Commit graph

535 commits

Author SHA1 Message Date
Christian Lamparter
82618062cf ipq40xx: add support for the ZyXEL NBG6617
This patch adds support for ZyXEL NBG6617

Hardware highlights:

SOC:    IPQ4018 / QCA Dakota
CPU:    Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:   256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz
NOR:    32 MiB Macronix MX25L25635F
ETH:    Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB:    1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1:  Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:  Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:  RESET Button, WIFI/Rfkill Togglebutton, WPS Button
LEDS:   Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS

Serial:
	WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
	The Serial setting is 115200-8-N-1. The 1x4 .1" header comes
	pre-soldered. Pinout:
	  1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX

first install / debricking / restore stock:
 0. Have a PC running a tftp-server @ 192.168.1.99/24
 1. connect the PC to any LAN-Ports
 2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file
    into the tftp-server root directory and rename it to just "ras.bin".
 3. power-cycle the router and hold down the the WPS button (for 30sek)
 4. Wait (for a long time - the serial console provides some progress
    reports. The u-boot says it best: "Please be patient".
 5. Once the power LED starts to flashes slowly and the USB + WPS LEDs
    flashes fast at the same time. You have to reboot the device and
    it should then come right up.

Installation via Web-UI:
 0. Connect a PC to the powered-on router. It will assign your PC a
    IP-address via DHCP
 1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234)
 2. Go to the "Expert Mode"
 3. Under "Maintenance", select "Firmware-Upgrade"
 4. Upload the OpenWRT factory image
 5. Wait for the Device to finish.
    It will reboot into OpenWRT without any additional actions needed.

To open the ZyXEL NBG6617:
 0. remove the four rubber feet glued on the backside
 1. remove the four philips screws and pry open the top cover
    (by applying force between the plastic top housing from the
    backside/lan-port side)

Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:

|   Hit any key to stop autoboot:  3

The user is then dropped to a locked shell.

|NBG6617> HELP
|ATEN    x[,y]     set BootExtension Debug Flag (y=password)
|ATSE    x         show the seed of password generator
|ATSH              dump manufacturer related data in ROM
|ATRT    [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO              boot up whole system
|ATUR    x         upgrade RAS image (filename)
|NBG6617>

In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!

First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.

|NBG6617> ATSE NBG6617
|012345678901

This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):

- tool.sh -
ror32() {
  echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -

|# bash ./tool.sh 012345678901
|
|ATEN 1,879C711

copy and paste the result into the shell to unlock zloader.

|NBG6617> ATEN 1,0046B0017430

If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.

|NBG6617> ATGU
|NBG6617#

Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-26 08:57:26 +02:00
Daniel Golle
ff0f3522b7 uboot-oxnas: fix typo accidentally committed during oxnas reboot
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-18 18:55:19 +02:00
Hauke Mehrtens
9a26a9e8b9 uboot-sunxi: update Orange Pi R1 and Zero Plus
The device tree files are now matching the kernel 4.17 and this will be
send also for integration into mainline U-Boot.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-06-18 07:10:20 +02:00
Hauke Mehrtens
f2135e7811 uboot-sunxi: update to version 2018.05
This patch 220-add-sunxi50i-nanopi-neo-plus2.patch was merged upstream.
The u-boot-sunxi-with-spl.bin is now also created for the ARM64 sunxi
boards by U-Boot itself, no need to do it manually any more.

This was tested on a H2+ Orange Pi R1 and a H5 Orange Pi Zero Plus.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-06-18 07:10:20 +02:00
Hauke Mehrtens
7afe1caf70 arm-trusted-firmware-sunxi: update to version from 2018-02-10
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-06-18 07:10:20 +02:00
David Bauer
e36f8b3f39 ar71xx: add support for OCEDO Koala
This commit adds support for the OCEDO Koala

SOC:	Qualcomm QCA9558 (Scorpion)
RAM:    128MB
FLASH:  16MiB
WLAN1:  QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2:  QCA9880 5 GHz 802.11nac 3x3
INPUT:  RESET button
LED:    Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
        Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi
 - 5 GHz WiFi
 - TFTP boot from ramdisk image
 - Installation via ramdisk image
 - OpenWRT sysupgrade
 - Buttons
 - LEDs

Installation seems to be possible only through booting an OpenWRT
ramdisk image.

Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.

Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.

Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.

Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with

 > fw_setenv bootcmd run bootcmd_1

Afterwards you can reboot the device.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-07 09:31:58 +02:00
Luis Araneda
8c8499f0ea uboot-zynq: update to 2017.03
Compile-tested: ZedBoard

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-06-07 09:00:49 +02:00
Daniel Golle
dcc34574ef oxnas: bring in new oxnas target
Reboot the oxnas target based on Linux 4.14 by rebasing our support on
top of the now-existing upstream kernel support.
This commit brings oxnas support to the level of v4.17 having upstream
drivers for Ethernet, Serial and NAND flash.
Botch up OpenWrt's local drivers for EHCI, SATA and PCIe based on the
new platform code and device-tree.
Re-introduce base-files from old oxnas target which works for now but
needs further clean-up towards generic board support.

Functional issues:
 * PCIe won't come up (hence no USB3 on Shuttle KD20)
 * I2C bus of Akitio myCloud device is likely not to work (missing
   debounce support in new pinctrl driver)

Code-style issues:
 * plla/pllb needs further cleanup -- currently their users or writing
   into the syscon regmap after acquireling the clk instead of using
   defined clk_*_*() functions to setup multipliers and dividors.
 * PCIe phy needs its own little driver.
 * SATA driver is a monster and should be split into an mfd having
   a raidctrl regmap, sata controller, sata ports and sata phy.

Tested on MitraStar STG-212 aka. Medion Akoya MD86xxx and Shuttle KD20.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-01 15:45:06 +02:00
Daniel Golle
d44b7b7d31 uboot-oxnas: fix build with newer GCC
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-01 15:45:06 +02:00
Jo-Philipp Wich
1289e00fff uboot-zynq: fix build on hosts lacking pkg-config
The uboot-mvebu package incorrectly used the host pkg-config for the tool
build parts, which broke the build on systems lacking pkg-config and only
worked by accident on those that have it installed.

Export the host-build specific environment variables for the uboot build
to redirect pkg-config invocations to our staged host build pkg-config in
buildroot.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-05-23 09:32:25 +02:00
Jo-Philipp Wich
208b984dda uboot-mxs: fix build on hosts lacking pkg-config
The uboot-mvebu package incorrectly used the host pkg-config for the tool
build parts, which broke the build on systems lacking pkg-config and only
worked by accident on those that have it installed.

Export the host-build specific environment variables for the uboot build
to redirect pkg-config invocations to our staged host build pkg-config in
buildroot.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-05-23 09:15:52 +02:00
Jo-Philipp Wich
01c2ce3c7d uboot-mvebu: fix build on hosts lacking pkg-config
The uboot-mvebu package incorrectly used the host pkg-config for the tool
build parts, which broke the build on systems lacking pkg-config and only
worked by accident on those that have it installed.

Export the host-build specific environment variables for the uboot build
to redirect pkg-config invocations to our staged host build pkg-config in
buildroot.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-05-23 09:05:55 +02:00
Michael Gray
bfbdeeb3de mvebu: add support for WRT32X (venom)
Linksys WRT32X (Venom) is identical in hardware to the WRT3200ACM
with a different flash layout and boots zImage rather than uImage.

Specification:
- Marvell Armada 385 88F6820 (2x 1.8GHz)
- 256MB of Flash
- 512MB of RAM
- 2.4GHz (bgn) and 5GHz (an+ac wave 2)
- 4x 1Gbps LAN + 1x 1Gbps WAN
- 1x USB 3.0 and 1x USB 2.0/eSATA (combo port)

Flash instruction:
Apply factory image via web-gui.

Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
2018-05-14 17:20:10 +02:00
Sandeep Sheriker Mallikarjun
27ca6cdc7b at91: Add SAMA5D2 PTC EK board
Add target device as at91-sama5d2_ptc_ek in SAMA5D2 subtarget and
build images for SAMA5D2 PTC Ek board.

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-05-05 06:55:22 +02:00
Sandeep Sheriker Mallikarjun
60750ab505 at91: reorganize at91 subtargets
reorganizing at91 subtargets based on sama5 soc features and this fix
below problems.
  1. able to set neon flags to sama5d2 & sama5d4 subtargets.
  2. fix the make clean which removes all the subtargets in bin folder.
  3. able to configure kernel specific to subtarget.
  4. able to set vfpu4 flags to samad3 subtargets.

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-05-05 06:55:22 +02:00
Sandeep Sheriker Mallikarjun
f34b495a2e uboot-at91: fix DTC command not found.
fixed DTC command not found error while compling uboot-at91. The fix
is to set DTC PATH in uboot-at91 MAKE command.

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-05-05 06:55:22 +02:00
Sandeep Sheriker Mallikarjun
22c398d257 at91: Add SAMA5D27 SOM1 EK board
Add support for SAMA5D27 SOM1 with target device as at91-sama5d27_som1_ek
in SAMA5 subtarget and build images for SAMA5D27 SOM1 Ek board.

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-05-05 06:55:21 +02:00
Sandeep Sheriker Mallikarjun
790b20b6f4 uboot-at91: fetch uboot src from u-boot-at91 github
fetching uboot src from linux4sam/u-boot-at91 github for all at91
target.

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-05-05 06:55:01 +02:00
Sandeep Sheriker Mallikarjun
87f87e45c0 at91bootstrap:update to v3.8.10
updating to new version v3.8.10 and copying at91bootstrap.bin to bin folder.

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-05-05 06:55:01 +02:00
Rosen Penev
3aa28f4833 uboot-envtools: Change download to git.
Currently, the build system uses an openwrt mirror which does not currently
work and FTP can be unreliable under several circumstances. This change
implicitly allows using all the mirrors to download.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-05-02 09:18:26 +02:00
Hauke Mehrtens
9bfca30826 uboot-mvebu: Fix build with libressl 2.7.2
When libressl was linked the libpthread was missing, add it in addition.

Fixes: 2c192b6916 ("tools/libressl: update to version 2.7.2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-04-29 10:13:14 +02:00
Hauke Mehrtens
c21a4c7246 uboot-mxs: Fix build with libressl 2.7.2
When libressl was linked the libpthread was missing, add it in addition.
Also make the mxsimage tool to use the OpenSSL 1.1 API for the recent
libressl version.

Fixes: 2c192b6916 ("tools/libressl: update to version 2.7.2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-04-29 00:57:36 +02:00
Hauke Mehrtens
5ca159ab3b uboot-zynq: Fix build with libressl 2.7.2
When libressl was linked the libpthread was missing, add it in addition.

Fixes: 2c192b6916 ("tools/libressl: update to version 2.7.2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-04-29 00:57:35 +02:00
Damir Samardzic
bdb0de1bbc uboot-envtools: add support for ESPRESSObin and MACCHIATObin
Added for convenience. These boards can be used as dev boards running
various operating systems from different media, and this simplifies work
with U-Boot environment.

Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
2018-04-25 20:37:28 +02:00
Sven Eckelmann
0b20490207 ipq40xx: add support for OpenMesh A62
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
  - 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
  - QCA9888 hw2.0 (PCI)
  - requires special BDF in QCA9888/hw2.0/board-2.bin
    bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
  - triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
  - phy@mdio3:
    + Label: Ethernet 1
    + gmac0 (ethaddr) in original firmware
    + 802.3at POE+
  - phy@mdio4:
    + Label: Ethernet 2
    + gmac1 (eth1addr) in original firmware
    + 18-24V passive POE (mode B)
* powered only via POE

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.

The initramfs image can be started using

  setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
  tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
  set fdt_high 0x85000000
  bootm 0x84000000

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2018-04-23 22:07:22 +02:00
Felix Fietkau
bc43f75def uboot-envtools: remove makefile duplication for supported targets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-20 10:03:38 +02:00
Luis Araneda
68150d3125 uboot-envtools: update to 2018.03
Several changes has been made:

+ AES support has been removed by
  upstream commit c6831c7 (2017-11-14)
  [remove patch "200-fw_env_no_aes.patch"]

+ Support for UBI volumes has beed added by
  upstream commit 34255b9 (2017-11-15)
  [remove patch "300-support-env-in-ubivol-chardev.patch"]

+ A command line argument has beed added ("-c") to manually indicate
  the location of the environment configuration file

Also, patch "400-u-boot-2015.10-stdint.patch" is no longer
necessary, and the config option to enable UBI support has
been removed.

Size comparisons:

fw_printenv size:
Target    Before         After
ar71xx    15,189 bytes   18,133 bytes (+2,944 bytes)
ipq40xx   20,873 bytes   20,987 bytes (+114 bytes)
mvebu     20,881 bytes   20,991 bytes (+110 bytes)
ramips    15,128 bytes   18,072 bytes (+2,944 bytes)

OPKG package size:
Target    Before         After
ar71xx    11,309 bytes   12,875 bytes (+1,566 bytes)
ipq40xx   11,772 bytes   13,299 bytes (+1,527 bytes)
mvebu     11,609 bytes   13,114 bytes (+1,505 bytes)
ramips    10,975 bytes   12,503 bytes (+1,528 bytes)

Compile tested: ipq40xx (musl, glibc, gcc5-musl), ar71xx, mvebu, ramips
Run tested: ipq40xx (ASUS RT-AC58U)

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-04-18 23:59:32 +02:00
Alexander Couzens
f6e6eadc99
packages/uboot-omap: bugfix: serial using ns16550 fifo not enabled
The serial was working before, but not when doing copy&pasting longer
commands in a short time.

Fixes: a4def18f29 ("uboot-omap: Update to u-boot v2017.01")
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2018-04-11 03:43:38 +02:00
Piotr Dymacz
10ea53f900 ramips: add U-Boot env support for ALFA Network AC1200RM
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-04-06 23:11:00 +02:00
Piotr Dymacz
3fc8f50f56 uboot-envtools: fix ALFA Network AWUSFREE1 support
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-04-06 23:11:00 +02:00
Josua Mayer
dff904a955 u-boot-mvebu: update to 2018.03
This release brings various improvements to clearfog support, such as distro-boot.
Obsoletes:
0002-clearfog-reset-usom-onboard-1512-phy.patch
0003-clearfog-enable-distro-boot-code.patch

Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
2018-03-31 16:12:40 +02:00
Josua Mayer
0a3e07b2f5 u-boot-mvebu: set configuration options in Makefile
CONFIG_* variables can easily be set by overriding Build/Configure.
so set NET_RANDOM_ETHADDR=y and CMD_SETEXPR=y here.

This replaces the following patches:
0001-clearfog-generate-random-MAC-address.patch
0004-clearfog-enable-setexpr-command-by-default.patch

Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
2018-03-31 16:12:39 +02:00
Fan Fan
8e1065d681 sunxi: add build for sopine
This will generate image for Pine64 Sopine board.

Signed-off-by: Fan Fan <fkpwolf@gmail.com>
2018-03-23 23:53:20 +01:00
Zoltan HERPAI
ed369e0481 uboot-sunxi: refresh patches
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2018-03-21 17:08:35 +01:00
Hauke Mehrtens
367ee3274d uboot-sunxi: fix build by adding comparabilities for old dtc
We use the dtc from the kernel and that does not have all the options
which u-boot would like to use now. make these parameters optional.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[wigyori@uid0.hu: renamed to 221-compatible-old-dtc.patch from 220-]
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2018-03-21 17:08:19 +01:00
Zoltan HERPAI
7e1e29de75 uboot-sunxi: bump again to 2017.11
Runtime-tested on:
 - Pine64 (A64)
 - Orange Pi 2 (H3)
 - Bananapro (A20)
 - Olimex A20-Micro (A20)
 - Pcduino v3 (A20)
 - Pcduino v2 (A10)

Compile-tested on:
 - all A8/A7/A53 boards

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2018-03-21 17:07:06 +01:00
Paul Wassi
f21cd96400 uboot-kirkwood: update to 2018.03
U-Boot now requires GCC > 5

Catch up with upstream and move some configuration options from
the header files to the corresponding defconfig files.
Also move some options of patch 010 affecting the whole platform
to 010's device only.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2018-03-20 21:45:27 +01:00
Hauke Mehrtens
5d3fbd5996 uboot-mxs: fix compile problems related to OpenSSL
Use the UBOOT_MAKE_FLAGS defined in include/u-boot.mk and do not
overwrite them to compile the host tools against the shipped LibreSSL.
In addition add a patch to fix a compile problem when compiling the
tools against LibreSSL caused by differences in the API between OpenSSL
1.1 and LibreSSL.

This should fix the compile problems seen in build bot from time to time
by not depending on the host libssl-dev package any more but using the
LibreSSL version from OpenWrt.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-17 23:22:40 +01:00
Hauke Mehrtens
8cc22fad6a uboot-mxs: refresh patches
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-17 23:21:58 +01:00
John Crispin
54b275c8ed ipq40xx: add target
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: John Crispin <john@phrozen.org>
2018-03-14 19:04:50 +01:00
Hauke Mehrtens
43f35ce971 uboot-imx6: fix build with GCC 7
Backport the compiler support patches from upstream u-boot to this older
version to make it compile with GCC 7.
This was found by build bot.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-13 22:28:59 +01:00
Felix Fietkau
d85a7f1eb2 uboot-fritz4040: fix build with gcc7
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-03-12 19:31:50 +01:00
Hauke Mehrtens
be3da900cd mvebu: Add subtarget for Cortex A9 build
This is in preparation for adding a subtarget for the Cortex A53 later.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-10 01:15:21 +01:00
Ryan Mounce
9f3f61a0d9 mvebu: add support for Turris Omnia
Adds support for the Turris Omnia and builds an eMMC sysupgrade image in
the same format as the SolidRun ClearFog.

An initramfs image in the simple yet Omnia-specific 'medkit' image format
is also built in order to ease the initial flashing process.

Notable hardware support omissions are support for switching between SFP
cage and copper PHY, and RGB LED control.

Due to a current limitation of DSA, only 1/2 CPU switch uplinks are used.

Specifications:
- Marvell Armada 385 1.6GHz dual-core ARMv7 CPU
- 1GB DDR3 RAM
- 8GB eMMC Flash
- 5x Gigabit LAN via Marvell 88E6176 Switch (2x RGMII CPU ports)
- 1x switchable RJ45 (88E1514 PHY) / SFP SGMII WAN
- 2x USB 3.0
- 12x dimmable RGB LEDs controlled by independent MCU
- 3x Mini PCIe slots
- Optional Compex WLE200N2 Mini PCIe AR9287 2x2 802.11b/g/n (2.4GHz)
- Optional Compex WLE900VX Mini PCIe QCA9880 3x3 802.11ac (2.4 / 5GHz)
- Optional Quectel EC20 Mini PCIe LTE modem

Flash instructions:
If the U-Boot environment has been modified previously (likely manually via
serial console), first use serial to reset the default environment.
=> env default -a
=> saveenv

Method 1 - USB 'medkit' image w/o serial
- Copy openwrt-mvebu-turris-omnia-sysupgrade.img.gz and
omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz to the root of a
USB flash drive formatted with FAT32 / ext2/3/4 / btrfs / XFS.
Note that the medkit MUST be named omnia-medkit*.tar.gz
- Disconnect other USB devices from the Omnia and connect the flash drive
to either USB port.
- Power on the Omnia and hold down the rear reset button until 4 LEDs are
illuminated, then release.
- Wait approximately 2 minutes for the Turris Omnia to flash itself with
the temporary image, during which LEDs will change multiple times.
- Connect a computer to a LAN port of the Turris Omnia with a DHCP client
- (if necessary) ssh-keygen -R 192.168.1.1
- ssh root@192.168.1.1
$ mount /dev/sda1 /mnt
$ sysupgrade /mnt/openwrt-mvebu-turris-omnia-sysupgrade.img.gz
- Wait another minute for the final OpenWrt image to be flashed. The Turris
Omnia will reboot itself and you can remove the flash drive.

Method 2 - TFTP w/ serial
- Extract omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz and copy
dtb + zImage to your TFTP server (rename if desired)
- Connect Turris Omnia WAN port to DHCP-enabled network with TFTP server
- Connect serial console and interrupt U-Boot
=> dhcp
=> setenv serverip <tftp_server_ip_here>
=> tftpboot 0x01000000 zImage
=> tftpboot 0x02000000 dtb
=> bootz 0x01000000 - 0x02000000
- OpenWrt will now boot from ramdisk
- Download openwrt-mvebu-turris-omnia-sysupgrade.img.gz to /tmp/
$ sysupgrade /tmp/openwrt-mvebu-turris-omnia-sysupgrade.img.gz
- Wait another minute for the final OpenWrt image to be flashed. The Turris
Omnia will reboot itself.

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
2018-03-10 01:15:21 +01:00
Vitalij Alshevsky
8584fee310 uboot-sunxi: add Xunlong Orange Pi PC
Signed-off-by: Vitalij Alshevsky <v_alshevsky@tut.by>
2018-02-26 11:23:55 +01:00
Piotr Dymacz
f01b394266 uboot-envtools: add support for ALFA Network AWUSFREE1
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 23:40:16 +01:00
Piotr Dymacz
3b8a858d5c uboot-envtools: add support for YunCore T830
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
f487133322 uboot-envtools: add support for Samsung WAM250
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
c6bd0b4894 uboot-envtools: add support for WHQX E1700AC/E600G/E600GAC v2
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Felix Fietkau
1b13cbc15b grub2: disable building platform code for target utility
It is not used and it was causing a build error with GCC 7.3

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-22 09:30:22 +01:00