08719b1 mt76: use a per rx queue page fragment cache
4d2c565 mt76x2: reset HW before probe
f622975 mt76x2: fix CCK protection control frame rate
6780375 mt76x2: add frame protection support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Allow enabling/commenting/disabling each feed individually by using a
tristate config symbol.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
FEEDS_ENABLED and FEEDS_DISABLED are derived from FEEDS_AVAILABLE, not
FEEDS_INSTALLED.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
'In different versions of coreboot are different names of apu boardname.
No need to check boardname to load module.'
Signed-off-by: Lukáš Mrtvý <lukas.mrtvy@gmail.com>
Enables support for Dynack feature.
When a remote station is far away, we need to compensate for the distance
by allowing more time for an ACK to arrive back before issueing a retransmission.
Currently, it needs to be set fixed to indicate the maximum distance the remote
station will ever be.
While this mostly works for static antennae, it introduces 2 issues:
- If the actual distance is less, speed is reduced due to a lot of wates wait-time
- If the distance becomes greater, retries start to occur and comms can get lost.
Allowing to set it dynamically using dynack ensures the best possible tradeoff
between speed vs distance.
This feature is currently only supported in ath9k.
it is also disabled by default.
Enabling it can be done in 2 ways:
- issue cmd: iw phy0 set distance auto
- sending the NL80211_ATTR_WIPHY_DYN_ACK flag to mac80211 driver using netlink
Disabling it can be done by providing a valid fixed value.
To give an idea of a practical example:
In my usecase, we have mesh wifi device installed on ships/platforms.
Currently, the coverage class is set at 12000m fixed.
When a vessel moved closer (ex. 1500m), the measured link capacity was a lot
lower compared to setting the coverage class fixed to 1500m
Dynack completely solved this, nearly providing double the bandwidth at closer range
compared to the fixed setting of 12000m being used.
Also when a vessel sailed to a distance greater than the fixed setting,
communication was lost as the ACK's never arrived within the max allowed timeframe.
Actual distance: 6010m
iperf 60s run avg
Fixed 12150m: 31 Mbit/s
Dynack: 58 Mbit/s
Fixed 6300m: 51 Mbit/s
Dynack: 59 Mbit/s
Fixed 3000m: 13 Mbit/s (lots of retries)
Dynack: 58 Mbit/s
Actual distance: 1504m
iperf 60s run avg
Fixed 12150m: 31 Mbit/s
Dynack: 86 Mbit/s
Fixed 6300m: 55 Mbit/s
Dynack: 87 Mbit/s
Fixed 3000m: 67 Mbit/s
Dynack: 87 Mbit/s
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* device: print daddr not saddr in missing peer error
* receive: style
Debug messages now make sense again.
* wg-quick: android: support excluding applications
Android now supports excluding certain apps (uids) from the tunnel.
* selftest: ratelimiter: improve chance of success via retry
* qemu: bump default kernel version
* qemu: decide debug kernel based on KERNEL_VERSION
Some improvements to our testing infrastructure.
* receive: use NAPI on the receive path
This is a big change that should both improve preemption latency (by not
disabling it unconditionally) and vastly improve rx performance on most
systems by using NAPI. The main purpose of this snapshot is to test out this
technique.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Update to the latest version of iproute2; see https://lwn.net/Articles/756991/
for a full overview of the changes in 4.17.
Remove upstream patch 002-json_print-fix-hidden-64-bit-type-promotion.
Backport upstream patch 001-rdma-sync-some-IP-headers-with-glibc fixing
rdma compile issue.
At the same time re-organize patch numbering so the OpenWRT specific
patches start at 100.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
345bba0 dhcpv4: improve error checking in handle_dhcpv4()
c0f6390 odhcpd: Check if open the ioctl socket failed
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* change mx6qsabresd to mx6qsabres to match defconfig name
* merge wanboard profiles since there is only one defconfig for the target device
* move wanboard options from wandboard.h to defconfig
* remove legacy patches
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Most of the implementations behind cfg80211_get_station will not initialize
sinfo to zero before manipulating it. For example, the member "filled",
which indicates the filled in parts of this struct, is often only modified
by enabling certain bits in the bitfield while keeping the remaining bits
in their original state. A caller without a preinitialized sinfo.filled can
then no longer decide which parts of sinfo were filled in by
cfg80211_get_station (or actually the underlying implementations).
cfg80211_get_station must therefore take care that sinfo is initialized to
zero. Otherwise, the caller may tries to read information which was not
filled in and which must therefore also be considered uninitialized. In
batadv_v_elp_get_throughput's case, an invalid "random" expected throughput
may be stored for this neighbor and thus the B.A.T.M.A.N V algorithm may
switch to non-optimal neighbors for certain destinations.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Board Data File (BDF) is loaded upon driver boot-up procedure. The right
board data file is identified on QCA4019 using bus, bmi-chip-id and
bmi-board-id.
The problem, however, can occur when the (default) board data file cannot
fulfill the vendor requirements and it is necessary to use a different
board data file.
This problem was solved for SMBIOS by adding a special SMBIOS type 0xF8.
Something similar has to be provided for systems without SMBIOS but with
device trees. No solution was specified by QCA and therefore a new one has
to be found for ath10k.
The device tree requires addition strings to define the variant name
wifi@a000000 {
status = "okay";
qcom,ath10k-calibration-variant = "RT-AC58U";
};
wifi@a800000 {
status = "okay";
qcom,ath10k-calibration-variant = "RT-AC58U";
};
This would create the boarddata identifiers for the board-2.bin search
* bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=RT-AC58U
* bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=RT-AC58U
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
With deterministic ECDSA the value k needed for the ECDSA signature is
not randomly generated any more, but generated from a hash over the
private key and the message to sign. If the value k used in a ECDSA
signature or the relationship between the two values k used in two
different ECDSA signatures over the same content is know to an attacker
he can derive the private key pretty easily. Using deterministic ECDSA
as defined in the RFC6979 removes this problem by deriving the value k
deterministically from the private key and the content which gets
signed.
The resulting signature is still compatible to signatures generated not
deterministic.
This increases the size of the ipk on mips 24Kc by about 2 KByte.
old:
166.240 libmbedtls_2.11.0-1_mips_24kc.ipk
new:
167.811 libmbedtls_2.11.0-1_mips_24kc.ipk
This does not change the ECDSA performance in a measurable way.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Disable MBEDTLS_SHA256_SMALLER implementation, not enabled by default in
upstream and reduces performance by quite a bit.
Source: include/mbedtls/config.h
Enable an implementation of SHA-256 that has lower ROM footprint but also
lower performance.
The default implementation is meant to be a reasonnable compromise between
performance and size. This version optimizes more aggressively for size at
the expense of performance. Eg on Cortex-M4 it reduces the size of
mbedtls_sha256_process() from ~2KB to ~0.5KB for a performance hit of
about 30%.
The size of mbedtls increased a little bit:
ipkg for mips_24kc before:
164.382 Bytes
ipkg for mips_24kc after:
166.240 Bytes
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Update mbed TLS to 2.11.0
Disable OFB block mode and XTS block cipher mode, added in 2.11.0.
The soVersion of mbedtls changed, bump PKG_RELEASE for packages that use mbedTLS
This is to avoid having a mismatch between packages when upgrading.
The size of mbedtls increased a little bit:
ipkg for mips_24kc before:
163.846 Bytes
ipkg for mips_24kc after:
164.382 Bytes
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
OpenSSL defaults X509_CERT_FILE to /etc/ssl/cert.pem. This change is
needed for wget-ssl and possibly others to work seamlessly with fresh
ca-bundle installation
Fixesopenwrt/packages#6152
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* New microcode update packages from AMD upstream:
+ New Microcodes:
sig 0x00800f12, patch id 0x08001227, 2018-02-09
+ Updated Microcodes:
sig 0x00600f12, patch id 0x0600063e, 2018-02-07
sig 0x00600f20, patch id 0x06000852, 2018-02-06
* Adds Spectre v2 (CVE-2017-5715) microcode-based mitigation support,
plus other unspecified fixes/updates.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Fixes a potential infinite loop bug when in unlimited (ie not using
built in shaper) mode.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
- Removed hacks to use standalone argp as upstream now detects it nicely.
- As we are already installing files, use files from PKG_INSTALL_DIR and
not PKG_BUILD_DIR
- Only changes Makefile.am as PKG_FIXUP:=autoreconf is in use
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Refresh patches and backport upstream to current HEAD:
a997ca0 Fix sometimes missing DNSSEC RRs when DNSSEC validation not enabled.
51e4eee Fix address-dependent domains for IPv6.
05ff659 Fix stupid infinite loop introduced by preceding commit.
db0f488 Handle some corner cases in RA contructed interfaces with addresses changing interface.
7dcca6c Warn about the impact of cache-size on performance.
090856c Allow zone transfer in authoritative mode whenever auth-peer is specified.
cc5cc8f Sane error message when pcap file header is wrong.
c488b68 Handle standard and contructed dhcp-ranges on the same interface.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This bumps to the latest & possibly greatest cake, sadly it's still
inedible but from an SQM point of view quite tasty :-)
Main tweaks since previous bump, improved ack_filter, some extra stats,
support for 64bit netlink parameters (higher rates/byte counters)
0520a6c Fix NAT option handling
8da93e1 Make sure we always call qdisc_watchdog_init() in cake_init()
f65daf6 Fix mismatched parenthesis
51d4ab3 Change flag handling to be safe even when mixing with non-eligible ACKs
f2ea091 ack_filter: protect DCTCP with stricter filtering of ECE marks
28b4560 ACK filter: Handle wrapping sequence numbers and DSACKs
73f62d9 Use the right PAD attribute for options
5969c14 Use 32 for tin backlog
e289f31 Move all the u64 netlink attributes together
36180a0 Check ACK seqno before parsing SACKs
91bbc01 Merge branch 'mine' into cobalt
58c55ec Rework SACK check to compare the ranges of two SACKs
9a5d593 ack_filter: Add proper handling of SACKs
eca95d4 ack_filter: short-circuit TCP flag check
d50a246 compat: backport some ktime functions
7b7ad11 compat: define tcpopt_fastopen for pre-4.1 kernels
ca54cdb Fix ktime compare
9d7dcc0 ack filter: Parse TCP options and only drop safe ones
b119882 Return EOPNOTSUPP on NAT option if conntrack is not available
842d7f0 Don't try to pad stats with tin_stats padding
bd46dc2 Use 64-bit divide helper
8e41bf0 Make sure we never drop SACKs when filtering ACKs
66e5d60 Avoid comparing ktime_t to scalar values
7fab017 Actually commit the ktime_t changes
fca6d13 Switch to ktime_t and get rid of cobalt.h
6f7e5af Can't use do_div with 64-bit divisors
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Bump iproute2/tc support of cake.
Add support for cake's change to u64 attribute passing for certain
attributes (rate & byte counts)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
48cff25 build: drop install -o/-g root
53d7e7a extensions: ebt_string: take action if snprintf discards data
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This was causing issues recently as samba36 is not API compatible with the
libtdb in the packages repo. It shouldn't be using it anyway. Nor tevent.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The return value of the function isn't used anywhere.
Fixes missing return value, CID 1329717.
Found-by: Coverity
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
