Commit graph

1743 commits

Author SHA1 Message Date
Hauke Mehrtens
5b089e45a6 kernel: update 4.4 kernel to 4.4.42
Refresh patches on all 4.4 supported platforms.
Compile & run tested: lantiq/xrx200

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-01-13 23:05:36 +01:00
Yo Abe
29097b95ba ramips: fix WLI-TX4-AG300N boot and network
Partition label "linux" prevents the root file system to be mounted at
boot time leading to a kernel panic. After changing it to "firmware",
the 2 uimage partitions "kernel", "rootfs" and squashfs "rootfs_data"
are correctly recognized.

The attached IP175C 10/100 MBit switch cannot connect to a link with
fixed 1000Mbit speed. The correct link speed is 100MBit. The switch
is detected and can be configured via mdio bus and should allow two
separable VLANs to be configured for the 4 available ports.

Signed-off-by: Yo Abe <abe.geel@gmail.com>
[picked from openwrt/PR#330]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-01-13 08:32:35 +01:00
Andrew Yong
3f31029b19 ramips: add support for VoCore2
This patch adds support for the VoCore VoCore2 and its complementary
"ultimate" dock.

Specifications:
- SoC: MediaTek MT7628AN (580MHz, ramips)
- RAM: 128MB DDR2 166MHz
- Storage: 16MB NOR SPI flash onboard + microSD slot on dock
- Wireless: Built into MT7628AN (mt76) with 1T1R firmware on VoCore2
            boards with onboard 1x chip antenna
- Ethernet: 1x100M (port0) on dock, 1x100M (port2) on PCB header
- Dock hardware:
  - USB 2.0 socket
  - MicroSD socket
  - 100Mbps Ethernet x1
  - 3.5mm headphone jack (TRRS) connected to Everest Semi ES8388 I2S
    DAC/ADC (support WIP)
  - Micro USB for power and console (UART2)

Initial installation:
- VoCore2 comes preinstalled with a fork of OpenWrt CC and AP on
  SSID "VoCore2"
- Connect to VoCore2 by Ethernet or Wi-Fi
- `ssh root@192.168.1.1` (password is "vocore")
- scp/wget/etc. LEDE sysupgrade.bin to VoCore2
- `sysupgrade -n <your image>.bin` (don't keep old config, as the
  original firmware uses Ralink SDK Wi-Fi drivers and not
  mt76+mac80211)
- after sysupgrade completes, Wi-Fi will be disabled by default so use
  Ethernet or the micro USB console to configure Wi-Fi again

Signed-off-by: Andrew Yong <me@ndoo.sg>
2017-01-13 08:32:35 +01:00
Daniel Golle
287283e6e3 ramips: rt3883: fix typo in pinctrl lna_g_func
Spotted by forum users
https://forum.openwrt.org/viewtopic.php?pid=347439#p347439

Reported-by: Tom Psyborg <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-01-13 05:44:06 +01:00
Antonis Kanouras
f2b6412c72 ramips: Fix VLAN limits for MT7621 GSW
Without this patch swconfig will only allow setting up a total of 16
VLANs, with VLAN ID range of 0-15.

Tested on ubnt-erx.

Signed-off-by: Antonis Kanouras <antonis@metadosis.eu>
2017-01-10 08:18:15 +01:00
Felix Fietkau
018d80007e kernel: remove ubifs xz decompression support
It has been unused, and less useful than squashfs for cases where flash
space usage matters.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-09 14:07:06 +01:00
Hauke Mehrtens
88ca6390ea kernel: bump to 4.4.40
Refresh patches on all 4.4 supported platforms.
Compile & run tested: lantiq/xrx200

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-01-06 19:38:55 +01:00
Felix Fietkau
84bd74057f build: use mkhash to replace various quirky md5sum/openssl calls
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-05 11:09:12 +01:00
Victor Shyba
d6c831e0e5 generic: mtd: backport SPI_NOR_HAS_LOCK
This flag was added to 4.9 with upstream commit
76a4707de5e18dc32d9cb4e990686140c5664a15.

Signed-off-by: Victor Shyba <victor1984@riseup.net>
[refresh and adjust platform patches, fix commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-01-03 19:58:00 +01:00
L. D. Pinney
b28e94d4bf ramips: MiWiFi Nano fixes
Use the the dt-bindings macros and add the reset button.

Set the correct polarity for the LEDs and drop the default state.
Remove all trigger for the LEDs. According to the manual the LEDs are
only used to show the operation state, where blue means normal
operation.

Use the MAC-Addresses stored in EEPROM for the ethernet and the
wireless interface.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
[use leds only for boot status indication, add proper commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-01-02 19:16:54 +01:00
Rafał Miłecki
939ef157da ramips: fix NixcoreX1 profiles
There was a typo in Makefile that prevented using these profiles.

Fixes: a75ce960ac ("ramips: use different board names for variants")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-12-28 23:05:24 +01:00
Mathias Kresin
0cf581ca3a ramips: use new image build code for more devices
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Mathias Kresin
a75ce960ac ramips: use different board names for variants
Use different names for flash size related board variants, to make sure
that only images for the actual flash size are considered as valid by
the image validation code.

Remove the flash size suffix from the string returned by
ramips_board_detect() to ensure that existing scripts relying on the
former used boardname are still working.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Mathias Kresin
29f5e643ad ramips: sort rt305x image file alphabetical
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Mathias Kresin
d2b1148e75 ramips: use D-Link DIR-600 B1 image for B2 version
Everything set for the B1 is identical to the values uses for the B2
version.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Mathias Kresin
d2b6bf1416 ramips: fix image validation errors
The name from the Device define will be used in the metadata. Due to
typos/different spelling, this name might not match the one exported in
/lib/ramips.sh.

Fix all name mismatches which were found by checking if the name used
in the metadata exists in /lib/ramips.sh.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Mathias Kresin
ae3ac76e56 ramips: use destinct 11AC NAS board name
Use a distinct board name even if the board is near to identical to
the WeVO W2914NS v2.

To make sure that a 11AC NAS image can not be installed on a
WeVO W2914NS v2, both board need to use different names.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Henryk Heisig
4f033b2da6 ramips: fix tplink image building fix sysupgrade firmware on MR200
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-12-24 06:52:12 +01:00
Henryk Heisig
3a6353d910 ramips: enablemodem: move /lib/ramips.sh to start()
Fix build error: /etc/init.d/enablemodem: line 2: /lib/ramips.sh: No such file or directory

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-12-24 06:51:59 +01:00
Henryk Heisig
c8043137bb ramips: Add support to TP-Link Archer MR200
CPU: MT7620N 580MHz
Flash: 8MB
RAM: 64MB
build-in modem 3G/4G
four ethernet port 10/100Mbps

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-12-22 15:03:30 +01:00
Vitaly Chekryzhev
190ee7d86b ramips: add support for ZyXEL Keenetic Omni / Omni II
Factory image can be installed via Zyxel WebUI.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
2016-12-22 15:03:13 +01:00
Giuseppe Lippolis
96a7ee3c80 ramips: adding registration for si3210
The si3210 is a SLIC device providing a complete analog telephone
interface and therefore frequently used in soho router.
The si3210 have a native spi interface to be controlled by the CPU
but currently there is no dedicated driver in lede.
Adding a registration for this device in spidev allow to control the
device in user space.
This way of patching is also in line with the rationale of the spidev
driver, see: http://marc.info/?t=148145791900001&r=1&w=2
The si3210 has been also added in the DWR-512 DT to properly describe
the HW.

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2016-12-20 09:35:37 +01:00
Kevin Darbyshire-Bryant
79abb8f140 kernel: bump to 4.4.39
Bump & refresh patches for all 4.4 targets.

Compile & run tested: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
2016-12-20 09:35:36 +01:00
L. D. Pinney
02ca833f04 ramips: WNDR3700v5 fix mtd partitions and radios
Fix the mtd partition layout and enable both radios in the dts

Tested-by Andrius Štikonas <andrius@stikonas.eu>
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
2016-12-20 09:35:35 +01:00
Giuseppe Lippolis
132b88ea39 ramips: adding DWM-158 3g Modem
This patch add the 3G modem DWM-158 to the usb-serial option driver.
The DWM-158 is a pcie 3G modem. It is embedded in the DWR-512 modem
supportet by lede. The patch has been submitted and merged in the upstream
linux-next repository.

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2016-12-14 10:37:01 +01:00
BangLang Huang
960c477432 ramips: Fix led init script for Lenovo Y1/Y1s
This commit fix the led init script for Lenovo Y1 and
Y1S due to the manual and dts file.

Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
2016-12-04 15:51:18 +01:00
Felix Fietkau
566de813c3 ramips: prevent packet forwarding on mt7620 between switch ports during init (FS#103)
By default, forwarding between all ports is allowed on init. This is
problematic in cases where some ports are supposed to be isolated from
each other, most commonly LAN/WAN separation.

REG_ESW_PORT_PCR(port) has a destination mask for a particular port,
controlling what other ports it is allowed to send packets to.
Instead of initializing all to 0xff (all ports), allow each physical
port to send to the CPU port, and the CPU port to send to all other
ports.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-04 11:41:49 +01:00
Yong-hyu, Ban
377eac0ceb ramips: fix LAN port order of WeVO W2914NS v2
Signed-off-by: Yong-hyu, Ban <perillamint@gentoo.moe>
2016-12-04 08:22:07 +01:00
BangLang Huang
23b58f8acb ramips: fix PBR-D1 button definition
Due to the product specification, the button on PBR-D1 should be
reset, not wps.

Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
2016-12-04 07:03:17 +01:00
Tobias Wolf
2e020e2cef ramips: add support for PCI based OHCI/EHCI support for F5D8235 V1
This router uses an PCI attached NEC EHCI controller to support the single USB port.

Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
2016-12-04 07:03:17 +01:00
Tobias Wolf
13c0d208b2 ramips: introduce CONFIG_PCI and CONFIG_OF_*PCI for rt288x
This is a prerequisite for F5D8235 V1 to use PCI based OHCI/EHCI.

Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
2016-12-04 07:03:17 +01:00
Tobias Wolf
c2ed721e89 ramips: improve F5D8235 V1 support
This fixes the partition name for the firmware splitter, the cfi
address and adds the mtd-eeprom address for wmac. It adds additional
LEDs and make use of them in diag.sh and 01_leds.

Please note that the ":blue:wired" LED is used because the
":blue:router" behaviour is unpredictable for failsafe indication. The
issue with the router LED is that you have two states only.
"off" is steady on and "on" blinks. Therefore the wired LED is more
suitable.

Furthermore it reuses the correct switch configuration definition to
reflect the device ports and numbering. Additionally fixes the issue
that the default configuration is not applied as no port 6 exists on
this device.

Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
2016-12-04 07:03:17 +01:00
John Crispin
7c809f1687 ramips: fix sdhci support on mt7621
the IRQ level was wrong. refresh the patch while at it.

Signed-off-by: John Crispin <john@phrozen.org>
2016-12-01 18:30:41 +01:00
Andrew Yong
07b571a435 ramips: RB750Gr3: Add pwr LED and buzzer to DTS
use pwr LED in diag.sh
Expose unused pinmux pins as GPIOs
export power LED and buzzer pins
Use rb750gr3:blue:pwr LED in diag.sh for boot status instead of rb750gr3:green:usr

Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-12-01 16:17:55 +01:00
Mathias Kresin
18c64f41c7 treewide: fix button keys codes used in dts
Use keycodes that matches the intended use case based on the label.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-27 15:34:23 +01:00
Mathias Kresin
4780e7e994 ramips: add size checks/append metadata where missing
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-27 15:34:23 +01:00
Mathias Kresin
6cc0ae27b9 ramips: fix Airlink AR670W factory image
Move the mkwrgimg build step to the makefile. It will be required by
other boards as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-27 15:34:23 +01:00
Yong-hyu, Ban
c723646f22 ramips: Add missing chunked-io directive to W2914NSV2.dtsi
Fix bug that LEDE failed to boot with this message:

WARNING: CPU: 2 PID: 1 at drivers/spi/spi-mt7621.c:214
mt7621_spi_transfer_one_message+0x28c/0x620()

Signed-off-by: Yong-hyu, Ban <perillamint@gentoo.moe>
2016-11-26 22:39:21 +01:00
Andrew Yong
a7de18718d ramips: SamKnows SK-WB8 DTS cleanup
Use gpio.h definition of GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW. Remove unused backup partition to increase available JFFS space. As long as U-Boot env variable "bootcount" is < 3 (reset to 0 after boot by init script) SamKnow's U-Boot will not attempt to boot from the backup flash address (0xe30000).

Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-11-26 22:35:52 +01:00
Mathias Kresin
ee6beb2e1c ramips: remove kmod-ledtrig-usbdev from recently added devices
None of the devices uses an usb led at all.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-24 22:37:40 +01:00
Giuseppe Lippolis
ec1de9b1a6 ramips: Add device DLINK DWR-512-B
The Dlink DWR-512-B modem is a ralink 5350 processor based embedding
a 3G mini-pcie router.

The oem JBOOT bootloader has to be replaced by a RT5350 SDK
U-Boot such as https://github.com/stevenylai/ralink_sdk - U-Boot
configured for the RT5350 256MiB SDR.

Main reason to change the bootloader is the encrypted header used to
store the kernel image. In this way an image can only be generated
using the propietary binboy tool (included in the GPL distribution
from Dlink). The binboy tool doesn't allow to modify the kernel/rootfs
partition scheme. This is considered a big constraint (limited kernel
size and inefficient usage of flash space).

For interested people I pubblished the details of my investigation
about the encrypted firmware header here:
http://lists.infradead.org/pipermail/lede-dev/2016-October/003435.html

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2016-11-23 08:36:11 +01:00
Mathias Kresin
8f561c6516 ramips: do not append metadata to CY-SWR1100 factory image
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-23 08:36:11 +01:00
Mathias Kresin
f1d0eba3ea ramips: cleanup dts files of mt7621 based boards
Fix a typo in mt7621.dtsi compatible string. Disable spi, sdhci and pci
in mt7621.dtsi and enable the nodes in the indiviual board dts files.
The nodes require further device specific configuration anyway.

Remove the m25p80@0 spi child node from mt7621.dtsi and add the
chunked-io parameter to the individual board dts files. Fix the spi
flash compatible string for the WNDR3700V5.

Drop the mt7621-eval-board compatible string for all boards which are
not the eval board.

Drop the linux,modalias parameter from spi flash node.

Remove the xhci node from board files, it is already enabled in dtsi.
Disable xhci for boards not having usb ports populated.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-23 08:36:10 +01:00
Mathias Kresin
18e7f49975 ramips: order mt7621.mk alphabetical
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-23 07:09:03 +01:00
Andrew Yong
fe43d90d93 ramips: fix wrong check for MT7621AT
fix in sdhci Use ralink_soc == MT762X_SOC_MT7621AT instead of CONFIG_SOC_MT7621 which is
wrong and breaks builds on mt7620a-similar platforms (MT7621, MT7688)

Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-11-21 16:49:54 +01:00
Andrew Yong
605cab749e ramips: Fix sdhci kernel panics on MT7621
Enable work-arounds present in the code commented-out but needed to write to
sdcard on mt7621 which currently causes kernel to oops when engaging in
serious writing to sdcard. With this change applied, there are still
occasional warnings thrown by the mmc driver, however, at least it no longer
crashes the system and even large writes (full-card dump/erase/write/compare)
don't show any corruption.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

Rebase to LEDE and added "CONFIG_SOC_MT7621" check to ensure non-MT7621 devices do not face performance regressions.
Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-11-21 12:31:39 +01:00
perillamint
68634426fe ramips: add support for WeVO W2914NS v2
Signed-off-by: Yong-hyu Ban <perillamint@gentoo.moe>
2016-11-21 10:13:17 +01:00
Felix Fietkau
478f1f6b16 ramips: append metadata to images
metadata checks are not enforced yet, because some images are still
being built by legacy code

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-19 11:24:10 +01:00
Vitaly Chekryzhev
348344874c ramips: add support for ZyXEL Keenetic Viva
Factory image can be installed via Zyxel WebUI.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
[removed linux,modalias parameter from flash node in dts]
[removed sdhci node from dts; no sd card slot here]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-18 08:54:57 +01:00
Vitaly Chekryzhev
5f38d1ad85 ramips: add MT7620 MIB support for switch and port
Move definitions to header. Replace array size definitions with macro.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
[merged into 0513-net-mediatek-add-swconfig-driver-for-gsw_mt762x.patch]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: John Crispin <john@phrozen.org>
2016-11-17 20:01:21 +01:00