This is not needed after all:
Omitting option ipv6 or setting it to 'auto' will
fire up a dhcpv6 subprotocol (this was added).
Setting ipv6 to 1 will only cause the IPv6 link to
be brought up and an accompanying dhcpv6 or static
interface with ifname @wan can be used to configure addresses.
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 42859
Use network_get_ipaddrs_all to get all ip-addresses of an interface. If the
function fails, the interface does not exists or has not any suiteable ip
addresses assigned.
Use the returned ip-address(es) to construct the dropbear listen address.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 42857
this proto handler will detect which of 3g, qmi, mbim, ncm or directip you need
for a stick and setup uci automagically
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 42837
Some ISP seem to only do stateful DHCPv6 and not sending RAs.
This is technically broken because plain DHCPv6 doesn't carry routes.
We work around here by faking a default route to the DHCPv6 server
if we do not receive a useful RA from the ISP.
This workaround can be turned off with: option fakeroutes 0
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 42803
The AR9580 with the new ID can be found in the EnGenius ESR900 and the
QCA9880 without any subsystem IDs can be found in the EnGenius ESR1750.
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
SVN-Revision: 42793
In r41872 Dynamic VLAN support was reintroduced, but the vlan_naming
parameter is not read while setting up the config, so it always
defaults to 1.
Signed-off-by: Reiner Herrmann <reiner@reiner-h.de>
SVN-Revision: 42787
Send a netlink call to leave the mesh when meshd exits
Make hunting-and-pecking loop (more) resistant to side channel attack
Signed-off-by: Michel Stam <m.stam@fugro.nl>
SVN-Revision: 42750
Tos support is added as a string parameter which can have the following values :
-inherit (outer header inherits the tos value of the inner header)
-hex value
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 42749
Tos support is added as a string parameter which can have the following values :
-inherit (outer header inherits the tos value of the inner header)
-hex value
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 42748
Tos support is added as a string parameter which can have the following values :
-inherit (outer header inherits the tos value of the inner header)
-hex value
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 42747
The package supports IP in IP by registering the ipip protocol handler
Following options are configurable
-peeraddr (IPv4 remote address)
-ipaddr (IPv4 local address)
-ttl (time to live of encapsulating packet)
-tos (type of service of encapsulating packet either inherit (outer header inherits the value of the inner header) or hex value)
-df (don't fragment flag of encapsulating packet)
-mtu (IPIP tunnel mtu)
-tunlink (bind tunnel to this interface)
-zone (firewall zone to which the IPIP tunnel will be added)
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 42746
When 'wifi down' is called by /etc/init.d/network, it is run from
stop_service( ). This function is in turn invoked from stop( ).
stop( ) messes up the order by first procd_kill-ing the network
settings, then calling wifi to down the wifi networking
interfaces. By redefining stop( ) instead, the proper order is
restored.
Signed-off-by: Michel Stam <m.stam@fugro.nl>
SVN-Revision: 42745
Instead of connecting once and saving the packet data handle, let the
firmware handle connecting/reconnecting automatically. This is more
reliable and reduces reliance on potentially stale data.
Use the global packet data handle to attempt to disable autoconnect
before restarting the connection. This ensures that the firmware will
take the new APN/auth settings.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 42721
Tos support is added as a generic grev4/grev6 parameter which can have the following values :
-inherit (outer header inherits the tos value of the inner header)
-hex value
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 42700
Main changes:
- URL parser: IPv6 zone identifiers are now supported
- cyassl: Use error-ssl.h when available (drop local patch)
- polarssl: support CURLOPT_CAPATH / --capath
- mkhelp: generate code for --disable-manual as well (drop local patch)
Full release notes: http://curl.haxx.se/changes.html
MIPS 34kc binary size:
- 7.36.0 before: 82,539 bytes
- 7.38.0 after: 83,321 bytes
Signed-off-by: Catalin Patulea <cat@vv.carleton.ca>
SVN-Revision: 42517
With this patch WPS discovery can be started or canceled over ubus if
WPS is enabled in wireless configuration. This is equivalent of
'hostapd_cli wps_pbc' and 'hostapd_cli wps_cancel' commands.
Signed-off-by: Petar Koretic <petar.koretic@sartura.hr>
SVN-Revision: 42459
* ipv6
* 4 bugs in the dns parser
* service announcement
* tx goodbye support
* proper handling of rx goodbye
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 42325
Use an if/else statement to cover the two different syntaxes. Add
comments explaining what the end results should look like.
This patch should not change the script's output.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
SVN-Revision: 42320
An entry like this in /etc/config/dhcp:
config 'host'
option 'name' 'pc2'
option 'ip' '192.168.100.56'
option 'dns' '1'
results in a /tmp/hosts/dhcp entry that looks like this:
192.168.100.56 .lan
Obviously it should say "pc2.lan".
This happens because $name is set to "" in order to support the MAC-less
syntax: "--dhcp-host=lap,192.168.0.199". Fix this by reordering the
operations. Also, refuse to add a DNS entry if the hostname or IP is
missing.
Fixes#17683
Reported-by: Kostas Papadopoulos <kpapad75@travelguide.gr>
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
SVN-Revision: 42319
LuCI creates "domain" UCI config sections, which the dnsmasq init file
then, currently, translates into "address" config lines. This is not
the correct usage of "address" (see r36943), and also causes rDNS
records to not be created. This patches dnsmasq.init to utilize the
additional hosts file introduced in r40799 for such domain names,
resolving both issues.
Signed-off-by: Tyler Fenby <tylerf@securecominc.com>
SVN-Revision: 42318
A quite frequent problem after sysupgrading from an older, SSL enabled build
is that ustream-ssl is not installed so uhttpd fails to come up again due to
https listening directives in the preserved configuration.
Skip key/cert and ssl listen options when libustream-ssl.so is not present.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42284
somebody started to set a function returncode in the validation
stuff and everybody copies it, e.g.
myfunction()
{
fire_command
return $?
}
a function automatically returns with the last returncode,
so we can safely remove the command 'return $?'. reference:
http://tldp.org/LDP/abs/html/exit-status.html
"The last command executed in the function or script determines the exit status."
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 42278
Disable MIPS16 to prevent it negatively affecting performance.
Observed was a increase of connection delay from ~6 to ~11 seconds
and a reduction of scp speed from 1.1MB/s to 710kB/s on brcm63xx.
Fixes#15209.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42250
Add a further upstream commit to more closely match the keepalive
to OpenSSH.
Should now really fix#17523.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42249