GL.iNet GL-USB150 is an USB dongle WiFi router, based on Atheros AR9331.
Specification:
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- Realtek RTL8152B USB to Ethernet bridge (connected with AR9331 PHY4)
- 1T1R 2.4 GHz
- 2x LED, 1x button
- UART header on PCB
Flash instruction:
Vendor firmware is based on OpenWrt CC. GUI or sysupgrade can be used
to flash LEDE firmware.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ifname variable were not assigned due to syntax error
causing the hostapd config file to have an empty iapp_interface= option
Signed-off-by: Lorenzo Santina <lorenzo.santina.dev@gmail.com>
For the Archer C50v1, the EU and US versions are differentiated by their
respective HW additional version (0x0 for US, 0x2 for EU).
The stock web interface checks this field before flashing, making it
impossible to flash the current (US) factory image on EU hardware.
However the bootloader does not check this field, making it possible to use
a single sysupgrade image for both hardware.
This patch adds the necessary build bits to generate both EU and US factory
images, and renames the target as "Archer C50v1" since there are as of now
3 different versions of Archer C50 (all with different CPUs).
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
The HNET C108
(http://www.szhwtech88.com/Product-product-cid-100-id-4374.html) is a
mifi based on MT7602A, which has the following specifications:
* CPU: MT7620A
* 1x 10/100Mbps Ethernet.
* 16 MB Flash.
* 64 MB RAM.
* 1x USB 2.0 port. Only power is connected, this port is meant for
charging other devices.
* 1x mini-PCIe slots.
* 1x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x button.
* 6000 mAh battery.
* 5x controllable LEDs.
Works:
* Wifi.
* Switch.
* mini-PCIe slot. Only tested with a USB device (a modem).
* SIM slot.
* Sysupgrade.
* Button (reset).
Not working (also applies to the factory firmware):
* Wifi LED. It is always switched on, there is no relation to the
up/down state or activity of the wireless interface.
Not tested:
* SD card reader.
Notes:
* The C108 has no dedicated status LED. I therefore set the LAN LED as
status LED.
Installation:
The router comes pre-installed with OpenWRT, including a variant of
Luci. The initial firmware install can be done through this UI,
following normal procedure. I.e., access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to
keep existing settings.
Recovery:
If you brick the device, the C108 supports recovery using TFTP. Keep the
reset button pressed for ~5sec when booting to trigger TFTP. Set the
address of the network interface on your machine to 10.10.10.3/24, and
rename your image file to Kernal.bin.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
In case the link changes from down to up, the register is only updated
on read. If the link failed/was down, this bit will be 0 until after
reading this bit again.
Fixes a reported link down by swconfig alebit the link is up (query for
the link again will show the correct link status)
Signed-off-by: Mathias Kresin <dev@kresin.me>
In conditions where none of the switch ports is connected during boot,
the priv->port[i].link != priv->port[i].phydev->link condition is false
since both link values are equal (false). The carrier of the switch
netdev is never set to off and the link state reported by ip is UNKNOWN.
Turn the carrier off if none of the switch ports has a link, regardless
whether something has been changed. Add a check for a carrier to
prevent unnecessary calls to netif_carrier_off() if the carrier is
already off.
Based on a patch send by Martin Schiller.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Don't return arcount=1 if EDNS0 RR won't fit in the packet.
Omitting the EDNS0 RR but setting arcount gives a malformed packet.
Also, don't accept UDP packet size less than 512 in received EDNS0.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Remove LEDE partial fix for CVE-2017-13704.
Backport official fix from upstream.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> (PKG_RELEASE increase)
Commit 77645ffcd9 ("ramips: add support for the GnuBee Personal Cloud
One") dropped the execution permission from 01_leds with the result
that the file isn't started during first boot and no default LED
configuration is added.
Revert the introduced file permission change.
Fixes: FS#979
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[cherry picked the fix from a board support patch]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Extendprefix is typically used to extend an IPv6 RA prefix from a mobile
wan link to the LAN; such scenario requires correct RA prefix settings
like the on link flag not being set.
However some mobile manufacter set the RA prefix on link flag which breaks
basic IPv6 routing.
Work around this issue by filtering out the route being equal to the
extended prefix.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The WAN port on the Netgear WNDR4300 router has two LEDs,
amber and green. Use the switch LED trigger to behave as the
rest of the LAN HW controlled LEDs
- Green: 1 Gbps
- Amber: 100/10 Mbps
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
1. Add support to LAN/WAN LEDs attached to ar8327.
2. Fix the problem that LAN/WAN LEDs does not blink in hardware (auto)
mode when connected to 10M/100M ethernet.
Signed-off-by: Kuang Rufan <master@a1983.com.cn>
51733a6 ra: align RA update interval with RFC4861 (FS#964)
Add ra_holdoff config option which allows to configure the RA minimum
update interval which is by default 3 seconds as stated in RFC4861.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Refresh patches.
Compile-tested on ramips/mt7621 and x86/64.
Runtime-tested on ramips/mt7621 and x86/64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
b1bc8d5 kmodloader: log error message in case of out of memory
f346111 kmodloader: lift restriction on module alias info
f1ef2c3 kmodloader: fix possible segfaults
9cb63df kmodloader: fix endianess check
2cff779 kmodloader: Check module endian before loading
d54f38a kmodloader/get_module_info: initialized aliases to make it more clean
a0b6fef kmodloader: insmod: fix a memoryleak in error case
278c4c4 kmodloader/get_module_name: null-terminate the string
16f7e16 syslog: remove unnecessary sizeof struct between messages
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This generic structure defines tx_bytes and rx_bytes as unsigned long (u32),
while several devices would typically report unsigned long long (u64).
The code can work as is, but there's a chance that with a sufficiently fast
interface the overflow might happen too fast to be correctly noticed by the
consumers of this data.
This patch makes both field unsigned long long and updates the only known
consumer of this data: swconfig_leds.c
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch provides a generic switch_dev_ops 'get_port_stats()' callback by
taping into the relevant port MIB counters.
This callback is used by swconfig_leds led trigger to blink LEDs with port
network traffic.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch provides a generic switch_dev_ops 'get_port_stats()' callback by
taping into the relevant port MIB counters.
This callback is used by swconfig_leds led trigger to blink LEDs with port
network traffic.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch provides a generic switch_dev_ops 'get_port_stats()' callback by
taping into the relevant port MIB counters.
This callback is used by swconfig_leds led trigger to blink LEDs with port
network traffic.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch provides a generic switch_dev_ops 'get_port_stats()' callback by
taping into the relevant port MIB counters.
The implementation uses a generic callback that select the correct MIB counter
index based on chip version.
This callback is used by swconfig_leds led trigger to blink LEDs with port
network traffic.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch provides a generic switch_dev_ops 'get_port_stats()' callback by
taping into the relevant port MIB counters.
This callback is used by swconfig_leds led trigger to blink LEDs with port
network traffic.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Properly quote the arguments so that you can register a service with TXT
entries that contains spaces.
Example:
procd_add_mdns myservice tcp 9999 "key=descriptive text field 1" \
"another=something equally verbose"
Output before:
$ avahi-browse -r -v _myservice._tcp
_myservice._tcp local
hostname = [blah.local]
address = [192.168.255.74]
port = [9999]
txt = ["verbose" "equally" "another=something" "1" "field" "text" "key=descriptive"]
Output now:
$ avahi-browse -r -v _myservice._tcp
_myservice._tcp local
hostname = [blah.local]
address = [192.168.255.74]
port = [9999]
txt = ["another=something equally verbose" "key=descriptive text field 1"]
Signed-off-by: Karl Palsson <karlp@etactica.com>
This patch fixes the switch port numbering on Mikrotik RB750r2 (hEX lite) and RB750UPr2 (hEX PoE lite).
Tested on a RB750UPr2. Maybe this patch is applicable to other devices (e.g. RB951Ui-2nD, RB952Ui-5ac2nD) but I have no way to test them.
Signed-off-by: João Chaínho <joaochainho@gmail.com>
ssh and scp commands interfere with OpenSSH when installed in /usr/bin .
One use case is when installing dropbear to get root access when only OpenSSH is available (OpenSSH disallows root password logins). Once dropbear installs, it replaces OpenSSH's executables, even when removed with opkg. OpenSSH must be reinstalled to get them back.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Fixes critical issues for memset() & fflush()
Changes:
5f7efb8 move IPPORT_RESERVED from netdb.h to netinet/in.h
5f3b652 add powerpc64 and s390x to list of supported archs in INSTALL
file
9d4c902 fix undefined behavior in memset due to missing sequence points
c7f56b4 __init_libc: add fallbacks for __progname setup
cc08669 add SIOCGSTAMPNS socket ioctl macro to ioctl.h
02b50c9 fix mips ioctl macros to match linux asm/sockios.h
670d6d0 fix unsynchronized access to FILE structure in fflush(0)
Tested on cns3xxx & imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Refresh patches, delete patches backported from upstream.
This fixes ntpd sync issues (ntpd would not sync if the first provided
peer address was unreachable).
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
IPQ806x AP148 and DB149 boards didn't have the UCI ubootenv
section initialized, so the usage of fw_printenv required manual
configuration. With this change, the "fw_printenv" and "fw_setenv"
command will automatically work on NOR and NAND based platforms.
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
busybox currently installs passwd into /usr/bin which prevents its
'full' shadow-utils variant from being installed.
Move the passwd applet to /bin to avoid that collision.
shadow also provides /usr/bin/login which doesn't collide with busybox
as the busybox login applet is installed at /bin/login.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
busybox currently installs traceroute and traceroute6 into /usr/bin
which prevents their 'full' iputils variants from being installed.
Move those applets to /bin so they can coexist with their iputils
siblings using the same PATH convention already applied for coreutils
and other drop-in 'full' versions.
Refresh existing patch while at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
printer support is removed using 200-remove_printer_support.patch. the syslog parameter requires samba to be compiled with --with-syslog. Currently samba does not log to syslog and probably has not for a long time.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
If CONFIG_DOWNLOAD_FOLDER is set to for example "~/dl", the download
script fails to create the .hash and .dl files with the following
errors:
Cannot create file ~/dl/dropbear-2017.75.tar.bz2.dl: No such file or directory
sh: 1: cannot create ~/dl/dropbear-2017.75.tar.bz2.hash: Directory nonexistent
If the tarball already exists in the ~/dl dir, it's properly found and
used, so this issue only affects the download.pl script.
This patch calls glob() on the target dir parameter, which will expand `~`.
Signed-off-by: Zoltan Gyarmati <mr.zoltan.gyarmati@gmail.com>
Changes:
1698fe6 fix build failure for sh4a due to missing colon in asm statement
80bf595 trap UB from attempts to join a detached thread
e31c8c2 ppc64: fix setjmp/longjmp handling of TOC pointer
52cf5c1 qsort: add a short comment about the algorithm
dc2f368 disable global visibility override hack (vis.h) by default
947d330 add _NL_LOCALE_NAME extension to nl_langinfo
a08910f fix missing volatile qualifier on lock in __get_locale
2e6e084 remove ineffective compiler assist from printf
bc42dcb fix undefined behavior in ptrace
d906fa3 unify the use of FUTEX_PRIVATE
60ab365 fix undefined behavior in free
f688884 reapply va_arg hacks removal to wprintf
bd00cc8 remove useless declarations in string.h
f3055e0 allow specifying argv[0] when invoking a program via ldso
command
43c423a fix regression in dlopen promotion from RTLD_LOCAL to
RTLD_GLOBAL
66b53cf ldso: avoid spurious & possible erroneous work for libs with no
deps
94f7441 powerpc64: add single-instruction math functions
9d12a6a fix clang CFLAGS checks and silence unused argument warnings
ce385fc s390x: add single-instruction math functions
e6def54 fix arm run-time abi string functions
91d34c4 fix regression in getspnam[_r] error code for insufficient
buffer size
5948bc1 fix omission of microblaze user.h definitions
b7bfb5c fix iconv conversions for iso88592-iso885916
64f8558 handle errors from localtime_r in ctime_r
2d7d05f set errno when getpw*_r, getgr*_r, and getspnam_r fail
5c10c33 handle localtime errors in ctime
1c86c7f handle mremap failure in realloc of mmap-serviced allocations
1080008 getdate: correctly specify error number
af05173 catopen: set errno to EOPNOTSUPP
84eff79 fix glob failure to match plain "/" to root directory
bc313e8 use hard-coded sh4a atomic opcodes to avoid linker errors on sh
179766a towupper/towlower: fast path for ascii chars
1c49700 remove long-obsolete clang workarounds from mips* syscall_arch.h
files
4073f03 fix fstatat syscall on mips64
81f4a12 fix fchown fallback on arches without chown(2)
97bd6b0 fix iconv conversions to legacy 8bit encodings
f9f686b have posix_spawnattr_setflags check for supported flags
77e895d add no-op POSIX_SPAWN_USEVFORK to spawn.h
5555041 s390x: provide sigcontext struct definition
bb439bb implement new posix_spawn flag POSIX_SPAWN_SETSID
58e2396 remove va_arg hacks in printf core with undefined behavior
e1232f5 make ttyname[_r] return ENODEV rather than ENOENT
1a7fa5e fix regression in support for resolv.conf attempts option
8c44a06 fix scalbn when result is in the subnormal range
2577b1b allow full-range file offsets to mmap on archs with 64-bit
syscall args
b3751c3 fix dl_iterate_phdr in static PIE binaries
1ca5975 fix read past end of buffer in getaddrinfo backend
54807d4 aarch64: add single instruction math functions
b6e1fe0 fix strptime output for %C without %y
834ef7a fix processing of strptime %p format
85dfab7 fix off-by-one in strptime %j
9571c53 regex: fix newline matching with negated brackets
e6917ec increase limit on locale name length from 15 to 23 bytes
e4fc9ad search locale name variants for gettext translations
16319a5 make setlocale return a single name for LC_ALL if all categories
match
0c53178 fix dlopen/dlsym regression opening libs already loaded at
startup
dbff2bb fix POSIX-format TZ dst transition times for southern hemisphere
74bca42 s390x: fix fpreg_t and remove unused per_struct
a393d5c precalculate gnu hash rather than doing it lazily in find_sym
inner loop
8cba1dc fix threshold constants in j0f, y0f, j1f, y1f
cb52539 remove unused refcnt field for shared libraries
c49d3c8 avoid loading of multiple libc versions via explicit pathname
3ec8b3a fix one-byte overflow in legacy getpass function
733d1ea fix wide scanf's use of a compound literal past its lifetime
6a209f1 fix possible fd leak, unrestored cancellation state on dns
socket fail
500f5be in static dl_iterate_phdr, fix use of possibly-uninitialized aux
data
6582baa fix free of uninitialized buffer pointer on error in regexec
6476b81 emulate lazy relocation as deferrable relocation
4823b13 reorder addend handling before symbol lookup in relocation code
4ff234f rework ldso handling of global symbol table for consistency
c9783e4 treat STB_WEAK and STB_GNU_UNIQUE like STB_GLOBAL in find_sym
fc85fb3 fix ld-behavior-dependent crash in ppc64 ldso startup
827c4e6 fix lsearch and lfind to pass key as first arg to the compar
callback
0a4a16d allow page size to vary on arm
b261a24 fix build regression in arm atomics asm with new binutils
9201c3a s390x: implement dlsym
d6601f0 avoid unbounded strlen in gettext functions
dbbb373 fix use of uninitialized pointer in gettext core
01e6bbe fix bindtextdomain logic error deactivating other domains
6894f84 fix spurious EINTR errors from multithreaded set*id, etc.
1f53e7d fix crashes in x32 __tls_get_addr
27b3fd6 fix crash from corrupted tls module list after failed dlopen
809ff8c treat base 1 as an error in strtol-family functions
786fda8 fix getopt[_long] clobbering of optopt on success
150747b reduce impact of REG_* namespace pollution in x86[_64] signal.h
Tested on cns3xxx & imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
It's redundant and also buggy. IPv6 link local addresses and ::1 are not resolved for example. Doesn't matter since lo and br-lan for example, resolve to them.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
guest ok is set per share and as such, don't override it. also, fix an error introduced in the last commit.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The ramips subtargets of mt7628 and mt7688 dts files all #include "mt7628an.dtsi"
They are essentially a single subtarget.
This patch merges the ramips subtargets mt7628 and mt7688 into a single subtarget mt76x8.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
