Commits since last 2017-07-11:
4bd8601 pkg_parse: fix segfault when parsing descriptions with leading newlines
Fixes FS#933.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Fix incorrect offset and size of linux partition.
Fixes: 97b36aca09 ("brcm63xx: add pflash for remaining pflash equipped boards")
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The kernel 4.4 patches where already removed with the bump to 4.9. Drop
the the subtarget configs as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The WMDR-143N is a small module originally used as a Wifi client
in some Loewe smart TV sets. It is sold cheaply at german surplus
shops. The module contains a RT3662 SOC.
Specifications:
- 500 MHz CPU Clock
- 1x 10/100Mbps Ethernet (pin header)
- 32 MB of RAM
- 8 MB of FLASH
- 2T3R 2.4/5 GHz (SOC internal)
- 3 Antennas on PCB
- UART pads on PCB (J3: 1 = +3.3V, 2 = RX, 3 = TX, 4 = GND), TX
and RX are 3,3V only! The square hole is pin 1
- Power supply pads on PCB (J6: 1 and 2 = +5V, 3 and 4 = GND)
The square hole is pin 1
The original firmware has two identical kernel/rootfs images and
two "Factory" calibration data blocks in flash. The LEDE image
leaves only the first "Factory" block in place and uses both
"Kernel" blocks and the redundant "Factory" block together to gain
enough space for the jffs2 partition.
Flash instructions:
You need UART and Ethernet connections to flash the board. Use
the LEDE "sysupgrade.bin" image with tftp.
Apply power to the board and in the first 5 seconds, hit 2 to
select TFTP upload. The bootloader asks for board- and server IP
addresses and filename.
Alternate method: With the vendor firmware running, assign an IP
address to the ethernet port, tftp the firmware image to
/tmp and write to mtd4 ("KernelA").
Signed-off-by: Oliver Fleischmann <ogf@bnv-bamberg.de>
[remove pinctrl node from dts, no pin is used as GPIO]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Children of the pinctrl0 node are optional. Return EINVAL (=missing)
instead of 0. Fixes a hang if the pinctrl0 has no children.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: John Crispin <john@phrozen.org>
When a package declares a PKG_BUILD_DEPENDENCY or HOST_BUILD_DEPENDENCY on
a not existing build type, the metadata script will emit a reference to an
unresolvable build target in tmp/.packagedeps, causing the make process to
fail hard in a way not catchable by the IGNORE_ERRORS mechanism.
In a situation where a package "test-a" declares a build dependency
"PKG_BUILD_DEPENDS:=test-b/host" while the Makefile of "test-b" does not
implement a HostBuild, make fails with an unrecoverable error in the form:
make[1]: Entering directory '...'
make[1]: *** No rule to make target 'package/test-b/host/compile',
needed by 'package/test-a/compile'. Stop.
make[1]: Leaving directory '...'
.../toplevel.mk:200: recipe for target 'package/test-a/compile' failed
make: *** [package/test-a/compile] Error 2
Extend the metadata generation script to catch such unresolved references
and emit a visable warning upon detection.
After this change, the script will emit a warning similar to:
WARNING: Makefile "package/test-a/Makefile" has a build dependency on
"test-b/host" but "package/test-b/Makefile" does not implement a
"host" build type
Fixes a global build cluster outage which occured after the "python-cffi"
feed package removed its HostBuild which the "python-cryptography" package
build-depended on.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
there were 2 bugs
*) core1 came up with a bad bogo mips, looks like the clock needed time to stabilize
*) HPT frequency was not set making r4k timers not come up properly
Signed-off-by: John Crispin <john@phrozen.org>
The GnuBee Personal Cloud One crowdfunded on https://www.crowdsupply.com
It is a low-cost, low-power, network-attached storage device.
Specifications:
- SoC: MediaTek MT7621AT
- RAM: DDR3 512 MB
- Flash: 32 MB
- Six SATA ports for 2.5" Drives
- One micro SDcard
- One USB 3.0
- Two USB 2.0
- Gigabit Ethernet: 1 x WAN and 1 x LAN
- UART 3.5mm Audio Jack or 3 pin header - 57600 8N1
- Four GPIOs available on a pin header
Flash instructions:
The GnuBee Personal Cloud One ships with libreCMC installed.
libreCMC is a Free Software Foundation approved fork of LEDE/OpenWrt.
As such one can upgrade using the webinterface or sysupgrade.
Das U-Boot has multiple options for recovery or updates including :
- USB
- http
- tftp
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
[use switchdev led trigger, all interfaces are in vlan1; rename leds
according to board.d setting; remove ge2 group from the pinmux, this
group doesn't exist in the driver]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Luci shows switch ports in inverted order on that device.
This patch fixes switch port numbering and matches them to the device
silkscreen.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
The tftp and irc netfilter modules are provided by nf-nathelper-extra
and not by nf-nathelper.
Signed-off-by: Uwe Arnold <donvipre@gmail.com>
[move the irc module as well]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The VoCore2 features 128MB of RAM, therefore set
memory in DTS to 128*1024*1024 = 0x8000000
The board's LED is connected to GND, set it to
ACTIVE_HIGH here.
Make serial console working again on kernel 4.9 by
change of pinmux configuration.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
The TP-Link RE350 is a wall-wart AC1200 range extender/access point with
a single gigabit ethernet port and two non-detachable antennas, based on
the MT7621A SoC with MT7603E and MT7612E radios.
Firmware wise it is very similar to the QCA based RE450.
SoC: MediaTek MT7621A (880MHz)
Flash: 8MiB (Winbond W25Q64)
RAM: 64MiB (DDR2)
Ethernet: 1x 1Gbit
Wireless: 2T2R 2.4Ghz (MT7603E) and 5GHz (MT7612E)
LEDs: Power, 2.4G, 5G (blue), WPS (red and blue), ethernet link/act
(green)
Buttons: On/off, LED, reset, WPS
Serial header at J1, 57600 8n1:
Pin 1 TX
Pin 2 RX
Pin 3 GND
Pin 4 3.3V
Factory image can be uploaded directly through the stock UI.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
Only mangle argv[0] of the first executed process and leave the argument
vector of subsequent invocations as-is to allow child programs to properly
discover resources relative to their binary locations.
Fixes "cc1" discovery when executing the host gcc through the bundled
"ccache" executable.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The flag needs to be cleared for the last packet in the list, not the
first one. Fixes some issues with multicast packet loss for powersave
clients connected to an ath9k AP.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
FCC regulatory rules allow for up to 3 dBi antenna gain. Account for
this in the EEPROM based tx power reduction code.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
As we can now use combined mode in "mktplinkfw" tool to generate the
same header/image, this tool is no longer needed.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
We will need "mktplinkfw-combined" command also in the "ramips" target
for new MediaTek based TP-Link devices, with "safeloader" image type.
Also, rename the command to "tplink-v1-header", use "VERSION_DIST"
variable instead of "OpenWrt" and allow passing additional parameters.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
We use combined option in "mktplinkfw" tool for generating initramfs
kernel images and header for kernel inside "safeloader" image type (in
fact, only for TL-WR1043ND v4 at this moment).
There is also "mktplinkfw-kernel" tool, a stripped-down version, used
only for generating "simple" header, for safeloader image types.
This changes how "mktplinkfw" handles combined images (which then will
allow us to drop the stripped-down version of the tool):
- drop "ignore size" command line option (it was used only for combined
images anyway)
- don't require "flash layout id" for combined images (we don't need and
shouldn't limit size of the initramfs kernel and for kernels inside
safeloader images, the "tplink-safeloader" tool does the size check)
- require kernel address and entry point in command line parameters for
combined images (consequence of previous point)
- don't include md5 sum and firmware length values in header (they are
needed only for update from vendor GUI and are ingored in case of
initramfs and "tplink-safeloader" images)
- drop "fake" flash layout for TL-WR1043ND v4 as it's no longer needed
Also, adjust "mktplinkfw-combined" command in ar71xx/image/tp-link.mk to
match introduced changes in "mktplinkfw" tool.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network AP121F is a pocket-size router dedicated for VPN/TOR users.
Device is based on Atheros AR9331 WiSoC and is running a custom version
(updated from OpenWrt CC to LEDE 17.01 release) of NetAidKit firmware.
Specification:
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR1)
- 16 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz
- 1x microSD (optional, on separate PCB)
- 3x LED, 1x button, 1x switch
- UART header on PCB
Flash instruction (under U-Boot web recovery mode):
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with RJ45 port, press the reset button, power up device,
wait for first blink of all LEDs (indicates network setup), then keep
button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Browseable is now set through LuCI per share, so remove it. Same with
writeable (inverted synonym for read only). domain master and preferred
master seem to be legacy settings for Windows 9x. encrypt passwords
defaults to yes. Probably should not be disabled either.
Also reordered alphabetically.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[rewrap commit message, fix SoB, fix author, bump pkg revsion]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This change currently causes some issues with loading out of tree kernel modules
so revert that commit for now.
Reverts commit 34c01e68b5. Fixes FS#919.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Intent is to link against it, and have the option to
not install the ipset utility (if needed).
One example/use-case is keepalived (from package)
feeds, where it would be nice to just depend on a
`libipset` (sub)package.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Introduce a new UCI list setting `list dhcp_option_force` which is available
in sections of type `dnsmasq` and `dhcp`.
The `dhcp_option_force` setting has the same semantics as `dhcp_option` but
generates `dhcp-option-force` directives instead of `dhcp-option` ones in
emitted native configuration.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Internet2 isn't considered a trusted issuer meaning that https links to
rit.edu will fail.
The host mirror.csclub.uwaterloo.ca has a trusted SSL cert and peering
is good so it can replace rit.edu without performance issues.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
[Jo-Philipp Wich: rewrapped commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Commit 72d751cba9 "build: rework library bundling" introduced a new helper
binary "runas" whose sole purpose was mangling the argv vector passed to
the actual called ELF image so that the renamed executable could obtain the
proper name from argv[0].
This approach, however totally defeated the purpose of calling bundled ELF
executables through the shipped ld.so loader since the execv() invocation
performed by "runas" would cause the kernel the interprete the final program
image through the system ELF loader again.
To solve the problem, use an alternative approach of shipping a shared object
"runas.so" which uses an ELF ".init_array" function pointer to obtain the
argv[] vector of the to-be-executed main() function and mangle it in-place.
The actual argv[0] value to use is communicated out-of-band using an
environment variable "RUNAS_ARG0" by the shell wrapper script. The wrapper
script also takes care of setting LD_PRELOAD to instruct the shipped ELF
loader to preload the actual ELF program image with the "runas.so" helper
library.
Fixes FS#909.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
On Asus RT-N12 and RT-N16 models, the WAN and LAN4 ports are swapped in the
initial switch configuration since the presets present in nvram appear to be
wrong.
Add special casing for these models to detect_by_model() in order to ensure
a proper switch configuration.
Fixes FS#502.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
When processes don't die on SIGKILL (usually because of kernel bugs), it's
better to give up instead of looping forever.
upgraded will trigger a reboot in this case (and if this fails, a hardware
watchdog will eventually time out and reset the system, if present).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The Power LED of RB912UAG-{2,5}HPnD boards can be controlled by sofware,
so use it for diag purposes and make the User LED free for other tasks.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
It is quite unexpected behaviour when the Power LED switches off as soon
as the kernel starts booting. So set the default state to 'Keep' for
the Power LEDs of all RouterBOARDs (e.g. RB91x, SXT Lite series, etc.).
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
[switch the default state to keep instead of on]
Signed-off-by: Mathias Kresin <dev@kresin.me>
It uses one MT7615D radio chip with DBDC mode enabled. This mode allows
this single chip act as an 2x2 11n radio and an 2x2 11ac radio at the
same time. However mt76 doesn't support it currently so there is no
wireless available.
Specification:
- SoC: MediaTek MT7621AT
- Flash: 16 MB
- RAM: 128 MB
- Ethernet: 1 x WAN (10/100/1000Mbps) and 4 x LAN (10/100/1000 Mbps)
- Wireless radio: MT7615D on PCIE0
- UART: 1 x UART on PCB - 57600 8N1
Issue:
- Wireless radio doesn't work due to the lack of driver.
Flash instruction:
Using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART line as described on the PCB.
4. Power up the device and press 2,then follow the instruction to
set device and tftp server IP address and input the firmware
file name.U-boot will then load the firmware and write it into
the flash.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
In the xrx200_close() function we call napi_disable(), that could
sleep, with priv->hw->chan[i].lock held. This could lead to deadlock
and causes the kernel to complain.
Look at the code I couldn't convince myself about why we
need to protect that specific code part with the lock. IMHO there
seems no reason to protect the refcount variables, because AFAIK
ndo_close() and ndo_open() callbacks are already called with a
semaphore held. Neither I could figure out why napi_disable() have to
be called with that lock held. The only remaining code part for
which I could guess the lock is useful for is ltq_dma_close()
function call.
This patch reduces the lock to the said function call, avoiding the
sleep-with-spinlock-held situation
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
[fold into 0025-NET-MIPS-lantiq-adds-xrx200-net.patch, backport to
kernel 4.4]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Builtin modules are always present, and trying to load them will cause
modprobe to spew errors when installing the empty kmod packages.
Fix this by never generating any postinst module install instructions
for builtin modules.
Fixes#842.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Backport upstream commit f44f1e7da7c8e3f4575d5d61c4df978496903fcc ("um:
Avoid longjmp/setjmp symbol clashes with libpthread.a") to fix build
issues on hosts that only have a static libpthread.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
arc-2017.03 is the most recent release toolchain for ARC cores
and it is based on upstream Binutils 2.28 and GCC 6.3.0
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: John Crispin <john@phrozen.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Remove ping check in DHCPDISCOVER case as too many buggy clients leave
an interface in configured state causing the ping check to fail.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Expat release 2.2.2 requires support for either syscall(SYS_getrandom) which
is available on Linux 3.17 or support for getrandom() which is only available
in glibc 2.25 or later.
Since some of our builders still run on Linux 3.16, we need to forcibly
disable the use of getrandom() for the host builds.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
