Backport patches that separate spectral scan support from general debugfs
support of ath9k/ath10k; this allows to remove the dependency on
KERNEL_RELAY from these driver packages even with debugfs enabled and
avoids the memory footprint of the relay buffers allocated by ath9k/ath10k
even when they aren't used at all.
The KERNEL_RELAY dependency is moved to a new config symbol that enables
spectral scan support in these drivers.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This feature has been unused for years, and its scope is too limited to be
actually useful.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
18090d9 overlay: fix compilation with glibc
2a9a6ea libfstools: optimize building directory string for glob
de6b026 libfstools: support file paths longer than 255 chars
Signed-off-by: John Crispin <john@phrozen.org>
Board Data File (BDF) is loaded upon driver boot-up procedure. The right
board data file is identified on QCA4019 using bus, bmi-chip-id and
bmi-board-id.
The problem, however, can occur when the (default) board data file cannot
fulfill the vendor requirements and it is necessary to use a different
board data file.
This problem was solved for SMBIOS by adding a special SMBIOS type 0xF8.
Something similar has to be provided for systems without SMBIOS but with
device trees. No solution was specified by QCA and therefore a new one has
to be found for ath10k.
The device tree requires addition strings to define the variant name
wifi@a000000 {
status = "okay";
qcom,ath10k-calibration-variant = "RT-AC58U";
};
wifi@a800000 {
status = "okay";
qcom,ath10k-calibration-variant = "RT-AC58U";
};
This would create the boarddata identifiers for the board-2.bin search
* bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=RT-AC58U
* bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=RT-AC58U
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Use the generic board detection method:
- Board name: First compatible string from the device tree
- Board model: Model property from the device tree
Change occurrences of board name in userspace by the compatible
string, and removed target specific board detection script
Replace the definition of SUPPORTED_DEVICES in Device/Default
to extract the dt compatible string from each device definition.
Additionally, for devices supported by lede-17.01, append
the value of BOARD_NAME to SUPPORTED_DEVICES in the device
definition.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
There are only artifacts for these boards in our tree and not even
partial support.
Drop teh stale files.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Commit 30f61a34b4 claimed to drop -d & -p
options. In reality only -d was dropped. Update command help text to
reflect that -d is no longer a supported option.
Fixes FS#1187
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
More important bug fix:
402f05c Use full-rate mtu_time in all tins. Fixes an issue where some
cake tins experienced excessive latency since 49776da (dynamically
adjust target)
Minor bug fixes:
31277c2 Avoid unsigned comparison against zero. Fix compiler warning,
no known impact.
8cf5278 ack_filter: fix TCP flag check. A very contrived case may have
lead to dropping a SYN packet that should not be dropped.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Certain DHCP servers push a gateway outside of the assigned interface subnet,
to support those situations, install a host route towards the gateway.
If Gateway and IP are served in same network, openwrt quagga cannot learn
routes (rip routes are not getting added, showing inactive) whereas
working fine when Gateway and IP are in different network.
Signed-off-by: Mogula Pranay <mogula.pranay@nxp.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Renaming an atm etherbride using 'ip link' (via hotplug) is racy since the
original netdev might disappear before br2684ctl has finished appling it's
setting:
local2.notice br2684ctl[1667]: Interface "nas0" created sucessfully
local2.notice br2684ctl[1667]: Communicating over ATM 0.8.35, encapsulation: LLC
kern.info kernel: dsl0: renamed from nas0
kern.err kernel: br2684:br2684_regvcc: tried to attach to non-existent device
local2.err br2684ctl[1667]: Could not configure interface:No such device or address
By passing the final used netdev name to br2684ctl_wrap another race
condition workaround will be enabled again.
Change the lantiq ptm driver to create a netdev with the name dsl as well.
Albeit the rename via 'ip link' works fine so far, using a different
approach for ptm then atm could be confusing.
Signed-off-by: Mathias Kresin <dev@kresin.me>
br2684ctl starts automatically, set up reload triggers, which fire as soon
as a atm driver is loaded. No need to do the reload via the script.
The reload is only required as soon as we can reliable switch between atm
and ptm driver and need to be implemented in a race free way.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add the uci option nameprefix to specifc a target netdev name. Patch the
br2684ctl code to accept and set a netdev name via commandline parameters.
It allows to use the same netdev name for ATM and PTM lines on lantiq
xdsl hardware.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Mathis Kresin <dev@kresin.me>
These packages are needed to generate the image, better mark them hidden
so we will activate them based on which boards gets build and they will
be activated always when the board which needs then gets build.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These packages are needed to generate the image, better mark them hidden
so we will activate them based on which boards gets build and they will
be activated always when the board which needs then gets build.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The fixes following problems
1. changing prefix at91bootstrap to AT91bootstrap will fix the default
selection of at91bootstrap for the selected sama5 subtarget.
2. fixed missing default selection of sama5d4 nand flash for the
selected sama5d4 subtarget.
3. corrected at91bootstrap Title name.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
neon and VFPv4 support is added to this target and uboot-at91 build
fails due to TARGET_CFLAGS -mfloat-abi set to hard. as a fix, setting
uboot-at91 CFLAGS -mfloat-abi=soft.
Fixes: 01cc6bd495 ("at91: sama5: activate fpu")
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Fixes the following dependency error encountered by the buildbots:
Package kmod-w1 is missing dependencies for the following libraries:
hwmon.ko
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
add an uboot able to boot a kernel in an ubi partition
This uboot also has a "recovery" feature, before
booting from flash it will try to boot a initramfs
image called "initramfs.bin" from a FAT32-formatted
USB drive connected to the USB 2.0 port.
(u-boot lacks drivers for usb 3.0 controllers)
Just rename the initramfs image and place it on
the usb drive, the uboot will load it.
In case there is no USB drive or no such file
is found, the uboot will boot from internal flash.
The whole check takes less than a second, boot times
are not impacted.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Use <manufacturer>_<modelname> as image name.
Use the BOARD_NAME variable to ensure that the former used boardname is
still used as the subdirectory name for the sysupgrade-tar image, to
not break sysupgrade from earlier versions.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Build the Seagate GoFlexHome u-boot for the Seagate GoFlexNet as well. The
name clearly indicates that the u-boot can be used for both boards
Build the Zyxel NSA310 u-boot if the NSA310B image is selected.
Signed-off-by: Mathias Kresin <dev@kresin.me>
No image build code for the Guruplug, Sheevaplug and NSA310S exists. Drop
support for the boards for now.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the "low" and "high" values to configure the GPIO as an output with
that initial value. It ensures that the gpio doesn't have a unwanted value
during the time the direction is set to ouput and the actual value is
applied.
We don't need to take care of the GPIO polarity for now, since our
exported GPIOs are always active low.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Start gpio_switch before the boot state is set to up/initialised/done.
This way the exported GPIOs are available at the time rc.local is started.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Previously this was only activated for ADSL, this patch activates the
same setting also for VDSL, this feature is also support for VDSL in the
same way it works for ADSL.
I tested it with DSL FW 5.7.9.5.1.7 against a Broadcom 177.140 DSLCO
(Deutsche Telekom) and saw different data rates and Max. Attainable Data
Rates depending on the ds_snr_offset settings I choose.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The previous commit was incorrectly rebased and referred to a not
yet existing PROJECT_GIT variable.
Fixes: d86a269c1f libubox: update to latest git HEAD
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2a9a6ea libfstools: optimize building directory string for glob
de6b026 libfstools: support file paths longer than 255 chars
Signed-off-by: John Crispin <john@phrozen.org>
The NXP 74HC164 GPIO expander driver uses a different config symbol
("CONFIG_GPIO_74X164") and module name since since at least Kernel
version 2.6.37.
Update the kmod package definition accordingly by adjusting kconfig
and module file names.
This unrelated, but correct change has been separated from the
WNR2000v5 support commits.
Ref: https://github.com/lede-project/source/pull/1256
Suggested-by: Raphael Catolino <raphael.catolino@gmail.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Instead of inferring the availability of NEON support from the target
optimization flags, use a preprocessor test to decide whether to enable
ARMv8 NEON optimizations.
Fixes the following build error spotted by the mediatek/32 buildbot:
[ 26%] Building C object CMakeFiles/zlib.dir/contrib/arm/inflate.o
In file included from .../zlib-1.2.11/contrib/arm/chunkcopy.h:10:0,
from .../zlib-1.2.11/contrib/arm/inflate.c:87:
.../arm_neon.h:31:2: error: #error You must enable NEON instructions (e.g. -mfloat-abi=softfp -mfpu=neon) to use arm_neon.h
#error You must enable NEON instructions (e.g. -mfloat-abi=softfp -mfpu=neon) to use arm_neon.h
^
In file included from .../zlib-1.2.11/contrib/arm/inflate.c:87:0:
.../zlib-1.2.11/contrib/arm/chunkcopy.h:18:9: error: unknown type name 'uint8x16_t'
typedef uint8x16_t chunkcopy_chunk_t;
^
[...]
CMakeFiles/zlib.dir/build.make:302: recipe for target 'CMakeFiles/zlib.dir/contrib/arm/inflate.o' failed
Fixes: 3acecba520 "package/libs/zlib: Add ARM and NEON optimizations"
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
In order to properly support 802.11w, hostapd needs to advertise a group
management cipher when negotiating associations.
Introduce a new per-wifi-iface option "ieee80211w_mgmt_cipher" which
defaults to the standard AES-128-CMAC cipher and always emit a
"group_mgmt_cipher" setting in native hostapd config when 802.11w is
enabled.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
When using the uci.sh wrapper, allow parameters to match those supported
by the uci binary i.e. "uci rename <config>.<section>[.<option>]=<name>".
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Some packages such as Python/Python3 (host pip/pip3) needs this
to compile.
More detailed explanation provided by Alexandru:
"i need the zlib/host for Python/Python3 ; because, it seems the
host pip/pip3 needs this to work ; i suspect in older versions
this worked, because some of the host's build env would be used
in the build, and then the zlib-dev from the host distro would
be used ; now, the host-build does not seem to have any
-I/usr/include stuff, which is good
and it also seems that Python/Python3 does not like it if the
zlib-dev package is too old, so using this zlib/host would be
good for this as well"
Source:
https://github.com/lede-project/source/pull/1329#issuecomment-351055861
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Add option to use O3 optimization as not all devices have
space constraints. This option is default using GCC in upstream
but isn't in the CMake makefile for some reason.
Source: https://github.com/madler/zlib/blob/master/configure#L170
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Usage documentation for 'procd_send_signal' states "The signal is SIGHUP
by default, and must be specified by NAME." Make actual behaviour match
the stated documented behaviour.
https://wiki.openwrt.org/inbox/procd-init-scripts
Suggested-by: Jo-Philip Wich <jow@mein.io>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
a5954cf procd: Add %m to several functions that return errno.
810d7a5 procd: Remove redundant errno variable in several printf functions.
fa5ce1c procd: Replace strerror(errno) with %m.
Signed-off-by: John Crispin <john@phrozen.org>
Add the uas(p) module to the modules loaded early on the boot process.
The uas(p) is an modern alternative, which is used by the modern USB3
storage cases, compared to the bot protocol. To be able to use uas(p)
storage cases for extroot, the kernel module has to be loaded before the
search for extroot has been called. This patch changes the load order to
support uas(p) storage cases for extroot.
Signed-off-by: Daniel Albers <daniel.albers@public-files.de>
11efbf3 overlay: fix race condition when switching to jffs2
bdeb95a libblkid-tiny: add support for NTFS superblock
ef2cc03 fstools: Replace strerror(errno) with %m format.
98fd5b4 libblkid-tiny: add support for UBI superblock
Signed-off-by: John Crispin <john@phrozen.org>
Use flock to protect init script from concurrent execution
(of the same script).
Important for services which generate native config files.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: Andrejs Hanins <ahanins@gmail.com>
This is needed for procd init script protection to work.
flock adds 4248 bytes to stripped busybox binary.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
In the add_match function in libbb/lineedit.c in BusyBox through 1.27.2,
the tab autocomplete feature of the shell, used to get a list of filenames
in a directory, does not sanitize filenames and results in executing any
escape sequence in the terminal. This could potentially result in code
execution, arbitrary file writes, or other attacks.
Fixes: FS#1181 - CVE-2017-16544:
Backport the patch from:
https://git.busybox.net/busybox/commit/?id=c3797d40a1c57352192c6106cc0f435e7d9c11e8https://nvd.nist.gov/vuln/detail/CVE-2017-16544
Signed-off-by: Derek Werthmuller <thewerthfam@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
In current state, if there is START but no STOP, enbale()
will return 1 (failure), which is wrong.
Moreover there is no need to check for START/STOP twice.
Instead, add err variable to save success state and
and return it's value.
Also eliminate the need to disable() by using 'ln -sf',
which will first delete the old symlink if one exists.
Changes from v1:
- fixed description
Signed-off-by: Roman Yeryomin <roman@advem.lv>
5beb95d lua: additionally return name when looking up sections
ff33bb2 lua: support extended section notation
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Fix overhead accounting error introduced by f33c4d6 refactor
cake_advance_shaper and ack_filter
Symptoms were links running under rate.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Enabling IPTABLES_NFTABLES resulted in an error during build:#
*** No rule to make target '../extensions/libext.a',
needed by 'xtables-compat-multi'."
Comments from Alexander Lochmann and Fedor Konstantinov in FS#711
provided fixes for this build error, allowing iptables to compile.
https://bugs.lede-project.org/index.php?do=details&task_id=711.
This commit updates the Makefile.am xtables_compat_multi_LDFLAGS
and _LDADD, moving linking of extensions to LDFLAGS.
Signed-off-by: rektide de la faye <rektide@voodoowarez.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Fixes: 8170f280c4 ("base-files: set FAILSAFE in /etc/profile when
/tmp/.failsafe exists")
Since dropbear clears the environment, FAILSAFE was not set as intended in
failsafe mode. This also broke sysupgrade from failsafe mode over SSH.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Unconditionally pass TARGET_CPPFLAGS (not passed at all before) and
TARGET_LDFLAGS (passed only in certain non-default configuration before the
Makefile streamlining). Without these flags, hardening options
(PKG_FORTIFY_SOURCE and PKG_RELRO) were not actually applied to busybox.
The addition of these flags increases the size of the stripped busybox
binary by about 6KB (~4KB with fortify headers, ~2KB with "-znow -zrelro")
with the default hardening options PKG_FORTIFY_SOURCE_1 and PKG_RELRO_FULL.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Use default Build/Install steps where possible. No binary change in default
configuration, so PKG_RELEASE is not incremented.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Send a SIGHUP signal via procd to the dnsmasq service so the instance(s)
re-read(s) the /tmp/hosts/dhcp config.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
If the hostname in /etc/config/system is modified the dnsmasq should also
get triggered to rewrite/reload the config.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
PKG_BUILD_DIR was defined with quoting PKG_VERSION in
layerscape package makefiles. Now PKG_VERSION has been
removed from these makefiles. When PKG_BUILD_DIR quotes
PKG_VERSION, '=' should be used instead ':=' to make
sure PKG_VERSION has been defined in common makefile.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Intel motherboards (as well as the Cavium ThunderX SoC) use a
superset of the I2C protocol called SMBus.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
439b9b6c (tag: v1.29.0) Update manual pages
48498452 Bump up version number to v1.29.0, LT revision to 29:1:15
d30f3816 Update manual pages
4d1139f6 Remove SPDY
48f57407 nghttpx: Update doc
c1f14d73 Update manual pages
216f4dad nghttpx: Remove redundant check
a4e27d76 Revert "nghttpx: Use an existing h2 backend connection as much as possible"
2365f12e Fix CMAKE_MODULE_PATH
03f7ec0f nghttpx: Write API request body in temporary file
2056e812 nghttpx: Increase api-max-request-body
1ebb6810 nghttpx: Faster configuration loading with lots of backends
a3ebeeaf nghttpx: Fix crash with --backend-http-proxy-uri option
422ad1be Use NGHTTP2_REFUSED_STREAM for streams which are closed by GOAWAY
97f1735c Bump up version number to 1.29.0
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
f40f84c support PantechMode
d8dc335 support Quanta and Blackberry modes
333e486 fix support for Option modems
Signed-off-by: John Crispin <john@phrozen.org>
7aa2594 odhcpd: Replace strerror(errno) with %m format
750e457 Support muliple RAs on single interface
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The git hash was changed for multiple layerscape packages without
changing the version number. The LEDE build system will not download the
packages again if the old version is already there and so some people
and the build bots are using wrong version of some packages. Use
PKG_SOURCE_DATE instead of PKG_VERSION to generate packages with the
date and the first charterers of the git hash. This will change the file
name and make the build system download them again, also if in future
the git hash is changed the file name will change and trigger a new
download.
This should fix a problem spotted by build bot.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The LinkIt Smart 7688/LinkIt Smart 7688 Duo are identical beside the
extra ATmega32U4 - accessible via UART - on the the Duo.
Since all relevant hardware is identical, drop the Duo special handling
in userspace.
Signed-off-by: Mathias Kresin <dev@kresin.me>
In commit 2b1ec44dbd ("layerscape: add ls1012afrdm device support")
The git revision and the mirror hash for this package was updated to a
version which includes ls1012afrdm-uboot.bin, but the file name at
dl/uboot-layerscape-armv8_32b-2017.09.tar.xz staid the same. This way
most user did not download the new version but used the old file.
Convert this package to the normal git clone parameters by using
PKG_SOURCE_DATE instated of PKG_VERSION, now the file name in dl also
contains the git hash and should change every time the git hash is
updated.
This should fix a problem spotted by build bot.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
LEDE Flyspray Task 1091:
Fix libiconv-full 'undefined reference' compile linker error using GCC7 Musl
Tested with targets x86 (i386 and x86_64)
Addition of CFLAGS "std=gnu89" fixes the linker issues, credit to harrylwc
Issue found with 'minidlna' package, which depends on 'libiconv-full'
Error in compile log:
../lib/.libs/libiconv.so: undefined reference to `aliases_lookup'
../lib/.libs/libiconv.so: undefined reference to `aliases2_lookup'
collect2: error: ld returned 1 exit status
Makefile:64: recipe for target 'iconv_no_i18n' failed
Signed-off-by: Jake Staehle <jacob@staehle.us>
Use <manufacturer>_<modelname> as image name.
Use the BOARD_NAME variable to ensure that the former used boardname is
still used as the subdirectory name for the sysupgrade-tar image, to
not break sysupgrade from earlier versions.
While at it, normalise the image filenames by using only lower case
characters and bin as file extension for sysupgrade images.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the first compatible string as board name in userspace. Add the new
board name as well as the former used board name to the image metadata
to keep compatibilty with already deployed installations.
Don't add the former used boardname for boards which exists only in
master or evaluation boards.
Signed-off-by: Mathias Kresin <dev@kresin.me>
kmod-lib-lzo and kmod-lib-lz4 depend in kernel 4.14 on
kmod-crypto-acompress, add this missing dependency.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CONFIG_FRAMEBUFFER_CONSOLE does not activate new modules any more in
kernel 4.14, but CONFIG_FRAMEBUFFER_CONSOLE is now a boolean option
which change the kmod-fb package. kmod-fbcon should be split up.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This deactivates the following options which were introduced between
kernel 4.9 and 4.14 in some kernel packages:
CONFIG_INET_ESP_OFFLOAD
CONFIG_INET6_ESP_OFFLOAD
CONFIG_LWTUNNEL_BPF
CONFIG_NET_9P_XEN
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In kernel 4.14 kmod-bluetooth depends on kmod-crypto-ecdh, add
kmod-crypto-ecdh to LEDE.
Both packages also depend on the kmod-crypto-kpp package. To build this
we have to fix the dependency of CRYPTO_ECDH which has a typo.
This patch is already accepted upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In kernel 4.14 kmod-crypto-hw-ccp depends on kmod-crypto-rsa, add it.
kmod-crypto-rsa also packages the ASN1 parser and some other code which
is currently only used by this module.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In kernel 4.14 kmod-dm depends on kmod-dax.
Add DAX: "Direct access to differentiated memory" to LEDE.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In kernel 4.14 hwmon support can be deactivated for the tg3 driver,
deactivate it by default to save some space.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The default e1000e parameters (interrupt throttling rate, MSI/MSI-X
mode) are optimized for desktop and server computers to optimize
user-space execution (i.e. what's typically referred to as "useful"
work). This assumption breaks on a router under load where most of
the "useful" work actually takes place either in hardware interrupt
handlers (IRQ) or at software IRQ (swirq) modes, so we try to reflect
that by overriding these parameters with more appropriate values.
Patch-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
There has been recent significant activity with the cake qdisc of late
Some of that effort is related to upstreaming to kernel & iproute2
mainline but we're not quite there yet. This commit teaches tc how to
activate and interprete the latest cake operating modes, namely:
ingress mode: Instead of only counting packets that make it past the
shaper, include packets we've decided to drop as well, since they did
arrive with us on the link and took link capacity.
This mode is more suitable for shaping the ingress of a link
(e.g. from ISP) rather than the more normal egress.
ack-filter/ack-filter-aggressive: Filter excessive TCP ACKS. Useful in
highly assymetric links (downstream v upstream capacity) where the
majority of upstream link capacity is occupied with ACKS for downstream
traffic.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
There has been recent significant activity with the cake qdisc of late
but in the cobalt branch. Some of that effort is related to upstreaming
to kernel & iproute2 mainline but we're not quite there yet. Relevant
feature changes:
ingress mode: Instead of only counting packets that make it past the
shaper, include packets we've decided to drop as well, since they did
arrive with us on the link and took link capacity.
This mode is more suitable for shaping the ingress of a link
(e.g. from ISP) rather than the more normal egress.
ptm mode: Minor optimisation in packet overhead calculation.
dual-src/dsthost/triple-isolate: Optimise only calculating src or dst
host hashes only if required.
ack-filter/ack-filter-aggressive: Filter excessive TCP ACKS. Useful in
highly assymetric links (downstream v upstream capacity) where the
majority of upstream link capacity is occupied with ACKS for downstream
traffic.
A separate iproute2 patch to teach it about Cake's new features will
follow.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Remove PACKAGE_uhttpd_debug config as this is an unused leftover
Add CONFIG_uhttpd_lua to PKG_CONFIG_DEPENDS
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Including version.mk sets PKG_CONFIG_DEPENDS to config entries used for
VERSION_SED command. We should keep these configs to make sure package
gets refreshed when needed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Since /overlay/upper appeared, -b ignored -c silently (cause it was
still checking for /overlay/etc). Now, if /overlay/upper is absent,
sysupgrade -c will fail and exit verbosely.
Fix -l to consider -c (it never did).
Clean up to always use /overlay/upper/xxx instead of still checking
for /overlay/xxx.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Lantiq and IPQ806X (which includes IPQ40XX) both define the
same custom function {ipq806x|lantiq}_get_dt_led.
This patch moves the function into the base-file package at
lib/functions/leds.sh to make it more accessible for other
targets as well.
Cc: Mathias Kresin <dev@kresin.me>
Cc: John Crispin <john@phrozen.org>
Cc: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
To not clutter the system when building an opkg free image, generate the
distfeeds.conf only if CLEAN_IPKG is unset.
Since opkg is now a shared package, we can't rely on PACKAGE_opkg, but
since opkg is not reasonably usable without the status information, we
can tie the distfeeds.conf to it.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Ensure /etc/opkg exists before trying to write there. This fixes a build
failure if SIGNED_PACKAGES is disabled.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
All the relevant options used for distfeeds.conf are part of base-files,
so it makes more sense to move the file there as well.
This has the added benefit that the we can share the opkg package again,
reducing the amount of target specific packages.
Acked-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Bump to latest WireGuard snapshot release:
44f8e4d version: bump snapshot
bbe2f94 chacha20poly1305: wire up avx512vl for skylake-x
679e53a chacha20: avx512vl implementation
10b1232 poly1305: fix avx512f alignment bug
5fce163 chacha20poly1305: cleaner generic code
63a0031 blake2s-x86_64: fix spacing
d2e13a8 global: add SPDX tags to all files
d94f3dc chacha20-arm: fix with clang -fno-integrated-as.
3004f6b poly1305: update x86-64 kernel to AVX512F only
d452d86 tools: no need to put this on the stack
0ff098f tools: remove undocumented unused syntax
b1aa43c contrib: keygen-html for generating keys in the browser
e35e45a kernel-tree: jury rig is the more common spelling
210845c netlink: rename symbol to avoid clashes
fcf568e device: clear last handshake timer on ifdown
d698467 compat: fix 3.10 backport
5342867 device: do not clear keys during sleep on Android
88624d4 curve25519: explictly depend on AS_AVX
c45ed55 compat: support RAP in assembly
7f29cf9 curve25519: modularize dispatch
Refresh patches.
Compile-test-for: ar71xx
Run-tested-on: ar71xx Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
As MD5 is known weak for many years and more and more
penetration test tools complain about enabled MD5 HMAC
I think it's time to drop it.
By disabling the MD5 HMAC support dropbear will also
automatically use SHA1 for fingerprints.
This shouldn't be a problem too.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Add config option which allows to enable/disable DHCP support at compile
time. Make DHCPv6 support dependant on DHCP support as DHCPv6 support
implies having DHCP support.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
- use %d instead of %n for opkg feed identifiers
- remove %n / %N references from version files
Fixes bf5cef47b3 merge: release/banner: drop release name and update banner.
Fixes FS#1213.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
udhcpc doesn't send a hostname by default. Use the system hostname if
nothing else is specified, to always send a hostname.
It syncs the behaviour to odhcpc, which always sends a hostname.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
Kernel and rootfs in a subdirectory matching the userspace boardname,
was intended to use a single sysupgrade-tar archive for multiple boards
with different kernel/rootfs images. This feature was never used.
Use the first found directory in the tar archive instead of relying on
a directory named according to the userspace boardname.
It allows to change the boardname without adding another compatibility
layer - using the nand_board_name() function - for (sub)targets using
the metadata based image validation in favour to
nand_do_platform_check().
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch fixes two issues with the current get_partitions()
function.
First: "Invalid partition table on $disk" will pop up on
legitimate images on big endian system.
This is because the little-endian representation of "55 AA" is
assumed in the context of little-endian architectures. On these
comparing it to the 16-bit word 0xAA55 does work as intented.
Whereas on big-endian systems, this would have to be 0x55AA.
This patch fixes the issue by replacing the integer conversion
and value match check with just a string comparision.
Second: The extraction of the type, start LBA and LBA num from
the partition table has the same endianness issue. This has been
fixed by using the new hex_le32_to_cpu() function. This function
will translate the stored little-endian data to the correct
byte-order if necessary.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch updates ath10k-firmware to use the
firmware-5.bin_10.4-3.2.1-00058 firmware for the QCA4019.
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
d02a05b mt7603: update firmware to version 20160107100755
4d4cd05 Partially revert "mt7603: use mcu command to set timing registers, fix OFDM timeout values"
170f334 mt76x2: remove MAC address limitation for multi-vif setups
3563b8f mt76x2: clean up MAC/BSSID address initialization
9de77e1 mt76x2: drop wiphy->addresses
a6a6e25 mt76x2: init: disable APCLI by default
c64633e mt76x2: configure rx filter based on monitor mode setting
ac815fa mt76x2: init: fix rx filter default value during init
e504656 mt7603: configure other-unicast drop based on monitor mode setting
Signed-off-by: Felix Fietkau <nbd@nbd.name>
add no-ssl3-method again as 1.0.2n compiles without the ssl3-method(s)
Fixes CVEs: CVE-2017-3737, CVE-2017-3738
Signed-off-by: Peter Wagner <tripolar@gmx.at>
