Add a helper variable which contains the boardname separated from the
vendor name. It allows to switch to a device tree compatible string
based boardname, by keeping the $board:colour:function syntax in
scripts handling/adding config for LEDs.
Boards not using the device tree compatible string as based boardname
are unaffected by the change, since none of them uses a comma in the
boardname.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use <manufacturer>_<modelname> as image name for board using the
devicetree compat string as boardname.
Replace the underline of the device define, to keep the SUPPORTED_DEVICES
in sync with a devicetree compat string based boardname.
Override the default SUPPORTED_DEVICES for board which are having an
userspace boardname with an underline.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The LinkIt Smart 7688/LinkIt Smart 7688 Duo are identical beside the
extra ATmega32U4 - accessible via UART - on the the Duo.
Since all relevant hardware is identical, drop the Duo special handling
in userspace.
Signed-off-by: Mathias Kresin <dev@kresin.me>
If we need to set the initial output value to GPIOF_OUT_INIT_HIGH (1) to
enable something, the pin is ACTIVE_HIGH. The same applies to
GPIOF_OUT_INIT_LOW (0) and ACTIVE_LOW.
Signed-off-by: Mathias Kresin <dev@kresin.me>
In the stock firmware both eth0 and eth1 are set to br-lan,
add this behavior to our images.
Fixes: FS#1084
Signed-off-by: Marty E. Plummer <hanetzer@protonmail.com>
The status led part was missed when changing the board name to *-nor.
Fixes: e12c72bb52 ("brcm63xx: Add Sercomm AD1018 support")
Reported-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Use <manufacturer>_<modelname> as image name.
Use the BOARD_NAME variable to ensure that the former used boardname is
still used as the subdirectory name for the sysupgrade-tar image, to
not break sysupgrade from earlier versions.
While at it, normalise the image filenames by using only lower case
characters and bin as file extension for sysupgrade images.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the first compatible string as board name in userspace. Add the new
board name as well as the former used board name to the image metadata
to keep compatibilty with already deployed installations.
Don't add the former used boardname for boards which exists only in
master or evaluation boards.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This adds basic support for kernel 4.14, this was tested in qemu only.
The subtarget configuration was refresh with kernel 4.14 and the
options needed to make it compile on kernel 4.9 were added manually.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In kernel 4.14 kmod-bluetooth depends on kmod-crypto-ecdh, add
kmod-crypto-ecdh to LEDE.
Both packages also depend on the kmod-crypto-kpp package. To build this
we have to fix the dependency of CRYPTO_ECDH which has a typo.
This patch is already accepted upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds initial support for kernel 4.14 based on the patches for
kernel 4.9.
In the configuration I deactivated some of the new possible security
features like:
CONFIG_REFCOUNT_FULL
CONFIG_SLAB_FREELIST_HARDENED
CONFIG_SOFTLOCKUP_DETECTOR
CONFIG_WARN_ALL_UNSEEDED_RANDOM
And these overlay FS options are also deactivated:
CONFIG_OVERLAY_FS_INDEX
CONFIG_OVERLAY_FS_REDIRECT_DIR
I activated this:
CONFIG_FORTIFY_SOURCE
CONFIG_POSIX_TIMERS
CONFIG_SLAB_MERGE_DEFAULT
CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED
I am not sure if I did the porting correct for the following patches:
target/linux/generic/backport-4.14/020-backport_netfilter_rtcache.patch
target/linux/generic/hack-4.14/220-gc_sections.patch
target/linux/generic/hack-4.14/321-powerpc_crtsavres_prereq.patch
target/linux/generic/pending-4.14/305-mips_module_reloc.patch
target/linux/generic/pending-4.14/611-netfilter_match_bypass_default_table.patch
target/linux/generic/pending-4.14/680-NET-skip-GRO-for-foreign-MAC-addresses.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Just refresh the kernel configuration, some options are removed because
they are now in the generic kernel configuration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These are taken from the x86 target and should make support kernel 4.9
and 4.14 in the x86 target easier.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cover temperature sensors for all mainstream 64-bit processors, including
AMD 10h and 15h families, Intel iCore, Xeon, Atom, and Via Nano. Also
add CPUID support for user-space applications to detect CPU type.
Include the on-chip sensors for 64-bit CPU's in the generic profile
in case someone builds a 32-bit kernel to run on a Xeon SoC, etc.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Backport the mdio-bus reset gpio support from 4.12 and use it instead
of toggling the reset ourself.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Add support for the Sercomm AD1018 router
This a BCM6328 based board, 128 MB RAM, 128 MiB NAND flash,
with an onboard BCM43217 wifi, 4 ethernet ports and 1 USB
host port (not soldered). The board also has an FXS chip (Si32177)
connected via SPI (SS2#), without support in LEDE.
Since NAND flash chips aren't still supported in brcm63xx, the
support is for now added to work only with SPI flash chips. Therefore
hardware modding, soldering a new SPI flash chip, is required
to make the board work with LEDE (tested and working OK).
The flash at dts is intentionally left without partitioning to let
the user choose a NOR chip of any size (8, 16 or 32 MB).
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
[jonas.gorski: renamed ad1018 to ad1018-nor to signify the modification]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Since Linux 4.6, mtd->priv no longer points to the NAND specific
structure. Under 4.9 it contains NULL, thus using it to access
chip->options causes an invalid pointer dereference (FS#1200).
Update the code to use the mtd_to_nand() helper under 4.9 to obtain
the address of the chip specific data.
Fixes: 7bbf4117c6 ("ar71xx: Add kernel 4.9 support")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Since Linux 4.6, mtd->priv no longer points to the NAND specific
structure. Under 4.9 it contains NULL, thus using it to access
the fields of the nand_chip structure causes an invalid pointer
dereference.
Update the code to use the mtd_to_nand() helper under 4.9 to obtain
the address of the chip specific data.
Compile tested only.
Fixes: 7bbf4117c6 ("ar71xx: Add kernel 4.9 support")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Tested-by: Christian Lamparter <chunkeey@gmail.com>
When mtdsplit_minor.c is compiled under Linux 4.4, the compiler
drops the following warning:
CC drivers/mtd/mtdsplit/mtdsplit_minor.o
drivers/mtd/mtdsplit/mtdsplit_minor.c:106:14: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types]
.parse_fn = mtdsplit_parse_minor,
^
drivers/mtd/mtdsplit/mtdsplit_minor.c:106:14: note: (near initialization for 'mtdsplit_minor_parser.parse_fn')
The second parameter of the parser function must not have a 'const'
qualifier in 4.4. The 001-mtdsplit_backport.patch removes the qualifier
from other partition parsers. Update it to handle mtdsplit_minor.c as
well.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
This reverts commit 256990cbc0.
this commit caused a compile error
"TL_WR1043_V5_GPIO_LED_WANORANGE" is undefined.
Signed-off-by: John Crispin <john@phrozen.org>
Add missing definitions for the orange WAN LED on the TL-WR1043N(D) v4 and
v5. Minor format correction on a constant for consistency.
Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
This patch fixes the switch port numbering on Mikrotik RB951Ui-2nD (hAP).
Also fixes the switch port numbering shown on LuCI for Mikrotik RB493G.
Signed-off-by: João Chaínho <joaochainho@gmail.com>
Advantages:
- preserves existing partition layout. On the hard-drive.
Only the boot and rootfs partition will be overwritten.
Disadvantages:
- The upgrade process takes much longer to run.
from 2-3 seconds to 15-25 seconds.
Please note that sysupgrade will refuse to upgrade, if the existing
installation has an incompatible partition layout. Future changes
to the bootfs and/or rootfs partition size will likely cause breakage
to the sysupgrade procedure. In these cases, the ext4-rootfs.img.gz
has to be written manually onto the disk. Please don't forget to backup
your configuration in this cases.
Note2: This patch requires
"base-files: upgrade: make get_partitions() endian agnostic"
Note3: If your current installation does not host the two
changes, sysupgrading will wipe the existing partition
layout. Don't forget to backup your data!
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Please note that users with a Netgear WNDR4700
will need to update the device-tree partition
manually.
For instructions, please refere to commit 49856a4bb5
("apm821xx: make it possible to update the dtb partition on the WNDR4700")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Lantiq and IPQ806X (which includes IPQ40XX) both define the
same custom function {ipq806x|lantiq}_get_dt_led.
This patch moves the function into the base-file package at
lib/functions/leds.sh to make it more accessible for other
targets as well.
Cc: Mathias Kresin <dev@kresin.me>
Cc: John Crispin <john@phrozen.org>
Cc: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The bcm6368 pinctrl driver passed the wrong variable to
devm_regmap_field_alloc, causing it to blow up when later trying to
access the field.
Fixes#1211.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
For an unknown reason gcc tries to link in crti.o when building with a
glibc toolchain (this does not happen with other targets). Prevent this
by telling gcc explicitly to not do that.
Fixes the following build error:
/home/jonas/git/lede/staging_dir/toolchain-mips_24kc_gcc-5.5.0_glibc/lib/gcc/mips-openwrt-linux-gnu/5.5.0/../../../../mips-openwrt-linux-gnu/lib/crti.o: In function `_init':
(.init+0x18): relocation truncated to fit: R_MIPS_GOT16 against `__gmon_start__'
/home/jonas/git/lede/staging_dir/toolchain-mips_24kc_gcc-5.5.0_glibc/lib/gcc/mips-openwrt-linux-gnu/5.5.0/../../../../mips-openwrt-linux-gnu/lib/crti.o: In function `_init':
(.init+0x28): relocation truncated to fit: R_MIPS_CALL16 against `__gmon_start__'
collect2: error: ld returned 1 exit status
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
This will avoid some conflicts when doing a git rebase or merge,
specially when adding support to a new device.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
[drop brcm47xx changes which rename the images]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Recent RouterBOOT version (at least version 3.41 on RB911G-5HPacD)
use "Board=" kernel parameter instead of "board=" to pass the board
name to the kernel. Due to this change the board detection code is
not working on the devices shipped with the new RouterBOOT version.
Because the kernel is unable to identify these boards they become
unusable despite that they are supported by the current code.
Update the prom_init code to convert the 'Board' kernel parameter to
'board'. After this change, the board detection works also with the
new RouterBOOT versions.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The target name does not need to included a revision
if all revisions are supported.
This target supports all revisions (v1, v2, v2.1).
Signed-off-by: Moritz Warning <moritzwarning@web.de>
[Keep the version numbers in the device title, it doesn't harm]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Remove the WW suffix, everything without a region suffix is world wide
anyway.
While at it, normalise the image filenames by using only lower case
characters.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Users are confused which image type they should use and there are more
drawbacks than adavantages in using a r/w ubifs rootfs in constrast to
a read-only squashfs rootfs like:
- less available free flash space due to better compression of squashfs
images
- no support for factory reset due to r/w filesystem
- possibility to break failsafe due to r/w filesystem
Therefore, drop support for r/w ubifs rootfs images.
Signed-off-by: Mathias Kresin <dev@kresin.me>
