Disable video and input drivers - they are needed only for one
board and can be enabled via modules if/when UI will be available.
Use LED drivers from packages.
Cleanup other things unnecessarily overriding defaults.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
This adds the patches to get fairly complete Gemini support
using kernel v4.14. It is mainly a backport of patches from
kernel v4.16 with omissions of things like graphics that require
substantial changes and will be better handled once we move
to the v4.16 kernel proper.
On top of this are some WIP patches for USB support.
Tested on Raidsonic NAS4220B and D-link DNS-313.
ChangeLog v4->v5:
- Fix ethernet single gmac usecase
- Fix USB reset (patch from Hans)
- Fix Raidsonic ethernet skew delay
- Fix kernel config (bridge, squashfs, jffs2, usb)
- Disable second usb port on Raidsonic board until fotg210_hcd is fixed
ChangeLog v3->v4:
- Make sure to use tabs rather than spaces in base-files.
- Use the dns313 image tool from the firmware-utils.
- Break out the addition of the v4.14 patches and the removal
of the v4.4 patches to separate (big) patches.
ChangeLog v2->v3:
- Update the kernel config as indicated by Hauke Martens:
- Regenerate again after rebasing using kernel_oldconfig
dropping a few optimization settings that are now generic
- Drop CFG80211 stuff (module)
- Drop CIFS stuff (module)
- Drop MAC80211 (module)
- Drop wireless drivers (module)
- Enabled OverlayFS
- Added proper DNS-313 boot image generation with the special
file header tool.
- Disable CMA in the kernel
- Enable LZMA compression of the kernel
- Consequently name the nas4220b images nas4220b
- Update preinit MAC detection script to handle also DNS-313
- Add board.d/03_hdparm to set the disk to spin down after
1 minute by default, if we have the hdparm tool installed
ChangeLog v1->v2:
- Processed config through kernel_oldconfig
- Processed patches through make target/linux/{clean,refresh} V=99
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Add target device as at91-sama5d2_ptc_ek in SAMA5D2 subtarget and
build images for SAMA5D2 PTC Ek board.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
reorganizing at91 subtargets based on sama5 soc features and this fix
below problems.
1. able to set neon flags to sama5d2 & sama5d4 subtargets.
2. fix the make clean which removes all the subtargets in bin folder.
3. able to configure kernel specific to subtarget.
4. able to set vfpu4 flags to samad3 subtargets.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
creating sdcard image with ext4 rootfs only and ignoring creating
other filesystem in sdcard image.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Add support for SAMA5D27 SOM1 with target device as at91-sama5d27_som1_ek
in SAMA5 subtarget and build images for SAMA5D27 SOM1 Ek board.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
copying at91bootstrap and uboot binaries to sdcard image is done
based on device name instead of dts name and this avoids creating
multiple u-boot and at91bootstrap binaries.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
In typical OpenWrt setups, there are no other users that have a shell spawned for them by default.
This can be overriden by the kernel.dmesg_output syssctl.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
sama5d2 & samad4 have neon feature and sama5d3 does not have neon
feature due to which sama5d3 boot fails with error message Kernel
panic - not syncing: Attempted to kill init! exitcode=0x00000004.
removing neon & VFPv4 support to fix this
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
when external kernel is selected from menuconfig, device wb50n is not
avaliable and build fails. As a fix adding checks for external kernel.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Kernel support already present.
Patch adds userspace for the 'iLS' suffix model of the RB2011 family.
Enables correct initial switch settings, sysupgrade, etc.
https://mikrotik.com/product/RB2011iLS-IN
Signed-off-by: Simon Paterson <simon.paterson.nz@gmail.com>
The harden branch predictor was backported for arm64 with 4.9.92-96.
Fixes: 9aa196e0f2 ("kernel: bump 4.9 to bump 4.9.96")
Signed-off-by: Mathias Kresin <dev@kresin.me>
This is mainly a bug fix for multi-core MIPS systems where L1 caches besides the primary do not get flushed.
The most obvious problem is data corruption on SATA and USB devices where read requests are typically larger than the cacheline size.
This may also fix ar71xx systems that suffer from similar data corruption but I have not tested if it does.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Some Ubiquiti U-boot versions, in particular the "U-Boot 1.1.4.2-s956
(Jun 10 2015 - 10:54:50)" found with AirOS 5.6, do not correctly flush the
caches for the whole kernel address range after decompressing the kernel
image, leading to hard to debug boot failures, depending on kernel version
and configuration.
As a workaround, prepend the relocate-kernels loader, which will invalidate
the caches after moving the kernel to the correct load address.
Reported-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
There is no pinmux group "jtag" for mt7628 and the pinmux driver fails
to load due to the use of the not existing group.
Fixes: FS#1515
Signed-off-by: Mathias Kresin <dev@kresin.me>
The old DTB method (OWRTDTB) is not recognized by the boot process
anymore with 4.9/4.14.
This patch reuses KERNEL_DTB to get a valid DTB applied to the kernel
image.
Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
The current option driver binds to the usb interface 2,3,4,5.
But the interface 4 and 5 doesn't answer to the AT commands.
On the new openwrt configuration the wwan script select the 5th
interface as control interface, failing to establish the
3G connection.
Backport the fix for the problem.
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ 802.3at POE+
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 18-24V passive POE (mode B)
* powered only via POE
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
The initramfs image can be started using
setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
set fdt_high 0x85000000
bootm 0x84000000
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
The pinctrl initialization fails with the MSM pinctrl code and gpio-hogs
because either the gpio ranges are not yet initialized (missing gpio-range
in DT) or that the msm driver unconditionally tries to re-initializes the
ranges (gpio-range in DT).
To allow gpio-hogs and similar early-boot gpio code, the gpio-ranges must
be in the device tree and the pinctrl-msm code must check whether the range
was already initialized by the DT.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
[drop changes to unrelated dtsi files, refresh patches]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The BDFs for all boards were upstreamed to the ath10k-firmware
repository and are now part of ath10k-firmware 2018-04-19.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
These devices have only one ethernet port. It doesn't make sense to
expose the unused GMACs as separate network devices.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
The tz and smem reserved-memory information handled in the upstream Linux
sources by the SoC specific dtsi and not by the the boards dts. Using the
same approach in OpenWrt avoids unneccessary duplication.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
The reserved-memory regions are mostly undocumented by QCA and are named
very unspecific in the QSDK device trees. It was tried to clean them up by
commit 71ed9f10a3 ("ipq40xx: Use detailed reserved memory for A42") and
similar changes.
The features which require these regions were mostly unknown but
Senthilkumar N L <snlakshm@qti.qualcomm.com> and Sricharan Ramabadhran
<srichara@qti.qualcomm.com> provided some more insight in some of them:
* crash dump feature
- a couple of regions used when 'qca,scm_restart_reason' dt node has the
value 'dload_status' not set to 1
+ apps_bl <0x87000000 0x400000>
+ sbl <0x87400000 0x100000>
+ cnss_debug <0x87400000 0x100000>
+ cpu_context_dump <0x87b00000 0x080000>
- required driver not available in Linux
- safe to remove
* QSEE app execution
- region tz_apps <0x87b80000 0x280000>
- required driver not available in Linux
- safe to remove
* communication with TZ/QSEE
- region smem <0x87b80000 0x280000>
- driver changes not yet upstreamed
- must not be removed because any access can crash kernel/program
* trustzone (QSEE) private memory
- region tz <0x87e80000 0x180000>
- must not be removed because any access can crash kernel/program
Removing the unnecessary regions saves some kilobyte of reserved-memory and
cleans up the device tree:
* 2560 KiB
- 8devices Jalapeno
- AVM FRITZ!Box 4040
- Compex WPJ428
- Meraki MR33 Access Point
- OpenMesh A42
* 14336 KiB
- GL.iNet GL-B1300
- Qualcomm Technologies, Inc. IPQ40xx/AP-DK01.1-C1
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Merge the two existing functions and use a parameter for the type
header field.
It updates the syntax of the former mpc85xx fake ramdisk header
command to be compatible with mkimage from u-boot 2018.03 and fixes the
build error spotted by the build bot.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This reverts commit 5555545494.
The target supports both NEON and VFPv4, but for this to work properly,
a few more changes are needed:
- enable NEON support in the kernel config
- add the fpu feature flag to the makefile
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The stats update needs to protect against being interrupted by a tasklet
The u64 stats seqlock needs to be initialized
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The pins are used as (LED) GPIOs and can't be used at the same time as
hardware controlled ephy (LED) pins.
Fixes: FS#1500
Signed-off-by: Mathias Kresin <dev@kresin.me>
