Commit graph

140 commits

Author SHA1 Message Date
John Crispin
8b38a9450b ramips: Add support for Phicomm PSG1208
This patch adds support for Phicomm PSG1208.This is a router with MT7620A SoC with 8M flash and 64M ram.
The WPS led is uesd as status_led because the power light can't be controlled with GPIO.
It seems that the 5g wifi led is connected to MT7612E and it can't be controlled with GPIO too.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>

SVN-Revision: 48721
2016-02-15 18:45:22 +00:00
John Crispin
9f9682a79b ramips: Add support for Netgear EX2700
This patch adds support for the Netgear EX2700 and builds an approriate
sysupgrade image.

What's missing is the option to build a factory image flashable via the
router's stock web interface, but this approach is hindered by the fact
that u-boot operforms an additional integrity check, which expects a
uImage header in the last 64 bytes of the "kernel" partition, which
the bootloader expects to be 960k, a size exceeded by the standard
OpenWrt kernel.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>

SVN-Revision: 48698
2016-02-12 08:29:33 +00:00
John Crispin
de7dce21a3 ralink: add WRTnode2 platform and led support
Signed-off-by: xzmu <xzmu@wrtnode.com>

SVN-Revision: 48049
2016-01-01 21:19:50 +00:00
John Crispin
4e31b2e869 ramips: add support for Ubiquiti EdgeRouter X (UBNT-ERX)
This router is based on MT7621 SoC, no wifi, no usb, nand.

Works:
* Boots.
* Ethernet.
* Switch.
* Button (reset).
* Flashing OpenWrt from stock firmware.
* Upgrading OpenWrt.

Doesn't work:
* No GPIO leds. All leds are controlled by switch,
  but stock firmware was able to control them.
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
  nand/spi drivers do not support pin sharing,
  so it is not accessable and disabled. Stock
  firmware could read it and it was empty.
* PoE out.

Router has serial pins populated. If looking at the top
of the router, then counting from Eth sockets pins go as:
'GND, RX, TX, GND'. 3.3v, 57600.

U-boot bootloader supports tftpboot, controlled from serial.
This router has two kernel partitions: 'live' and 'backup'.
They are swapped during flashing (on both stock and OpenWrt).
Active partition is controlled by a flag in a factory partition.
U-boot has custom command to switch active kernel partition.
Kernel partitions are 'bare flash' 3MB. Stock bootloader has
no UBI support. Stock rootfs is UBIFS.

Flashing procedure.
Stock firmware uses custom kernel patch to mount squashfs
from a file that is located on UBIFS volume. This makes wiping
out this volume from within stock firmware difficult.
Instead this patch builds image that is flashable by stock firmware
and contains initrams image (with minimal set of packages
to fit into kernel partition). Once this is flashed one can reboot
into initramfs OpenWrt and use sysupgrade to flash OpenWrt including
rootfs into nand.
Note: factory image is only built if initramfs image is enabled.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47881
2015-12-12 07:38:06 +00:00
John Crispin
9f14006809 ramips: add additional support for MQmaker WiTi board
The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram,
2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and
one 5 ghz antenna.

This is the 6th submission that adds support for XHCI in the device tree
file, along with switching the location of the 2 radio's and addition of
the kmod-i2c-mt7621 in the default packages of the profile.

Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>

SVN-Revision: 47845
2015-12-11 15:04:13 +00:00
John Crispin
8c1f5141ce ralink: add support for netis WF-2881
netis WF-2881 is an MT7621AT based router with MT7602EN, MT7612EN.
It has 128MB DDR3, 128MB SLC NAND FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.

this device only works on top of UBI.

Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons (reset button)
* ethernet switch and USB diag LEDs
* UART
* GPIOs
* sysupgrade

Tested and not working
* failsafe

Signed-off-by: YounJae Rho <luxflow@live.com>

SVN-Revision: 47619
2015-11-24 18:29:26 +00:00
John Crispin
e9baf8265b ramips: add support for Youku YK1
Changes since V1:
I resend this patch for current trunk.The former V1 patch is for CC branch.

Signed-off-by: Shonn Lu <countrysideboy@qq.com>

SVN-Revision: 47617
2015-11-24 18:29:02 +00:00
John Crispin
2350c149b5 ramips: add feature to blink led on sysupgrade
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47373
2015-11-03 13:32:02 +00:00
John Crispin
165244a222 ramips: add support for ZBT WG2626
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 47351
2015-11-02 10:18:19 +00:00
John Crispin
3760b95702 ramips: add support for Dovado tiny AC
Add support for Dovado tiny AC wifi router.

Soc: mt7620a
ram: 64MB
flash: 8MB
1x usb 2.0
two gigabit lan ports

5ghz wlan is not supported on this board since there is no gpl driverfor mt7610e wifi chip.

Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>

SVN-Revision: 47348
2015-11-02 10:17:51 +00:00
John Crispin
51dd991d39 ramips: add LinkIt Smart7688 support
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47203
2015-10-19 10:07:38 +00:00
John Crispin
c10bdf11ff ramips: Add base-files for HiWiFi HC5x61 models
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.

The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.

v3 fix
   1: Fixed model order
   2: Remove manufacturer name from model name
   3: Use a hacky but prettier way to get mac address.

Signed-off-by: Xiaoning Kang <kangxn@163.com>

SVN-Revision: 47111
2015-10-05 10:25:47 +00:00
John Crispin
57c5910535 ramips: Added WIZnet WizFi630A Platform based on Ralink RT5350
This patch is to add the WIZnet WizFi630A board as a new platform. The board is in mini pci express form factor.

Signed-off-by: Tobias Welz <tw@wiznet.eu>

SVN-Revision: 46921
2015-09-14 20:09:31 +00:00
John Crispin
2efdc7c896 ramips: add support for Planex DB-WRT01
This patch add support for Planex DB-WRT01. DANBOARD route on
 the MT7620A SoC with two Ethernet port and a 802.11n 2.4 GHz radio.
 DANBOARD is Cartoon character.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 46918
2015-09-14 20:08:55 +00:00
John Crispin
eba4a143c6 ramips: reorder the sysupgrade script
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46660
2015-08-17 06:18:38 +00:00
John Crispin
4069a8e49c ramips: be consistent with case statement in base-files/lib/upgrade/platform.sh
Always use "|\" (without spaces) and keep boards in alphabetical order.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46633
2015-08-17 06:01:49 +00:00
John Crispin
2fe5cf2bd6 ramips: fix 7Links PX-4885 dts{, i}, board, image and profile names
The following patch changes 7Links PX-4885 dts{,i} filenames, board, image and profile names from "PX4885" to "PX-4885" (for consistency).

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46629
2015-08-17 06:01:06 +00:00
John Crispin
e4b6dcee5e ramips: fix Buffalo WMR-300 dts, board, image and profile names
The following patch changes Buffalo WMR-300 dts filename, board, image and profile names from "WMR300" to "WMR-300" (for consistency).

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46628
2015-08-17 06:00:49 +00:00
John Crispin
713c81e97b ramips: fix Omnima models, images and profiles names
Official names for supported Omnima products are (as on website):
 * Omnima HPM
 * Omnima MiniEMBWiFi
 * Omnima MiniEMBPlug

This patch changes:
 * board names
 * dts filenames
 * profile names
 * image filenames
 * LED names

for Omnima devices, for consistency.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46627
2015-08-17 06:00:11 +00:00
John Crispin
633c46a1d4 ramips: fix Olimex models, images and profiles names
Official names for RT5350F based OLinuXino products are "RT5350F-OLinuXino{,-EVB}" as on official manufacturer website.
The following patch:
 * changes board names from "olinuxino-rt5350f{,-evb}" to "rt5350f-olinuxino{,-evb}"
 * changes filenames of dts and profile files
 * changes image filenames

for Olimex RT5350F-OLinuXino{,-EVB} devices.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46623
2015-08-17 05:59:29 +00:00
John Crispin
66f6c9e231 ramips: fix Sitecom WL-341v3 board and image names
The following patch changes:
 * board name from "wl341v3" to "wl-341v3"
 * dts filename
 * LED names in dts file

for Sitecom WL-341v3 device.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46622
2015-08-17 05:59:12 +00:00
John Crispin
a0b8c60134 ramips: fix Xiaomi MiWiFi Mini board, image and profile names
The following patch:
 * changes board name from "xiaomi-miwifi-mini" to "miwifi-mini"
 * changes filenames of dts and profile
 * fixes LED names in dts file and base-files scripts
 * removes manufacturer name from image filename

for Xiaomi MiWiFi Mini device.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46617
2015-08-17 05:58:15 +00:00
John Crispin
f38db77707 ramips: fix Zbtlink ZBT-WR8305RT board name
There is another Zbtlink board (ZBT-WA05) supported in ramips target, so use the same naming scheme for ZBT-WR8305RT board and its dts file.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46614
2015-08-17 05:57:41 +00:00
John Crispin
dcae3723fd ramips: add support for STORYLiNK SAP-G3200U3
STORYLiNK SAP-G3200U3 is an AC1200 router based on MT7621AT+MT7602EN+MT7612EN.
It has 128MB DDR3, 8MB NOR FLASH, 5-port Gbps switch and 1x USB 3.0.

The following patch adds support for this device.

Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons
* ethernet switch and USB diag LEDs
* UART
* GPIOs

Tested and not working:
* LEDs for WiFi radios (connected with WiFi chips, not supported in mt76?)
* failsafe mode (known problem, needs workaround like other MTK based devices)

More information in Wiki: http://wiki.openwrt.org/toh/storylink/sap-g3200u3

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46454
2015-07-24 09:09:22 +00:00
John Crispin
eff79253f2 ramips: add support for Planex MZK-DP150N
This patch add support for Planex MZK-DP150N.
a mini router on the MT7620A SoC with one Ethernet port and a 802.11n 2.4 GHz radio.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 46405
2015-07-17 12:51:08 +00:00
John Crispin
b618573815 ramips: adding support for OY-0001 Wireless Router
Adding support for OY-0001 Wireless Router.
OY-0001 is a wireless router made by oyewifi.com. Below is the details:
MT7620A, 128MB DDR2, 16MB FLASH, SD Slot, USB 2.0, 4 x LAN + 1 x WAN.

Signed-off-by: Tom Deng <2579131212@qq.com>

SVN-Revision: 46349
2015-07-14 07:40:22 +00:00
John Crispin
cf1fb25e67 ramips: Add Support for the Linksys RE6500
This patch adds support for the Linksys RE6500 Range Extender

http://wiki.openwrt.org/toh/linksys/re6500

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 46043
2015-06-18 18:20:56 +00:00
John Crispin
e26ba31f76 ramips: Add support for the D-Link DCS-930 B1
http://wiki.openwrt.org/toh/d-link/dcs-930l

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 46042
2015-06-18 18:20:46 +00:00
John Crispin
640b211b1e ramips: add support for PandoraBox PBR-M1
This patch is for PandoraBox PBR-M1 which is based on mt7621,
all the features work fine, including rtc, leds, button, usb3.0, etc.

Signed-off-by: tymon <banglang.huang@foxmail.com>

SVN-Revision: 46041
2015-06-18 18:20:40 +00:00
John Crispin
0ec720e9a9 ramips: Add support for RT5350F-OLinuXino V2
Version 2 : White spaces and  alphabetical order problems
 fixed
Support for Olimex RT5350F-OLinuXino Boards, tested with RT5350F-OLinuXino and RT5350F-OLinuXino-EVB boards. More Info :
 https://www.olimex.com/Products/OLinuXino/RT5350F/RT5350F-OLinuXino/open-source-hardware

Signed-off-by: Dimitar Gamishev HeHoPMaJIeH <gamishev@gmail.com>

SVN-Revision: 45902
2015-06-05 14:12:25 +00:00
Felix Fietkau
8b42d93358 ramips: implement sysupgrade support for whr-300hp2
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45842
2015-05-29 21:13:28 +00:00
John Crispin
9c86abae0e ramips: Adding support for AXIMCom MR-102N 3G/4G Travel Mobile Router
MR-102N is a RT3050F based wireless router(32M RAM + 8M NOR flash) with 1 USB
and 1 ethernet port.  The original product information can be found at:
http://www.aximcom.com/en/MR-102N

Signed-off-by:	Tai-hwa Liang <atliang@gmail.com>

SVN-Revision: 45724
2015-05-23 15:27:05 +00:00
John Crispin
5e96c2d541 ramips: add support for Comfast CF-WR800N
This patch adds support for Comfast CF-WR800N, a wall-plug wireless router
based on the MT7620N SoC with one Ethernet port and a 802.11n 2.4 GHz radio.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>

SVN-Revision: 45722
2015-05-23 15:26:39 +00:00
John Crispin
b7f19a5b26 ramips: Add support for Microduino MicroWRT
MicroWRT is an wireless router with 2 USB,1 ethernet port. It
has a 16M flash and 64M DDR2 RAM. You can use most interface, such as
i2c, SPI, i2s and PCIe. Besides that there are three expansion borad to
combine with the core board. The detailed information, please refer to
https://www.microduino.cc/wiki/index.php?title=Main_Page

This patch adds support for it.
Because there is only one port,so disabled VLAN and use eth0 as lan
port. and only a power LED control by power pin.

Signed-off-by: 盛凯 <shengkai81@gmail.com>

SVN-Revision: 45331
2015-04-09 10:32:37 +00:00
John Crispin
449c5f7b30 ramips: Add support for ZTE Q7
ZTE Q7 is a wireless router with SD Card,USB,1 ethernet port and a battery.It used MT7620a SoC.
I can,t find any information about this router on ZTE's website.
But I found this : http://en.cctairmobi.com/plus/list.php?tid=40
This router is the same as ZTE Q7 and later I found that both routers are made by the same company:-D

This patch adds support for it.
Because there is only one port,I disabled VLAN and use eth0 as lan port.
I could only create a sysupgrade firmware because I don't know how the orignal webpage check the uploaded image:-(

Signed-off-by: 郭传鈜 <gch981213@gmail.com>

SVN-Revision: 45208
2015-04-01 08:31:46 +00:00
John Crispin
3618391514 ramips: Buffalo WZR-AGL300NH target support
I got work with this patch.
Ethernet switch (includes VLAN), WiFi connected via PCIe, LEDs, buttons.

In mtd partion map of DTS file, I renamed Linux firmware regions (kernel + root squashfs) to “firmware”because it allows kernel to split kernel and roots and rootfsdata.

signed-off-by: ngc@ff.iij4u.or.jp
——
——

SVN-Revision: 44470
2015-02-16 21:19:18 +00:00
John Crispin
70db4e4639 ramips: add support for Xiaomi MiWiFi Mini devices
This patch adds support for Xiaomi MiWiFi Mini, a 802.11a/b/g/n/ac dual radio
wireless router based on the MediaTek MT7620a SoC.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>

SVN-Revision: 44238
2015-02-02 09:01:07 +00:00
John Crispin
36d19e46df ramips: add support for Tenda 3G150B
Add suport for Tenda 3G150B:
- cpu: Ralink RT5350F
- flash: 4MB
- ram: 32MB
- 1x USB 2.0
- 1x RJ45
- one reset button
- battery powered (BP-4L, 3.7V 1450mAh)

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 44073
2015-01-22 09:35:22 +00:00
John Crispin
607ecb249c ralink: add support for firewrt
this is a mt7621 based board

Signed-off-by: wengbj <linux.c@foxmail.com>

SVN-Revision: 44055
2015-01-20 06:34:28 +00:00
Felix Fietkau
40b740b232 ramips: add preliminary support for DIR-860L B1
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 44016
2015-01-17 21:20:05 +00:00
John Crispin
88df2bd2ff ramips: add support for Intenso Memory 2 Move USB 3.0
This adds support for a rt5350-based "portable nas" solution
from Intenso. The board comes with 32M RAM and 8M Flash, the
built-in HDD is connected/accessible via a usb3.0<->sata
bridge VLI VL701.

The device has 1 Ethernet port (100M/10M), 1 micro b usb 3.0
socket (for charging the battery, or accessing the hdd directly).
Wireless connectivity is provided by the rt5350 SoC [i.e.:
802.11n 1x1 2.4 GHz with a pcb antenna.]

Serial, leds, wifi, ethernet and usb are tested and
as far as I can tell: they are working fine (tm).

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

SVN-Revision: 44001
2015-01-17 14:06:13 +00:00
John Crispin
7a65864344 ralink: add support for Kingston MLWG2
This patch adds support for the Kingston Mobilelite Wireless G2 (MLWG2)

http://wiki.openwrt.org/toh/kingston/mlwg2

https://github.com/gmacario/kingston-mlwg2-hack/wiki/Testing-OpenWrt-on-MLWG2

Tested-by: Gianpaolo Macario <gmacario@gmail.com>

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 43990
2015-01-17 07:07:36 +00:00
Felix Fietkau
48d8bc4f97 ramips: add preliminary Archer C20i support
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43898
2015-01-09 15:40:51 +00:00
Felix Fietkau
ca32b89cc0 ramips: fix wsr-1166 sysupgrade support
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43816
2015-01-03 18:31:06 +00:00
John Crispin
263070a2e7 ramips:Add support for Aigale Ai-BR100
Aigale Ai-BR100 is a router with mt7620a soc.
There are only 2 lights on the board (WAN and WLAN) so I used the wlan light as the status led.

Signed-off-by: 郭传鈜 <gch981213@gmail.com>

SVN-Revision: 43681
2014-12-13 08:07:03 +00:00
John Crispin
0371dabc13 ralink: add support for WSR-600/1166
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 43244
2014-11-14 16:52:36 +00:00
Felix Fietkau
07754ac297 ramips: enable sysupgrade for whr-600d, whr-1166d
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43213
2014-11-08 12:18:58 +00:00
Imre Kaloz
d738d22bf8 add support for the Linksys E1700
SVN-Revision: 43186
2014-11-05 14:37:13 +00:00
John Crispin
cc5194cf03 ramips: add support for Airlink101 AR670W
This is a RT2880-based board, 32MB RAM, 4MB flash. The bootloader
is a hacked u-Boot that reads an LZMA image directly, so we skip
generating the uImage header and enable the lzma mtdsplit parser.

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 43153
2014-11-03 08:00:13 +00:00
John Crispin
d0bf15f235 ramips: add support for A5-V11 board (resubmit)
(Reposted due to an issue with the patchwork server during original submission)

Unbranded. Silkscreen on PCB is “A5-V11”, believed to be made by Bococom (or at least uses Bococom image encryption - as used on poray devices - but different key)

Signed-off-by: Gareth Bryan <gareth@mx9.org>

SVN-Revision: 43102
2014-10-29 11:01:17 +00:00