added: ip addr, ip route, ip link, traceroute6
removed: hostid, devmem, vconfig, arping
deprecated (to be removed): ifconfig, route
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46829
Everything except for blkcipher was already built-in, so make blkcipher
built-in as well.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46820
While technically required by the RFC, they are usually completely
unused (DSA), or have security issues (3DES, CBC)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46814
This enables passworldless login for root via SSH whenever no root
password is set (e.g. after reset, flashing without keeping config
or in failsafe) and removes telnet support alltogether.
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46809
* ra: don't announce as default router if we aren't (regression)
* ra: reduce maximum announced dns lifetimes due to buggy clients
* dhcpv6: fix mac-based lease-matching
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46802
Without this patch adding the wifi device to the bridge may fail
because the bridge is not already configured when the wifi device gets
configured. This patch makes broadcom-wl wait till the bridge is ready.
This fixes#17262
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46749
Add CONFIG_IEEE80211W variable to DRIVER_MAKEOPTS so that 802.11w
support is properly compiled in full variant.
This fixes#20179
Signed-off-by: Janusz Dziemidowicz <rraptorr@nails.eu.org>
SVN-Revision: 46737
So far support for multiple interface was somehow broken in brcmfmac.
Driver couldn't correctly match firmware and system interfaces resulting
in not working APs and WARNINGs. This pending patches fixes that :)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46734
We sill don't use kernel 4.2 which is required for backporting using
upstream NVRAM support patch.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46724
The ipw2x00 drivers assume that the system they are running is little
endian, and access everything in native byte order. When run on a big
endian system, everything breaks apart.
Since fixing this is non trivial on a first glance, disable them for
big endian targets.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46708
The u-boot boot counter was never reset after a successful boot,
which sometimes could make some variables become out of sync.
This patch adds support for the boot counter and enables
auto_recovery unconditionally.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Rob Mosher <nyt-openwrt@countercultured.net>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 46690
Packages that depend on PolarSSL fail to build because polarssl's InstallDev
section never actually gets executed because (prior to this patch) the package
name does not match the subdir the package is in (presumably due to upstream
name change). As a workaround I have changed the package name back to
polarssl and used a new variable SRC_PKG_NAME for the purposes of downloading
the upstream tarball and creating PKG_BUILD_DIR.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 46683
firmware is not available in linux-firmware yet
so use official driver source
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 46682
Using the postinst script for sanity checks and expecting opkg to fail
if the postinst didn't return 0 was possible in Barrier Breaker, propagate
the real postinst return code through default_postinst to restore this
behaviour.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46653
Other VLAN related options are already being processed in netifd.sh
but the vlan_file option is missing. This option allows the mapping
of vlan IDs to network interfaces and will be used in dynamic VLAN
feature for binding stations to interfaces based on VLAN
assignments. The change is done similarly to the wpa_psk_file
option.
Signed-off-by: Gong Cheng <chengg11@yahoo.com>
SVN-Revision: 46652
With this change we let user know 5 seconds have passed and reset button
can be released (to trigger factory reset)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46650
fix generating syscall-names.h
Sometimes the syscall number is not defined with a number but with an
offset to an other syscall and then make_syscall_h.sh created some
broken header file.
For example the bit/syscall.h from musl for i386 has this:
#define __NR_timer_create 259
#define __NR_timer_settime (__NR_timer_create+1)
With this patch the resulting array looks like this:
[259] = "timer_create",
[(__NR_timer_create+1)] = "timer_settime",
This closes#20195.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46612
Add /etc/samba/smbpasswd to list of samba conffiles
thus preserving samba passwords across sysupgrade
by default.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
SVN-Revision: 46606
Install uboot files to KERNEL_BUILD_DIR instead of BIN_DIR to fix
ImageBuilder. Similar fixes are necessary for many (all?) other uboot
targets.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46605
Fixes a 100% cpu usage issue if using dhcp-script.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46550
Better synchronize RA & DHCPv6 events
Accumulate some events to avoid flooding
Restart softwires for address and prefix changes
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46518
of_get_gpio_flags() could return an error like EPROBE_DEFER which was
not handled before. This patch takes the code from gpio_keys_polled.c
for error handling and also improves some other unrelated small parts.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46502
This was deactivated in r21954 because it depended on kernel 2.4, but
this module also compiles with kernel 3.18.
This closes#20199.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46495
An #ifdef for the kernel version was missing around the header of
debugfs_create_devm_seqfile() and the LINUX_BACKPORT() was also not
done.
This closes#20181
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46492
Split the opkg.conf into three files, to make it easier to support custom
feeds and configs:
* /etc/opkg.conf -> base opkg configuration
* /etc/opkg/distfeeds.conf -> default Openwrt package feeds
* /etc/opkg/customfeeds.conf -> custom package feeds
Of these three, only the base opkg.conf and the customfeeds.conf is marked
as to be kept, so that the distfeeds.conf from the image is always used.
To ease migration, a script is added that moves any feeds from /etc/opkg.conf
to /etc/opkg/customfeeds.conf on first boot.
Also ensure that any keys used for verification are also kept in upgrade.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46491
Ath debug mode applies to ath10k as well as ath9k.
Update Makefile help text to clarify.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
SVN-Revision: 46468
We need a+x rights on the path to the root of the jails
so we can use users other than root (like nobody)
This partly fixes jailed dnsmasq
Signed-off-by: Etienne CHAMPETIER <champetier.etienne@gmail.com>
SVN-Revision: 46466
request_mem_region returns NULL when requesting the region failed, and
a valid pointer when it was successful. Currently the condition is
inverted.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46452
The HOST_*FLAGS are for compiling programs which will run on the machine that is
running the build. Setting these flags is frequently required for unusual
cross-compiles.
Signed-off-by: Lawrence D'Anna <larry@elder-gods.org>
SVN-Revision: 46422
otherwise it's not picked up by toolchain:
staging_dir/toolchain-mipsel_24kec+dsp_gcc-4.8-linaro_musl-1.1.10/lib/gcc/mipsel-openwrt-linux-musl/4.8.3/../../../../mipsel-openwrt-linux-musl/bin/ld: cannot find -lsw
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 46406
kmod-at86rf230 select REGMAP_SPI since 3.17, so add a dependency to
kmod-regmap.
Fixes the following error:
Package kmod-at86rf230 is missing dependencies for the following libraries:
regmap-core.ko
regmap-spi.ko
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46387
Also drop the configure (not .ac) patch part as autoreconf will
overwrite it anyway with a newly generated version.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 46385
This update adds a couple of file plugin enhancements, such as base64 support
and setting mode when files are written.
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 46384
Add 802.11r client support to wpa_supplicant. It's only enabled in
wpa_supplicant-full. hostapd gained 802.11r support in commit r45051.
Tested on a TP-Link TL-WR710N sta psk client with two 802.11r enabled
openwrt accesspoints (TP-Link TL-WDR3600).
Signed-off-by: Stefan Hellermann <stefan@the2masters.de>
SVN-Revision: 46377
This controls the old Broadcom switch driver which was removed over a
year ago, since then this is useless. Use swconfig instead it works
with more (Broadcom) switches.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46373
caddr_t is not defined everywhere any more, cast it the the real
pointer type of ifr_data.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46371
To improve reproducibility, prevent the inclusion of timestamps
in the gzip header.
Signed-off-by: Reiner Herrmann <reiner@reiner-h.de>
SVN-Revision: 46361
odhcpd now sends unsolicited RAs also via unicast to known link-local
neighbors. This is an attempt to work-around common smartphone issues
https://code.google.com/p/android/issues/detail?id=32662
Also NDP-relay should now work more reliably now
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 46357
Added option for old firmware version (10.1 API v2). It seems that recent
firmware versions are constantly crashing (at least on a QCA9880-BR4A-R) and
this provides the option to select an older version instead.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
SVN-Revision: 46340
This updates valgrind to version 3.10.1 and make configure work with
kernel version > 4.0. This patch was taken from upstream valgrind.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46302
The musl build "fix" introduced in r45108 removed all netinet/ether.h
includes, which made the prototypes of ether_aton and ether_ntoa
unavailable. As a result, the compiler assumed they return int instead
of a pointer. This currupted the pointer on 64bit targets, causing ebtables
to segfault in commands containing MAC addresses.
Since r46161 made it possible to include both the kernel and the libc
if_ether.h as long as the libc version is included first, this patch
changes the fix to remove the linux/if_ether.h from the ebtables source
(so the fixed version from the kernel is used) and ensures netinet/ether.h
is included early.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46292
During certificate verification, OpenSSL (starting from version 1.0.1n and
1.0.2b) will attempt to find an alternative certificate chain if the first
attempt to build such a chain fails. An error in the implementation of this
logic can mean that an attacker could cause certain checks on untrusted
certificates to be bypassed, such as the CA flag, enabling them to use a valid
leaf certificate to act as a CA and "issue" an invalid certificate.
This issue will impact any application that verifies certificates including
SSL/TLS/DTLS clients and SSL/TLS/DTLS servers using client authentication.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 46285
Make wpan depend on not kernel 3.18 so it will get activated on all
other kernel versions like 4.0 and 4.1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46276
Internal GPIO pins are used for PoE passthrough setups in multi-port
routers. This patch implemnets control over this hardware feature for
Ubiquiti Nanostations and TP-Link CPE510.
Signed-off-by: Lars Kruse <lists@sumpfralle.de>
SVN-Revision: 46271
This reverts commit r45579.
With the latest change r46251 ("nvram: fix "Segmentation fault" caused
by setting memory out of buffer") nvram utility shouldn't crash anymore.
It was tested on 3 brcm47xx devices:
1) Unknown with 0x10000 NVRAM size (0x8000 offset)
2) Linksys E1000 V2.1 with 0x10000 (0x8000 offset)
3) Linksys WRT300N V1 with 0x10000 (0x8000 offset)
And 3 bcm53xx devices:
1) Buffalo WZR-600DHP2 with 0x160000 NVRAM size
2) Buffalo WZR-1750DHP with 0x10000 NVRAM size
3) Netgear R6250 V1 with 0x180000 NVRAM size
(all using 0 offset)
This is an important change as it allows reading whole NVRAM. This may
critical when reading some basic configuration (e.g. switch ports).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46253
Some MTD partitions with NVRAM have content starting in the middle. In
such case offset is set and nvram_header returns pointer to the middle.
It means we have to respect offset when calculating remaining space.
By the way use real MTD partition size (nvram_part_size variable) as we
may want to bump NVRAM_SPACE in the (very near) future.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46251
Ath10k has now a proper method of providing calibration data via
the kernel firmware API. This patch can be dropped as all boards
now use the proper method.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46245
This changes makes it possible to store custom settings
in individual files inside the directory /etc/sysctl.d/.
Signed-off-by: Stefan Tomanek <stefan.tomanek+openwrt@wertarbyte.de>
SVN-Revision: 46239
When enabled the dnsmasq DHCP server allocates the IP addresses sequentially
starting from the lowest available IP address.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 46211
reorder some parts of the patch to remove the declaration-after-
statement warning.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46205
Current firmware should work for station mode as well, and the older
firmware will usually behave worse and become unsupported over time.
Also, the MAC address handling on ar71xx is only implemented on one
firmware version.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46197
This firmware adds support for management frames over normal
packet transport interface instead of over the WMI management
interface.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46195
sd_mod depends on scsi_mod, but due to it being an AutoLoad and not
AutoProbe module, it was not loading when installing the package,
causing unknown symbol errors for sd_mod and anything depending on it.
Closes#14927, #18293, #19351.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46176
We were not copying the additional files needed to get USB to work on
the AT91 platforms, make sure we do this.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 46172
This brings curl to version 7.43.0 and contains fixes for the following
security vulnerabilities:
CVE-2015-3236: lingering HTTP credentials in connection re-use
http://curl.haxx.se/docs/adv_20150617A.html
CVE-2015-3237: SMB send off unrelated memory contents
http://curl.haxx.se/docs/adv_20150617B.html
The 100-check_long_long patch is not needed any more, because the
upstream autoconf script already checks for long long when cyassl is
selected.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46169
This patch introduces a new build error into coova-chilli, but
coova-chilli already fails to build even without it anyway. CyaSSL is
now called wolfSSL, and all the API's have been renamed, and
backward-compatibility headers added.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46167
The g++-uc wrapper hardcodes $(STAGING_DIR) and $(TOOLCHAIN_DIR) paths which
will not work outside of the original build environment.
Replace the hardcoded staging_dir occurences with paths relative to the
$STAGING_DIR environment variable to make the g++-uc* wrappers usable in an
SDK environment.
Fixes the libdb47 build failure reported at
https://lists.openwrt.org/pipermail/openwrt-devel/2015-April/032455.html
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 46162
A long time ago, ath9k had issues during reset where the DMA engine
would stay active and could potentially corrupt memory.
To debug those issues, the driver would print warnings whenever they
occur.
Nowadays, these issues are gone and the primary cause of these messages
is if the MAC is stuck during reset or busy processing a long
transmission. This is fairly harmless, yet these messages continue to
worry users.
To reduce the number of bogus bug reports, turn these messages into
debug messages and count their occurence in the "reset" debugfs file.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46158
A duplicate include guard prevents inclusion of barrier.h in UML build and this prevents mac80211 from building.
This patch re-enables mac80211 hwsim and renames the include guard.
See https://lists.openwrt.org/pipermail/openwrt-devel/2015-June/033614.html for details.
Signed-off-by: Martin Tippmann <martin.tippmann@gmail.com>
Signed-off-by: Nicolas Thill <nico@openwrt.org>
SVN-Revision: 46133
Avoid redefining `realpath` to fix the following error:
.../include/fortify/stdlib.h:36:13: error: 'realpath' undeclared here (not in a function)
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 46127
Invert the `__GLIBC__` guards into `!__UCLIBC__` ones to avoid
invalid references to `_llseek` on musl.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 46125
- include upstream fixes for musl compatibility
Include <sys/stat.h> for S_I* macros
d34e00b293942b1012ddc49ed3ab379a32337611
Include <linux/ioctl.h> for _IOC_* macros
3460dc486d333231998de0f19918204aacee9ae3
strace 4.8 is broken with musl on some arch
(arm: omap,oxnas according to buildbot)
compile tested only
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 46124
Boot tested: http://pastebin.com/L6aAb9xj
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo:
update to 4.1 final
add patches added since submission
delete patches applied in later rcs
restore commit messages in 220-gc-sections and 304-mips_disable_fpu
fix 050-backport_netfilter_rtcache to match new API
update inlined dma ops with upstream changes
add missing config symbols
enabled CONFIG_MULTIUSER
update kmod defintions for 4.1
]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46112
Without this the condition
if __BYTE_ORDER == __BIG_ENDIAN
was always true.
Thanks Szabolcs.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46105
There are two important patches in this patchset: updating read pointer
quicker & rework of .get_station().
There are few more upstream patches that are p2p-related and weren't
backported in this commit.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46084
So far we got only one generic function accessing this table, but
implementing optimizations will require calculating crc32 in other code
parts as well.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46077
This fixes some build problems with musl. The binary only program
nas.exe wants to link against __assert, which is copied from uClibc.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46021
On bcm53xx we still need usb-ohci to support USB 1.1 devices and it
obviously needs bcma-hcd.ko that will init controller and register
platform device.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45994
This one cannot possibly work, as it depends on cfg80211, which is built
out of tree.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45985
Besides source.tgz, 001-elfutils-portability.patch (provided by upstream
project) where updated.
Other patches where updated to fix hulk warnings and minor conflicts.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
SVN-Revision: 45984
elfutils is required by perf. So we'll move this package from
packages.git and make it part of the core distribution.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45969
bzip2 is required by elfutils, itself required by perf. So we'll move
this package from packages.git and make it part of the core
distribution.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45968
argp-standalone is required by elfutils, itself required by perf. So
we'll move this package from packages.git and make it part of the core
distribution.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45967
This is for security precautions. As persist_tun and persist_key are
already there, this should not cause compatibility issue.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 45961
- fix iconv detection because it adds host paths
- disable python detection (host python-config is found)
iconv issue is reported by buildbot config.log + replicated locally
see config.log in logs.tar.gz
python issue observed locally on Arch Linux
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45953
