As usual these patches were extracted and rebased from the raspberry pi repo:
https://github.com/raspberrypi/linux/tree/rpi-4.4.y
Also adds support for Raspberry Pi Compute Module 3 (untested).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
commit a2386c384d requires the
module to be static in the kernel.
So lets actually add support for it inside the kernel config.
Tested on Ventana
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Now that all seama images are using the new build code this seama recipe
used with the old build code can be dropped.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Set the blocksize for devices having only 4MB of flash for ramips
devices already using the new image build code.
Informations about the used flash chip are gathered from the OpenWrt
wiki, wikidevi, forums, OEM bootlogs or the compatible property in the
device tree source file.
The en25q32b from the AirLive Air3GII does not have 4k support in the
kernel.
For the following boards no information about the used flash chip could
be found and a 64k blocksize is assumed:
- Ralink V11ST-FE
- Ralink AP-RT3052-V22RW-2X2
- MediaTek MT7628 EVB
- MediaTek MT7621 EVB
- UPVEL UR-326N4G
- Buffalo WZR-AGL300NH
Signed-off-by: Mathias Kresin <dev@kresin.me>
Some devices (e.g. Tenda AC9 based on BCM47189B0) have BCM53125 with
port 5 connected to the second Ethernet interface on the SoC. In such
case there is no PHY and we need to force link manually.
This assumes port 5 can be marked as enabled for such devices. It's not
implemented yet unfortunately.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The insertion or removal of the sd-card cannot be detected
by the hardware itself. This is by design. To workaround this,
for the WNDR4700 unload/load the dwc2 module in case the
the special SD CARD GPIO line is low/high.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
First two patches weren't marked for stable but are dependencies for
laters ones. The rest of patches was marked for stable but most likely
will be backported to 4.5+ only so we need to get them on our own.
An important fix is eea2fb4851e9d ("ovl: proper cleanup of workdir") as
it allows mounting overlayfs with dirty workdir, e.g. after power cut.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
If the toolchain is packaged for later use as external toolchain, the resulting
tarball is created in $BIN_DIR. But without building all packages first that
directory isn't created, hence 'make target/toolchain/compile' fails when
trying to create the toolchain tarball with error "Cannot open: No such file or
directory".
To fix that the $BIN_DIR is created before using it.
Signed-off-by: Micha Lenk <micha@lenk.info>
Russell Senior reported an issue with the MR24 initramfs kernels:
> ## Booting kernel from Legacy Image at 00c10000 ...
> Image Name: POWERPC LEDE Linux-4.4.19
> Created: 2016-08-31 11:57:05 UTC
> Image Type: PowerPC Linux Kernel Image (gzip compressed)
> Data Size: 2155723 Bytes = 2.1 MiB
> Load Address: 00000000
> Entry Point: 00000000
> Verifying Checksum ... OK
>Wrong Ramdisk Image Format
>Ramdisk image is corrupt or invalid
For the MR24, the kernel is uploaded to 0x10000. The ramdisk starts
at 0x200000. This leaves the kernel with just 0x1f0000 bytes = 1984kb.
This patch adds a size check so the image creation script will abort
instead of producing a unbootable initramfs image. A separate patch
"apm821xx: Fix initramfs image for the Meraki MR24" which fixed the
reported issue was submitted earlier.
Cc: Russell Senior <russell@personaltelco.net>
Cc: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
When gzip is used, our kernel is too large and this causes the ramdisk
to be at the wrong offset. Fix by moving to lzma.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Add a patch to backport 5185c91385d73cdf79836eb8548e4726e43ae831
from Linux 4.8 adding USB2380 support to the NET2280 driver and
create an OpenWrt menu option to select it as a module.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Gateworks Ventana GW553x is a single-board computer based on the NXP
IMX6 SoC with the following features:
* IMX6 DualLite Soc (supports IMX6S,IMX6DL,IMX6Q)
* small form factor (35x70mm)
* 512MB DDR3 DRAM (2x32bit) (options up to 2GB)
* 256MB NAND flash (4GB option)
* Gateworks System Controller:
- hardware watchdog
- hardware monitor
- pushbutton controller
- EEPROM storage
- power control
* JTAG programmable
* 1x miniPCI socket (with PCIe, USB, SIM)
* 1x microSD socket
* 1x SIM socket
* Inertial Module (LSM9DS1 9DOF: 3x acc, 3x rate, 3x mag)
* analog CVBS video in
* GPS (optional uBlox EVA-M8M)
* Application headers:
- 2x TTL UART (TX/RX)
- 4x TTL GPIO (3x configurable as PWM)
- 3x CVBS Analog video input (1x decoder with 3x selectable inputs)
* Front panel connectors:
* micro-HDMI audio/video out
- 1x user programmable LED
- 1x configurable user pushbutton
- 1x USB OTG
See http://www.gateworks.com for more info
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Added gen_mvebu_sdcard_img.sh to facilitate creating an fixed-size sdcard image,
adding the bootloader and populating it with actual data.
Added the required rules for creating a 4GB sdcard image according to this layout:
p0: boot (fat32)
p1: rootfs (squashfs)
p2: rootfs_data (ext4)
This should be generic to any mvebu boards that can boot from block storage.
Added the new sdcard image to the Clearfog image profile.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup]
The u-boot variant for the clearfog is provided by the uboot-mvebu-clearfog,
and not by the generic uboot-mvebu packae.
Make sure the clearfog variant is selected when building for it.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This triggers HAS_FPU=y, and unsets CONFIG_SOFT_FLOAT.
Considering all mvebu boards have an fpu, this is the desirable behaviour.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
microSD is the primary boot media for the Clearfog Pro board, and should
work unconditionally.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup]
Add Support for the ESMT_F25L32QA and ESMT_F25L64QA.
These are 4MB and 8MB SPI NOR Chips from Elite Semiconductor Memory Technology
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
TP-Link has started providing US- and EU-specific stock firmwares that only
allow upgrading to firmwares with the same region code. Provide factory
images for both these regions.
To avoid confusing users outside these regions, we still provide a
"universal" factory.bin without a region code, although flashing either of
the US and EU images would work as well.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Historically on ARC we started from initramfs-based images because:
a) It was much easier to debug especially when toolchain and other
components were changing quite dynamically
b) It was our usual approach for embedded Linux
But now with ARC port of Lede/OpenWRT getting more stable and mature
we're ready for more real-life scenarios with FS permanently stored
on SD-card. This essentially benefits from ability to setup devices
that survive reboots with all settings and extra packages kept in place.
Still we keep an ability to build images with initramfs.
This allows us to use storage-less simulators for testing still.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: John Crispin <john@phrozen.org>
Cc: Jo-Philipp Wich <jo@mein.io>
If we want to boot from SD-card we need to have corresponding
drivers already built-in so there's no point in having these
modules.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Now when we're switching to FS on SD-card it's necessary to have
full stack of MMC block & FC drivers built-in otherwise kernel won't
be able to mount FS with needed modules.
Also we enable parsing of input parameters passed to the kernel by
U-Boot. Otherwise kernel won't know where to look for command line and
what's worse device tree blob (we had to disable this by default for
cases when kernel is loaded by JTAG and core registers may have
undefined state lading to kernel going bonkers).
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
As support of ARC 770 in OpenWRT/Lede matures we don't need
debug-only output binaries any longer, so purging vmlinux for
AXS10x boards.
As for uImage for nSIM it makes completely no sense because there's no
way to run U-Boot on nSIM.
So we remove add_arcYYY_XXX scripts making code more compact and
cleaner.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Drivers have been modified to use it and new ones have to be written
this way, so we need it for backporting code.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
With 12fe4b5798 I switched the ath5k
eeprom extraction to an alternate code path. Unfortunately this code
seams to be broken since ages and broke the ath5k EEPROM extraction.
Reported-by: Mohammed Berdai <mohammed.berdai@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: John Crispin <john@phrozen.org>
DW GMAC on ARC SDP boards doesn't enter promiscuous mode if
Ethernet PHY haven't got established link. Good examples are
auto-negotiation in progress or disconnected cable.
We do see Linux kernel sets GMAC's MAC filter register
properly but GMAC's hardware doesn't accept new settings.
We believe it is a hardware issue, most probably problem of
integration of DW GMAC and PHY on the board.
As a work-around we completely disable frame filtering
in GMAC hardware (once and for good) which forces GMAC to enter
promiscuous mode with the first write to MAC filter register.
That gives us working bridge that consists of eth0 and wlan0
(USB Wi-Fi dongle). I.e. we finally have working "Dumb AP" setup made
of ARC AXS10x boards.
Given that hack is quite dirty (in loaded wired networks this will
effectively load CPU with junk packets even if user doesn't need promisc
mode) and there's no indication any other boards with DW GMAC suffer
from the same issue we're patching only kernel for ARC boards.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: John Crispin <john@phrozen.org>,
Cc: Felix Fietkau <nbd@nbd.name>
This allows referencing USB ports/devices that are always present in a
device. This applies to some internal devices, root hub ports and
internal USB hubs.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The R7800 is an IPQ8065, so rename its dts file to reflect that fact.
Also fold the R7500v2 dts addition into the existing 800-devicetree.patch.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
1004kc is just a SMP capable 34kc, and GCC treats 24kc and 34kc exactly
the same and will generate identical code, so there is no need to tune
to 1004kc instead of 24kc.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
GCC treats 24kc and 34kc exactly the same and will generate identical
code, so there is no need to tune to 34kc instead of 24kc.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
GCC treats 24kc and 34kc exactly the same and will generate identical
code, so there is no need to tune to 34kc instead of 24kc.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked broken.
Runtime-tested on ar71xx, octeon and x86/64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Point to correct devices when booting from msata or MMC
Changes fetched from Gateworks git
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[Jo-Philipp Wich: rebased to apply against current LEDE version]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Alexis Green <alexis@cessp.it>
[Jo-Philipp Wich: add missing DEVICE_TITLE, fix model name in commit title]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
