The boardname isn't used any longer to find the subdirectory in the
sysupgrade tar archive, which makes this override useless.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Qualcomm claims this reduces cache misses. Original commit message below:
From: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Date: Tue, 11 Jun 2013 12:18:46 -0500
Subject: [ag71xx] reduce NAPI weight
In an attempt to increase our cache warmth, we are decreasing NAPI.
This increases the warmth of the reused SKBs.
Signed-off-by: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The motivation for this was misguided. It turns out tuning the NAPI weight could be useful for testing purposes. Therefore reverting.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This commit fixes LAN Port 1 not transferring data in case no
other LAN Port has active link-state on TP-Link Archer C58/C59.
Signed-off-by: David Bauer <mail@david-bauer.net>
This is a variant of the MT7620N-based Asus routers.
Specifications:
- MT7620N (580 MHz)
- 32 MB RAM
- 8 MB Flash
- 5x 10/100Mbps Ethernet (built-in switch)
- 2.4 GHz WLAN
- 2x external, non-detachable antennas
- UART (J2) header on PCB (115200 8n1)
Flash instructions:
1. Configure PC with static IP 192.168.1.75/24
2. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds. All 4 LEDs will
start to blink, which is when the router will accept firmware files via TFTP.
No known limitations on firmware filenames, just send it with a TFTP client
to 192.168.1.1.
3. Router will download file from server, write it to flash and reboot.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This allows people to build SDK from custom repository (git access using
ssh) and keep original URL in SDK's feeds.conf.default.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Jo-Philipp Wich <jo@mein.io>
This commit adds missing the GPIO key used as reset button.
Nexx WT1520 has a GPIO key for factory reset, but it's not defined in
WT1520.dtsi and cannot use it.
Drop the UART (full) from the device tree source file, it was never
used for this board. Adjust the kernel bootargs accordingly.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[add note about dropped UART (full) to the commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
There are multiple problems on the A64 SoC with the older drivers which
are fixed in the upstream kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add pinmuxes defined by some board which are including the dtsi files
to the dtsi files itself. Allows to reduce duplication.
Signed-off-by: Mathias Kresin <dev@kresin.me>
According to the datasheet the REFCLK pin is shared with GPIO#37 and
the PERST pin is shared with GPIO#36.
While at it fix a typo inside the pinmux setup code. The function is called
refclk and not reclk.
Update device tree source files accordingly.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add kmod-sound-core, it is a dependency of kmod-sound-mt7620 and will
not be autoselected.
Remove kmod-i2c-core, it will be autoselected by kmod-i2c-ralink.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Setting the pins of the UARTF group to GPIO+I2S at the time the I2C
driver loads is to late for the wps GPIO button.
The gpio-keys driver fails to load since the pin used by the wps button
is not yet set to GPIO. The wps button with the rfkill keycode is
essential for this wireless only board.
Add the missing sound and I2C kernel modules corresponding to the
device nodes.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The advantage is that we don't have to specify max TRX size anymore and
otrx doesn't allocate a buffer of that size. It saves us allocating
32 MiB for every image we generate.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Backported devicetree from Kernel 4.13 with some additions
to enable Ethernet and WiFi module
The following features are working:
- Ethernet
- WiFi
- eMMC and microSD slot
- USB ports
The following features are not working:
* Bluetooth
NanoPi M1 Plus key features
- SoC: Allwinner H3, Quad-core Cortex-A7@1.2GHz
- RAM: 1GB DDR3
- eMMC: 8GB
- microSD slot
- Ethernet 10/100/1000M
- Wifi: AP6212
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
D-Link DIR-330 is clone of ASUS WL500GP2, by default conf the WAN port is
eth1, it's not working cus eth1 not soldered and wan port function
performs 5th port of the switch.
Signed-off-by: Antony Black <gtrtfm@gmail.com>
Currently local TCP performance on wifi devices can be limited because
the TSQ (TCP Small Queues) code is tuned for wired ethernet latencies.
With this patch drivers can increase the amount of local buffering to
allow TCP to trigger larger aggregation sizes
This commit is modified from the upstream version to allow #ifdef based
backport feature detection
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a variant of the ZBT WG3526 with a few minor modifications.
The wifi chips are swapped, and there is no GPIO controllable status
LED. There is also no SATA port.
Specifications:
- MT7621AT (880 MHz)
- 512 MB RAM
- 16 MB Flash (SPI NOR)
- 5x 1Gbps Ethernet (built-in switch)
- MT7612E 802.11ac 5 GHz WLAN
- MT7603E 802.11n 2.4 GHz WLAN
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The IRQ controller can only set the affinity to a single CPU. Update the
mask in the controller data.
Suggested-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
TP-Link TL-WR802N v1 and v2 are set up with almost same configuration in
the mach-files. Merge the mach-files of these devices.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
TP-Link TL-WR1043N v5 appears to be identical to the TL-WR1043ND v4,
except that the USB port has been removed and there is no longer a
removable antenna option.
The software is more in line with the Archer series in that it uses a
nested bootloader scheme.
Specifications:
- QCA9563 at 775 MHz
- 64 MB RAM
- 16 MB flash
- 3 (non-detachable) Antennas / 450 Mbit
- 1x/4x WAN/LAN Gbps Ethernet (QCA8337)
- reset and Wi-Fi buttons
Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
The TL-WA901ND v5 has the same hardware as v4, although the PCB has
a different layout. Installation from factory is done via TFTP.
(rename -factory image to wa901ndv4_tp_recovery.bin for tftp)
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
This patch adds support for the MikroTik RouterBOARD mAP 2nD
https://mikrotik.com/product/RBmAP2nD
Specifications:
- SoC: Qualcomm QCA9531 (650 MHz)
- RAM: 64 MB
- Storage: 16 MB NOR SPI flash
- Wireless: builtin QCA9531, 2x2:2
- Ethernet: 2x100M (802.3af/at POE in and passive POE out on ETH2)
- USB: microUSB type AB port
This patch adds missing code to fully support mAP. Machfile already
contained configuration for mAP 2nD, but device specific configuration
like LEDs etc., was missing.
Note: The POE LED works but doesn't turn on when POE passthrough is
enabled, despite being configured with GPIO trigger.
Installation
1. Login to the Mikrotik WebUI to backup your licence keys
2. Setup a DHCP/BOOTP server with:
- DHCP-Option 66 (TFTP server name) pointing to a local TFTP
server within the same subnet of the DHCP range
- DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
of the to be booted image
3. Connect the port labeled internet to your local network
4. Keep the reset button pushed down and power on the board
The board should load and start the initramfs image from the TFTP
server. Login as root/without password to the started LEDE via SSH
listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE.
Revert to RouterOS
Use the "rbcfg" package on in LEDE:
- rbcfg set boot_protocol bootp
- rbcfg set boot_device ethnand
- rbcfg apply
Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.
Click on install again.
In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Ubiquiti UniFi APs just have eth0. Until now, the setup script fell
through to the default case and configured the (not present) eth1 as
WAN with DHCP.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
This patch adds support for the MikroTik RouterBOARD wAP
https://mikrotik.com/product/RBwAP2nD
Specifications:
- SoC: Qualcomm QCA9533 (650 MHz)
- RAM: 64 MB
- Storage: 16 MB NOR SPI flash
- Wireless: built-in QCA9533, 2x2:2
- Ethernet: 1x100M (802.3af/at POE in)
This patch adds missing code to fully support wAP. Machfile already
contained configuration for wAP 2nD but device specific configuration
like LEDs etc. was missing.
Installation:
1. Login to the Mikrotik WebUI to backup your licence keys
2. Setup a DHCP/BOOTP server with:
- DHCP-Option 66 (TFTP server name) pointing to a local TFTP
server within the same subnet of the DHCP range
- DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
of the to be booted image
3. Connect the port labeled internet to your local network
4. Keep the reset button pushed down and power on the board
The board should load and start the initramfs image from the TFTP
server. Login as root/without password to the started LEDE via SSH
listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE.
Revert to RouterOS
Use the "rbcfg" package on in LEDE:
- rbcfg set boot_protocol bootp
- rbcfg set boot_device ethnand
- rbcfg apply
Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.
Click on install again.
In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Wallys DR342 is a 5 GHz, 2T2R AP/CPE board based on Atheros AR9342.
Short specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 1x Gbps Ethernet (AR8035) with passive PoE support (24-56 V)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 5 GHz with external FEM (SKY85728-11), up to 30 dBm
- 2x MMCX connectors
- miniPCIe connector with PCIe and USB 2.0 buses
- optional miniSIM slot
- 7x LED, 1x button
- UART, (E)JTAG and LED headers
- 1x DC jack for main power (12-56 V)
Flash instruction (do it under U-Boot, using UART):
1. tftp 0x82000000 lede-ar71xx-generic-dr342-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
UniElec U7628-01 is a router platform board based on MediaTek MT7628AN.
The device has the following specifications:
- MT7628AN (580MHz)
- 64/128/256 MB of RAM (DDR2)
- 8/16 MB of flash (SPI NOR)
- 5x 10/100 Mbps Ethernet (MT7628 built-in switch)
- 1x 2T2R 2.4 GHz Wi-Fi (MT7628)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses)
- 1x miniSIM slot
- 1x microSD slot
- 1x USB 2.0 port
- 7x single-color LEDs (GPIO-controlled)
- 1x bi-color LED (green GPIO-controlled, red -> LED_WLAN# in miniPCIe)
- 1x reset button
- 1x UART header (4-pins)
- 1x SDXC/GPIO header (10-pins, connected with microSD slot)
- 1x DC jack for main power (12 V)
The following has been tested and is working:
- Ethernet switch
- miniPCIe slot (tested with modem and Wi-Fi card)
- miniSIM slot
- sysupgrade
- reset button
- USB 2.0 port*
Due to a missing driver (MMC over GPIO) this is not supported:
- microSD card reader
* Warning:
USB buses in miniPCIe and regular A-type socket are connected together,
without any proper analog switch or USB HUB.
Installation:
This board might come with a different firmware versions (MediaTek SDK,
PandoraBox, Padavan, etc.). If your board comes with PandoraBox, you can
install LEDE using sysupgrade. Just SSH to the router and perform forced
sysupgrade (due to a board name mismatch). The default IP of this board
should be: 192.168.1.1 and username/password: root/admin. In case of a
different firmware, you can use web based recovery described below.
Use the following command to perform the sysupgrade (for the 128MB
RAM/16MB flash version):
sysupgrade -n -F lede-ramips-mt76x8-u7628-01-128M-16M-squashfs-sysupgrade.bin
Recovery:
This board contains a Chinese, closed-source bootloader called Breed
(Boot and Recovery Environment for Embedded Devices). Breed supports web
recovery and to enter it, you keep the reset button pressed for around
5 seconds during boot. Your machine will be assigned an IP through DHCP
and the router will use IP address 192.168.1.1. The recovery website is
in Chinese, but is easy to use. Click on the second item in the list to
access the recovery page, then the second item on the next page is where
you select the firmware. In order to start the recovery, you click the
button at the bottom.
SDXC/GPIO header (J3):
1. SDXC_D3 / I2C_SCLK
2. SDXC_D2 / I2C_SD
3. SDXC_D1 / I2S_DI
4. SDXC_D0 / I2S_WS
5. SDXC_CMD / I2S_CLK
6. SDXC_CLK / GPIO0
7. SDXC_CD / UART_RXD1
8. UART_TXD1
9. 3V3
10. GND
Other notes:
1. The board is available with different amounts of RAM and flash. We
have only added support for the 128/16 MB configuration, as that seems
to be the default. However, all the required infrastructure is in place
for making support for the other configurations easy.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
UniElec U7621-06 is a router platform board based on MediaTek MT7621AT.
The device has the following specifications:
- MT7621AT (880 MHz)
- 256/512 MB of RAM (DDR3)
- 8/16/32/64 MB of FLASH (SPI NOR)
- 5x 1 Gbps Ethernet (MT7621 built-in switch)
- 1x ASMedia ASM1061 (for mSATA and SATA)
- 2x miniPCIe slots (PCIe bus only)
- 1x mSATA slot (with USB 2.0 bus for modem)
- 1x SATA
- 1x miniSIM slot
- 1x microSD slot
- 1x USB 3.0
- 12x LEDs (3 GPIO-controlled)
- 1x reset button
- 1x UART header (4-pins)
- 1x GPIO header (30-pins)
- 1x FPC connector for LEDs (20-pin, 0.5 mm pitch)
- 1x DC jack for main power (12 V)
The following has been tested and is working:
- Ethernet switch
- miniPCIe slots (tested with Wi-Fi cards)
- mSATA slot (tested with modem and mSATA drive)
- miniSIM slot
- sysupgrade
- reset button
- microSD slot
Installation:
This board might come with a different firmware versions (MediaTek SDK,
PandoraBox, Padavan, etc.). If your board comes with PandoraBox, you can
install LEDE using sysupgrade. Just SSH to the router and perform forced
sysupgrade (due to a board name mismatch). The default IP of this board
should be: 192.168.1.1 and username/password: root/admin. In case of a
different firmware, you can use web based recovery described below.
Use the following command to perform the sysupgrade (for the 256MB
RAM/16MB flash version):
sysupgrade -n -F lede-ramips-mt7621-u7621-06-256M-16M-squashfs-sysupgrade.bin
Recovery:
This board contains a Chinese, closed-source bootloader called Breed
(Boot and Recovery Environment for Embedded Devices). Breed supports web
recovery and to enter it, you keep the reset button pressed for around
5 seconds during boot. Your machine will be assigned an IP through DHCP
and the router will use IP address 192.168.1.1. The recovery website is
in Chinese, but is easy to use. Click on the second item in the list to
access the recovery page, then the second item on the next page is where
you select the firmware. In order to start the recovery, you click the
button at the bottom.
LEDs list (top row, left to right):
- LED_WWAN# (connected with pin 42 in LTE/mSATA slot)
- Power (connected directly to 3V3)
- CTS2_N (GPIO10, configured as "status" LED)
- TXD2 (GPIO11, configured as "led4", without default trigger)
- RXD2 (GPIO12, configured as "led5", without default trigger)
- LED_WLAN# (connected with pin 44 in wifi0 slot)
LEDs list (bottom row, left to right):
- ESW_P0_LED_0
- ESW_P1_LED_0
- ESW_P2_LED_0
- ESW_P3_LED_0
- ESW_P4_LED_0
- LED_WLAN# (connected with pin 44 in wifi1 slot)
Other notes:
1. The board is available with different amounts of RAM and flash. We
have only added support for the 256/16 MB configuration, as that seems
to be the default. However, all the required infrastructure is in place
for making support for the other configurations easy.
2. The manufacturer offers five different wireless cards with MediaTek
chipsets, based on MT76x2, MT7603 and MT7615. Images of the board all
show that the miniPCIe slots are dedicated to specific Wi-Fi cards.
However, the slots are generic.
3. All boards we got access to had the same EEPROM content. The default
firmware reads the Ethernet MAC from offset 0xe000 in factory partition.
This offset only contains 0xffs, so a random MAC will be generated on
every boot of the router. There is a valid MAC stored at offset 0xe006
and this MAC is shown as the WAN MAC in the bootloader. However, it is
the same on all boards we have checked. Based on information provided
by the vendor, all boards sold in small quantities are considered more
as samples for development purposes.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
This increases kernel partition size and fixes rootfs (file-system)
partition size on TP-Link RE450 v1. Also, while we are at it, switch
from statically defined kernel and rootfs partitions in kernel cmdline
to "tplink-fw" mtd splitter.
Fixes: FS#1072.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This patch increases kernel partition size and re-enables image
generation for below TP-Link boards:
- archer-c58-v1
- archer-c60-v1
- tl-wr902ac-v1
- tl-wr942n-v1
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[commit message and title reworded]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
