The Gateworks GW53xx family of products is based on the Freescale
i.MX6DL SoC and offers a small form-factor with peripherals such as:
* i.MX6DL
* NAND FLASH
* 4x PCIe
* 4x USB EHCI (1x front-panel; 3x PCIe sockets)
* 1x USB OTG
* 1x uSD
* LVDS connector (VLDS for display, PWM/GPIO for backlight, i2c for touch)
* HDMI Audio/Video out
* Analog Video in
* Digital IO
* Gateworks System Controller
* Accelerometer
* Canbus
* Optional GPS
* Industrial temp (-40C to +85C)
* DC input voltage 8 to 42V (Passive PoE and 802.3af)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 39012
DMA and SDMA support are needed for ssi based audio. Note that the sdma
firmware is no longer required for ssi audio.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 39011
Linaro GCC 4.6-2013.05 incorrectly pads the arpt_arp structure on
at least the ar71xx target, resulting in a two bytes shorter struct
in the kernel compared to what arptables userspace expects.
When comparing sizeof(struct arpt_arp) in kernel and userspace, the
former yields 162 byte, while the latter is 164 byte.
As a consequence, the subsequent target_offset and next_offset
members of the parent arpt_entry structure contain invalid values
when processed by the arptables binary, leading to bad memory
accesses in the populate_cache() procedure, subsequently causing a
segfault.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 38999
The wait instruction is only broken on the BCM4706 and not on the other
similar SoCs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38979
This sets both values to the OpenWrt default values. There is no reason
to use some brcm47xx specific values here.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38978
This adds support for vectored interrupts in this SoC.
This is supported by the 74K cpus.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38975
bcm47xx misses cpu overwrites for the features of the CPUs used in
these SoCs.
Instead of manually checking, it is now known at compile time for some
options and the compiler is able to remove the checks and optimize the
code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38974
Some time ago, after switching to the mainline bcm47xxpart driver
following patch has been applied:
commit 03cef8725d2062335ffc3de50fc037b294fd458c
Author: hauke <hauke@3c298f89-4303-0410-b956-a3cf2f4a3e73>
Date: Sat Apr 6 22:22:26 2013 +0000
brcm47xx: use old partition names again for kernel 3.8
This fixes sysupgrade. The partition names are used all over the Internet in various howtos.
Thank you russell for spotting this problem.
I propose to revert this change and make sysupgrade use "firmware"
instead. This makes brcm47xx compatible with widely used ar71xx and
after all "firmware" sounds like a much better name for... the firmware.
This change doesn't affect "sysupgrade" usage, because it never takes a
partition name as a parameter. This change only affects users using mtd
tool directly. Hopefully there are not many howtos using "mtd" command.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 38973
That function provides a slightly improved sanity check than the
currently used solution.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38967
This patch enables the convenient sysupgrade feature for
WD's Wi-Fi Range Extender.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Patchwork: http://patchwork.openwrt.org/patch/4341/
[juhosg:
- rename 'mynet_rext_check_image' function to 'cybertan_check_image'
and move that into platform.sh,
- remove the the model specific 'platform_do_upgrade_mynet_rext' function,
- drop the mynet-rext.sh script,
- remove the image/Makefile change,
- update commit message]
[christian:
- check all 8 bytes of the firmware/device magic]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38966
Make the Image/Build/CyberTAN macro more generic,
and use simple wrappers for the GZIP/LZMA variants.
This simplifies the Makefile a bit, and allows to
build sysupgrade images for the devices which are
using LZMA compressed uImages.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38965
In the current sysupgrade images, the CRC32 value of
the TRX header covers the whole rootfs data. Due to
this, the CRC value should be changed during sysupgrade
otherwise the bootloader refuses to load the image on
the next boot.
Change the image generation to create sysupgrade images
where the CRC32 value covers the kernel data only. This
allows to skip the 'fixtrx' step during sysupgrade on
the target.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38964
Argus ATP52B: ethernet didn't work because of unconfigured switch
Sparklan WCR150GN: add switch config and make single port to be LAN
Dlink DIR-645: seems to be a redundant case
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 38960
- partitions on factory fw are a bit strange
- unknown contained some strings in factory
- unknown2 contains some atheros (2nd art ?)
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Patchwork: http://patchwork.openwrt.org/patch/4149/
[juhosg: edit commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38954
There was no way to determine a working config, because
the switch (ar8337) was not working previously.
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Patchwork: http://patchwork.openwrt.org/patch/4470/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38953
This patch is needed to use the switch inside the Sitecom WLR-8100;
it was unusable and detected as Generic-Phy before.
since ar8337 is behaving like ar8327
generally do the same thing
see: https://forum.openwrt.org/viewtopic.php?pid=214218#p214218
forward-ported to trunk
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Patchwork: http://patchwork.openwrt.org/patch/4469/
[juhosg: merge chip_is_ar83[23]7 statements in ar8xxx_phy_config_init]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38952
The device has three extra LEDs which indicate the quality
of the wireless link. Thanks to rssileds, this feature now
works out of the box.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Patchwork: http://patchwork.openwrt.org/patch/4462/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38950
This patch improves support for the device considerably.
1. The wifi didn't work in the initial release. This was because
the WMAC of the AR9340 is not connected to the antennas.
(However, it can pick up wifi signals, if they are strong enough!)
Instead there's a dedicated AR9300 chip on the same board, which
works.
2. Ethernet throughput is improved. iperf shows that the hardware
can sustain more than 200Mbit/s and no longer drops any packages
when the link is under load.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Patchwork: http://patchwork.openwrt.org/patch/4461/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38949
The F1E Phy (AR8035?) requires additional bits to be
set in order to provide a fast and reliable connection
over gigabit links.
When enabled, the link doesn't suffer anymore from a small
package loss under load and the performance is improved
quite a bit as well. (203 mbit/s vs 112 mbit/s, iperf tcp).
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Patchwork: http://patchwork.openwrt.org/patch/4460/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38948
Small update to uci_defaults/01_leds, to support the usb led
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4426/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38947
Just a small oversight my part, added the support for the USB led
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4425/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38946
This patch fixes the NAPI poll mechanism in the GIANFAR ethernet driver, which
was not properly working since Linus Kernel Version 3,8.
Therefore the workaround patch to downgrade the GIANFAR ethernet driver to
Kernelversion v3.8 is obsoete.
This patch was extensivly testes with different network loads and types of
traffic. There is quite a substantial user base that reports proper Ethernet
function with TPlink-4900. This patch is based on the fixes from GINAFAR
maintainer Claudiu Manoli.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 38865
get_cycles() is used in some places as one part of the seed for the
kernel PRNG.
This backports the following commit from mainline linux kernel:
9c9b415c50bc298ac61412dff856eae2f54889ee
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38834
