When sta is configured, hostapd receives 'stop' and 'update' command from
wpa_supplicant. In the update command, hostapd gets sta parameters with
which it configures ap.
Problem is, with the default wireless configuration:
mode:11g freq:2.4GHz channel:1
If sta is connected to 5GHz network, then ap does not work. Ideally with
340-reload_freq_change.patch hostapd should reload the frequency changes
and start ap in 5GHz, but ap becomes invisible in the network.
This issue can be reproduced with following /etc/config/wireless:
config wifi-device radio0
option type mac80211
option channel 1
option hwmode 11g
option path 'virtual/uccp420/uccwlan'
option htmode 'none'
config wifi-iface 'ap'
option device 'radio0'
option encryption 'none'
option mode 'ap'
option network 'ap'
option ssid 'MyTestNet'
option encryption none
config wifi-iface 'sta'
option device radio0
option network sta
option mode sta
option ssid TestNet-5G
option encryption psk2
option key 12345
This change updates current_mode structure based on configured hw_mode
received from wpa_supplicant. Also prepare rates table after frequency
selection.
Signed-off-by: Abhilash Tuse <Abhilash.Tuse@imgtec.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup, patch refresh]
A number of small tweaks & improvements on the way to a final release.
Most notable:
Improve DHCPv4 address-in-use check.
Remove the recently introduced RFC-6842 (Client-ids in DHCP replies)
support as it turns out some clients are getting upset.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
9268ca6 ndp: don't trigger IPv6 ping when neighbor entry is invalid
2b3355f ndp: fix adding proxy neighbor entries
7dff5b4 ndp: fix wrong interface name in syslog message
a54afb5 dhcpv6-ia: Fix segfault when writing DHCPv4 leases in state file
c0e9dbf ubus: don't segfault when there're no leases
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Configuring dhcp_option as an option does not allow the usage of white
spaces in the option value; fix this by supporting dhcp_option as a list
config while still supporting the option config to maintain backwards
compatibility
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Install procd interface triggers only for interfaces which are enabled
so dropbear instances running on (an) enabled interface(s) are not
restarted due to an interface trigger of an interface which is disabled.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
minor/cosmetic: fixes the following misleading message:
root@box:~ /etc/init.d/dnsmasq restart
sh: out of range
Signed-off-by: Bastian Bittorf <bb@npl.de>
Update OpenVPN to 2.4.1
Remove 200-small_build_enable_occ.patch as it's included upstream.
Refresh patches
Add mirror and switch to HTTPS
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Similar to odhcpd, allow using ISC DHCPd instead of dnsmasq.
Disable DHCP and/or DHCP6 in case ISC DHCP is present and
enabled.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The relay section should use the logical interface name and
not the linux network device name directly. This to be
consistent with other sections of the dnsmasq config where
'interface' means the logical interface.
Signed-off-by: Karl Vogel <karl.vogel@gmail.com>
This change protects the openvpn instances to be marked as "in a crash
loop" and thereby the connection retries will run infinitely.
When the remote site of an openvpn connection goes down for some time
(network failure etc.) the openvpn instance in an openwrt/lede device
should not stop retrying to establish the connection.
With the current limit of 5 retries, there is a user interaction
required, which isn't really what you want when the device should
simply do everything to keep the vpn connection up.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This includes following changes:
480d7bc Fix sending unicast questions on cache expire
a0403cd Keep source sockaddr for every cached DNS record
1478293 Fix code freeing cached non-A(AAA) records too early
9f1cc22 Fix replying to "QU" questions received on unicast interface
943bedb Fix reading port of incoming packets
c725494 Use MCAST_PORT define for port 5353
ce7e9e9 Use one define for DNS-Based Service Discovery service name
e1bacef Drop entries cached for interface we're going to delete
496aeba Fix comment typo in cache_gc_timer
f89986b Fix refreshing cached A(AAA) records that expire
Previous updates made umdns work as expected on startup but there were
still many bugs. They were mostly related to runtime - cache management
and requests + responses. E.g. umdns was never able to send question on
DNS record expire. It was also ignoring all incoming unicast questions.
Since these issues are quite serious it makes sense to backport this
update to the stable branch.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
If noresolv is set, we should not generate a --resolv-file parameter.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [minor cleanup]
This includes 3 cleanups:
fd5a160 Don't cache hosts as services
80dd246 Refresh DNS records A and AAAA directly
6515101 Access cached records (instead of services) to read list of hosts
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This fixes crash in interface_start caused by freeing interface in
interface_free without stopping a timeout.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
RFC 6761 defines a number of top level domains should not be forwarded
to the Internet's domain servers since they are not responsible for
those domains.
This change adds a list of domains that will be blocked when 'boguspriv'
is used and augments that which is already blocked by dnsmasq's notion
of 'local service' using '--bogus-priv' i.e. RFC 1918 private addresses
and IPv6 prefixes as defined in RFC 6303.
To make this configurable rather than hard coded in dnsmasq's init
script, a new file /usr/share/dnsmasq/rfc6761.conf is conditionally
included.
The default file matches the RFC 6761 recommendation along with a few
other top level domains that should not be forwarded to the Internet.
Compile & run tested Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Honour the parent interfaces peerdns option when spawning a virtual DHCPv6
interface in order to avoid pulling in IPv6 DNS servers when the user opted
to inhibit peer DNS servers in the configuration.
Fixes#597.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
--bogus-priv now applies to IPv6 prefixes as specified in RFC6303 - this
is significantly friendlier to upstream servers.
CNAME fix in auth mode - A domain can only have a CNAME if it has no
other records
Drop 2 patches now included upstream.
Compile & run tested Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
- Fix eap test to work with standalone hostapd builds
- Fix 11n test to check the correct define
- Add 11ac, 11r and 11w tests
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
New test release (since test1) includes 2 LEDE patches that are
upstream and may be dropped, along with many spelling fixes.
Add forthcoming 2017 root zone trust anchor to trust-anchors.conf.
Backport 2 patches that just missed test3:
Reduce logspam of those domains handled locally 'local addresses only'
Implement RFC-6842 (Client-ids in DHCP replies)
Compile & run tested Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
This update includes numerous small fixes for:
1) Interfaces setup
2) Packets parsing
3) Sending replies
Without this there were multiple problems with exchanging information
between (u)mdns and other implementations (including (u)mdns as well).
This also follows project rename to umdns which was required to avoid
confusion with Apple's mdnsd from mDNSResponder project.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
as we do for IPv4 PPP interfaces. When we create the
dynamic IPv6 interface we should inherit ip6table from
main interface.
Signed-off-by: Ulrich Weber <ulrich.weber@riverbed.com>
pppoe-discovery performs the same discovery process as pppoe, but does
not initiate a session
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The only HMACs currently available use MD5 and SHA1, both of which have known
weaknesses. We already compile in the SHA256 code since we use Curve25519
by default, so there's no significant size penalty to enabling this.
Signed-off-by: Joseph C. Sible <josephcsible@users.noreply.github.com>
Bump to dnsmasq 2.77test1 - this includes a number of fixes since 2.76
and allows dropping of 2 LEDE carried patches.
Notable fix in rrfilter code when talking to Nominum's DNS servers
especially with DNSSEC.
A patch to switch dnsmasq back to 'soft fail' for SERVFAIL responses
from dns servers is also included. This mean dnsmasq tries all
configured servers before giving up.
A 'localise queries' enhancement has also been backported (it will
appear in test2/rc'n') this is especially important if using the
recently imported to LEDE 'use dnsmasq standalone' feature 9525743c
I have been following dnsmasq HEAD ever since 2.76 release.
Compile & Run tested: ar71xx, Archer C7 v2
Tested-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
ref commit 9525743c07
dnsmasq: make DHCPv6 viable for standalone dnsmasq install
Above commit broke instancing by missing filter_dnsmasq()
as part of the dhcp_add() execution.
Signed-off-by: Eric Luehrsen <ericluehrsen@hotmail.com>
Do not spam the syslog with DHCPv6 lease info if quietdhcp option
is selected. This already works for DHCPv4, make it work in the same
way for DHCPv6.
Signed-off-by: Arjen de Korte <build+lede@de-korte.org>
[Originally written by Arjen de Korte on GitHub but had issues providing
a SoB in correct format.]
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
key_direction shows up as an openvpn option in the user-interface but does not end up in the /var/etc/openvpn*.conf file. Adding it to the list here fixed the issue for me.
Signed-off-by: Brandon Koepke <bdkoepke@fastmail.com>
samba.org has started to enforce https and
currently plain http downloads with curl/wget fail,
so convert samba.org download links to use https.
Modernise links at the same time.
Also convert samba.org URL fields to have https.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
dnsmasq has sufficient services to meet the needs of DHCP
and RA with IP6 for single router router users. This is
the most common use for consumer routers. Its reenforced
as most ISP tend to only DHCP-PD /64. dnsmasq has year
over year demonstrated great flexibility in its option
set, and support for off-standard DHCP clients.
odhcpd has enhanced capabilities focused on IP6 such
as DHCP/RA relay and NDP proxy. However, it is not as
flexible in its option set. odhcpd is not as forgiving
with off-standard DHCP clients. Some points may represent
a long term TODO list, but it is the state currently.
These changes make any such combination possible. Already
odhcpd can be set as the main dhcp server. Now odhcpd
can be removed or disabled and dnsmasq will take over
if DHCPv6 compiled in. The existing DHCPv6 and RA UCI
are translated into dnsmasq.conf. The changes focus on
'--dhcp-range', '--dhcp-host', and '--dhcp-options'.
DHCP host ID is least 16 bits [::1000-::FFFF], but
leaves low range for typical infrastructure assignments.
dnsmasq accepts DHCPv6 options in the tranditional
'--dhcp-option' put they must be prefixed 'option6:'.
dnsmasq will also discover SLAAC DNS entries from DHCPv4
clients MAC, and confirm with a ping at least renew.
Long term TODO include improving use of dnsmasq relay
options for DHCPv4 and DHCPv6 in parallel. It would also
be possible to preconfigure DHCP-PD in host-with-options
records for fixed infrastructure.
Signed-off-by: Eric Luehrsen <ericluehrsen@hotmail.com>
[Jo-Philipp Wich: emit proper IPv6 hostid format in dhcp-host directive]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
ref commit 612e2276b4
ref commit ec63e3bf13
'option add_local_hostname' scripted implementation statically assigns
this host in auto generated host file at init. If IFUP or other signals
do not occur, then address changes are not tracked. The script doesn't
apply all the addresses at an interface. This may make logs obscure.
The script only puts the bare host name (maybe not FQDN) in host file,
but if '--exapandhosts' is enabled, then /etc/hosts entries will be
suffixed, and "127.0.0.1 localhost" becomes "localhost.lan".
dnsmasq provides an option to perform this function, but it is rather
greedy. '--interface-name=<name>,<iface>' will assign the name to all
IP on the specified interface (except link local). This is a useful
feature, but some setups depend on the original restrictive behavior.
'option add_local_fqdn' is added to enhance the feature set, but
if not entered or empty string, then it will default to original
option and behavior. This new option has a few settings. At each
increased setting the most detailed name becomes the PTR record:
0 - same as add_local_hostname 0 or disabled
1 - same as add_local_hostname 1
2 - assigns the bare host name to all IP w/ --dnsmasq-interface
3 - assigns the FQDN and host to all IP w/ --dnsmasq-interface
4 - assigns <iface>.<host>.<domain> and above w/ --dnsmasq-nterface
'option add_wan_fqdn' is added to run the same procedure on
inferred WAN intefaces. If an interface has 'config dhcp' and
'option ignore 1' set, then it is considered WAN. The original
option would only run on DHCP serving interfaces.
Signed-off-by: Eric Luehrsen <ericluehrsen@hotmail.com>
This will allow starting hostapd with the new -s parameter and finally
read all (error) messages from the syslog.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It wasn't possible to read hostapd wpa_printf messages unless running
hostapd manually. It was because hostapd was printing them using vprintf
and not directly to the syslog.
We were trying to workaround this problem by redirecting STDIN_FILENO
and STDOUT_FILENO but it was working only for the initialization phase.
As soon as hostapd did os_daemonize our solution stopped working.
Please note despite the subject this change doesn't affect debug level
messages only but just everything printed by hostapd with wpa_printf
including MSG_ERROR-s. This makes it even more important as reading
error messages can be quite useful for debugging.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Updates to openvpn.init were included in early OpenVPN 2.4 patch
series, but got lost along the way and were never merged.
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
When relying on x.509 certs for auth and / or encryption of traffic you can't
use package openvpn-nossl.
Just have your package depend on openvpn-crypto to have SSL-encryption and
X.509-support enabled in OpenVPN. If encryption / X.509 is not a must, use
virtual packge openvpn, which is provided by all OpenVPN-variants.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
ap_setup_locked is named wps_ap_setup_locked in uci for consistency with other
wps related uci options.
Signed-off-by: Steven Honson <steven@honson.id.au>
The hostapd_append_wpa_key_mgmt() procedure uses the possibly uninitialized
$ieee80211r and $ieee80211w variables in a numerical comparisation, leading
to stray "netifd: radio0 (0000): sh: out of range" errors in logread when
WPA-PSK security is enabled.
Ensure that those variables are substituted with a default value in order to
avoid emitting this (harmless) shell error.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add PROVIDES:=openvpn to the default recipe in order to let all build variants
provide a virtual openvpn package.
The advantage of this approach is that downstream packages can depend on just
"openvpn" without having to require a specific flavor.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Use ubus process signalling instead of 'kill pidof dnsmasq' for
SIGHUP signalling to dnsmasq when ntp says time is valid.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
This causes problem when a FQDN is configured in /etc/config/system. The
domain name will appear twice in reverse DNS.
Next to that, there seems to be a bug in dnsmasq. From the manual page:
--interface-name=<name>,<interface>[/4|/6]
Return a DNS record associating the name with the primary address
on the given interface. This flag specifies an A or AAAA record for the
given name in the same way as an /etc/hosts line, except that the address
is not constant, but taken from the given interface. The interface may be
followed by "/4" or "/6" to specify that only IPv4 or IPv6 addresses
of the interface should be used. If the interface is down, not configured
or non-existent, an empty record is returned. The matching PTR record is
also created, mapping the interface address to the name. More than one name
may be associated with an interface address by repeating the flag; in that
case the first instance is used for the reverse address-to-name mapping.
It does not just create an A/AAAA record for the primary address, it creates
one for all addresses. And what is worse, it seems to actually resolve to the
non-primary address first. This is quite annoying when you use floating IP
addresses (e.g. VRRP), because when the floating IP is on the other device,
SSH failes due to incorrect entry in the known hosts file.
I know that this is not a common setup, but it would be nice if there was an
option to restore the previous behaviour, rather than just forcing this new
feature on everybody.
Reported-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
wpa_supplicant allows only SAE as the key management
type for mesh mode. The recent key_mgmt rework unconditionally
added WPA-PSK - this breaks interface bringup and wpa_s
throws this error message:
Line 10: key_mgmt for mesh network should be open or SAE
Line 10: failed to parse network block.
Failed to read or parse configuration '/var/run/wpa_supplicant-wlan0.conf
Fix this by making sure that only SAE is used for mesh.
Signed-off-by: Sujith Manoharan <m.sujith@gmail.com>
Enabling this makes it possible to query LLDP neighbors via SNMP.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Jo-Philipp Wich <jo@mein.io>
ef3c563 dhcpv6-ia: filter out prefixes having invalid length
16cd87e dhcpv6-ia: fix dereference after freeing assignment
d6b0c99 dhcpv6-ia: log only IPv6 addresses which are effectively
assigned to a DHCPv6 client
08a9367 config: respect ignore uci option
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
'add_local_hostname' previous implementation may drop some addresses.
Soft addition of IP6 addresses may not cause a reload or restart event.
dnsmasq '--interface-name' robustly applies DNS to all addresses per
interface (except fe80::/10).
Change UCI 'add_local_hostname' to expand during each interface assignement
during add_dhcp().
Assign '<iface>.<host>.<domain>' as true name (reflexive A, AAAA, and PTR).
Assign '<host>.<domain>' and '<host>' as convinience aliases (no PTR, not
technically CNAME).
This is accomplished with the '--interface-name' order, first is PTR.
We could also assign each <ip4/6>.<iface>.<host>.<domain> to the respective
dual stack on the interface.
That seemed excessive so it was skipped (/4 or /6 suffix to the interface).
Add UCI 'add_wan_hostname' similar to 'add_local_hostname' function for
external WAN.
WAN IP4 are less often named by the ISP and rarely WAN IP6 due to complexity.
For logs, LuCI connection graph, and other uses assigning a WAN name is desired.
'add_local_hostname' only applies with DHCP and 'add_wam_hostname' only applies
without DHCP. Common residential users will want to set both options TRUE.
Businesses will probably have global DNS, static IP, and 'add_wan_hostname' FALSE.
Signed-off-by: Eric Luehrsen <ericluehrsen@hotmail.com>
Add DHCPv6 matching by DHCP Unique Identifier (RFC-3315) in addition to
existing MAC-address (RFC-6939). The latter is not widely supported yet.
Signed-off-by: Arjen de Korte <build+lede@de-korte.org>
Enable support for stronger SHA256-based algorithms in hostapd and
wpa_supplicant when using WPA-EAP or WPA-PSK with 802.11w enabled.
We cannot unconditionally enable it, as it requires hostapd to be
compiled with 802.11w support, which is disabled in the -mini variants.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Sebastian Kemper <sebastian_ml@gmx.net>
Now that wpa_key_mgmt handling for hostapd and wpa_supplicant are
consistent, we can move parts of it to a dedicated function.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Sebastian Kemper <sebastian_ml@gmx.net>
Rework wpa_key_mgmt handling for wpa_supplicant to be consistent with
how it is done for hostapd.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Sebastian Kemper <sebastian_ml@gmx.net>
add possibility to set the facility to which dnsmasq will send syslog entries, i.e. set it to '/dev/null' to mute dnsmasq output at all.
Signed-off-by: Dirk Brenken dev@brenken.org
Before the rewrite, uhttpd-mod-tls used to contain a tls plugin.
Afterwards it was left in for compatibility reasons, but given how much
has changed, and that we're about to change the default SSL
implementation again, it's better to just drop this now
Signed-off-by: Felix Fietkau <nbd@nbd.name>
OpenVPN 2.4 builds with mbedTLS 2.x, rename openvpn-polarssl
variant to openvpn-mbedtls.
Some feature highlights:
* Data channel cipher negotiation
* AEAD cipher support for data channel encryption (currently only
* AES-GCM)
* ECDH key exchange for control channel
* LZ4 compression support
See https://github.com/OpenVPN/openvpn/blob/master/Changes.rst
for additional change notes.
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
Let dnsmasq reread the leasefile by using procd_send_signal
which triggers procd to send SIGHUP kill signal by default
if signal is not specified
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Update to latest upstream HEAD:
- Refreshed all
- Delete patches and parts which made it upstream
Compile tested Full & Mini configs
Run-tested Mini config
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [another update, remove broken patch]
The build system only accepts Package/<name>/description and since the
typoed version virtually has the same content as the TITLE field, remove
them altogether
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
The SIGHUP also got sent to the reload script making it bail out
with an error
Revert "dnsmasq: reload config if host name is modified"
This reverts commit 854459a2f9.
Reported-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
The sha256sum was not updated in the last commit.
Fixes: a7c231027 [odhcpd: Fix dnsmasq re-reading hostfile]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Harmonise handling of DEFAULT_PATH by removing the patch introducing #ifndef
guards around the path, and only using one means to set the path in the
makefile.
Signed-off-by: Dario Ernst <Dario.Ernst@riverbed.com>
Depending on the dhcp uci config pidof dnsmasq can return
multiple pids. Fix re-reading of the hostfile by dnsmasq in
such case by sending SIGHUP signal to each of the returned
pids.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Let dnsmasq read all hosts files in /tmp/hosts directory by specifying
/tmp/hosts as argument of --addn-host
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
OpenVPN requires arguments to --push to be enclosed in double quotes.
One set of quotes is stripped when the UCI config is parsed.
Change append_params() of openvpn.init to enclose push parameters in
double quotes.
Unquoted push parameters do not cause errors in OpenVPN 2.3,
but OpenVPN 2.4 fails to start with unquoted push parameters.
Fixes: FS#290.
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
Correct splitting the 32-bit 'hostid' value to two 16-bit hexadecimal
values. Previously, the lower 16-bit value was truncated to an 8-bit
value, which would result in hostid values 100 and 200 both to be set
to [::0:0] instead of [::0:100] and [::0:200] respectively.
Signed-off-by: Arjen de Korte <build+lede@de-korte.org>
If the hostname in /etc/config/system is modified the dnsmasq will not
reread the update host file under /tmp/hosts/dhcp.$cfg.
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
odhcpd daemon has hitless config reload support by means of the
sighup signal; add reload_service function which uses sighup
signal to reload the config
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Adds the mac address of the DNS requestor to DNS queries which
are forwarded upstream and can be used to do filtering by the
upstream servers. This only works if the requestor is on the
same subnet as the dnsmasq server
The addmac parameter can hold the following values:
0 : mac address is not added
1 : mac address is added in binary format
base64 : mac address is added base64 encoded
text: : mac address is added in human readable format
as hex and colons
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Ensure that selecting the wpa-supplicant-mesh package actually packages the
wpa_supplicant binary with SAE support and add missing dependency on OpenSSL.
Signed-off-by: Alexis Green <alexis@cessp.it>
[Jo-Philipp Wich: slightly reword commit message for clarity]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
We add an 'httpauth' section type that contains the options:
prefix: What virtual or real URL is being protected
username: The username for the Basic Auth dialogue
password: Hashed (crypt()) or plaintext password for the Basic Auth dialogue
httpauth section names are given included as list
items to the instances to which they are to be applied.
Further any existing httpd.conf file (really whatever
is configured in the instance, but default of
/etc/httpd.conf) is appended to the per-instance httpd.conf
Signed-off-by: Daniel Dickinson <lede@cshore.thecshore.com>
During reload, we could send invalid information to the other
side and confuse it.
That's why, during reload we'll pause execution, do the reconfig
and resume + update when reload is done.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
The problem is that interfaces are specified at start as
command line arguments, making them unchange-able via reload.
That means, we have to move (since lldpd allows this) the
interfaces-match-pattern option to be in a config file and reload
the configuration.
It's either that, or do a 'restart'.
Since we're generating the lldpd.conf file, we'll have to
move the 'sysconfdir' of lldpd to /tmp, where the files will
get written ; this will prevent any unncessary flash writes.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Adds support in uci for configuring multiple dnsmasq instances via
multiple dnsmasq sections.
The uci sections host, boot, mac, tag, vendorclass, userclass,
circuitid, ... will refer to a dnsmasq instance via the instance
parameter defined in the section; if the instance parameter is
not specified backwards compatibility is preserved.
Start/Stopping a dnsmasq instance can be achieved by passing the
dnsmasq instance name as argument to start/stop via the init script.
Multiple dnsmasq instances is usefull in scenarios where you want to
bind a dnsmasq instance to an interface in order to isolate networks.
This patch is a rework of a multiple dnsmasq instance patch by Daniel Dickinson
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Add a partially random O= item to the certificate subject in order
to make the automatically generated certificates' subjects unique.
Firefox has problems when several self-signed certificates
with CA:true attribute and identical subjects have been
seen (and stored) by the browser. Reference to upstream bugs:
https://bugzilla.mozilla.org/show_bug.cgi?id=1147544https://bugzilla.mozilla.org/show_bug.cgi?id=1056341https://bugzilla.redhat.com/show_bug.cgi?id=1204670#c34
Certificates created by the OpenSSL one-liner fall into that category.
Avoid identical certificate subjects by including a new 'O=' item
with CommonName + a random part (8 chars). Example:
/CN=LEDE/O=LEDEb986be0b/L=Unknown/ST=Somewhere/C=ZZ
That ensures that the browser properly sees the accumulating
certificates as separate items and does not spend time
trying to form a trust chain from them.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Prefer the old default 'px5g' for certificate creation
as Firefox seems to dislike OpenSSL-created certs.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
The special prefix of "/" should match any url by definition but the final
assertion which ensures that the matched prefix ends in '\0' or '/' is causing
matches against the "/" prefix to fail.
Update to current HEAD in order to fix this particular case.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This more of a demo for the previous commit that comes with
this one, where I added support for copying source from 'src' to
the build dir(s).
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Adds per-host leasetime support
Various bugfixes :
-Prioritize ifname resolving via ubus
-Free interface if ifindex cannot be resolved
-...
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [update mirror sha256]
* Change git packages to xz
* Update mirror checksums in packages where they are used
* Change a few source tarballs to xz if available upstream
* Remove unused lines in packages we're touching, requested by jow- and blogic
* We're relying more on xz-utils so add official mirror as primary source, master site as secondary.
* Add SHA256 checksums to multiple git tarball packages
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Now that the uhttpd init script can generate certificates using openssl as
well, update the section name and related comment to be more generic.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Support the usage of the OpenSSL command-line tool for generating
the SSL certificate for uhttpd. Traditionally 'px5g' based on
PolarSSL (or mbedTLS in LEDE), has been used for the creation.
uhttpd init script is enhanced by adding detection of an installed
openssl command-line binary (provided by 'openssl-util' package),
and if found, the tool is used for certificate generation.
Note: After this patch the script prefers to use the OpenSSL tool
if both it and px5g are installed.
This enables creating a truly OpenSSL-only version of LuCI
without dependency to PolarSSL/mbedTLS based px5g.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Configurations without shadow passwords have been broken since the removal
of telnet: as the default entry in /etc/passwd is not empty (but rather
unset), there will be no way to log onto such a system by default. As
disabling shadow passwords is not useful anyways, remove this configuration
option.
The config symbol is kept (for a while), as packages from feeds depend on
it.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Match sections allow to set a tag specified by the option networkid if the client
sends an option and optionally the option value specified by the match option.
The force option will convert the dhcp-option to force-dhcp-option if set to 1 in
the dnsmasq config if options are specified in the dhcp_option option.
config match
option networkid tag
option match 12,myhost
option force 1
list dhcp_option '3,192.168.1.1'
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Permit users of the full variant to disable the NO_ID *.bind pseudo
domain masking.
Defaulted 'on' in all variants.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
As security precaution and to limit the attack surface based on
the version reported by tools like nmap mask out the dropbear
version so the version is not visible anymore by snooping on the
wire. Version is still visible by 'dropbear -V'
Based on a patch by Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [remove trailing _]
Don't expose dnsmasq version & other data to clients via the *.bind
pseudo domain. This uses a new 'NO_ID' compile time option which has been
discussed and submitted upstream.
This is an alternate to replacing version with 'unknown' which affects
the version reported to syslog and 'dnsmasq --version'
Run time tested with & without NO_ID on Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Regression introduced by 3481d0d dnsmasq: run as dedicated UID/GID
dnsmasq is unable to remove its own pidfile as /var/run/dnsmasq is owned
by root and now dnsmasq runs as dnsmasq:dnsmasq. Change directory
ownership to match.
dnsmasq initially starts as root, creates the pidfile, then drops to
requested non-root user. Until this fix dnsmasq had insufficient
privilege to remove its own pidfile.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
PPP daemon can be put into persist mode meaning the
daemon will not exit after a connection gets terminated
but will instead try to reopen the connection.
The re-initiation after the link has been terminated
can be controlled via holdoff; this is helpfull in
scenarios where a BRAS is in denial of service mode
due to link setup requests after a BRAS has gone down
Following uci parameters have been added :
persist (boolean) : Puts the ppp daemon in persist mode
maxfail (integer) : Number of consecutive fail attempts which
puts the PPP daemon in exit mode
holdoff (interget) : Specifies how many seconds to wait
before re-initiating link setup after it has been terminated
Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* Only parse interfaces that are up during init_config (as the
script depends on this to determine the proper IP/subnet range)
* Add reload interface triggers for samba-designated interfaces
* Force full service restart upon config change to ensure Samba
binds to new interfaces (sending HUP signal doesn't work)
* Rename "interface" variable to "samba_iface" and move into
global scope
Needed to fix Samba connectivity for clients connecting from a
different LAN subnet (e.g. pseudobridge configurations) due to the
'bind interfaces only' setting.
Signed-off-by: Conn O'Griofa <connogriofa@gmail.com>
