safed one level of indention by using 'continue' instead of a
lengthy if-clause.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
v2: use logic-AND instead of '?' operator when checking for hw bug 6320
SVN-Revision: 43768
- replaced // comments by /* comments */
- added line-breaks where needed
- fixed white-space according to kernel style
- fixed some obvious spelling mistakes in comments and printks
- removed some unneeded left-overs imported from vendor code-base
- replaced printk(...) by libata macros where possible
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43767
locking for 2nd port and hwraid was added from vendor's GPL code which
doesn't comply with current kernel coding style.
- moved all global variables into host_priv
- renamed locks
- sanetized acquire() and release() parameter list
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43766
and no longer compile-in ext4 filesystem now that sata_oxnas is
also built as a module.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43765
Set defaults health led to a timer heartbeet (200/800)
and populate network for:
- GuruplugServerPlus
- SheevaPlug
- SheevaPlug with eSATA
Signed-off-by: Gerald Kerma <dreagle@doukki.net>
SVN-Revision: 43752
This maps the LAN ports to eth0 and WAN port to eth1.
Since there are two interfaces the 802.1q VLAN mode
is unnecessary and left disabled. Port-based VLANs
are used instead.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 43750
When there is no device connected to the controller we should not start
the controller. This also changes between PCIe 1.0 and PCIe 2.0 speed
based on the device. This code is based on code from the new Broadcom
PCIe controller driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43748
This patch adds soc support for QCA9561 and TP9343.
TP9343 is a reduced version of QCA9561, which can be found in TP-LINK routers in China.
The qca956x_wmac has not yet been supported by ath9k.
tested on TL-WDR6500 and TL-WR882N v1 (Chinese version)
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 43744
Remove read/write/rmw member functions from ar8xxx_priv
There seems to be no real benefit of the ar8xxx_priv member functions
read/write/rmw as one implementation exists for each of them only.
Especially ar8xxx_mii_rmw is assigned to priv->rmw first and then
mapped to ar8xxx_rmw.
Rename the ar8xxx_mii_.. functions to ar8xxx_.. and use them directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43742
Create helpers mii_read32 / mii_write32 for 32 bit MII ops.
Rename r3 variable to page in ar8xxx_mii_write to make it consistent
with the other ar8xxx_mii_xxxx functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43741
Factor out chip-specific parameters from ar8xxx_probe_switch.
Move the ar8xxx_chip definitions after the swops definitions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43740
This new argument is used right after starting regular preinit (which
happens if failsafe wasn't triggered). The main purpose of "preinit"
argument is to indicate that failsafe can be triggered, however we were
missing a way to inform user that we don't wait for a trigger anymore.
With this change it's clear when failsafe mode can be triggered.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43715
