcomm Atheros QCA9531 (650/400/216 MHz (CPU/DDR/AHB))
- RAM: 64 MiB DDR2
- Storage: 16 MiB of flash (optional 16 MiB second flash)
- Wireless: built into QCA9531 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0) 1x100M (port 4)
- PCI-E: x1
- SIMcard slot: x1
- USB 2.0 port: x1 (optional)
- Ext GPIO pin: x8
- UART for serial console: x1
- External watchdog: x1 (optional)
- Power supply: 9-48V (DC jack/passive PoE)

Installation through tftp:
- Copy <Firmware Image Name> into tftp directory
- Connect board via ttl port and Ethernet port
- Boot the AP531B0
- When "Autobooting in 1 seconds" appears press Enter
- Set serverip and ipaddr appropriate
  (e.g. setenv serverip 192.168.88.10;setenv ipaddr 192.168.88.1)
- Enter "tftp 0x8050000 <Firmware Image Name>"
- Enter "erase 0x9f050000 +$filesize"
- Enter "cp.b 0x80500000 0x9f050000 $filesize"
- Enter "reset"

Signed-off-by: Shuanglin Liu <roboidler@gmail.com>
2017-03-12 17:38:31 +01:00
Wojciech Jowsa
f223c4a923 ar71xx: set status led for the gl-* boards
Signed-off-by: Wojciech Jowsa <w.jowsa@radytek.com>
2017-03-06 07:50:11 +01:00
Thomas Roberts
f9278337cf ar71xx: add support for TL-WR802N Version 2
This patch adds support for the TP-Link TL-WR802N Version 2.

Specification:
- SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc)
- RAM: 32 MiB
- Storage: 4 MiB of FLash on board
- Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0)

Installation through OEM Web Interface:
- Connect to TL-WR802N by Ethernet or Wi-Fi
- Go to http://192.168.0.1 (default user is "admin" & password is "admin)
- Go to "System Tools -> Firmware Upgrade"
- Browse for firmware "*.factory-us.bin" or  "*.factory-eu.bin" for eu model
- Click upgrade

Installation through tftp:
Note: T_OUT, T_IN and GND on the board must be connected to USB TTL
      Serial Configuration 115200 8n1

- Boot the TL-WR802N
- When "Autobooting in 1 seconds" appears type "tpl" followed by enter
- Connect to the board Ethernet port
    (IPADDR: 192.168.1.1, ServerIP: 192.168.1.10)
- tftpboot 0x80000000 <Firmware Image Name>
- Record the result of "printenv bootcmd"
- Enter "erase <Result of 'printenv bootcmd'> +0x3c0000"
    (e.g erase 0x9f020000 +0x3c0000)
- Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000"
    (e.g cp.b 0x80000000 0x9f020000 0x3c0000)
- Enter "bootm <Result of 'printenv bootcmd'>"
    (e.g bootm 0x9f020000)

Signed-off-by: Thomas Roberts <tom.p.roberts@gmail.com>
2017-02-20 09:10:17 +01:00
Henryk Heisig
d6baeb5c48 ar71xx: fix lan ports on archer C59 and C60
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-02-17 10:30:48 +01:00
Thibaut VARENE
b2044a7f60 ar71xx: add support for RB750r2
This patch adds support for the MikroTik RouterBOARD hEX lite
https://routerboard.com/RB750r2

Specifications:
- SoC: Qualcomm QCA9531 (850MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Ethernet: 5x100M (1 PoE in)

This ethernet router is based on the same platform as the hEX PoE lite (it
shares the same board identifier), but has no USB and no PoE out.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:58 +01:00
Thibaut VARENE
19f42663d2 ar71xx: add support for RB750UPr2
This patch adds support for the MikroTik RouterBOARD hEX PoE lite
https://routerboard.com/RB750UPr2

Specifications:
- SoC: Qualcomm QCA9531 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Ethernet: 5x100M (1 PoE in, 1 PoE out)
- USB: Type A

This ethernet router is based on the same platform as the wireless router hAP.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:58 +01:00
Thibaut VARENE
8cbb2ac633 ar71xx: add support for RB951Ui-2nD
This patch adds support for the MikroTik RouterBOARD hAP
https://routerboard.com/RB951Ui-2nD

Specifications:
- SoC: Qualcomm QCA9531 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Wireless: builtin QCA9531, 2x2:2
- Ethernet: 5x100M (1 PoE in, 1 PoE out)
- USB: Type A

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:58 +01:00
Thibaut VARENE
b18bae37a4 ar71xx: provide support for RB-941-2nD via mach-rbspi.c
This patch implements support for the hAP lite in mach-rbspi.c

hAP lite was supported via mach-rb941.c, so this file is removed
as well as the corresponding build bits.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:57 +01:00
Thibaut VARENE
c59fa94eee ar71xx: add support for RB mAP L-2nD
This patch adds support for the MikroTik RouterBOARD mAP lite
https://routerboard.com/RBmAPL-2nD

Specifications:
- SoC: Qualcomm QCA9533 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Wireless: builtin QCA9533, 2x2:2
- Ethernet: 1x100M

This is another 16M SPI NOR mikrotik device. The machine file is named
mach-rbspi.c because I plan to add support for several of the other spi-based
RouterBOARD devices in subsequent patches: they share most of the hardware
and thus the same codebase.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:57 +01:00
Alexandru Gagniuc
6cce9557a0 ar71xx: Add support for D-Link EBR-2310 Rev. C
Add support for the EBR-2310, which is almost identical to the DIR-615
rev E4, without the wifi.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2017-02-14 12:27:14 +01:00
Piotr Dymacz
56561b9f51 ar71xx: add support for TP-Link TL-WA850RE v2
TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.

Short specification:

- 550/391/195 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x internal antennas (embedded on PCB)
- 9x LED (all can be turned off with GPIO15), 2x button
- UART (J3) header on PCB

Flash instruction: use "factory" image directly in vendor GUI.

Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.

You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin

Image was tested only in US version of the device, but should work
also with the same device version sold in other countries.

Available FLASH space, with LEDE trunk, is only 240 KB.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-02-14 12:25:33 +01:00
Sven Eckelmann
640f9158e2 ar71xx: add user-space support for the OpenMesh A40
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann
174605c467 ar71xx: add user-space support for the OpenMesh A60
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann
bdfe4c1218 ar71xx: add user-space support for the OpenMesh OM2Pv4/-HSv4
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:04 +01:00
Henryk Heisig
e39dc8d823 ar71xx: add support to TP-Link Archer C59v1 and C60v1
TP-Link Archer C59v1 is a dual-band AC1350 router, based on Qualcomm/Atheros
QCA9561+QCA9886.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- 8x LED (controled by 74HC595), 3x button
- UART header on PCB

TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros
QCA9561+QCA9886.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB

Currently not working:
- Port LAN1 on C59, LAN4 on C60
- WiFi 5GHz (missing ath10k firmware for QCA9886 chip)
- Update from oficial web interface ( tplink-saveloader not support "product-info")

Flash instruction:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-cXX-v1-squashfs-factory.bin
and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Flash instruction under U-Boot, using UART:

1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. reset

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[Jo-Philipp Wich: remove duplicate ATH79_MACH_ARCHER_C59/C60_V1 entries]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-01-26 11:38:21 +01:00
YuheiOKAWA
261415a660 ar71xx: add support for PQI Air Pen
SoC: AR9331
Ethernet x1, Wireless 2.4G, uSD card slot x1.
USB Power, include Li-Po Battery.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

Changes in v2:
alphabetical ordering, tabs fron spaces.
2017-01-20 00:52:48 +01:00
Conor O'Gorman
274546046d ar71xx: add Abicom SC1750 support
Support Abicom International Scorpion SC1750 Board

QCA9550 700MHz Extended Temperature Range
256MB DDR2
256MB Nand Flash
16MB Nor Flash
1x SFP, 1x PCIe
2x 10/100/1000 Ethernet
135x100 mm
802.11ng/g/b
802.11ac/an/a

Signed-off-by: Conor O'Gorman <i@conorogorman.net>
2017-01-20 00:40:40 +01:00
Conor O'Gorman
d38ffd8cd9 ar71xx: add Abicom SC450 support
Support Abicom International Scorpion SC450 Board

QCA9550 700MHz Extended Temperature Range
256MB DDR2
256MB NAND Flash
16MB NOR Flash
10/100/1000 Ethernet
15W Max, 3x3 Mode, Full Power TX Power
802.3-at POE+ & DC Input options
100x 85mm
USB
PCIe
SFP
GPIO/LED

Signed-off-by: Conor O'Gorman <i@conorogorman.net>
2017-01-20 00:40:33 +01:00
Conor O'Gorman
eb97f41fc2 ar71xx: add Abicom SC300M support
Support Abicom International Scorpion SC300M Module

QCA9550 700MHz Extended Temperature Range
256MB DDR2
256MB Nand Flash
16MB SPI Flash
802.11a/na/b/g/ng
GPIO x 22, USB x2, PCIe x2
10/100/1000 Ethernet
23dBm, Optional Onboard Antenna
DC Input, 8-20V DC
85 x 55 mm

Signed-off-by: Conor O'Gorman <i@conorogorman.net>
2017-01-20 00:40:27 +01:00
Thibaut VARENE
3f7841a70a ar71xx: add support for RB-941-2nD
Add full support for Mikrotik RB-941-2nD (hAP lite)

Original patch by Sergey Sergeev <adron@yapic.net> and
more information is available here:
https://wiki.openwrt.org/toh/mikrotik/rb941_2nd
I updated and adapted the patch to apply cleanly to LEDE trunk
and added proper numbering for the switch ports (matching case
labels).
Tested working on actual hardware with the information
provided in the above webpage. Sysupgrade works.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-16 20:40:12 +01:00
Matthias Schiffer
1fef80f29c
ar71xx: add support for TP-Link WBS210/510
The devices are mostly identical to the CPE210/510, but use external
antennas.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-01-05 16:01:17 +01:00
Tal Keren
9c475eca3e ar71xx: add support for TP-Link RE450
Add full support for TP-Link RE450.
The wireless SoC is similiar to Archer C7: QCA9558 + QCA9880 (pci).
The ethernet interface is AR8035, but the mdio is connected to the gpio and
the chipset builtin mdio bus isn't used, which is unique (and weird), so the
kernel gpio mdio module is used.
The two ethernet leds are connected to the GPIO, so they are both configured,
one to indicate link status and the other to indicate data transfer.

The generation of the image was added to the image Makefile.
The return value of tplink-safeloader is not ignored anymore (to fail on error)

The result factory image is flashable from the stock web ui.

Signed-off-by: Tal Keren <kooolk@gmail.com>
[rd@radekdostal.com: ar71xx: RE450: do not build RE450 for nand]
Signed-off-by: Radek Dostál <rd@radekdostal.com>
[hyniu@o2.pl: ar71xx: RE450: Renaming LED accordance with the standard]
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[jo@mein.io: squash fixes from Radek and Henryk into original commit]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-12-22 14:50:05 +01:00
Ludwig Thomeczek
1a4d07c2c5
ar71xx: add support for TP-LINK WR1043ND v4
Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
2016-12-20 14:38:48 +01:00
David Lutz
aada15af93
ar71xx: add support for TP-LINK TL-WR940N v4
Signed-off-by: David Lutz <kpanic@hirnduenger.de>
2016-12-16 11:12:46 +01:00
Felix Fietkau
30285facbe ar71xx: remove AP113 reference design board support
Due to flash size limitations, support for this board has not been
functional for years

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-12 10:22:18 +01:00
Piotr Dymacz
c198ca682c ar71xx: add support for YunCore SR3200 and XD3200
YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros
QCA9563+QCA9882+QCA8337N.

YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount
AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334.

Common specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB or RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm
- 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm

SR3200 specification:

- 5x 10/100/1000 Mbps Ethernet
- 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips)
- 3x LED (+ 5x LED in RJ45 sockets), 1x button
- UART header on PCB

XD3200 specification:

- 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port)
- 4x internal antennas
- 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button
- UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB

LED for 5 GHz WLAN is currently not supported on both devices as it is
connected directly to the QCA9882 radio chip.

Flash instruction under vendor firmware, using telnet/SSH:

1. If your firmware does not have root password, go to point 5
2. Connect PC with 192.168.1.x address to LAN or WAN port
3. Power up device, enter failsafe mode with button (no LED indicator!)
4. Change root password and reboot (mount_root, passwd ..., reboot -f)
5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP
6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
7. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
- mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware

Flash instruction under U-Boot, using UART:

1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
5. saveenv && reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-12-12 09:57:40 +01:00
Matthias Schiffer
9c5af2489a
ar71xx: fix LEDs and sysupgrade support for TL-WA801ND v3
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-12-06 19:08:35 +01:00
Piotr Dymacz
e33dcd1cfe ar71xx: add support for YunCore CPE830
CPE830 is a clone of AP90Q, with different type of antenna (panel)
and additional 4 LEDs for WiFi signal level indication.

Use the same flash approach as for YunCore AP90Q.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
eb9ba2b91e ar71xx: add support for YunCore CPE870
YunCore CPE870 is an outdoor CPE/AP based on Atheros AR9341.
Short specification:

- 535/400/200 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, passive PoE support
- 64/128 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz with external PA (SKY65174-21), up to 30 dBm
- internal 14 dBi panel antenna
- 8x LED, 1x button
- UART (JP1) header on PCB

Flash instruction (do it under U-Boot, using UART):

1. tftp 0x80060000 lede-ar71xx-generic-cpe870-squashfs-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. setenv bootcmd "bootm 0x9f020000"
5. saveenv && reset

Vendor firmware access (login/password): Admin/5up

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
01dda0659e ar71xx: add support for YunCore AP90Q
YunCore AP90Q is an outdoor CPE/AP based on Qualcomm/Atheros QCA9531 v2.
Short specification:

- 650/600/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, passive PoE support
- 64/128 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz with external PA, up to 29 dBm
- 2x internal 5 dBi omni antennas
- 4x LED, 1x button
- UART (JP1) header on PCB

Flash instruction under U-Boot, using UART:

1. tftp 0x80060000 lede-ar71xx-generic-ap90q-squashfs-sysupgrade
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset

Flash instruction under vendor fimrware, using telnet/SSH:

1. Connect PC with 192.168.1.x address to WAN port
2. Power up device, enter failsafe mode with button (no LED indicator!)
3. Change root password and reboot (mount_root, passwd ..., reboot -f)
4. Upload lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin to /tmp using SCP
5. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
6. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9f050000"
- mtd erase firmware
- mtd -r write lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin firmware

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
16afa08d19 ar71xx: add support for COMFAST CF-E380AC v1 and v2
COMFAST CF-E380AC v1/v2 is a ceiling mount AP with PoE
support, based on Qualcomm/Atheros QCA9558+QCA9880+AR8035.

There are two versions of this model, with different RAM
and U-Boot mtd partition sizes:
- v1: 128 MB of RAM, 128 KB U-Boot image size
- v2: 256 MB of RAM, 256 KB U-Boot image size

Version number is available only inside vendor GUI,
hardware and markings are the same.

Short specification:

- 720/600/200 MHz (CPU/DDR/AHB)
- 1x 10/100/1000 Mbps Ethernet, with PoE support
- 128 or 256 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz, with external PA (SE2576L), up to 28 dBm
- 3T3R 5 GHz, with external PA (SE5003L1), up to 30 dBm
- 6x internal antennas
- 1x RGB LED, 1x button
- UART (T11), LEDs/GPIO (J7) and USB (T12) headers on PCB
- external watchdog (Pericon Technology PT7A7514)

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
31952dbd1c ar71xx: add support for COMFAST CF-E320N v2 and CF-E520N/CF-E530N
As we already have support for CF-E316N v2 and many devices from
this vendor look similar, the support was included in existing
mach-*.c file, with few cleanups and fixes.

All 3 devices are based on Qualcomm/Atheros QCA9531 v2.

COMFAST CF-E320N v2 is a ceiling mount AP with PoE support.
Short specification:

- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x RGB LED, 1x button
- UART (J1), GPIO (J9) and USB (J2) headers on PCB
- external watchdog (Pericon Technology PT7A7514)

COMFAST CF-E520N/CF-E530N are in-wall APs with USB and PoE support.
They seem to have different only the front panel.
Short specification:

- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, WAN with PoE support
- 1x USB 2.0 (in CF-E520N covered by panel, available on PCB)
- 32 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x LED, 1x button
- UART (J1) headers on PCB

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Jaylin Yu
7ee6ab1a31 ar71xx: Add usable, inactive LEDs on OpenMesh devices
OpenMesh devices have often LEDs which are not yet used by OpenWrt. These
should still be available as disabled LEDs in the system configuration for
easier modification.

Signed-off-by: Jaylin Yu <jaylin.yu@open-mesh.com>
[sven.eckelmann@open-mesh.com: Remove LEDs already specified via diag.sh,
 add wifi/status LEDs]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-11-16 10:54:33 +01:00
FUKAUMI Naoki
0165203304 ar71xx: add support for Buffalo BHR-4GRV2
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
2016-11-16 10:54:33 +01:00