All compiled device tree files not mentioned are binary identical to the
former ones.
Fix the obvious decimal/hex confusion for the power key of ramips/M2M.dts.
Due to the include of the input binding header, the BTN_* node names in:
- ramips/GL-MT300A.dts
- ramips/GL-MT300N.dts
- ramips/GL-MT750.dts
- ramips/Timecloud.dts
will be changed by the compiler to the numerical equivalent.
Move the binding include of lantiq boards to the file where they are
used the first time to hint the user where the values do come from.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Fixes invalid device tree parameters.
Drop the mvsw61xx node used in mvebu device tree source files. It looks
like some kind of ethernet switch cargo cult. Neither the
marvell,88e6352 nor the marvell,88e6172 compatible strings can be found
in any LEDE file or in the kernel sources.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Assign an unused MAC addresses to the 2.4GHz wifi interface as it was
originally planed but not possible.
The MAC address numbering of the TEW-691GR changes to the following
pattern:
LAN: AA:BB:CC:DD:EE:0C
WIFI: AA:BB:CC:DD:EE:0D
WAN: AA:BB:CC:DD:EE:0F
The MAC address numbering of the TEW-692GR changes to the following
pattern:
LAN: AA:BB:CC:DD:EE:e4
WAN: AA:BB:CC:DD:EE:e5
2.4GHz: AA:BB:CC:DD:EE:e7
5 GHz: AA:BB:CC:DD:EE:e8
Set the label and compatible string for the TEW-692GR PCIe wireless
according to the the PCI binding documentation.
Use the wifi@0,0 label and the pci0,0 compatible string since the PCI
vendor and device id is unknown. It should work anyway since the
compatible string isn't evaluated (yet).
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the ralink,mtd-eeprom instead of invoking the userspace firmware
loader.
Set the label and compatible string according to the the PCI binding
documentation.
Use the wifi@0,0 label and the pci0,0 compatible string in case the
PCI vendor and device id is unknown. It should work anyway since the
compatible string isn't evaluated (yet).
This commit might fixes the PCIe wireless for the Buffalo WHR-600D.
This board was mentioned in the board 10-rt2x00-eeprom firmware hotplug
script but never had the correct eeprom name set to trigger the
firmware from flash extraction.
Use the usual eeprom for the soc wmac of the Dovado Tiny AC.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The MikroTik hEX v3 (RB750Gr3) is a MT7621AT board which is similar to most MT7621 reference designs, it can be easily supported by this patch; however, the stock RouterBOOT bootloader has to be replaced by a MT7621 SDK U-Boot such as https://github.com/ndoo/RB750Gr3-U-Boot - U-Boot configured for the RB750Gr3 (16MiB SPI flash, 256MiB DDR3 RAM at 1200MHz).
RouterBOOT, the stock bootloader, does not initialize the UART and boots silently, making it preferable to replace it with a MT7621 SDK U-Boot with UART (57600 8N1) that supports HTTP, TFTP or serial upload of sysupgrade firmware and U-Boot.
Furthermore, RouterOS, the stock firmware, is contained in a proprietary modification of SquashFS without GPL sources; UART is also disabled in stock firmware.
The combination of LEDE firmware generated by this PR and MT7621 SDK U-Boot expects the printed MAC address to reside at offset `0xe000` of the factory partition (absolute offset is `0x4e000`); this is similar to the factory MAC address offset for several other MT7621 devices.
A 16MiB flash dump suitable for use with flashrom will be provided if/once this patch is accepted and binaries are built by LEDE buildbot. Alternatively, writing the U-Boot to the SPI flash starting at 0x0 offset and booting the board with serial console attached will allow TFTP, HTTP or serial upload of sysupgrade firmware.
Signed-off-by: Andrew Yong <me@ndoo.sg>
- setting read-only flag to important partitions
- enabling PA to improve 2.4 GHz signal strength
- add missing leds
- rename colour led
- add mac adress to 5GHz wlan interface
- included <dt-bindings/input/input.h> and <dt-bindings/gpio/gpio.h>
Signed-off-by: Henryk Heisig hyniu@o2.pl
All of the touched boards don't have an ethernet port. Allow to use the
wps button on these boards to enable the wireless radio after boot.
The force enabled wireless for the DCH-M225 is removed. It is reckless
to bring up an unencrypted wireless network by default these days.
Using the wps button to bring up the radio seam to me the better
approach.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Assign the reset functionality to the wps/reset buttons. Use the wlan
switch of the 6200n to enable/disable wlan.
Add the internet led of the 6200nl and use the led for boot status
indication
Signed-off-by: Mathias Kresin <dev@kresin.me>
With 3a9752bbd2 and later changes to
ramips_set_preinit_iface() the default vlan config applied during
preinit was changed. These changes were made without updating the
default network config to ensure that vlan interfaces used for lan/wan
are still configured.
Fix the issue by using the default all LAN portmap and disabling not
connected switch ports using portdisable device tree parameter.
Signed-off-by: Mathias Kresin <dev@kresin.me>
applied bb-final-ramips-add-zyxel-nbg-419n2.patch from
123serge123, found at https://yadi.sk/d/1ZV0lKJwbTE65;
see https://forum.openwrt.org/viewtopic.php?pid=246905#p246905,
modified slightly to fit to CC release and to new lede build
system: image/rt305x.mk include file is used now
changed NBG-419N2.dts format to fit style of other dts files
Signed-off-by: Klaus <k-laus@quantentunnel.de>
- CPU: MT7620A 580MHz
- Flash: 8MB - RAM: 64MB
- External PA+LNA on both WLAN2.4 and WLAN5
- 4x LAN ethernet and 1x WAN ethernet
Signed-off-by: Xuefu Lin <xuefulin@gmail.com>
Due to the missing phy-mode setting, the switch wasn't initialised.
The wireless requires an eeprom to work. Use the same mac addresses as
the stock firmware.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The AR8327 initvals were not copied to the DTS during the switch from
mach file to device tree and broke the switch on the device.
The former used PORT6 related initvals were wrong and have been
corrected.
The phy mode setting for the switch was missing in the DTS as well.
The wireless requires an eeprom to work. The dual band wireless chips
have both bands enabled by default but only one band per chip is
working.
The stock firmware uses the following mac addresses:
LAN: AA:BB:CC:DD:EE:E4
WAN: AA:BB:CC:DD:EE:E4
2.4GHz: AA:BB:CC:DD:EE:E4
5 GHz: AA:BB:CC:DD:EE:E8
Assuming the mac address range :E4 to :E8 is reserved for this device,
the MAC addresses were reorder to have a unique MAC address for each
interface:
LAN: AA:BB:CC:DD:EE:E4
2.4GHz: AA:BB:CC:DD:EE:E4
WAN: AA:BB:CC:DD:EE:E5
5 GHz: AA:BB:CC:DD:EE:E8
Signed-off-by: Mathias Kresin <dev@kresin.me>
Fixes the following compiler warning:
Warning (reg_format): "reg" property in /ethernet@10100000/port@0 has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /ethernet@10100000/port@0
Warning (avoid_default_addr_size): Relying on default #size-cells value for /ethernet@10100000/port@0
Signed-off-by: Mathias Kresin <dev@kresin.me>
Thunder Timecloud is a small NAS with MT7621A. It has 1 USB port and an
SD Card slot. There is no wireless cards.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
D-Link DCH-M225 is based on Mediatek MT7620 with 64MB ram, 8MB flash,
3.5mm audio out support. but no ethernet and usb ports.
so you must default enable wifi.
Signed-off-by: Michael Lee <igvtee@gmail.com>
The NixCore X1 is a Ralink/MediaTek rt5350 WiFi Module.
http://nixcores.com/
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: Drew Gaylo <drew@nixcores.com>
The partition size is wrong, leading to out-of-disk-space even on no/moderate use.
Upstream fix from vendor: 2f25eb57ed
Suggested fix for openwrt: https://dev.openwrt.org/ticket/20321
Signed-off-by: Rene Treffer <treffer@measite.de>
Pinmux for rgmii needs to be set to rgmii, not gpio.
Hide the ESW switch on boot (using new rgmii esw devicetree attribute).
Also add a Sitecom-specific profile, since the image needs to include
the rtl8366 kernel driver.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
The ZBT APE522II is a dual-radio outdoor CPE based on the MT7620a SoC. It has
64 MB RAM, 8 MB flash, 2 Fast Ethernet ports via internal switch (one with
802.3af 48V PoE support), a 802.11b/g/n SoC 2.4 GHz radio and an 802.11a/n/ac
MT7612E-based 5 GHz radio.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
DuZun DM06 is a develop board based on mt7628
64M RAM, 8M SPI Flash, 1 WAN, 1 LAN.
wm8960 codec with line out, line in and speaker output.
Signed-off-by: Michael Lee <igvtee@gmail.com>
The Widora board is similar to the Linkit 7688 but features a larger flash
capacity.
Signed-off-by: Yuan Chenmang <771992497@qq.com>
[Jo-Philipp Wich: Reword commit message, cleanup initial PR]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Currently, for RT5350 and MT7628, esw is marked as compatible with
"ralink,rt3050-esw". While this is true, the switches within RT5350
and MT7628 actually support more functionality than the RT3050 switch.
One such example is per-VLAN untagging, which is an important feature.
RT3352 is another example of this, but it already has an additional
compatible property, which allows to differentiate it from RT3050.
This commit adds such more specific properties for RT5350 and MT7628
as well.
Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
- disable all ethernet ports except port 0 on MPR-A2
Port 0 is the only ethernet port on this router, so disable all other PHYs in order to save power.
- don't use a VLAN for the single ethernet port of the MPR-A2
Like A5-V11, this router only has one ethernet port.
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
This commit makes the following modifications to ramips dts files:
1. Add clkctrl node to all dtsi files (although not used for now)
2. Add clocks and clock-names properties to some nodes (usbphy, pci)
3. Add usbphy node for rt3050 (although not used for now)
4. Add clock-frequency to uart nodes in mt7621.dtsi and mt7628an.dtsi
These modifications, although not fully used at the moment, will make
it easier for FreeBSD to adopt and use LEDE ramips dts files with
minimal changes for easier maintenance.
Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
Add node aliases to dtsi files.
Reword dts files so they're more in-line with upstream.
Fix some more warnings and errors reported by dtc
Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
This patch introduces serial0 aliases in the ramips DTS files, which can
then be used to denote the active console instead of relying on bootargs.
Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
Port 0 is the only ethernet port on this router, so disable all other PHYs
in order to save power.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 49292
Port 4 is the only ethernet port on this router, so disable all other PHYs
in order to save power.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 49291
add support for Planex MZK-EX750NP.
MZK-EX750NP is MT7620A and MT7610E based 11ac wifi repeater.
Built-in power supply.
64MiB RAM, 8MiB SPI Flash, non Wired Ethernet.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 49268
CS-QR10 is MT7620A based IP Camera.
the camera and sound does not work with kernel 4.4.
- camera chip is sn9c291.
- sound chip is wm8960.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 49234
The WG3526 is the follow-up to the 2626 and is mostly the same, with the
excaption that the mt7602 has been replaced with the mt7603. The internal wifi
setup has also changed slightly. Based on my tests, everything that worked on
the 2626 works on the 3526 and with roughly the same performance.
v1->v2:
* Remove some references to 2626 that I had missed in the dts.
v2->v3:
* Update patch to match new file structure.
* Removed SD driver to be consistent with other MT7621 targets.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
SVN-Revision: 49213
ELECOM WRH-300CR is MT7620N based very small Wi-Fi router with 64MiB
DDR2 SDRAM, 16MiB SPI Flash, one fast ethernet port, and (internal but
easy-to-access) UART.
it also has internal USB hub and USB card reader which provide one USB
port, one SD card slot, and one microSD card slot.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
SVN-Revision: 49211
update DTS files to use jedec,spi-nor compatible string for m25p80 to fix probe issues.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 49209
Misc fixes for LinkIt 7688 board:
- Copy the right wireless firmware for the mt7688
- Add back '0065-mt7688-fixes.patch', left out after the move to Linux 4.4.
- Remove SPI_DEV from linux config which otherwise causes a massive warning
- Add wmac to LINKIT7688.dts so wireless works
Signed-off-by: Adam Kent <adam@semicircular.net>
SVN-Revision: 49130
1) Use leds to indicate:
Red - Power
Amber - Radio On
Blue - Wifi associated
2) Add profile to default build group for MT7628 subtarget
Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com>
SVN-Revision: 49045
Xiaomi MiWiFi Nano is based on Mediatek MT7628 with 64MB ram 16MB flash
Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com>
v3 includes changes suggested by L. D. Pinney & Karl Palsson-
Eliminate en25q64 (4MB) flash chip
Alphabetization
Remove hyphen in model
Rename profile from miwifinano.mk to xiaomi.mk
Add gpios that are attached to leds
SVN-Revision: 49024
This patch adds support for GL-MT750.
GL-MT750 is powered by MT7620A and MT7610e, dual band 802.11ac, 2.4G 300Mbps and 5G 450Mbps.
It has 5 LANs, MMC interface, USB, a lot of IOs and PoE support.
SVN-Revision: 48994
This patch adds support for GL-MT300N.
GL-MT300N is powered by MT7620N with 16MB flash, 64MB RAM,
2 LANs, USB, UART, GPIO and PoE support.
SVN-Revision: 48993
This patches adds support for GL-MT300A.
GL-MT300A is powered by MT7620A. It has 16MB flash, 128MB RAM,
Two LANs, USB, UART and MMC daughter board.
SVN-Revision: 48992
add support for Planex MZK-WDPR.
MZK-WDPR(MZK-WDPR-R01) is internet radio tuner.
This patch is "network board" in MZK-WDPR.
LCD board is non OpenWrt Platform.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 48968
Add a device tree for JCG JHR-N825R
This router is based on a RT3052 and has 4MB of CFI flash and 32MB of
SDRAM. As a special feature, it comes with a two digit seven segment
display that is connected to a pair of daisy-chained 74164 shift
registers that can be controlled via GPIOs.
For details, see https://wikidevi.com/wiki/JCG_JHR-N825R .
Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>
SVN-Revision: 48904
Add a device tree for JCG JHR-N825R
This router is based on a RT3052 and has 4MB of CFI flash and 32MB of
SDRAM. For details, see https://wikidevi.com/wiki/JCG_JHR-N825R .
Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>
SVN-Revision: 48903
Add a device tree for JCG JHR-N805R
This router is based on a RT3050 and has 4MB of SPI flash and 16MB of
SDRAM. For details, see https://wikidevi.com/wiki/JCG_JHR-N805R .
Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>
SVN-Revision: 48902
Hi,
the board in subject (RT5350F-OLinuXino-EVB) still ships from vendor
with a RC3 image built upon a .dts file which declares GPIO12 and GPIO14
as relay2 and relay1 respectively, as you can see from their rt5350f
branch on GitHub.
For some reason in the official stable build both the GPIOs are swapped
and the wrong names are declared in the gpio-export directive.
I'm submitting this patch which should roll back the wrong changes, so
that we get backward compatibility with any script developed on RC3
which controls the relays.
After patching correct operation is restored:
root@OpenWrt:/# cat /sys/kernel/debug/gpio
GPIOs 0-21, platform/10000600.gpio, 10000600.gpio:
gpio-0 (button ) in hi
gpio-12 (relay2 ) out lo
gpio-14 (relay1 ) out lo
Thank you,
Signed-off-by: Lorenzo Cafaro <lorenzo@ibisco.net>
SVN-Revision: 48796
- Fix typo in board_data partition start address
- Increase board_data partition size in order to exploit all flash size
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
SVN-Revision: 48751
This patch adds support for Phicomm PSG1208.This is a router with MT7620A SoC with 8M flash and 64M ram.
The WPS led is uesd as status_led because the power light can't be controlled with GPIO.
It seems that the 5g wifi led is connected to MT7612E and it can't be controlled with GPIO too.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
SVN-Revision: 48721
This patch adds support for the Netgear EX2700 and builds an approriate
sysupgrade image.
What's missing is the option to build a factory image flashable via the
router's stock web interface, but this approach is hindered by the fact
that u-boot operforms an additional integrity check, which expects a
uImage header in the last 64 bytes of the "kernel" partition, which
the bootloader expects to be 960k, a size exceeded by the standard
OpenWrt kernel.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
SVN-Revision: 48698
The top half of UARTF on the HLK-RM04 is used for GPIO.
mode 1 mode 2
RIN GPIO14
DSR_N GPIO13
DCD_N GPIO12
DTR_N GPIO11
RXD GPIO10
CTS_N GPIO09
TXD GPIO08
RTS_N GPIO07
This patch applies 3'b101 mode to UARTF:
GPIO14
GPIO13
GPIO12
GPIO11
RXD
CTS_N
TXD
RTS_N
Because the base rt5350.dtsi file forces 3'b000 mode, remove the pin setting from this file and apply it directly to the files that inherit from it (WIZFI630A.dts and WT1520.dtsi). This change makes the rt5350.dtsi file consistent with the mt7620a.dtsi file.
Signed-off-by: John Clark <inindev@gmail.com>
SVN-Revision: 48665
The I2C function of the RT5350 SoC on the HLK-RM04 is used for GPIO1 and GPIO2.
Take note that the I2C_SD pin is GPIO1 on the RT5350 and is exposed on the HLK-RM04 as GPIO0
Likewise the I2C_SCLK pin is GPIO2 on the RT5350 and is exposed on the HLK-RM04 as GPIO1
group mode 1 mode 2 hlk-rm04 pin & export
i2c i2c_sd gpio1 (pin 8, hlk-rm04:gpio0)
i2c i2c_sclk gpio2 (pin 9, hlk-rm04:gpio1)
reference:
http://www.hlktech.net/product_detail.php?ProId=39http://cdn.sparkfun.com/datasheets/Wireless/WiFi/RT5350.pdf
Signed-off-by: John Clark <inindev@gmail.com>
SVN-Revision: 48664
The RESET button of the HLK-RM04 is connected to GPIO0, linux function 0x198
The WPS button of the HLK-RM04 is connected to GPIO14, linux function 0x211
Signed-off-by: John Clark <inindev@gmail.com>
SVN-Revision: 48663
The power LED on the HLK-RM04 is hard wired to the power bus and is not under GPIO control, remove the bogus config for it.
(Note that GPIO0 is actually connected to the RESET button.)
Signed-off-by: John Clark <inindev@gmail.com>
SVN-Revision: 48662
The bootloader was updated and now uses 115200 instead of 57600 baud
for the serial console. Change this also in OpenWrt's DTS, so the rate
is consistent for bootloader and linux kernel output.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 48359
LED's were defined wrong in the device tree file, they are hardware driven because they are connected directly to the switch chip and wireless chips respectively, thus no GPIO addresses are assigned to them. It is safe to remove them from the device tree file to stop confusion.
Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>
SVN-Revision: 48055
This router is based on MT7621 SoC, no wifi, no usb, nand.
Works:
* Boots.
* Ethernet.
* Switch.
* Button (reset).
* Flashing OpenWrt from stock firmware.
* Upgrading OpenWrt.
Doesn't work:
* No GPIO leds. All leds are controlled by switch,
but stock firmware was able to control them.
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
nand/spi drivers do not support pin sharing,
so it is not accessable and disabled. Stock
firmware could read it and it was empty.
* PoE out.
Router has serial pins populated. If looking at the top
of the router, then counting from Eth sockets pins go as:
'GND, RX, TX, GND'. 3.3v, 57600.
U-boot bootloader supports tftpboot, controlled from serial.
This router has two kernel partitions: 'live' and 'backup'.
They are swapped during flashing (on both stock and OpenWrt).
Active partition is controlled by a flag in a factory partition.
U-boot has custom command to switch active kernel partition.
Kernel partitions are 'bare flash' 3MB. Stock bootloader has
no UBI support. Stock rootfs is UBIFS.
Flashing procedure.
Stock firmware uses custom kernel patch to mount squashfs
from a file that is located on UBIFS volume. This makes wiping
out this volume from within stock firmware difficult.
Instead this patch builds image that is flashable by stock firmware
and contains initrams image (with minimal set of packages
to fit into kernel partition). Once this is flashed one can reboot
into initramfs OpenWrt and use sysupgrade to flash OpenWrt including
rootfs into nand.
Note: factory image is only built if initramfs image is enabled.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47881
Partitions defined in parent dtsi cannot be undefined in children.
This moves partitions defined in mt7621.dtsi into board's device tree.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47876
* Switches clocksource to gic timer.
* Moves frequency definitions to dtsi since frequency was hardcoded anyway
Will work on proper frequency detection later.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47875
The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram,
2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and
one 5 ghz antenna.
This is the 6th submission that adds support for XHCI in the device tree
file, along with switching the location of the 2 radio's and addition of
the kmod-i2c-mt7621 in the default packages of the profile.
Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>
SVN-Revision: 47845
The PBR-M1 support in current OpenWrt is for the early demo board and it doesn't work on the final board.This patch fixes the support for it.
The LED called pbr-m1:buzzer is a beeper connected to GPIO26 so I used gpio-beeper instead of gpio-leds.
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 47844
* Switches clocksource to gic timer.
* Moves frequency definitions to dtsi since frequency was hardcoded anyway
Will work on proper frequency detection later.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47843
Enables CPS multiprocessing instead ob obsoleted CMP for mt7621.
This patch fixes a few issues currently existing on 4.3 kernel with at least ubnt-erx:
* iperf shows only 50Mbits on direct gigabit connection to desktop,
* ping times jump to 5-6ms to dorectly connected desktop
* /proc/interrupts shows spurious interrups (ERR)
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47842
netis WF-2881 is an MT7621AT based router with MT7602EN, MT7612EN.
It has 128MB DDR3, 128MB SLC NAND FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.
this device only works on top of UBI.
Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons (reset button)
* ethernet switch and USB diag LEDs
* UART
* GPIOs
* sysupgrade
Tested and not working
* failsafe
Signed-off-by: YounJae Rho <luxflow@live.com>
SVN-Revision: 47619
Changes since V1:
I resend this patch for current trunk.The former V1 patch is for CC branch.
Signed-off-by: Shonn Lu <countrysideboy@qq.com>
SVN-Revision: 47617
This patch adds the eeprom property to the dts for the Asus RP-N53. It is necessary to get the wifi in the soc working.
Signed-off-by: Alberto Mattea <alberto@mattea.info>
SVN-Revision: 47350
Add support for Dovado tiny AC wifi router.
Soc: mt7620a
ram: 64MB
flash: 8MB
1x usb 2.0
two gigabit lan ports
5ghz wlan is not supported on this board since there is no gpl driverfor mt7610e wifi chip.
Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>
SVN-Revision: 47348
add the SDK alsa driver. this has only been tested on mt7628/88 and wm8960.
mt7620 is only compile tested.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 47205
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.
The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.
v3 fix
1: Merged most stuff into dtsi file
2: Remove unnecessary empty lines.
Signed-off-by: Xiaoning Kang <kangxn@163.com>
SVN-Revision: 47112
The pinctrl-rt2880 code doesn't support multiple functions with the same
name. This will result in a incorrect pinmux configuration.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46963
This patch is to add the WIZnet WizFi630A board as a new platform. The board is in mini pci express form factor.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
SVN-Revision: 46921
This patch add support for Planex DB-WRT01. DANBOARD route on
the MT7620A SoC with two Ethernet port and a 802.11n 2.4 GHz radio.
DANBOARD is Cartoon character.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 46918
The upstream LED naming convention is "device:color:led-name", but it seems that many of supported boards in OpenWrt don't follow this approach.
The following patch fixes this inconsistency in dts{,i} files and updates base-files scripts for ramips target:
* fixes wrong indentation
* keeps case statements structure in same convention as in other scripts (no empty line after ";;", no indentation for case...esac body)
* fixes wrong LED names for some of boards (makes them the same as in dts{,i} files)
* combines boards with same configuration (ex. set_wifi_led "rt2800pci-phy0::radio" in 01_leds)
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46664
The following patch changes 7Links PX-4885 dts{,i} filenames, board, image and profile names from "PX4885" to "PX-4885" (for consistency).
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46629
The following patch changes Buffalo WMR-300 dts filename, board, image and profile names from "WMR300" to "WMR-300" (for consistency).
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46628
The following patch changes dts filename and profile name for Aigale Ai-BR100 (for consistency).
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46624
Official names for RT5350F based OLinuXino products are "RT5350F-OLinuXino{,-EVB}" as on official manufacturer website.
The following patch:
* changes board names from "olinuxino-rt5350f{,-evb}" to "rt5350f-olinuxino{,-evb}"
* changes filenames of dts and profile files
* changes image filenames
for Olimex RT5350F-OLinuXino{,-EVB} devices.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46623
The following patch changes:
* board name from "wl341v3" to "wl-341v3"
* dts filename
* LED names in dts file
for Sitecom WL-341v3 device.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46622
The following patch:
* changes board name from "argus-atp52b" to "atp-52b"
* changes dts filename
* fixes LED names in dts file and base-files scripts
* removes manufacturer name from image filename
for Argus ATP-52B device.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46621
Other Asus RT-N dts files are named "RT-N..." (not "RTN..."), so use the same for RT-N56U.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46619
The following patch:
* changes board name from "xiaomi-miwifi-mini" to "miwifi-mini"
* changes filenames of dts and profile
* fixes LED names in dts file and base-files scripts
* removes manufacturer name from image filename
for Xiaomi MiWiFi Mini device.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46617
There are other Asus boards supported in ramips target, so use the same naming scheme for WL-330N{,3G} boards and their dts files.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46615
There is another Zbtlink board (ZBT-WA05) supported in ramips target, so use the same naming scheme for ZBT-WR8305RT board and its dts file.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46614
The following patch fixes:
* wrong indentations
* doubled gpio-keys-polled nodes (DIR-300-B7, DIR-320-B1, DIR-610-A1)
* duplicate spacings
* empty lines at end of files and after last child nodes
* trailing and leading whitespace
* unnecessary and commented-out code
* missing empty lines between nodes and between properties and nodes
* unnecessary empty lines between nodes properties [1]
in .dts{,i} files, for ramips target.
[1] Some of empty lines in SOCs dtsi files were left untouched, because they seem to be there for a reason (readability?).
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46613
STORYLiNK SAP-G3200U3 is an AC1200 router based on MT7621AT+MT7602EN+MT7612EN.
It has 128MB DDR3, 8MB NOR FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.
Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons
* ethernet switch and USB diag LEDs
* UART
* GPIOs
Tested and not working:
* LEDs for WiFi radios (connected with WiFi chips, not supported in mt76?)
* failsafe mode (known problem, needs workaround like other MTK based devices)
More information in Wiki: http://wiki.openwrt.org/toh/storylink/sap-g3200u3
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46454
This patch add support for Planex MZK-DP150N.
a mini router on the MT7620A SoC with one Ethernet port and a 802.11n 2.4 GHz radio.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 46405
Adding support for OY-0001 Wireless Router.
OY-0001 is a wireless router made by oyewifi.com. Below is the details:
MT7620A, 128MB DDR2, 16MB FLASH, SD Slot, USB 2.0, 4 x LAN + 1 x WAN.
Signed-off-by: Tom Deng <2579131212@qq.com>
SVN-Revision: 46349
USB port of TP-Link Archer C20i does not work with trunk and CC.
This patch adds two nodes (ehci and ohci) to the device tree enabling USB.
Signed-off-by: Gunnar Thorburn <gunnar@thorburn.se>
SVN-Revision: 46348
This patch adds support for the Linksys RE6500 Range Extender
http://wiki.openwrt.org/toh/linksys/re6500
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 46043
This patch is for PandoraBox PBR-M1 which is based on mt7621,
all the features work fine, including rtc, leds, button, usb3.0, etc.
Signed-off-by: tymon <banglang.huang@foxmail.com>
SVN-Revision: 46041
Version 2 : White spaces and alphabetical order problems
fixed
Support for Olimex RT5350F-OLinuXino Boards, tested with RT5350F-OLinuXino and RT5350F-OLinuXino-EVB boards. More Info :
https://www.olimex.com/Products/OLinuXino/RT5350F/RT5350F-OLinuXino/open-source-hardware
Signed-off-by: Dimitar Gamishev HeHoPMaJIeH <gamishev@gmail.com>
SVN-Revision: 45902
Avoid the use of memory marked as reserved
MT7621 support 512MB memory.
According to "MT7621_ProgrammingGuide_Preliminary_Platform.pdf"
0x0~0x1c000000 448MB
0x20000000~0x4000000 64MB
total 512MB
Signed-off-by: wengbj <fl.service@t-firefly.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45892
MR-102N is a RT3050F based wireless router(32M RAM + 8M NOR flash) with 1 USB
and 1 ethernet port. The original product information can be found at:
http://www.aximcom.com/en/MR-102N
Signed-off-by: Tai-hwa Liang <atliang@gmail.com>
SVN-Revision: 45724
This patch adds support for Comfast CF-WR800N, a wall-plug wireless router
based on the MT7620N SoC with one Ethernet port and a 802.11n 2.4 GHz radio.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 45722
MicroWRT is an wireless router with 2 USB,1 ethernet port. It
has a 16M flash and 64M DDR2 RAM. You can use most interface, such as
i2c, SPI, i2s and PCIe. Besides that there are three expansion borad to
combine with the core board. The detailed information, please refer to
https://www.microduino.cc/wiki/index.php?title=Main_Page
This patch adds support for it.
Because there is only one port,so disabled VLAN and use eth0 as lan
port. and only a power LED control by power pin.
Signed-off-by: 盛凯 <shengkai81@gmail.com>
SVN-Revision: 45331
ZTE Q7 is a wireless router with SD Card,USB,1 ethernet port and a battery.It used MT7620a SoC.
I can,t find any information about this router on ZTE's website.
But I found this : http://en.cctairmobi.com/plus/list.php?tid=40
This router is the same as ZTE Q7 and later I found that both routers are made by the same company:-D
This patch adds support for it.
Because there is only one port,I disabled VLAN and use eth0 as lan port.
I could only create a sysupgrade firmware because I don't know how the orignal webpage check the uploaded image:-(
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 45208
I got work with this patch.
Ethernet switch (includes VLAN), WiFi connected via PCIe, LEDs, buttons.
In mtd partion map of DTS file, I renamed Linux firmware regions (kernel + root squashfs) to “firmware”because it allows kernel to split kernel and roots and rootfsdata.
signed-off-by: ngc@ff.iij4u.or.jp
——
——
SVN-Revision: 44470
MLW221 dts use tabs NOT spaces.
MLWG2 dts typo and 1 tab not spaces
01_leds and diag.sh cleanup
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 44356
This patch sets the correct location of the mt76 radio in the pcie bridge
(pcie-bridge instead of pcie0). Additionaly, it disables the 2.4 GHz band.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 44355
Both Y1 and Y1S have MT7612E wireless chip so I submitted this patch.
Tested on Lenovo Y1.
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 44354
This patch adds support for Xiaomi MiWiFi Mini, a 802.11a/b/g/n/ac dual radio
wireless router based on the MediaTek MT7620a SoC.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 44238
This patch is a follow up for my previous patch:
"ramips: add support for Intenso Memory 2 Move USB 3.0".
It fixes a couple of errors in the DTS (one of which broke
the gpio-buttons). The kmod-leds-gpio dependency has been
dropped as it is already part of the ramips target.
Furthermore the ramdisk/uImage image is generated by default
for the rt3050 subtarget. This image is needed to flash
OpenWrt for the first time onto the device via TFTP.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44072
This adds support for a rt5350-based "portable nas" solution
from Intenso. The board comes with 32M RAM and 8M Flash, the
built-in HDD is connected/accessible via a usb3.0<->sata
bridge VLI VL701.
The device has 1 Ethernet port (100M/10M), 1 micro b usb 3.0
socket (for charging the battery, or accessing the hdd directly).
Wireless connectivity is provided by the rt5350 SoC [i.e.:
802.11n 1x1 2.4 GHz with a pcb antenna.]
Serial, leds, wifi, ethernet and usb are tested and
as far as I can tell: they are working fine (tm).
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44001
- Fix LED definitions.
- Add mode-switch slider definition (at GPIO 14).
- Remove unneeded VLAN now that the ethernet driver is fixed and TCP packets get passed correctly now. (This router only has one port.)
- Fix LAN port MAC address, which is defined in the factory partition as WLAN MAC address + 1.
- Fix board name, as the company name is HooToo and not HOOTOO.
- Remove unnecessary packages from the profile. (The end-user is supposed to use mechanisms such as the ImageBuilder in order to add his own set of packages to his own images... while the precompiled images should just contain the core set of packages needed to run the base functions of a wireless router.)
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 43883
Aigale Ai-BR100 is a router with mt7620a soc.
There are only 2 lights on the board (WAN and WLAN) so I used the wlan light as the status led.
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 43681
some old mt7620a uboots dont reset the pcie core properly. work around this
issue in the kernel driver.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43292
* read MAC address from factory partition
* remove port defines since there is only one port (most likely C/P error)
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 43231
r43200 tries to detect if the fixup is needed or not. control the behaviour via
OF instead and disable unused ports.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43201
This is a RT2880-based board, 32MB RAM, 4MB flash. The bootloader
is a hacked u-Boot that reads an LZMA image directly, so we skip
generating the uImage header and enable the lzma mtdsplit parser.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 43153
(Reposted due to an issue with the patchwork server during original submission)
Unbranded. Silkscreen on PCB is “A5-V11”, believed to be made by Bococom (or at least uses Bococom image encryption - as used on poray devices - but different key)
Signed-off-by: Gareth Bryan <gareth@mx9.org>
SVN-Revision: 43102
7Links PX-4885 (clones) can also be purchased with 8MB flash.
Creating images for these routers, use dtsi for common part
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 42892
Provides support for the Tripmate HT-TM02 personal router including LEDs and
reset button. “Mode” switch is not supported. New profile includes full set
of packages required to enable LEDs, USB, and LUCI. Patches were applied
against trunk snapshot r42649. Functionality has been tested in AP, basic wifi
client, wifi router, and routed client modes - all good.
Signed-off-by: Ron Curry <wingspinner@gmail.com>
SVN-Revision: 42785
