Commit graph

670 commits

Author SHA1 Message Date
John Crispin
32e93efc73 target/linux/*: more dead package cleanups
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41571
2014-07-10 20:05:43 +00:00
John Crispin
0f76f8a16e target/linux/*: kmod-fs-ext{2,3} RIP
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41560
2014-07-10 19:16:15 +00:00
Hauke Mehrtens
0a5145e851 brcm47xx: make reboot a more reliable
A reboot is issued by setting the watchdog timer to a low value, when
the value is decreased from 1 to 0 by the hardware the system will
reboot. Setting this value to 1 does not work every time, it is a
little bit more reliable when setting it to 3. This timer runs with
some MHz or KHz so nobody will notice the increased waiting.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41548
2014-07-07 20:12:40 +00:00
Hauke Mehrtens
f42c36ea60 brcm47xx: add buttons support for Netgear WNR3500L
Ticket: #14406

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 41547
2014-07-07 19:14:22 +00:00
Hauke Mehrtens
4632347879 brcm47xx: remove unneeded images from generic target
broadcom-wl now builds in the mips74k profile, so remove these chips
from the generic profile.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41546
2014-07-07 17:47:24 +00:00
Hauke Mehrtens
3597b7d456 brcm47xx: image: legacy: take over old devices images
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 41530
2014-07-06 17:21:37 +00:00
Hauke Mehrtens
0eb3c26e7d brcm47xx: image: mips74k: take over some device images
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41529
2014-07-06 17:14:29 +00:00
Hauke Mehrtens
c3b3df1da8 brcm47xx: image: prepare for using mips74k subtarget
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 41528
2014-07-06 17:14:06 +00:00
Hauke Mehrtens
df8741f92b brcm47xx: fix bcm4705 rebooting when initializing the switch.
When the Ethernet controller is powered down and someone wants to
access the mdio bus like the witch driver (b53) the system crashed if
PCI_D3hot was set before. This patch deactivates this power sawing mode
when a switch driver is in use.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41527
2014-07-06 13:45:43 +00:00
Hauke Mehrtens
356663cdc8 brcm47xx: add LEDs for Netgear WNR3500L
https://dev.openwrt.org/ticket/14406

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41520
2014-07-05 23:25:26 +00:00
Hauke Mehrtens
8e4efd42d9 brcm47xx: make it possible to unregister the adm switch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41517
2014-07-05 21:35:15 +00:00
Hauke Mehrtens
03e2310a38 brcm47xx: fix LEDs on WRTSL54GS
https://dev.openwrt.org/ticket/16991

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41516
2014-07-05 19:40:15 +00:00
Hauke Mehrtens
77dee19ab4 brcm47xx: increase fallback mac addresses by one
Now the mac address is increased by two for the first fallback mac
address. It could be that the address increased should be used for the
wan port.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41515
2014-07-05 19:36:49 +00:00
Hauke Mehrtens
3fff38f93a brcm47xx: do not use mac addresses with 00:90:4C prefix, prevent mac address collisions.
The address prefix 00:90:4C is used by Broadcom in their initial
configuration. When a mac address with the prefix 00:90:4C is used
all devices from the same series are sharing the same mac address.
To prevent mac address collisions we replace them with a mac address
based on the base address.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41513
2014-07-05 15:04:50 +00:00
Hauke Mehrtens
163fe41c75 brcm47xx: get switch name from swconfig first
Without this patch the switch config for the adm switch did not worked,
because hey are not names eth0.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41512
2014-07-05 12:15:03 +00:00
Hauke Mehrtens
3f64bb8f8f brcm47xx: add LEDs for Asus RT-N15U and update RT-N66U
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 41501
2014-07-03 21:41:33 +00:00
Hauke Mehrtens
9467896172 brcm47xx: migrate basic network settings from old releases
Old OpenWrt releases were using network configs that are not valid
anymore. They were specifying ports tagging in a different way (or were
not tagging CPU at all) and were using VID 0 which is a reserved value.

Modifying network configuration to apply all needed changes would be
pretty tricky. Script /etc/init.d/netconfig that generates new config is
quite complex itself.
So instead let's save the most important settings, regenerate config
from the scratch and restore values. This should work for 99% of users.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 41500
2014-07-03 21:40:59 +00:00
Hauke Mehrtens
5996160a66 brcm47xx: add CONFIG_LEDS_GPIO_REGISTER
CONFIG_LEDS_GPIO_REGISTER is selected by the bcm47xx arch code.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41488
2014-07-02 22:07:46 +00:00
Hauke Mehrtens
f95fc5b2d5 brcm47xx: refresh patches
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41487
2014-07-02 22:03:03 +00:00
Hauke Mehrtens
ba1b49dbab brcm47xx: backport BCM47XX Linksys WRT54G series patches
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41486
2014-07-02 21:54:59 +00:00
John Crispin
994e5ce2f9 kernel: update 3.10.36->3.10.44
205-fix-headers_install.patch is obseleted by upstream commit 3246a0352e3d58380b9386570f1db1faf7edf8a8

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41351
2014-06-26 13:47:42 +00:00
Felix Fietkau
ad97acf46a brcm47xx: merge FEATURES lines in the legacy subtarget
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41053
2014-06-08 09:51:38 +00:00
Felix Fietkau
c48140efb8 brcm47xx: fix kmod-usb-brcm47xx build on legacy and mips74k subtargets
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41052
2014-06-08 09:45:55 +00:00
Hauke Mehrtens
ed7c73fbef brcm47xx: activate some compiler optimizations for 74K CPUs
With this patch the mips74k subtarget will be compiled with optimized
compiler options to generated smaller and faster code. This currently
breaks broadcom-wl, because the binary blob is only compiled with
mipsr1 support.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41050
2014-06-07 17:36:02 +00:00
Felix Fietkau
4b953aa267 brcm47xx: move the low_mem feature flag to the legacy subtarget
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41049
2014-06-07 17:21:30 +00:00
Hauke Mehrtens
717e8b6f3c brcm47xx: remove old gpio and nvram interfaces
These were only used by broadcom-diag any more.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41048
2014-06-07 17:04:37 +00:00
Hauke Mehrtens
cfa350ca39 brcm47xx: mips74k: optimize kernel config
This saves abount 15 kB of compressed kernel size.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41043
2014-06-07 15:42:33 +00:00
Hauke Mehrtens
9dc5fb9103 bcm47xx: use eth0 for switch name
This fixes some strange problems with tg3. I assume that the Ethernet
driver was not brought up if the switch was named switch0.

This was reported and tested by ernesto (Faulp3lz).

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41042
2014-06-07 15:41:41 +00:00
Felix Fietkau
dec0d7f025 brcm47xx: add a "legacy" subtarget that is usable for low-end 802.11g devices like WRT54G
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 41041
2014-06-07 15:19:40 +00:00
Hauke Mehrtens
bffd80e3e1 brcm47xx: add mips74k subtarget for newer devices
All new devices (with MIPS 74K CPU) are based on BCMA SoC and have
Ethernet core supported by bgmac. Create a new subtarget to generate
optimized builds.
This is just a beginning, further tweaks (like kernel configuration)
are still possible. This decreases default root.squashfs by ~128 kB.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41025
2014-06-05 21:25:03 +00:00
Hauke Mehrtens
b5d42bc111 brcm47xx: move current target to "generic" subtarget
This allows creating more subtargets and optimize builds per family.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 41024
2014-06-05 21:23:58 +00:00
Felix Fietkau
ae2c9a815a brcm47xx: enable the low-memory feature flag
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 40982
2014-06-02 17:04:45 +00:00
John Crispin
f933a741a9 target/linux/*/base-files/lib/upgrade/platform.sh - wrong check for ARGC
ARGC is a 'C-ism', but not known/valid in shell-syntax - insert the correct
var $# (=number of args) here. under normal conditions this had no impact,
but we should at least correct it. the error was observable like this:

root@box:~ [ -e "/etc/functions.sh" ] && . /etc/functions.sh
root@box:~ [ -e "/lib/functions.sh" ] && . /lib/functions.sh
root@box:~ . /lib/upgrade/platform.sh
root@box:~ . /lib/upgrade/common.sh
root@box:~ platform_check_image /tmp/myfirmware.bin
ash: bad number
root@box:~ echo $?
0

Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>

SVN-Revision: 40915
2014-06-02 12:43:22 +00:00
Felix Fietkau
32d1e0ed2c kernel: add a ssb backport required for a new mac80211 update
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 40833
2014-05-23 18:48:31 +00:00
Hauke Mehrtens
16b6db7055 brcm47xx: profiles: fix white spaces (s/ $//)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 40763
2014-05-14 10:09:31 +00:00
Hauke Mehrtens
1d878cabf2 brcm47xx: image: respect device flash block size
We should be more careful and don't generate 128K JFFS2 images for
devices with flashes using 64K blocks (nor the other way).

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 40762
2014-05-14 10:08:56 +00:00
Hauke Mehrtens
4cd010a712 brcm47xx: image: document some defines arguments
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 40761
2014-05-14 10:08:22 +00:00
Gabor Juhos
d2812cb036 kernel: update 3.10 to 3.10.36
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40467
2014-04-12 11:59:07 +00:00
Hauke Mehrtens
e99cfaaf95 brcm47xx: refresh patches
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 40425
2014-04-08 19:51:36 +00:00
Hauke Mehrtens
c286feac80 brcm47xx: backport 3.14 patch for nvram GPIO pin read
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 40346
2014-03-30 19:07:46 +00:00
Hauke Mehrtens
499d1f1401 brcm47xx: Name LEDs colors for Linksys E1000 V2.1
Handle it by creating a new patch for simple database changes.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 40345
2014-03-30 19:07:13 +00:00
Hauke Mehrtens
a1f4a43cef brcm47xx: update workarounds patch to V3
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 40344
2014-03-30 19:06:24 +00:00
Gabor Juhos
627baa28d3 kernel: update 3.10 to 3.10.34
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40291
2014-03-27 09:28:33 +00:00
Hauke Mehrtens
00dc53dd2e brcm47xx: add initial support for kernel 3.14
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 39905
2014-03-12 23:28:41 +00:00
Florian Fainelli
f71fa7d646 brcm47xx: explicitely mention MIPS to avoid confusion
And while at it, fix the nomenclature, BCM947xx/953xx refer to specific boards,
while BCM47xx/BCM53xx refer to chip identification number.

Signed-off-by: Florian Fainelli <florian@openwrt.org>

SVN-Revision: 39841
2014-03-08 01:48:44 +00:00
Hauke Mehrtens
5b388e5716 brcm47xx: b44: some fixes in combination with the switch
Let the switch start the carrier and set the duplex mode independently
if this nic is up of not.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 39733
2014-02-23 18:51:56 +00:00
Hauke Mehrtens
f587bacc26 brcm47xx: b44: start the phy
We did not start the PHY when an external phy was in use. Without this
patch the driver uses half duplex mode and the switch uses full duplex
mode, which causes problems.
Thank you fback for spotting this problem.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 39719
2014-02-23 16:58:12 +00:00
Hauke Mehrtens
15a7efa119 brcm47xx: fix detection of some Linksys WRT54G* devices
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 39718
2014-02-23 15:57:37 +00:00
Gabor Juhos
f677b1bc7e kernel: update 3.10 to 3.10.32
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39707
2014-02-23 10:59:40 +00:00
Hauke Mehrtens
2ad7e55a89 brcm47xx: new patch adding arch workarounds.c
It was recently sent to linux-mips for comments. It adds workaround for
WNR3500L to enable USB port.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 39469
2014-02-04 23:32:01 +00:00