The CE image format used by OpenMesh can contain extra blocks which
are not used for flashing. Only the first three embedded images
(fwupgrade.cfg, kernel, rootfs) are required in this order to successfully
flash an image via sysupgrade. All extra embedded images should be ignored
for the available devices.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
The platform_check_image_openmesh function used break statements to signal
that the board name matched the image target. This worked because the
sysupgrade binary checked the image inside a loop. The break statement
stopped the loop and skipped any additional check.
Instead the check should be done without such sideeffects by simply
combining the board names and image targets. Only a mismatch should cause a
negative result for the caller and skipping of the additional checks.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Some OpenWrt based firmwares like Gluon expect that a sysupgrade image
exists when a device firmware can be updated via sysupgrade. This image
wasn't created until now because OpenMesh devices use the same image for
factory and sysupgrade flash. Copying the image from *factory.bin to
*sysupgrade.bin is therefore enough to make the sysupgrade functionality
visible.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Summary of changes:
* moved config-3.18 to config-4.4 and patches-3.18 to patches-4.4
* removed most of the first two patches, that seem to be upstream already
* changed deprecated/removed IRQF_DISABLED to zero following examples in upstream kernel patches
* added config line to disable device-tree to satisfy kernel configuration
* add new image generation code
Build tested and run tested on an Accton MR3201A.
Signed-off-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
Currently, for RT5350 and MT7628, esw is marked as compatible with
"ralink,rt3050-esw". While this is true, the switches within RT5350
and MT7628 actually support more functionality than the RT3050 switch.
One such example is per-VLAN untagging, which is an important feature.
RT3352 is another example of this, but it already has an additional
compatible property, which allows to differentiate it from RT3050.
This commit adds such more specific properties for RT5350 and MT7628
as well.
Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
The only difference between the VG3503J profiles is the version of the
gphy firmware that gets loaded. This can be handled perfect fine in one
device tree source file.
Signed-off-by: Mathias Kresin <dev@kresin.me>
According to the author, all SPI related configs are copy & paste
leftovers. Which makes sense since nothing is connected to the SPI bus
on this device.
The NOR SPL isn't required for this board, since the NOR is directly
memory mapped.
Allow to overwrite the env in ram while using brn variant. Do not set
the power GPIO pin twice.
Signed-off-by: Mathias Kresin <dev@kresin.me>
use:
- 00nn for u-boot patches
- 01nn for new boards
While doing the rework, the board definitions for the easy50712 and
easy80920 were moved to distinct board definitions patches.
Signed-off-by: Mathias Kresin <dev@kresin.me>
- disable all ethernet ports except port 0 on MPR-A2
Port 0 is the only ethernet port on this router, so disable all other PHYs in order to save power.
- don't use a VLAN for the single ethernet port of the MPR-A2
Like A5-V11, this router only has one ethernet port.
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Disable marvell,nand-keep-config property on WRT1900AC to allow the
flash driver to properly probe the chip
Signed-off-by: Felix Fietkau <nbd@nbd.name>
