Commit graph

43 commits

Author SHA1 Message Date
John Crispin
6cbb1be464 ramips: Fix support for PBR-M1 board
The PBR-M1 support in current OpenWrt is for the early demo board and it doesn't work on the final board.This patch fixes the support for it.

The LED called pbr-m1:buzzer is a beeper connected to GPIO26 so I used gpio-beeper instead of gpio-leds.

Signed-off-by: 郭传鈜 <gch981213@gmail.com>

SVN-Revision: 47844
2015-12-11 15:03:50 +00:00
Jo-Philipp Wich
ecf5b4fab7 ramips: hg255d: replace ucidef_set_led_interface() with ucidef_set_led_netdev()
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47657
2015-11-26 12:46:04 +00:00
John Crispin
8c1f5141ce ralink: add support for netis WF-2881
netis WF-2881 is an MT7621AT based router with MT7602EN, MT7612EN.
It has 128MB DDR3, 128MB SLC NAND FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.

this device only works on top of UBI.

Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons (reset button)
* ethernet switch and USB diag LEDs
* UART
* GPIOs
* sysupgrade

Tested and not working
* failsafe

Signed-off-by: YounJae Rho <luxflow@live.com>

SVN-Revision: 47619
2015-11-24 18:29:26 +00:00
John Crispin
e9baf8265b ramips: add support for Youku YK1
Changes since V1:
I resend this patch for current trunk.The former V1 patch is for CC branch.

Signed-off-by: Shonn Lu <countrysideboy@qq.com>

SVN-Revision: 47617
2015-11-24 18:29:02 +00:00
John Crispin
3760b95702 ramips: add support for Dovado tiny AC
Add support for Dovado tiny AC wifi router.

Soc: mt7620a
ram: 64MB
flash: 8MB
1x usb 2.0
two gigabit lan ports

5ghz wlan is not supported on this board since there is no gpl driverfor mt7610e wifi chip.

Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>

SVN-Revision: 47348
2015-11-02 10:17:51 +00:00
John Crispin
c10bdf11ff ramips: Add base-files for HiWiFi HC5x61 models
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.

The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.

v3 fix
   1: Fixed model order
   2: Remove manufacturer name from model name
   3: Use a hacky but prettier way to get mac address.

Signed-off-by: Xiaoning Kang <kangxn@163.com>

SVN-Revision: 47111
2015-10-05 10:25:47 +00:00
John Crispin
2efdc7c896 ramips: add support for Planex DB-WRT01
This patch add support for Planex DB-WRT01. DANBOARD route on
 the MT7620A SoC with two Ethernet port and a 802.11n 2.4 GHz radio.
 DANBOARD is Cartoon character.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 46918
2015-09-14 20:08:55 +00:00
John Crispin
0f155a330e ramips: base-files: optimize etc/diag.sh and etc/board.d/01_leds scripts
Instead of using board name provided explicitly as text in LED name, ex.:

[...]
mlwg2)
	status_led="mlwg2:blue:system"
[...]

use $board variable, which allows to combine together multiple boards with same color and LED names, ex:

[...]
mlw221|\
mlwg2)
	status_led="$board:blue:system"
[...]

The above approach allows to shrink size of code in base-files/etc/board.d/01_leds and base-files/etc/diag.sh scripts dramatically.
One thing to keep in mind here is that we assume to use proper and consistent LED naming scheme ("device:color:led-name").

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46665
2015-08-17 06:24:47 +00:00
John Crispin
1a392636a5 ramips: use consistent naming scheme for LEDs
The upstream LED naming convention is "device:color:led-name", but it seems that many of supported boards in OpenWrt don't follow this approach.
The following patch fixes this inconsistency in dts{,i} files and updates base-files scripts for ramips target:
 * fixes wrong indentation
 * keeps case statements structure in same convention as in other scripts (no empty line after ";;", no indentation for case...esac body)
 * fixes wrong LED names for some of boards (makes them the same as in dts{,i} files)
 * combines boards with same configuration (ex. set_wifi_led "rt2800pci-phy0::radio" in 01_leds)

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46664
2015-08-17 06:24:34 +00:00
John Crispin
0d464c360f ramips: remove old code for Edimax BR-6524N
It seems that support for Edimax BR-6524N was dropped long time ago (dts file for this device is missing).
This patch removes remaining code.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46630
2015-08-17 06:01:23 +00:00
John Crispin
2fe5cf2bd6 ramips: fix 7Links PX-4885 dts{, i}, board, image and profile names
The following patch changes 7Links PX-4885 dts{,i} filenames, board, image and profile names from "PX4885" to "PX-4885" (for consistency).

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46629
2015-08-17 06:01:06 +00:00
John Crispin
713c81e97b ramips: fix Omnima models, images and profiles names
Official names for supported Omnima products are (as on website):
 * Omnima HPM
 * Omnima MiniEMBWiFi
 * Omnima MiniEMBPlug

This patch changes:
 * board names
 * dts filenames
 * profile names
 * image filenames
 * LED names

for Omnima devices, for consistency.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46627
2015-08-17 06:00:11 +00:00
John Crispin
0bb270429d ramips: fix Edimax BR-6425 board name
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46626
2015-08-17 05:59:57 +00:00
John Crispin
a0b8c60134 ramips: fix Xiaomi MiWiFi Mini board, image and profile names
The following patch:
 * changes board name from "xiaomi-miwifi-mini" to "miwifi-mini"
 * changes filenames of dts and profile
 * fixes LED names in dts file and base-files scripts
 * removes manufacturer name from image filename

for Xiaomi MiWiFi Mini device.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46617
2015-08-17 05:58:15 +00:00
John Crispin
f38db77707 ramips: fix Zbtlink ZBT-WR8305RT board name
There is another Zbtlink board (ZBT-WA05) supported in ramips target, so use the same naming scheme for ZBT-WR8305RT board and its dts file.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46614
2015-08-17 05:57:41 +00:00
John Crispin
dcae3723fd ramips: add support for STORYLiNK SAP-G3200U3
STORYLiNK SAP-G3200U3 is an AC1200 router based on MT7621AT+MT7602EN+MT7612EN.
It has 128MB DDR3, 8MB NOR FLASH, 5-port Gbps switch and 1x USB 3.0.

The following patch adds support for this device.

Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons
* ethernet switch and USB diag LEDs
* UART
* GPIOs

Tested and not working:
* LEDs for WiFi radios (connected with WiFi chips, not supported in mt76?)
* failsafe mode (known problem, needs workaround like other MTK based devices)

More information in Wiki: http://wiki.openwrt.org/toh/storylink/sap-g3200u3

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46454
2015-07-24 09:09:22 +00:00
John Crispin
eff79253f2 ramips: add support for Planex MZK-DP150N
This patch add support for Planex MZK-DP150N.
a mini router on the MT7620A SoC with one Ethernet port and a 802.11n 2.4 GHz radio.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 46405
2015-07-17 12:51:08 +00:00
John Crispin
b618573815 ramips: adding support for OY-0001 Wireless Router
Adding support for OY-0001 Wireless Router.
OY-0001 is a wireless router made by oyewifi.com. Below is the details:
MT7620A, 128MB DDR2, 16MB FLASH, SD Slot, USB 2.0, 4 x LAN + 1 x WAN.

Signed-off-by: Tom Deng <2579131212@qq.com>

SVN-Revision: 46349
2015-07-14 07:40:22 +00:00
John Crispin
cf1fb25e67 ramips: Add Support for the Linksys RE6500
This patch adds support for the Linksys RE6500 Range Extender

http://wiki.openwrt.org/toh/linksys/re6500

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 46043
2015-06-18 18:20:56 +00:00
John Crispin
e26ba31f76 ramips: Add support for the D-Link DCS-930 B1
http://wiki.openwrt.org/toh/d-link/dcs-930l

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 46042
2015-06-18 18:20:46 +00:00
John Crispin
640b211b1e ramips: add support for PandoraBox PBR-M1
This patch is for PandoraBox PBR-M1 which is based on mt7621,
all the features work fine, including rtc, leds, button, usb3.0, etc.

Signed-off-by: tymon <banglang.huang@foxmail.com>

SVN-Revision: 46041
2015-06-18 18:20:40 +00:00
John Crispin
9c86abae0e ramips: Adding support for AXIMCom MR-102N 3G/4G Travel Mobile Router
MR-102N is a RT3050F based wireless router(32M RAM + 8M NOR flash) with 1 USB
and 1 ethernet port.  The original product information can be found at:
http://www.aximcom.com/en/MR-102N

Signed-off-by:	Tai-hwa Liang <atliang@gmail.com>

SVN-Revision: 45724
2015-05-23 15:27:05 +00:00
John Crispin
5e96c2d541 ramips: add support for Comfast CF-WR800N
This patch adds support for Comfast CF-WR800N, a wall-plug wireless router
based on the MT7620N SoC with one Ethernet port and a 802.11n 2.4 GHz radio.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>

SVN-Revision: 45722
2015-05-23 15:26:39 +00:00
John Crispin
449c5f7b30 ramips: Add support for ZTE Q7
ZTE Q7 is a wireless router with SD Card,USB,1 ethernet port and a battery.It used MT7620a SoC.
I can,t find any information about this router on ZTE's website.
But I found this : http://en.cctairmobi.com/plus/list.php?tid=40
This router is the same as ZTE Q7 and later I found that both routers are made by the same company:-D

This patch adds support for it.
Because there is only one port,I disabled VLAN and use eth0 as lan port.
I could only create a sysupgrade firmware because I don't know how the orignal webpage check the uploaded image:-(

Signed-off-by: 郭传鈜 <gch981213@gmail.com>

SVN-Revision: 45208
2015-04-01 08:31:46 +00:00
John Crispin
4ce7053b2b ramips: Kingston MLW221 and MLWG2 cleanup
MLW221 dts use tabs NOT spaces.
MLWG2 dts typo and 1 tab not spaces
01_leds and diag.sh cleanup

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 44356
2015-02-09 12:15:45 +00:00
John Crispin
70db4e4639 ramips: add support for Xiaomi MiWiFi Mini devices
This patch adds support for Xiaomi MiWiFi Mini, a 802.11a/b/g/n/ac dual radio
wireless router based on the MediaTek MT7620a SoC.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>

SVN-Revision: 44238
2015-02-02 09:01:07 +00:00
John Crispin
36d19e46df ramips: add support for Tenda 3G150B
Add suport for Tenda 3G150B:
- cpu: Ralink RT5350F
- flash: 4MB
- ram: 32MB
- 1x USB 2.0
- 1x RJ45
- one reset button
- battery powered (BP-4L, 3.7V 1450mAh)

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 44073
2015-01-22 09:35:22 +00:00
John Crispin
88df2bd2ff ramips: add support for Intenso Memory 2 Move USB 3.0
This adds support for a rt5350-based "portable nas" solution
from Intenso. The board comes with 32M RAM and 8M Flash, the
built-in HDD is connected/accessible via a usb3.0<->sata
bridge VLI VL701.

The device has 1 Ethernet port (100M/10M), 1 micro b usb 3.0
socket (for charging the battery, or accessing the hdd directly).
Wireless connectivity is provided by the rt5350 SoC [i.e.:
802.11n 1x1 2.4 GHz with a pcb antenna.]

Serial, leds, wifi, ethernet and usb are tested and
as far as I can tell: they are working fine (tm).

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

SVN-Revision: 44001
2015-01-17 14:06:13 +00:00
John Crispin
7a65864344 ralink: add support for Kingston MLWG2
This patch adds support for the Kingston Mobilelite Wireless G2 (MLWG2)

http://wiki.openwrt.org/toh/kingston/mlwg2

https://github.com/gmacario/kingston-mlwg2-hack/wiki/Testing-OpenWrt-on-MLWG2

Tested-by: Gianpaolo Macario <gmacario@gmail.com>

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 43990
2015-01-17 07:07:36 +00:00
John Crispin
27b82a7990 ramips: fix default led configuration for rt-n14u
use new helper function to generate default led configuration

Signed-off-by: Pavel Löbl <lobl.pavel@gmail.com>

SVN-Revision: 43984
2015-01-17 07:06:51 +00:00
John Crispin
2120e48e75 ramips: Fix HooToo HT-TM02 support.
- Fix LED definitions.
- Add mode-switch slider definition (at GPIO 14).
- Remove unneeded VLAN now that the ethernet driver is fixed and TCP packets get passed correctly now. (This router only has one port.)
- Fix LAN port MAC address, which is defined in the factory partition as WLAN MAC address + 1.
- Fix board name, as the company name is HooToo and not HOOTOO.
- Remove unnecessary packages from the profile. (The end-user is supposed to use mechanisms such as the ImageBuilder in order to add his own set of packages to his own images... while the precompiled images should just contain the core set of packages needed to run the base functions of a wireless router.)

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 43883
2015-01-08 20:26:20 +00:00
John Crispin
f9dcd95919 ramips: base-files: Whitespace fixes.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 43880
2015-01-08 20:25:55 +00:00
John Crispin
263070a2e7 ramips:Add support for Aigale Ai-BR100
Aigale Ai-BR100 is a router with mt7620a soc.
There are only 2 lights on the board (WAN and WLAN) so I used the wlan light as the status led.

Signed-off-by: 郭传鈜 <gch981213@gmail.com>

SVN-Revision: 43681
2014-12-13 08:07:03 +00:00
John Crispin
cc5194cf03 ramips: add support for Airlink101 AR670W
This is a RT2880-based board, 32MB RAM, 4MB flash. The bootloader
is a hacked u-Boot that reads an LZMA image directly, so we skip
generating the uImage header and enable the lzma mtdsplit parser.

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 43153
2014-11-03 08:00:13 +00:00
John Crispin
d0bf15f235 ramips: add support for A5-V11 board (resubmit)
(Reposted due to an issue with the patchwork server during original submission)

Unbranded. Silkscreen on PCB is “A5-V11”, believed to be made by Bococom (or at least uses Bococom image encryption - as used on poray devices - but different key)

Signed-off-by: Gareth Bryan <gareth@mx9.org>

SVN-Revision: 43102
2014-10-29 11:01:17 +00:00
John Crispin
7bac455a4c ramips: add support for Nexx WT3020 devices
SVN-Revision: 42983
2014-10-20 06:28:48 +00:00
John Crispin
af1207b58c ramips: add support for Nexx WT1520
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>

SVN-Revision: 42867
2014-10-10 08:56:43 +00:00
John Crispin
d76b7e0221 ramips: D-Link DIR-810L: make led naming consistent with other boards
Signed-off-by: Michael Heimpold <mhei@heimpold.de>

SVN-Revision: 42789
2014-10-06 04:52:36 +00:00
John Crispin
b04bb3eea7 ramips: Support for RAMIPS based Tripmate HT-TM02 board
Provides support for the Tripmate HT-TM02 personal router including LEDs and
reset button. “Mode” switch is not supported. New profile includes full set
of packages required to enable LEDs, USB, and LUCI. Patches were applied
against trunk snapshot r42649. Functionality has been tested in AP, basic wifi
client, wifi router, and routed client modes - all good.

Signed-off-by: Ron Curry <wingspinner@gmail.com>

SVN-Revision: 42785
2014-10-06 04:52:07 +00:00
John Crispin
d4cc995c53 ramips: D-Link DIR-810L. Add support for SoC 2.4 GHz wireless and fix leds naming
SVN-Revision: 42619
2014-09-19 11:07:08 +00:00
John Crispin
ff3ea02772 ramips: add omni plug leds
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42201
2014-08-18 16:09:21 +00:00
John Crispin
bb9a23aca2 ramips: Hame: change LED name mpr-x -> hame
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 42190
2014-08-18 13:09:39 +00:00
John Crispin
0fc4383d69 ramips: make use of the new board detection layer
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42186
2014-08-18 13:09:20 +00:00
Renamed from target/linux/ramips/base-files/etc/uci-defaults/01_leds (Browse further)