Commit graph

15188 commits

Author SHA1 Message Date
Petr Štetiar
60dd181a76 base-files: diag.sh: Make it more generic towards DTS so it could be reused
I wanted to add status LEDs support to my imx6 based board and have
found out, that I could use diag.sh script found in ramips platform,
which seems to be also shared in a few other platforms:

 4801276bc2078c5bcf03003c831e3b0a target/linux/ramips/base-files/etc/diag.sh
 4801276bc2078c5bcf03003c831e3b0a target/linux/ipq40xx/base-files/etc/diag.sh
 4801276bc2078c5bcf03003c831e3b0a target/linux/ath79/base-files/etc/diag.sh

So I've extended the base diag.sh in a way, that if it detects any of
the DTS LED aliases, then it would use the generic DTS set_led_state
code.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-06 08:42:40 +01:00
Rosen Penev
26dcaf58ee comgt: Fix 3g.sh permissions
3g.sh needs to be executable. 600 is not correct for that.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-12-06 08:42:39 +01:00
Michael Heimpold
d6ac8ca76c base-files: fix several bashisms
For equality test a simple = is sufficient, the == is
usually disregarded as bashism.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2018-12-05 22:16:52 +01:00
Steven Lin
2b4ac79a79 ipq40xx: add support for EnGenius EAP1300
SOC:    IPQ4018 / QCA Dakota
CPU:    Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:   256 MiB
NOR:    32 MiB
ETH:    Qualcomm Atheros QCA8072
WLAN1:  Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:  Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:  RESET Button
LEDS:   Power, LAN, MESH, WLAN 2.4GHz, WLAN 5GHz

1. Load Ramdisk via U-Boot

To set up the flash memory environment, do the following:
a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters:
   * 115200bps
   * 8N1
b. Confirm that the PC is connected to the board using one of the Ethernet ports. Set a static ip 192.168.99.8 for Ethernet that connects to board. The PC must have a TFTP server launched and listening on the interface to which the board is connected. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown.

U-BOOT> set serverip 192.168.99.8 && set ipaddr 192.168.99.9 && tftpboot 0x84000000 openwrt.itb && bootm

2. Load image via GUI

a. Upgrade EAP1300 to FW v3.5.3.2
In the GUI, System Manager > Firmware > Firmware Upgrade, to do upgrade.
b. Transfer to OpenWrt from EnGenius.
In Firmware Upgrade page, to upgrade yours openwrt-ipq40xx-engenius_eap1300-squashfs-sysupgrade.bin.

3. Revert to EnGenius EAP1300
To flash openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin by using sysupgrade command and "DO NOT" keep configuration.
$ sysupgrade –n openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin

Signed-off-by: Steven Lin <steven.lin@senao.com>
2018-12-05 09:40:32 +01:00
Stijn Tintel
e261c8b764 brcm2708-gpu-fw: add fw required for camera module
To be able to use the camera module, start_x=1 has to be set in
config.txt. This will cause the bootloader to load the GPU firmware that
contain the extra video codecs. Install these firmware files.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-05 00:39:53 +02:00
Stijn Tintel
42ca32ad2f brcm2708-gpu-fw: update to git HEAD
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-05 00:09:14 +02:00
Stijn Tintel
f208f77811 mac80211: fix brcmfmac on brcm2708
An upstream change broke brcmfmac when loaded with modparam roamoff=1.
As we are carrying a patch that enables roamoff by default on the
brcm2708 target to improve stability, wireless is currently broken
there. Add a patch to fix brcmfmac with roamoff=1.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-04 22:45:08 +02:00
Felix Fietkau
4fd7882822 mt76: update to the latest version
5a5b396 mt76: throttle transmission of buffered multicast packets
8084323 mt7603: implement code for adjusting energy detect CCA thresholds
8929a6e mt7603: increase MCU timeout
f2ba65f mt7603: update firmware to 20161027164355
0ad998b mt7603: increase aggregation limits (based on vendor driver changes)
da00af0 mt7603: clear bit 18 in MT_SEC_SCR to fix ICV error

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-12-04 12:28:56 +01:00
Florian Eckert
675eb747aa openvpn: add list element parsing
For the parameters tls-cipher and ncp-ciphers more than one option can
be used in the OpenVPN configuration, separated by a colon, which should
be implemented as a list in order to configure it more clearly. By
adding the new OPENVPN_LIST option to the openvpn.options file with the
tls-cipher and ncp-cipher parameters, uci can now add this option as a
"list" and the init script will generate the appropriate OpenVPN
configuration from it.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2018-12-03 09:54:03 +01:00
Eneas U de Queiroz
3fb45576ac cryptodev-linux: move from packages feed
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.

To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
This is actually a build dependency for /dev/crypto support in openssl.
Since it is a kernel module, it belongs here anyway.

- Removed Nikos Mavrogiannopoulos as maintainer.
- Streamlined make flags

Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
2018-12-03 07:50:24 +01:00
Jo-Philipp Wich
9808bd2799 Revert "base-files: fwtool: Fix wrong checksum on combined-image with metadata"
This reverts commit 41770add03.

The fwtool_check_image() procedure is used by `sysupgrade --test` which must
not alter the image under test in any way.

Currently, when the LuCI ui or any other sysupgrade wrapper first invokes
sysupgrade --test to verify the compatibility of the image and then calculates
the sha256sum over it, the resulting checksum will differ from the original
image since the test invocation will implicitely strip the metadata trailer.

To properly fix the underlying issue, the combined image checksumming code
must be modified to skip the metadata trailer.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-12-02 16:05:44 +01:00
Hans Dedecker
493c1d1766 odhcpd: update to latest git HEAD
d404c7e netlink: fix triggering of NETEV_ADDR6LIST_CHANGE event
ae6cf80 config: correctly break string for prefix filter

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-11-29 21:46:12 +01:00
Tony Ambardar
8806da86f5 base-files: fix prerm return value, align with postinst code
The return value of a package prerm script is discarded and not returned
correctly by default_prerm(). This allows other operations like service
shutdown to "leak" their return value, prompting workarounds like commit
48cfc826 which do not address the root cause.

Preserve a package prerm script return value for use by default_prerm(),
sharing the corresponding code from default_postinst() for consistency.
Also use consistent code for handling of /etc/init.d/ scripts.

Run Tested on: LEDE 17.01.4 running ar71xx.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2018-11-29 11:52:56 +01:00
Felix Fietkau
5ffacceb7b mac80211: fix reordering of buffered broadcast packets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-28 23:23:38 +01:00
Felix Fietkau
87b874d4d6 mt76: update to the latest version
5fb60a7 mt7603: fix aggregation size handling
31cd20e mt7603: issue PSE reset on stuck beacon
4063ae1 mt7603: check for PSE hang / stuck beacon first
00e03b9 mt7603: fix MT_WF_PHY_CR_RXTD_BASE definition
c3efb5d mt7603: add support for detecting MT7688 and single stream devices
2a136cb mt7603: fix TKIP key setup
cd456ca mt7603: disable broken support for WEP hardware encryption
3ecb7f8 mt7603: fix hardware queue assignment
6ac9653 mt7603: fix CAB queue limits
d22feb0 mt7603: move cab queue enabling to pre-tbtt tasklet
44bb372 mt7603: fix CAB queue flush mask

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-28 23:23:38 +01:00
Jo-Philipp Wich
3082370551 openvpn: update to 2.4.6
Update the OpenVPN package to version 2.4.6, refresh patches and drop
menuconfig options which are not supported upstream anymore.

Also fix the x509-alt-username configure flag - it is not supported
by mbedtls and was syntactically wrong in the Makefile - and the
port-share option which has been present in menuconfig but not been
used in the Makefile.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-11-28 22:10:19 +01:00
Jo-Philipp Wich
56378bc12d uhttpd: update to latest Git head
cdfc902 cgi: escape url in 403 error output
0bba1ce uhttpd: fix building without TLS and Lua support
2ed3341 help: document -A option
fa5fd45 file: fix CPP syntax error
77b774b build: avoid redefining _DEFAULT_SOURCE

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-11-28 12:55:50 +01:00
John Crispin
231d9d5327 Revert "intel-microcode: create early load microcode image"
This reverts commit 022ffb56b2.

Signed-off-by: John Crispin <john@phrozen.org>
2018-11-27 18:58:37 +01:00
John Crispin
30f30d3e11 Revert "amd64-microcode: create early load microcode image"
This reverts commit 975019b3a7.

Signed-off-by: John Crispin <john@phrozen.org>
2018-11-27 18:58:33 +01:00
Hans Dedecker
533f7673ae netifd: update to latest git HEAD
dfa4ede interface: fix return code of __interface_add()
a82a8f6 netifd: fix resource leak on error in netifd_add_dynamic()
fa2403d config: fix resource leaks on error in config_parse_interface()
85de9de interface: fix memory leak on error in __interface_add()

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-11-26 15:33:45 +01:00
Steven Honson
a73283dc10 kernel: nf-nathelper-extra depends on ipt-raw
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.

To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
As automatic helper assignment is disabled in recent Linux kernels,
explicit rules must be added to the raw table for each helper.

While commit f50a524 in the firewall3 project added a set of default
rules and other additional related functionality, both this and the
alternative manual methods of defining these rules require kmod-ipt-raw.

Signed-off-by: Steven Honson <steven@honson.id.au>
2018-11-26 12:05:47 +01:00
Christian Lamparter
d82d84694e apm821xx: add support for the Netgear WNDAP620 and WNDAP660
This patch adds support for the Netgear WNDAP620 and WNDAP660,
they are similar devices, but due to the LAN LED configuration,
the switch setup and WIFI configuration each gets a different
device target.

Hardware Highlights WNDAP620:
CPU: AMCC PowerPC APM82181 at 1000 MHz
DRAM:  128 MB, 2 x 64 MiB DDR2 Hynix H5PS5162GF
CPU: AMCC PowerPC APM82181 at 1000 MHz
FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A
Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY - Only 1 GBit Port (POE)
Wifi: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Serial: console port with RJ45 Interface (9600-N-8-1)
LEDS: Power, LAN-Activity, dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs
Button: Soft Reset Button
Antennae: 3 internal dual-band antennae + 3 x RSMA for external antennaes

Hardware Highlights WNDAP660:
CPU: AMCC PowerPC APM82181 at 1000 MHz + 2 Heatsinks
DRAM:  256 MB, 2 x 128 MiB DDR2
FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A
Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY (POE)
Wifi1: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Wifi2: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Serial: console port with RJ45 Interface (9600-N-8-1)
LEDS: Power, LAN-Activity, 2x dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs
Button: Soft Reset Button
Antennae: 6 internal dual-band antennae + 3 x RSMA for external antennaes

Flashing requirements:

 - needs a tftp server at 192.168.1.10/serverip.
 - special 8P8C(aka RJ45)<->D-SUB9 Console Cable
   ("Cisco Console Cable"). Note: Both WNDAP6x0 have
   a MAX3232 transceivers, hence no need for any separate
   CMOS/TTL level shifters.

External Antenna:
The antennae mux is controlled by GPIO 11 and GPIO14. Valid Configurations:
 = Config# = | = GPIO 11 = | = GPIO 14 = |  ===== Description =====
      1.     |   1 / High  |  0 / Low    | Use the internal antennae (default)
      2.     |   0 / Low   |  1 / High   | Use the external antennae

The external antennaes are only meant for the 2.4 GHz band.

One-way Flashing instructions via u-boot:

 0. connect the serial cable to the RJ45 Console Port
    Note: This requires a poper RS232 and not a TTL/USB adaptor.

 1. power up the AP and interrupt the u-boot process at

    'Hit any key to stop autoboot'

 2. setup serverip and ipaddr env settings
    Enter the following commands into the u-boot shell
    # setenv ipaddr 192.168.1.1
    # setenv serverip 192.168.1.10

 3. download the factory.img image to the AP
    Enter the following commands into the u-boot shell

    # tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-squashfs-factory.img

 4. verfiy image integrity
    Enter the following commands into the u-boot shell

    # crc32 $fileaddr $filesize

    If the calculated crc32 checksum does not match, go back to step 3.

 5. flash the image
    Enter the following commands into the u-boot shell

    # nand erase 0x110000 0x1bd0000
    # nand write ${kernel_addr_r} 0x110000 ${filesize}

 6. setup uboot environment
    Enter the following commands into the u-boot shell

    # setenv bootargs
    # setenv fileaddr
    # setenv filesize
    # setenv addroot 'setenv bootargs ${bootargs} root=/dev/ubiblock0_0'
    # setenv owrt_boot 'nboot ${kernel_addr_r} nand0 0x110000; run addroot; run addtty; bootm ${kernel_addr_r}'
    # setenv bootcmd 'run owrt_boot'
    # saveenv

 7. boot
    # run bootcmd

Booting initramfs instructions via u-boot:

 Follow steps 0 - 2 from above.

 3. boot initramfs
    Enter the following commands into the u-boot shell

    # tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-initramfs-kernel.bin
    # run addtty
    # bootm ${kernel_addr_r}

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-11-26 12:05:46 +01:00
Christian Lamparter
e21a9db47d apm821xx: MX60(W): enable u-boot environment
This patch adds u-boot environment access to the MX60(W) target.
"The environment size is one NAND block (128KiB on Buckminster).
We allocate four NAND blocks to deal with bad blocks which may
exist in the saved  environment"

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-11-26 12:05:46 +01:00
Christian Lamparter
f6968952df apm821xx: MR24: add to uboot-envtools
This patch adds the complicated u-boot
environment access settings for to the
MR24 target.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-11-26 12:05:46 +01:00
Christian Lamparter
6f4f77aa1d apm821xx: add uboot-envtools support
All apm821xx devices use u-boot and most of them have
an accessible u-boot environment. This patch adds the
necessary template file, but does not add the
uboot-envtools package to any of the targets.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-11-26 12:05:46 +01:00
Petr Štetiar
41770add03 base-files: fwtool: Fix wrong checksum on combined-image with metadata
If I create following image:

define Device/engenius-m36
  IMAGE/sysupgrade.bin := combined-image | append-metadata
endef

Sysupgrade then errors out:

  Invalid image. Contents do not match checksum (image:cd285595eaf297370404ae0e2815ec1a calculated:2cf9a2286fb6b01af3ea189128017d44)
  Image check 'platform_check_image' failed.

By removing the metadata from the image I get combined-image checksum
working again and sysupgrade works.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-26 12:05:45 +01:00
Tomasz Maciej Nowak
975019b3a7 amd64-microcode: create early load microcode image
Create initrd image with packed microcode. This'll allow to load it at
early boot stage.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-11-26 12:05:45 +01:00
Tomasz Maciej Nowak
022ffb56b2 intel-microcode: create early load microcode image
Create initrd image with packed microcode. This'll allow to load it at
early boot stage.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-11-26 12:05:44 +01:00
Tomasz Maciej Nowak
ad83fde30d intel-microcode: remove dependency on iucode-tool
It is not necessary to have iucode-tool present on target system to have
functional intel-microcode package. The build time dependency is kept.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-11-26 12:05:44 +01:00
Syrone Wong
0331770299 valgrind: enable LTO and refresh patches
Signed-off-by: Syrone Wong <wong.syrone@gmail.com>
2018-11-26 09:44:42 +01:00
Hans Dedecker
a0d5acfbe2 nghttp2: bump to 1.35.0
e520469b Update manual pages
54067256 Bump up version number to 1.35.0
c4d2eeee Update AUTHORS
f51e696e asio: Add stop() to listen_and_serve doc
a433b132 Merge pull request #1260 from nghttp2/h2load-non-final-response
cf48a56d Merge pull request #1238 from jktjkt/cmake-fix-libevent-detection
6cad1b24 nghttpx: Write mruby send_info early
3c393dca nghttpx: Fix assertion failure on mruby send_info with HTTP/1 frontend
17292445 h2load: Handle HTTP/1 non-final response
f6644a92 make clang-format
48998f72 Merge pull request #1222 from donny-dont/fix/declspec
15ff52f9 Update README
6c03bb14 Upgrade travis toolchain
524b4392 Fix travis build failure
859bf2bc Update manual pages
b5619fb1 h2load: Clarify that time for connect includes TLS handshake
dcbe0c69 nghttpx: Simplify move ctor and operator
2996c284 nghttpx: Cleanup
42e8ceb6 nghttpx: Convert API status code to enum class
1daf9ce8 nghttpx: Convert WorkerEventType to enum class
d68edf56 nghttpx: Convert MemcachedStatusCode to enum class
0c4e9fef nghttpx: Convert memcached op to enum class
571404c6 nghttpx: Convert MemcachedParseState to enum class
4d562b77 nghttpx: Convert LogFragmentType to enum class
e6225871 nghttpx: Convert connection check status to enum class
4bd075de nghttpx: Convert Http2Session state to enum class
b46a3249 nghttpx: Convert FreelistZone to enum class
4bd44b9c nghttpx: Convert dispatch state to enum class
1b42110d nghttpx: Make Downstream state enum class
0735ec55 nghttpx: Convert shrpx_connect_proto to enum class
00554779 nghttpx: Convert DNSResolverStatus to enum class
0963f389 nghttpx: Convert SerialEventType to enum class
1abfa3ca nghttpx: Make TLS handshake state enum class
f2159bc2 nghttpx: Convert UpstreamAltMode to enum class
b0eb68ee nghttpx: Convert shrpx_forwarded_node_type to enum class
e7b7b037 nghttpx: Convert shrpx_cookie_secure to enum class
5e4f434f nghttpx: Convert shrpx_session_affinity to enum class
20ea964f nghttpx: Convert shrpx_proto to enum class
d105619b src: Remove extra braces if possible
ec5729b1 Use std::make_unique
6c919695 Use C++14
46576178 Don't send Transfer-Encoding to pre-HTTP/1.1 clients
5e925f87 Update doc
153531d4 nghttpx: Use the same type as standard stream operator<<
f7287df0 Bump up version number to 1.35.0-DEV

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-11-25 20:22:15 +01:00
Roman Bazalevsky
1f4f9b2116 kernel/modules: TI ADS1015 kernel module support enabled.
Signed-off-by: Roman Bazalevsky <rvb@rvb.name>
2018-11-25 19:26:56 +01:00
Roman Bazalevsky
e26a55e749 kernel/modules: ROHM BH1750 ALS IIO kernel module support enabled.
Signed-off-by: Roman Bazalevsky <rvb@rvb.name>
2018-11-25 19:26:56 +01:00
Kabuli Chana
392eea392c mwlwifi: update to version 10.3.8.0-20181114
compile / test target mvebu / mamba

Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
2018-11-25 19:26:55 +01:00
Petr Štetiar
7c104a8358 base-files: sysupgrade: Allow downloading of firmware images using HTTPS
Currently it's only possible to download images over HTTP.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-25 19:26:50 +01:00
Syrone Wong
09eac6d13f strace: update to 4.25
Signed-off-by: Syrone Wong <wong.syrone@gmail.com>
2018-11-25 19:23:03 +01:00
Jo-Philipp Wich
0bd99db511 uclient: update to latest Git head
3ba74eb uclient-http: properly handle HTTP redirects via proxy connections

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-11-24 20:15:04 +01:00
Hans Dedecker
c19f1a8665 procd: update to latest git HEAD
d667354 early: set /tmp permissions explicitly

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-11-23 15:27:35 +01:00
Jo-Philipp Wich
952b11766c rpcd: update to latest Git head
c79ef22 main: fix logic bug when not specifying a timeout option

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-11-22 16:30:38 +01:00
Jo-Philipp Wich
4105555115 rpcd: update to latest Git head
2cc4b99 file: use global exec timeout instead of own hardcoded limit
ecd1660 exec: increase maximum execution time to 120s

Also expose the socket and timeout options in /etc/config/rpcd for
easier use.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-11-22 14:43:36 +01:00
Linus Kardell
2ac1a57677 base-files: fix unkillable processes after restart
When restart is run on an init script, the script traps SIGTERM. This is
done as a workaround for scripts named the same name as the program they
start. In that case, the init script process will have the same name as
the program process, and so when the init script runs killall, it will
kill itself. So SIGTERM is trapped to make the init script unkillable.

However, the trap is retained when the init script runs start, and thus
processes started by restart will not respond to SIGTERM, and will thus
be unkillable unless you use SIGKILL. This fixes that by removing the
trap before running start.

Signed-off-by: Linus Kardell <linus@telliq.com>
2018-11-22 13:15:10 +01:00
Felix Fietkau
0191a06985 mt76: update to the latest version
4734108 mt7603: use mt7603_wtbl_clear on station removal
9428e34 mt7603: fix watchdog reset sequence
b3f82a3 mt7603: report PSE reset failures via debugfs
a301dec mt7603: add back PSE client reset code
94cebfc mt7603: fix handling lost interrupt events during watchdog reset
b38fe7d mt7603: only issue PSE reset on PSE stuck
da666a7 mt7603: issue PSE reset if firmware debug register indicates stuck queues

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-21 15:15:05 +01:00
Felix Fietkau
8184bdddc4 mt76: update to the latest version
471d397 mt7603: fix priority for buffered multicast packets
3873e82 mt7603: fix MT_BMAP_0/MT_GROUP_THD_0 register initializion for mt7628
749d5c3 mt7603: fix reserved page handling for mt7628
d22799b mt7603: reduce reserved pages for beacons
42c5281 mt7603: fix maximum frame size in scheduler init
fa7335b mt76: fix potential NULL pointer dereference in mt76_stop_tx_queues
84aa12a mt76: fix potential null pointer deref in mt76_sta_add
7c4c33c mt7603: skip efuse tx power data for mt7628
ca2c875 mt7603: add support for accessing remapped registers via ops
b44d793 mt7603: clear PSE redirections before MCU init
82363ab mt7603: move tx status to rx queue 0
c09e8a4 mt7603: fix buffering of tx packets for powersave clients

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-20 16:56:11 +01:00
Jason A. Donenfeld
48d8d46d33 wireguard: bump to 0.0.20181119
* chacha20,poly1305: fix up for win64
* poly1305: only export neon symbols when in use
* poly1305: cleanup leftover debugging changes
* crypto: resolve target prefix on buggy kernels
* chacha20,poly1305: don't do compiler testing in generator and remove xor helper
* crypto: better path resolution and more specific generated .S
* poly1305: make frame pointers for auxiliary calls
* chacha20,poly1305: do not use xlate

This should fix up the various build errors, warnings, and insertion errors
introduced by the previous snapshot, where we added some significant
refactoring. In short, we're trying to port to using Andy Polyakov's original
perlasm files, and this means quite a lot of work to re-do that had stableized
in our old .S.

Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
2018-11-19 22:15:02 +01:00
Hans Dedecker
8e409f476b netifd: update to latest git HEAD
4b83102 treewide: switch to C-code style comments
70506bf treewide: make some functions static
d9872db interface: fix removal of dynamic interfaces
2f7ef7d interface: rework code to get rid of interface_set_dynamic

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-11-19 10:15:26 +01:00
Felix Fietkau
251c350727 mt76: update to the latest version
96b3b3d mt76x2u: main: fix typo setting sta_state mac80211 callback

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-16 13:43:33 +01:00
Felix Fietkau
86fc443f8b mt76: update to the latest version
009ab91 mt76: clean up more unused EXPORT_SYMBOLs
963768d mt76x02: fix regression in tx station race condition fix
d7788cc mt76: mt76x02: make group_wcid the first member in struct mt76x02_vif
e65ad4c mt7603: make group_wcid the first member in struct mt7603_vif
7b1373e mt76: mt76x02: remove mt76x02_txq_init
a97127b mt76: replace sta_add/remove ops with common sta_state function
13f1e82 mt7603: clear wtbl entry for removed stations
90e2c1b mt7603: add mt7603_wtbl_set_skip_tx, change mt7603_wtbl_set_ps users
41931e4 mt7603: toggle skip_tx on station add/remove
d0fdf01 mt7603: avoid unnecessary wtbl writes for ps-filter

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-16 12:44:01 +01:00
Jason A. Donenfeld
bf52c968e8 wireguard: bump to 0.0.20181115
* Zinc no longer ships generated assembly code. Rather, we now
  bundle in the original perlasm generator for it. The primary purpose
  of this snapshot is to get testing of this.
* Clarify the peer removal logic and make lifetimes more precise.
* Use READ_ONCE for is_valid and is_dead.
* No need to use atomic when the recounter is mutex protected.
* Fix up macros and annotations in allowedips.
* Increment drop counter when staged packets are dropped.
* Use static constants instead of enums for 64-bit values in selftest.
* Mark large constants as ULL in poly1305-donna64.
* Fix sparse warnings in allowedips debugging code.
* Do not use wg_peer_get_maybe_zero in timer callbacks, since we now can
  carefully control the lifetime of these functions and ensure they never
  execute after dropping the last reference.
* Cleanup hashing in ratelimiter.
* Do not guard timer removals, since del_timer is always okay.
* We now check for PM_AUTOSLEEP, which makes the clear*on-suspend decision a
  bit more general.
* Set csum_level to ~0, since the poly1305 authenticator certainly means
  that no data was modified in transit.
* Use CHECKSUM_PARTIAL check for skb_checksum_help instead of
  skb_checksum_setup check.
* wg.8: specify that wg(8) shows runtime info too
* wg.8: AllowedIPs isn't actually required
* keygen-html: add missing glue macro
* wg-quick: android: do not choke on empty allowed-ips

Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
2018-11-16 09:23:02 +01:00
Daniel Engberg
59ff8687c7 util-linux: Update to 2.33
Update util-linux to 2.33
Refresh patch

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2018-11-15 21:19:37 +01:00
Kevin Darbyshire-Bryant
3a6bddd7f7 hostapd: add utf8_ssid flag & enable as default
SSIDs may contain UTF8 characters but ideally hostapd should be told
this is the case so it can advertise the fact. Default enable this
option.

add uci option utf8_ssid '0'/'1' for disable/enable e.g.

config wifi-iface
	option utf8_ssid '0'

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-11-14 17:41:18 +00:00