Commit graph

380 commits

Author SHA1 Message Date
John Crispin
4e31b2e869 ramips: add support for Ubiquiti EdgeRouter X (UBNT-ERX)
This router is based on MT7621 SoC, no wifi, no usb, nand.

Works:
* Boots.
* Ethernet.
* Switch.
* Button (reset).
* Flashing OpenWrt from stock firmware.
* Upgrading OpenWrt.

Doesn't work:
* No GPIO leds. All leds are controlled by switch,
  but stock firmware was able to control them.
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
  nand/spi drivers do not support pin sharing,
  so it is not accessable and disabled. Stock
  firmware could read it and it was empty.
* PoE out.

Router has serial pins populated. If looking at the top
of the router, then counting from Eth sockets pins go as:
'GND, RX, TX, GND'. 3.3v, 57600.

U-boot bootloader supports tftpboot, controlled from serial.
This router has two kernel partitions: 'live' and 'backup'.
They are swapped during flashing (on both stock and OpenWrt).
Active partition is controlled by a flag in a factory partition.
U-boot has custom command to switch active kernel partition.
Kernel partitions are 'bare flash' 3MB. Stock bootloader has
no UBI support. Stock rootfs is UBIFS.

Flashing procedure.
Stock firmware uses custom kernel patch to mount squashfs
from a file that is located on UBIFS volume. This makes wiping
out this volume from within stock firmware difficult.
Instead this patch builds image that is flashable by stock firmware
and contains initrams image (with minimal set of packages
to fit into kernel partition). Once this is flashed one can reboot
into initramfs OpenWrt and use sysupgrade to flash OpenWrt including
rootfs into nand.
Note: factory image is only built if initramfs image is enabled.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47881
2015-12-12 07:38:06 +00:00
John Crispin
8470e30a76 ramips: move partition definitions out of mt7621.dtsi file
Partitions defined in parent dtsi cannot be undefined in children.
This moves partitions defined in mt7621.dtsi into board's device tree.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47876
2015-12-12 06:42:11 +00:00
John Crispin
e610cdfc8a ramips: use gic timer as clocksource for mt7621
* Switches clocksource to gic timer.
* Moves frequency definitions to dtsi since frequency was hardcoded anyway
  Will work on proper frequency detection later.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47875
2015-12-12 06:42:05 +00:00
Felix Fietkau
77bedbe80d Revert "ramips: use gic timer as clocksource for mt7621"
This reverts commit 270a2afcc544ca14e79198346e7e186033472ae7.

SVN-Revision: 47872
2015-12-11 19:22:15 +00:00
John Crispin
9f14006809 ramips: add additional support for MQmaker WiTi board
The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram,
2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and
one 5 ghz antenna.

This is the 6th submission that adds support for XHCI in the device tree
file, along with switching the location of the 2 radio's and addition of
the kmod-i2c-mt7621 in the default packages of the profile.

Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>

SVN-Revision: 47845
2015-12-11 15:04:13 +00:00
John Crispin
6cbb1be464 ramips: Fix support for PBR-M1 board
The PBR-M1 support in current OpenWrt is for the early demo board and it doesn't work on the final board.This patch fixes the support for it.

The LED called pbr-m1:buzzer is a beeper connected to GPIO26 so I used gpio-beeper instead of gpio-leds.

Signed-off-by: 郭传鈜 <gch981213@gmail.com>

SVN-Revision: 47844
2015-12-11 15:03:50 +00:00
John Crispin
abd11be13c ramips: use gic timer as clocksource for mt7621
* Switches clocksource to gic timer.
* Moves frequency definitions to dtsi since frequency was hardcoded anyway
  Will work on proper frequency detection later.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47843
2015-12-11 15:03:39 +00:00
John Crispin
a87272ebfb ramips: enable CPS for mt7621
Enables CPS multiprocessing instead ob obsoleted CMP for mt7621.

This patch fixes a few issues currently existing on 4.3 kernel with at least ubnt-erx:
* iperf shows only 50Mbits on direct gigabit connection to desktop,
* ping times jump to 5-6ms to dorectly connected desktop
* /proc/interrupts shows spurious interrups (ERR)

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47842
2015-12-11 15:03:27 +00:00
John Crispin
81c999bbda ramips: mt7621: use symbolic names of gic interrupt settings
This also adds dts nodes for cpc and mc for documentation purposes

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47836
2015-12-11 15:02:13 +00:00
John Crispin
6df4426245 ralink: bump to the target to v4.3
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47831
2015-12-10 19:06:32 +00:00
John Crispin
82557aee85 ramips: adapt VoCore to new second spi device code
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 47667
2015-11-28 23:24:52 +00:00
John Crispin
8c1f5141ce ralink: add support for netis WF-2881
netis WF-2881 is an MT7621AT based router with MT7602EN, MT7612EN.
It has 128MB DDR3, 128MB SLC NAND FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.

this device only works on top of UBI.

Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons (reset button)
* ethernet switch and USB diag LEDs
* UART
* GPIOs
* sysupgrade

Tested and not working
* failsafe

Signed-off-by: YounJae Rho <luxflow@live.com>

SVN-Revision: 47619
2015-11-24 18:29:26 +00:00
John Crispin
e9baf8265b ramips: add support for Youku YK1
Changes since V1:
I resend this patch for current trunk.The former V1 patch is for CC branch.

Signed-off-by: Shonn Lu <countrysideboy@qq.com>

SVN-Revision: 47617
2015-11-24 18:29:02 +00:00
John Crispin
c550ad3d3a ramips: update dtsi files to support second spi device
Signed-off-by: Michael Lee <igvtee@gmail.com>

SVN-Revision: 47580
2015-11-22 11:49:13 +00:00
John Crispin
40ddc71cc9 ramips: init usb power for Lenovo Y1S
Signed-off-by: Shonn Lu <countrysideboy@qq.com>

SVN-Revision: 47557
2015-11-21 21:24:38 +00:00
John Crispin
dc699dd547 ramips: minor tweak to the lks7688 baord name
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47388
2015-11-05 10:01:23 +00:00
John Crispin
165244a222 ramips: add support for ZBT WG2626
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 47351
2015-11-02 10:18:19 +00:00
John Crispin
0f4b153e3d ramips: add eeprom mtd partition to the Asus RP-N53 dts
This patch adds the eeprom property to the dts for the Asus RP-N53. It is necessary to get the wifi in the soc working.

Signed-off-by:  Alberto Mattea <alberto@mattea.info>

SVN-Revision: 47350
2015-11-02 10:18:09 +00:00
John Crispin
3760b95702 ramips: add support for Dovado tiny AC
Add support for Dovado tiny AC wifi router.

Soc: mt7620a
ram: 64MB
flash: 8MB
1x usb 2.0
two gigabit lan ports

5ghz wlan is not supported on this board since there is no gpl driverfor mt7610e wifi chip.

Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>

SVN-Revision: 47348
2015-11-02 10:17:51 +00:00
John Crispin
7295e9fb8b ramips: add alsa support
add the SDK alsa driver. this has only been tested on mt7628/88 and wm8960.
mt7620 is only compile tested.

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47205
2015-10-19 10:07:54 +00:00
John Crispin
51dd991d39 ramips: add LinkIt Smart7688 support
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47203
2015-10-19 10:07:38 +00:00
John Crispin
b0f7e6bc83 ramips: fix /target/linux/ramips/dts/HC5XXX.dtsi
dtb complained about those lines

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47151
2015-10-07 08:00:40 +00:00
John Crispin
ccf89e71f2 ramips: add support for 16MB VoCore
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 47120
2015-10-05 10:27:00 +00:00
John Crispin
948e67cb16 ramips: fix size-cells for spi nodes
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 47119
2015-10-05 10:26:54 +00:00
John Crispin
e6e373d348 ramips: Add DTS files for HiWiFi HC5x61 models
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.

The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.

v3 fix
  1: Merged most stuff into dtsi file
  2: Remove unnecessary empty lines.

Signed-off-by: Xiaoning Kang <kangxn@163.com>

SVN-Revision: 47112
2015-10-05 10:25:53 +00:00
John Crispin
7ad419a9f1 ralink: add irq to mt7628 gpio node
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47076
2015-10-01 19:12:14 +00:00
John Crispin
f453508b3e ramips: Fix pinmux functions for MT7621
The pinctrl-rt2880 code doesn't support multiple functions with the same
name. This will result in a incorrect pinmux configuration.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46963
2015-09-16 08:31:52 +00:00
John Crispin
57c5910535 ramips: Added WIZnet WizFi630A Platform based on Ralink RT5350
This patch is to add the WIZnet WizFi630A board as a new platform. The board is in mini pci express form factor.

Signed-off-by: Tobias Welz <tw@wiznet.eu>

SVN-Revision: 46921
2015-09-14 20:09:31 +00:00
John Crispin
2efdc7c896 ramips: add support for Planex DB-WRT01
This patch add support for Planex DB-WRT01. DANBOARD route on
 the MT7620A SoC with two Ethernet port and a 802.11n 2.4 GHz radio.
 DANBOARD is Cartoon character.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 46918
2015-09-14 20:08:55 +00:00
Felix Fietkau
1956cc7018 ramips: enable external amplifier for Xiaomi MiWiFi Mini
Attempt to boost the 2.4 GHz signal, currently very low.

Signed-off-by: D. Andrei Măceș <dmaces@nd.edu>

SVN-Revision: 46891
2015-09-12 10:22:41 +00:00
John Crispin
1a392636a5 ramips: use consistent naming scheme for LEDs
The upstream LED naming convention is "device:color:led-name", but it seems that many of supported boards in OpenWrt don't follow this approach.
The following patch fixes this inconsistency in dts{,i} files and updates base-files scripts for ramips target:
 * fixes wrong indentation
 * keeps case statements structure in same convention as in other scripts (no empty line after ";;", no indentation for case...esac body)
 * fixes wrong LED names for some of boards (makes them the same as in dts{,i} files)
 * combines boards with same configuration (ex. set_wifi_led "rt2800pci-phy0::radio" in 01_leds)

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46664
2015-08-17 06:24:34 +00:00
John Crispin
2fe5cf2bd6 ramips: fix 7Links PX-4885 dts{, i}, board, image and profile names
The following patch changes 7Links PX-4885 dts{,i} filenames, board, image and profile names from "PX4885" to "PX-4885" (for consistency).

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46629
2015-08-17 06:01:06 +00:00
John Crispin
e4b6dcee5e ramips: fix Buffalo WMR-300 dts, board, image and profile names
The following patch changes Buffalo WMR-300 dts filename, board, image and profile names from "WMR300" to "WMR-300" (for consistency).

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46628
2015-08-17 06:00:49 +00:00
John Crispin
713c81e97b ramips: fix Omnima models, images and profiles names
Official names for supported Omnima products are (as on website):
 * Omnima HPM
 * Omnima MiniEMBWiFi
 * Omnima MiniEMBPlug

This patch changes:
 * board names
 * dts filenames
 * profile names
 * image filenames
 * LED names

for Omnima devices, for consistency.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46627
2015-08-17 06:00:11 +00:00
John Crispin
40f808600c ramips: fix Tenda W150M model name
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46625
2015-08-17 05:59:47 +00:00
John Crispin
b52ac01d27 ramips: fix Aigale Ai-BR100 dts and profile names
The following patch changes dts filename and profile name for Aigale Ai-BR100 (for consistency).

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46624
2015-08-17 05:59:36 +00:00
John Crispin
633c46a1d4 ramips: fix Olimex models, images and profiles names
Official names for RT5350F based OLinuXino products are "RT5350F-OLinuXino{,-EVB}" as on official manufacturer website.
The following patch:
 * changes board names from "olinuxino-rt5350f{,-evb}" to "rt5350f-olinuxino{,-evb}"
 * changes filenames of dts and profile files
 * changes image filenames

for Olimex RT5350F-OLinuXino{,-EVB} devices.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46623
2015-08-17 05:59:29 +00:00
John Crispin
66f6c9e231 ramips: fix Sitecom WL-341v3 board and image names
The following patch changes:
 * board name from "wl341v3" to "wl-341v3"
 * dts filename
 * LED names in dts file

for Sitecom WL-341v3 device.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46622
2015-08-17 05:59:12 +00:00
John Crispin
102073ca17 ramips: fix Argus ATP-52B board and image names
The following patch:
 * changes board name from "argus-atp52b" to "atp-52b"
 * changes dts filename
 * fixes LED names in dts file and base-files scripts
 * removes manufacturer name from image filename

for Argus ATP-52B device.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46621
2015-08-17 05:58:57 +00:00
John Crispin
5e84d173fa ramips: fix Asus RT-N56U dts filename
Other Asus RT-N dts files are named "RT-N..." (not "RTN..."), so use the same for RT-N56U.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46619
2015-08-17 05:58:35 +00:00
John Crispin
7bf1db0dcb ramips: fix UPVEL model names
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46618
2015-08-17 05:58:20 +00:00
John Crispin
a0b8c60134 ramips: fix Xiaomi MiWiFi Mini board, image and profile names
The following patch:
 * changes board name from "xiaomi-miwifi-mini" to "miwifi-mini"
 * changes filenames of dts and profile
 * fixes LED names in dts file and base-files scripts
 * removes manufacturer name from image filename

for Xiaomi MiWiFi Mini device.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46617
2015-08-17 05:58:15 +00:00
John Crispin
5e1ea4810b ramips: fix Asus WL-330N{, 3G} boards names
There are other Asus boards supported in ramips target, so use the same naming scheme for WL-330N{,3G} boards and their dts files.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46615
2015-08-17 05:57:55 +00:00
John Crispin
f38db77707 ramips: fix Zbtlink ZBT-WR8305RT board name
There is another Zbtlink board (ZBT-WA05) supported in ramips target, so use the same naming scheme for ZBT-WR8305RT board and its dts file.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46614
2015-08-17 05:57:41 +00:00
John Crispin
553fea9f19 ramips: fix indentation and other mistakes in .dts{, i} files
The following patch fixes:
 * wrong indentations
 * doubled gpio-keys-polled nodes (DIR-300-B7, DIR-320-B1, DIR-610-A1)
 * duplicate spacings
 * empty lines at end of files and after last child nodes
 * trailing and leading whitespace
 * unnecessary and commented-out code
 * missing empty lines between nodes and between properties and nodes
 * unnecessary empty lines between nodes properties [1]

in .dts{,i} files, for ramips target.

[1] Some of empty lines in SOCs dtsi files were left untouched, because they seem to be there for a reason (readability?).

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46613
2015-08-17 05:57:18 +00:00
Felix Fietkau
ba05254353 ramips: Fix Ticket #20153 swap radio calibration data pointers on the RE6500
This patch fixes weak radio signal reported by nikola.georgiev

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 46545
2015-08-02 15:08:14 +00:00
Felix Fietkau
92c41de105 ramips: swap radio calibration data pointers for DIR-860L
Fixes low 5 GHz tx power issues

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 46497
2015-07-26 13:01:43 +00:00
John Crispin
1b6a6abf04 ramips: add additional uarts to mt7628.dtsi
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46477
2015-07-24 09:12:21 +00:00
John Crispin
dcae3723fd ramips: add support for STORYLiNK SAP-G3200U3
STORYLiNK SAP-G3200U3 is an AC1200 router based on MT7621AT+MT7602EN+MT7612EN.
It has 128MB DDR3, 8MB NOR FLASH, 5-port Gbps switch and 1x USB 3.0.

The following patch adds support for this device.

Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons
* ethernet switch and USB diag LEDs
* UART
* GPIOs

Tested and not working:
* LEDs for WiFi radios (connected with WiFi chips, not supported in mt76?)
* failsafe mode (known problem, needs workaround like other MTK based devices)

More information in Wiki: http://wiki.openwrt.org/toh/storylink/sap-g3200u3

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46454
2015-07-24 09:09:22 +00:00
John Crispin
eff79253f2 ramips: add support for Planex MZK-DP150N
This patch add support for Planex MZK-DP150N.
a mini router on the MT7620A SoC with one Ethernet port and a 802.11n 2.4 GHz radio.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 46405
2015-07-17 12:51:08 +00:00
John Crispin
5e1c7fb0cc ramips: added gpio spi refclk support for wrtnode board
This syncs the dts file with the one provided by the wrtnode team:
https://github.com/WRTnode/openwrt-patches/blob/master/R41508/wrtnode_factory_firmware_dts.patch

Signed-off-by: Christian Mehlis <christian@m3hlis.de>

SVN-Revision: 46359
2015-07-14 09:57:08 +00:00
John Crispin
1aca6e6b27 ramips: added led support for wrtnode board
This syncs the dts file with the one provided by the wrtnode team:
https://github.com/WRTnode/openwrt-patches/blob/master/R41508/wrtnode_factory_firmware_dts.patch

Signed-off-by: Christian Mehlis <christian@m3hlis.de>

SVN-Revision: 46350
2015-07-14 07:41:19 +00:00
John Crispin
b618573815 ramips: adding support for OY-0001 Wireless Router
Adding support for OY-0001 Wireless Router.
OY-0001 is a wireless router made by oyewifi.com. Below is the details:
MT7620A, 128MB DDR2, 16MB FLASH, SD Slot, USB 2.0, 4 x LAN + 1 x WAN.

Signed-off-by: Tom Deng <2579131212@qq.com>

SVN-Revision: 46349
2015-07-14 07:40:22 +00:00
John Crispin
0ac2ef13f7 ramips: mt7620 ArcherC20i USB support
USB port of TP-Link Archer C20i does not work with trunk and CC.
This patch adds two nodes (ehci and ohci) to the device tree enabling USB.

Signed-off-by: Gunnar Thorburn <gunnar@thorburn.se>

SVN-Revision: 46348
2015-07-14 07:39:19 +00:00
John Crispin
cf1fb25e67 ramips: Add Support for the Linksys RE6500
This patch adds support for the Linksys RE6500 Range Extender

http://wiki.openwrt.org/toh/linksys/re6500

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 46043
2015-06-18 18:20:56 +00:00
John Crispin
e26ba31f76 ramips: Add support for the D-Link DCS-930 B1
http://wiki.openwrt.org/toh/d-link/dcs-930l

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 46042
2015-06-18 18:20:46 +00:00
John Crispin
640b211b1e ramips: add support for PandoraBox PBR-M1
This patch is for PandoraBox PBR-M1 which is based on mt7621,
all the features work fine, including rtc, leds, button, usb3.0, etc.

Signed-off-by: tymon <banglang.huang@foxmail.com>

SVN-Revision: 46041
2015-06-18 18:20:40 +00:00
John Crispin
0ec720e9a9 ramips: Add support for RT5350F-OLinuXino V2
Version 2 : White spaces and  alphabetical order problems
 fixed
Support for Olimex RT5350F-OLinuXino Boards, tested with RT5350F-OLinuXino and RT5350F-OLinuXino-EVB boards. More Info :
 https://www.olimex.com/Products/OLinuXino/RT5350F/RT5350F-OLinuXino/open-source-hardware

Signed-off-by: Dimitar Gamishev HeHoPMaJIeH <gamishev@gmail.com>

SVN-Revision: 45902
2015-06-05 14:12:25 +00:00
Felix Fietkau
4746e539e0 ramips: fix the memory map on FireWRT
Avoid the use of memory marked as reserved

MT7621 support 512MB memory.
According to "MT7621_ProgrammingGuide_Preliminary_Platform.pdf"
0x0~0x1c000000        448MB
0x20000000~0x4000000  64MB
total 512MB

Signed-off-by: wengbj <fl.service@t-firefly.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45892
2015-06-05 08:07:41 +00:00
Felix Fietkau
69d79ea951 ramips: use highmem on the FireWRT board
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45890
2015-06-04 21:45:24 +00:00
Felix Fietkau
e56b6f6e66 ramips: fix swapped colors for router LED on WHR-1166D (thx, Björn)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45847
2015-05-30 09:39:37 +00:00
Felix Fietkau
1e659c29ec ramips: rename status led to wifi on WHR-300HP2, WHR-1166D, WHR-600D
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45846
2015-05-30 09:01:41 +00:00
Felix Fietkau
a6df9f0472 ramips: fix buttons on WHR-300HP2, WHR-1166D, WHR-600D
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45845
2015-05-29 22:42:32 +00:00
Felix Fietkau
420cdb3783 ramips: fix partition layout of WHR-300HP2, WHR-1166D, WHR-600D
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45843
2015-05-29 21:25:23 +00:00
John Crispin
9c86abae0e ramips: Adding support for AXIMCom MR-102N 3G/4G Travel Mobile Router
MR-102N is a RT3050F based wireless router(32M RAM + 8M NOR flash) with 1 USB
and 1 ethernet port.  The original product information can be found at:
http://www.aximcom.com/en/MR-102N

Signed-off-by:	Tai-hwa Liang <atliang@gmail.com>

SVN-Revision: 45724
2015-05-23 15:27:05 +00:00
John Crispin
4810f3f803 ramips: fix switch names for several boards in device tree
Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 45723
2015-05-23 15:26:51 +00:00
John Crispin
5e96c2d541 ramips: add support for Comfast CF-WR800N
This patch adds support for Comfast CF-WR800N, a wall-plug wireless router
based on the MT7620N SoC with one Ethernet port and a 802.11n 2.4 GHz radio.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>

SVN-Revision: 45722
2015-05-23 15:26:39 +00:00
Felix Fietkau
d808d9be86 ramips: switch WSR-1166 and WSR-600 to single-firmware mtd layout
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45507
2015-04-19 16:31:54 +00:00
John Crispin
b7f19a5b26 ramips: Add support for Microduino MicroWRT
MicroWRT is an wireless router with 2 USB,1 ethernet port. It
has a 16M flash and 64M DDR2 RAM. You can use most interface, such as
i2c, SPI, i2s and PCIe. Besides that there are three expansion borad to
combine with the core board. The detailed information, please refer to
https://www.microduino.cc/wiki/index.php?title=Main_Page

This patch adds support for it.
Because there is only one port,so disabled VLAN and use eth0 as lan
port. and only a power LED control by power pin.

Signed-off-by: 盛凯 <shengkai81@gmail.com>

SVN-Revision: 45331
2015-04-09 10:32:37 +00:00
John Crispin
449c5f7b30 ramips: Add support for ZTE Q7
ZTE Q7 is a wireless router with SD Card,USB,1 ethernet port and a battery.It used MT7620a SoC.
I can,t find any information about this router on ZTE's website.
But I found this : http://en.cctairmobi.com/plus/list.php?tid=40
This router is the same as ZTE Q7 and later I found that both routers are made by the same company:-D

This patch adds support for it.
Because there is only one port,I disabled VLAN and use eth0 as lan port.
I could only create a sysupgrade firmware because I don't know how the orignal webpage check the uploaded image:-(

Signed-off-by: 郭传鈜 <gch981213@gmail.com>

SVN-Revision: 45208
2015-04-01 08:31:46 +00:00
John Crispin
21e0f98903 ralink: add default pinctrl node for mt7621 eval kit
fixes #19213

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 45022
2015-03-26 12:23:02 +00:00
John Crispin
024e0c1835 ralink: add FireWRT power button
Signed-off-by: Jay Weng <fl.service@t-firefly.com>

SVN-Revision: 45019
2015-03-26 10:59:36 +00:00
Felix Fietkau
dac483acb4 ramips: fix WSR-1166 green power LED
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 44898
2015-03-19 21:51:44 +00:00
John Crispin
553528371b ralink: fix mt7621 i2c name
Signed-off-by: zouxf <fl.service@t-firefly.com>

SVN-Revision: 44868
2015-03-17 09:44:14 +00:00
John Crispin
800da5a02e ralink: add wifi 5g dts info for cy-swr1100
Signed-off-by: michael lee <igvtee@gmail.com>

SVN-Revision: 44739
2015-03-13 08:37:45 +00:00
John Crispin
835b17c333 ralink: resize the flash partition for FireWRT
Signed-off-by: wengbj <fl.service@t-firefly.com>

SVN-Revision: 44691
2015-03-12 10:06:31 +00:00
John Crispin
260dea38fb ralink: add FireWRT IO multiplexing
Signed-off-by: wengbj <fl.service@t-firefly.com>

SVN-Revision: 44660
2015-03-11 15:55:16 +00:00
John Crispin
64db436416 ramips: fix the mt7628 dts file
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44494
2015-02-19 14:04:41 +00:00
John Crispin
3618391514 ramips: Buffalo WZR-AGL300NH target support
I got work with this patch.
Ethernet switch (includes VLAN), WiFi connected via PCIe, LEDs, buttons.

In mtd partion map of DTS file, I renamed Linux firmware regions (kernel + root squashfs) to “firmware”because it allows kernel to split kernel and roots and rootfsdata.

signed-off-by: ngc@ff.iij4u.or.jp
——
——

SVN-Revision: 44470
2015-02-16 21:19:18 +00:00
John Crispin
4ce7053b2b ramips: Kingston MLW221 and MLWG2 cleanup
MLW221 dts use tabs NOT spaces.
MLWG2 dts typo and 1 tab not spaces
01_leds and diag.sh cleanup

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 44356
2015-02-09 12:15:45 +00:00
John Crispin
2c03605028 ramips: fix mt76 radio pcie location definition for in Xiaomi MiWiFi Mini
This patch sets the correct location of the mt76 radio in the pcie bridge
(pcie-bridge instead of pcie0). Additionaly, it disables the 2.4 GHz band.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>

SVN-Revision: 44355
2015-02-09 12:15:17 +00:00
John Crispin
2dd7bce338 ramips: Add mt76 node for Lenovo Y1 and Y1S.
Both Y1 and Y1S have MT7612E wireless chip so I submitted this patch.
Tested on Lenovo Y1.

Signed-off-by: 郭传鈜 <gch981213@gmail.com>

SVN-Revision: 44354
2015-02-09 12:15:00 +00:00
John Crispin
654bc380ec ralink: add 3.18 support
keep default as 3.14, mt7621 gic need to be ported to 3.18

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44349
2015-02-09 12:13:55 +00:00
John Crispin
043f462be4 ralink: add FireWRT button detail
Signed-off-by: wengbj <fl.service@t-firefly.com>

SVN-Revision: 44242
2015-02-02 09:02:16 +00:00
John Crispin
d725678a43 ralink: add FireWRT led detail
Signed-off-by: wengbj <fl.service@t-firefly.com>

SVN-Revision: 44241
2015-02-02 09:02:10 +00:00
John Crispin
1258b4cc94 ralink: add ethernet macaddr to dts for FireWRT
Signed-off-by: wengbj <fl.service@t-firefly.com>

SVN-Revision: 44240
2015-02-02 09:02:02 +00:00
John Crispin
70db4e4639 ramips: add support for Xiaomi MiWiFi Mini devices
This patch adds support for Xiaomi MiWiFi Mini, a 802.11a/b/g/n/ac dual radio
wireless router based on the MediaTek MT7620a SoC.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>

SVN-Revision: 44238
2015-02-02 09:01:07 +00:00
John Crispin
36d19e46df ramips: add support for Tenda 3G150B
Add suport for Tenda 3G150B:
- cpu: Ralink RT5350F
- flash: 4MB
- ram: 32MB
- 1x USB 2.0
- 1x RJ45
- one reset button
- battery powered (BP-4L, 3.7V 1450mAh)

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 44073
2015-01-22 09:35:22 +00:00
John Crispin
deb66a555e ramips: improve and fix Memory 2 Move support
This patch is a follow up for my previous patch:
"ramips: add support for Intenso Memory 2 Move USB 3.0".

It fixes a couple of errors in the DTS (one of which broke
the gpio-buttons). The kmod-leds-gpio dependency has been
dropped as it is already part of the ramips target.

Furthermore the ramdisk/uImage image is generated by default
for the rt3050 subtarget. This image is needed to flash
OpenWrt for the first time onto the device via TFTP.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

SVN-Revision: 44072
2015-01-22 09:35:12 +00:00
John Crispin
607ecb249c ralink: add support for firewrt
this is a mt7621 based board

Signed-off-by: wengbj <linux.c@foxmail.com>

SVN-Revision: 44055
2015-01-20 06:34:28 +00:00
Felix Fietkau
69ee1807ed ralink: add ethernet fe and esw reset control bit
Signed-off-by: michael lee <igvtee@gmail.com>

SVN-Revision: 44042
2015-01-18 20:16:44 +00:00
Felix Fietkau
40b740b232 ramips: add preliminary support for DIR-860L B1
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 44016
2015-01-17 21:20:05 +00:00
Felix Fietkau
590e0d7f81 ramips: register mt76 device tree info for WSR-1166DHP
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 44010
2015-01-17 16:50:59 +00:00
Felix Fietkau
070f67aa9b ramips: register mt7621 pcie through device tree
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 44009
2015-01-17 16:50:51 +00:00
John Crispin
88df2bd2ff ramips: add support for Intenso Memory 2 Move USB 3.0
This adds support for a rt5350-based "portable nas" solution
from Intenso. The board comes with 32M RAM and 8M Flash, the
built-in HDD is connected/accessible via a usb3.0<->sata
bridge VLI VL701.

The device has 1 Ethernet port (100M/10M), 1 micro b usb 3.0
socket (for charging the battery, or accessing the hdd directly).
Wireless connectivity is provided by the rt5350 SoC [i.e.:
802.11n 1x1 2.4 GHz with a pcb antenna.]

Serial, leds, wifi, ethernet and usb are tested and
as far as I can tell: they are working fine (tm).

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

SVN-Revision: 44001
2015-01-17 14:06:13 +00:00
John Crispin
7a65864344 ralink: add support for Kingston MLWG2
This patch adds support for the Kingston Mobilelite Wireless G2 (MLWG2)

http://wiki.openwrt.org/toh/kingston/mlwg2

https://github.com/gmacario/kingston-mlwg2-hack/wiki/Testing-OpenWrt-on-MLWG2

Tested-by: Gianpaolo Macario <gmacario@gmail.com>

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 43990
2015-01-17 07:07:36 +00:00
John Crispin
56a54515df ramips: add i2c pingroup to the pinmux for rt-n14u
i2c pins are wired to wps a reset button

Signed-off-by: Pavel Löbl <lobl.pavel@gmail.com>

SVN-Revision: 43985
2015-01-17 07:06:59 +00:00
Felix Fietkau
48d8bc4f97 ramips: add preliminary Archer C20i support
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43898
2015-01-09 15:40:51 +00:00
John Crispin
2120e48e75 ramips: Fix HooToo HT-TM02 support.
- Fix LED definitions.
- Add mode-switch slider definition (at GPIO 14).
- Remove unneeded VLAN now that the ethernet driver is fixed and TCP packets get passed correctly now. (This router only has one port.)
- Fix LAN port MAC address, which is defined in the factory partition as WLAN MAC address + 1.
- Fix board name, as the company name is HooToo and not HOOTOO.
- Remove unnecessary packages from the profile. (The end-user is supposed to use mechanisms such as the ImageBuilder in order to add his own set of packages to his own images... while the precompiled images should just contain the core set of packages needed to run the base functions of a wireless router.)

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 43883
2015-01-08 20:26:20 +00:00
John Crispin
2ea64717e2 ramips: update BR-6475ND dts
Update firmware location for 2.4GHz radio on the Edimax BR-6475nD.

Signed-off-by: Christopher Lais <chris+openwrt@zenthought.org>

SVN-Revision: 43881
2015-01-08 20:26:02 +00:00
Felix Fietkau
fd7be4073a ramips: fix WSR-600DHP flash layout
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43819
2015-01-03 18:31:27 +00:00
Felix Fietkau
373c84c30b ramips: fix WSR-1166DHP flash layout
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43818
2015-01-03 18:31:17 +00:00
Felix Fietkau
ada0452b14 ramips: fix WSR-{600,1166} names
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43817
2015-01-03 18:31:11 +00:00
Felix Fietkau
88e8f99f7f ramips: on mt7621 only enable xhci for the eval board (still needs patch cleanup to take effect)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43815
2015-01-03 18:30:57 +00:00
Felix Fietkau
81e3014e6d ramips: rework and fix m25p80 chunked-io support
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43808
2015-01-02 21:53:02 +00:00
John Crispin
0ffb7323d0 ralink: remove partitoon map from mt7621.dtsi
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 43720
2014-12-15 15:55:37 +00:00
John Crispin
6f2b7567b8 ralink: drop old pinmux nodes from dts files
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 43701
2014-12-14 08:57:16 +00:00
John Crispin
263070a2e7 ramips:Add support for Aigale Ai-BR100
Aigale Ai-BR100 is a router with mt7620a soc.
There are only 2 lights on the board (WAN and WLAN) so I used the wlan light as the status led.

Signed-off-by: 郭传鈜 <gch981213@gmail.com>

SVN-Revision: 43681
2014-12-13 08:07:03 +00:00
John Crispin
b1f7a027da ralink: make uartf functional on AWM002
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 43664
2014-12-12 16:17:03 +00:00
John Crispin
8a123f6f66 ramips: generate factory images for Nexx devices
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>

SVN-Revision: 43541
2014-12-07 16:53:22 +00:00
John Crispin
d04c4a311e ralink: mt7621 is a 1004Kc
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 43514
2014-12-03 20:22:42 +00:00
John Crispin
32d4348540 ralink: fix pcie reset
some old mt7620a uboots dont reset the pcie core properly. work around this
issue in the kernel driver.

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 43292
2014-11-17 16:27:48 +00:00
Felix Fietkau
28b26fa603 ramips: disable 2.4 ghz on 802.11ac wifi on WHR-1166D
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43283
2014-11-16 12:26:53 +00:00
Felix Fietkau
b3f2d3d01b ramips: use mediatek,mtd-eeprom instead of ralink for mt76
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43282
2014-11-16 12:26:47 +00:00
John Crispin
c073bf6bdf ralink: few updates tot he sdhci probe code
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 43275
2014-11-15 14:35:32 +00:00
John Crispin
66463a5b5d ralink: update pcie driver to load ranges from dts
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 43249
2014-11-14 16:53:07 +00:00
John Crispin
0371dabc13 ralink: add support for WSR-600/1166
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 43244
2014-11-14 16:52:36 +00:00
John Crispin
bfcdc8711c ralink: fix up dts for mt7621 eval board
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 43238
2014-11-12 14:55:00 +00:00
John Crispin
45814d150a ralink: more mt7530 fixes
make 1166 wan port work. this broke due to the esw_polling bug

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 43236
2014-11-11 11:46:16 +00:00
Luka Perkov
494c6e7f6e ralink: update DCS-930 dts
* read MAC address from factory partition
* remove port defines since there is only one port (most likely C/P error)

Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 43231
2014-11-11 00:05:14 +00:00
Felix Fietkau
455ba77b6a ramips: add eeprom data for 802.11ac wlan on WHR-1166D
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43218
2014-11-08 14:15:49 +00:00
Felix Fietkau
29f71d384f ramips: add missing size/address-cells to device tree include files
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43217
2014-11-08 14:15:44 +00:00
John Crispin
503a34ca50 ralink: fix the compat string for mt7620a pci
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 43211
2014-11-08 12:12:05 +00:00
John Crispin
c32ad22e40 ralink: improve r43200
r43200 tries to detect if the fixup is needed or not. control the behaviour via
OF instead and disable unused ports.

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 43201
2014-11-06 12:19:53 +00:00
John Crispin
78b6222851 ralink: tweak e1700 dts file
the current driver code wont know which mt7530 to apply the llllw setting to.

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 43199
2014-11-06 09:31:45 +00:00
John Crispin
c5954fc510 ralink: make pci driver handle mt7628
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 43198
2014-11-06 09:31:37 +00:00
John Crispin
cadf517107 ralink: add support for mt7628
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 43197
2014-11-06 09:31:31 +00:00
Imre Kaloz
d738d22bf8 add support for the Linksys E1700
SVN-Revision: 43186
2014-11-05 14:37:13 +00:00
John Crispin
b25b58a96a ralink: add pci bidge node to mt7620a dts file
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 43172
2014-11-03 20:20:46 +00:00
John Crispin
cc142739f2 ralink: fix wan port on whr-1166
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 43171
2014-11-03 20:20:40 +00:00
John Crispin
cc5194cf03 ramips: add support for Airlink101 AR670W
This is a RT2880-based board, 32MB RAM, 4MB flash. The bootloader
is a hacked u-Boot that reads an LZMA image directly, so we skip
generating the uImage header and enable the lzma mtdsplit parser.

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 43153
2014-11-03 08:00:13 +00:00
John Crispin
d0bf15f235 ramips: add support for A5-V11 board (resubmit)
(Reposted due to an issue with the patchwork server during original submission)

Unbranded. Silkscreen on PCB is “A5-V11”, believed to be made by Bococom (or at least uses Bococom image encryption - as used on poray devices - but different key)

Signed-off-by: Gareth Bryan <gareth@mx9.org>

SVN-Revision: 43102
2014-10-29 11:01:17 +00:00
John Crispin
7bac455a4c ramips: add support for Nexx WT3020 devices
SVN-Revision: 42983
2014-10-20 06:28:48 +00:00
Felix Fietkau
35e9d448f2 ramips: fix usercfg partition offset for WHR-1166D
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42958
2014-10-19 08:45:56 +00:00
John Crispin
06a849575d ralink: Build 8M image for 7Links PX-4885
7Links PX-4885 (clones) can also be purchased with 8MB flash.
Creating images for these routers, use dtsi for common part

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 42892
2014-10-13 19:41:36 +00:00
John Crispin
af1207b58c ramips: add support for Nexx WT1520
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>

SVN-Revision: 42867
2014-10-10 08:56:43 +00:00
John Crispin
d76b7e0221 ramips: D-Link DIR-810L: make led naming consistent with other boards
Signed-off-by: Michael Heimpold <mhei@heimpold.de>

SVN-Revision: 42789
2014-10-06 04:52:36 +00:00
John Crispin
b04bb3eea7 ramips: Support for RAMIPS based Tripmate HT-TM02 board
Provides support for the Tripmate HT-TM02 personal router including LEDs and
reset button. “Mode” switch is not supported. New profile includes full set
of packages required to enable LEDs, USB, and LUCI. Patches were applied
against trunk snapshot r42649. Functionality has been tested in AP, basic wifi
client, wifi router, and routed client modes - all good.

Signed-off-by: Ron Curry <wingspinner@gmail.com>

SVN-Revision: 42785
2014-10-06 04:52:07 +00:00
John Crispin
d4cc995c53 ramips: D-Link DIR-810L. Add support for SoC 2.4 GHz wireless and fix leds naming
SVN-Revision: 42619
2014-09-19 11:07:08 +00:00
John Crispin
d1f8b9bd76 ralink: DIR-645 picks up incorrect MAC address in DTS file
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42321
2014-08-28 09:19:56 +00:00
John Crispin
0c14bea523 ralink: the mt7620 evb has a usb port
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42293
2014-08-25 16:31:13 +00:00
John Crispin
fdc41e2fd7 ramips: enable second SPI for VoCore
This patch enables the second SPI as spidev and also fixes some typos.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 42277
2014-08-25 06:35:46 +00:00
John Crispin
a3fd3dc796 ramips: second spi device on rt5350
This is based on Jon Smirl's patch with the following changes:
- Set CS polarity as low by default.
- Add support for changing CS polarity.
- Add support for changing LSB/MSB.
- Add support for changing SPI mode.
- Fix indentations.

I tested it on a VoCore. Works fine connected to a second flash, but fails to detect MMC/SD cards due to SPI clock speed.

Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 42276
2014-08-25 06:35:42 +00:00
John Crispin
e9e519a147 ramips: fix OMNI-PLUG.dts
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42232
2014-08-21 06:41:27 +00:00
John Crispin
d04cab8dfc ramips: Add support for Omnima MiniPlug
This patch adds support for the Omnima MiniPlug RT5350 based board, 8MB SPI flash

Signed-off-by: Ivan Ignjatic<ivan@omnima.co.uk>

SVN-Revision: 42200
2014-08-18 16:06:48 +00:00
John Crispin
bb9a23aca2 ramips: Hame: change LED name mpr-x -> hame
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 42190
2014-08-18 13:09:39 +00:00
John Crispin
f80312613d ramips: enable additional GPIOs on HAME MPR-A1
According to the pcb tracing results[1] by anton.rad[2] MPR-A1s expose
6 unused GPIOs, only one of them working as configured in the current
DTS. This patch enables GPIO22-26.

Tested on hardware.

[1] http://i.imgur.com/kHVW2Ox.jpg
[2] https://forum.openwrt.org/viewtopic.php?pid=222698#p222698

Signed-off-by: Paul Fertser <fercerpav@gmail.com>

SVN-Revision: 42178
2014-08-18 13:08:48 +00:00
John Crispin
997ca19fd2 ralink: revert r37163
https://dev.openwrt.org/ticket/17071

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42036
2014-08-07 12:38:20 +00:00
John Crispin
04e4ff282a ramips:support Lenovo AC1200 Wireless router
Lenovo AC1200 series has two types, Y1 and Y1S.
Y1S has 256MB DDR2, Y1 only has 128MB and Y1 have no Giga Port.

Signed-off-by: Lintel <lintel.huang@gmail.com>

SVN-Revision: 41961
2014-08-03 11:13:52 +00:00
John Crispin
21845cb45d ramips: Add support for VoCore
This is based and tested on VoCore Alpha, but other stuff like status/eth LEDs are present on the final board revision + VoDock.
All GPIOs are exported, except spi/i2c.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 41939
2014-08-01 20:51:24 +00:00