Open-Mesh OM5P-AN use a AT8035 (F1E) behind one of the ethernet ports. This PHY
requires special flags to work correctly. Otherwise massive packet loss happens
with active POE or when switching the link speed from gigabit ethernet to fast
ethernet. The generic PHY doesn't have support to change these settings.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 45439
The OM5P-AN boards are suffering from ethernet packet loss when booting with
some active POE setups or when switching to Fast Ethernet when previously
booted with Gigabit ethernet attached.
The cause of the problem is that the AR8035 PHYs requires special register
settings to work reliably on these boards. Enable the RGMII TX, RX delays and
disable SmartEE functionality of the AR8035 PHYs. Also enable the RXD and RDV
delay in the ETH_CFG register to fix the issue.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 45438
it has been non-functional for years and caused numerous memleaks and
crashes for people that tried to enable it.
it has no maintained upstream source, and it does not look like it's
going to be fixed any time soon
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45423
It seems to have few ports connected to CPU (only for CPU sending data?)
as part of "SMP dual core 3 GMAC setup" feature.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45403
On BCM5301X there are two different cases to handle: CPU port 8 vs. any
other one. Support for CPU port 8 was already partially implemented but
it lacked setting some extra bit for 2G speed. It also will need to be
extended to implement "SMP dual core 3 GMAC setup". That's the reason
for handling it in separated code block.
This patch also adds overriding CPU port state for port other than 8. It
requires using recently defined GMII_PORT registers.
It was tested for regressions on BCM53011 revs 2 & 3. It was also
confirmed to fix switch on some internal Broadcom board.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45402
In most cases it allows reverting back to the vendor firmware (as they
usually don't use UBI). If users wants to do that we can't do anything
anyway. Erease counters will be just lost. The only thing we do is warn:
"Flashing firmware without UBI for rootfs. All erase counters will be
lost."
It still requires forcing sysupgrade.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45392
We can now detect that provided firmware contains kernel and UBI image
partitions. Flashing it in a sane way (keeping erase counters) still
needs to be implemented.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45391
With previous version of patch info about need of erasing blocks was
stored once per boot. It was breaking in following scenario:
1) First boot after installation (erasing blocks after 0xdeadc0de)
2) Doing sysupgrade (with ubidetach & ubiformat)
3) Attaching UBI again (it caused all blocks to be erased)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45387
It currently does not seem to make a difference anymore, except by
increasing compressed kernel image size
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45385
* properly enclose macro arguments in paranthesis on use
* remove trailing white space
* convert C99 // comments
* add missing blank lines after declaration
* remove braces from single statement blocks
* split lines > 80 chars (except for one)
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45356
Having CONFIG_XZ_DEC_ARMTHUMB enabled breaks squashfs when ARM BCJ
filter was used to create the filesystem (and that's what we do on
all ARM targets). Thus unset CONFIG_XZ_DEC_ARMTHUMB to fix
squashfs on sunxi.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 45347
kmod-usb-phy-qcom-dwc3 is required to get USB working on ipq806x. It was
missed in previous commit so let's enable it automatically.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45345
MicroWRT is an wireless router with 2 USB,1 ethernet port. It
has a 16M flash and 64M DDR2 RAM. You can use most interface, such as
i2c, SPI, i2s and PCIe. Besides that there are three expansion borad to
combine with the core board. The detailed information, please refer to
https://www.microduino.cc/wiki/index.php?title=Main_Page
This patch adds support for it.
Because there is only one port,so disabled VLAN and use eth0 as lan
port. and only a power LED control by power pin.
Signed-off-by: 盛凯 <shengkai81@gmail.com>
SVN-Revision: 45331
None of the LEDs are enabled by default on the Hornet-UB X2 board
(the 16/64MB version of the Hornet-UB), because it uses a different
board-name ("hornet-ub-x2"); but hornet-ub and hornet-ub-x2 boards
are equivalent WRT their LEDs.
SIgned-off-by: Joshua Judson Rosen <jrosen@harvestai.com>
SVN-Revision: 45328
On newer Mikrotik boards, the radio calibration data
is stored differently and uses LZO compression instead
of RLE.
Update the RouterBOOT helper code to support the new
format.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 45297
First of all this patch was affecting other devices, not just Netgear
WNR834B. E.g. Linksys WRT300N v1 also has boardtype 0x0472.
This was breaking PCI on WRT300N, ssb couldn't detect core working in
hostmode (due to mips_busprobe32 failing).
Secondly this patch should not be needed for years now. From the analyze
of #8861 it seems it was needed just to make devices at slots other than
0 discoverable. Setting cardbus to 0 was simply making ssb allow access
to PCI config for devices other than bridge.
With the upstream commit a6c8462 (ssb: fix cardbus slot in hostmode) we
allow accessing device at slot 1 which should be enough for CardBus.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45293
SCHED_AUTOGROUP was turned on by default which forces the use of
CGROUPS, conflicting with the options we offer from menuconfig, remove
that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 45275
