Refreshed all patches.
Added new patch:
- 192-Revert-ubifs-xattr-Don-t-operate-on-deleted-inodes.patch
This fixes a bug introduced in upstream 4.14.68 which caused targets using
ubifs to produce file-system errors on boot, rendering them useless.
Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Refresh patches.
Remove patch that can be reverse applied:
mvebu/patches-4.14/530-ATA-ahci_mvebu-enable-stop_engine-override.patch
mvebu/patches-4.14/531-ATA-ahci_mvebu-pmp-stop-errata-226.patch
Update patch that no longer applied:
ipq806x/patches-4.14/0035-clk-mux-Split-out-register-accessors-for-reuse.patch
Compiled-tested-for: lantiq, ramips
Run-tested-on: lantiq BT hh5a, ramips MIR3g
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tested-by: Michael Yartys <michael.yartys@protonmail.com>
Tested-by: Rosen Penev <rosenp@gmail.com>
Marvell ahci hardware requires a workaround to prevent eSATA failures
on hotplug/reset when used with multi-bay external enclosures.
Errata Ref#226 - SATA Disk HOT swap issue when connected through Port
Multiplier in FIS-based Switching mode.
These patches backport the workaround from 4.17.
Signed-off-by: Jeremiah McConnell <miah@miah.com>
For easier future kernel bumps replace spi patch with upstream version
slightly modified. The modification removes partition definitions which
has been diffrent for some U-Boot versions.
Also this removes unnecessary i2c definition which was in the old patch.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Since the beginning there's been an issue with initializing the Atheros
based MiniPCIe wireless cards. Here's an example of kerenel log:
OF: PCI: host bridge /soc/pcie@d0070000 ranges:
OF: PCI: MEM 0xe8000000..0xe8ffffff -> 0xe8000000
OF: PCI: IO 0xe9000000..0xe900ffff -> 0xe9000000
advk-pcie d0070000.pcie: link up
advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [mem0xe8000000-0xe8ffffff]
pci_bus 0000:00: root bus resource [io 0x0000-0xffff](bus address[0xe9000000-0xe900ffff])
pci 0000:00:00.0: BAR 0: assigned [mem0xe8000000-0xe801ffff 64bit]
pci 0000:00:00.0: BAR 6: assigned [mem0xe8020000-0xe802ffff pref]
[...]
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x3c
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x44
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4
ath9k 0000:00:00.0: enabling device (0000 -> 0002)
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x3c
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0xc
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x40
ath9k 0000:00:00.0: request_irq failed
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4
ath9k: probe of 0000:00:00.0 failed with error -22
The same happens for ath5k cards, while ath10k card didn't appear at
all (not detected):
OF: PCI: host bridge /soc/pcie@d0070000 ranges:
OF: PCI: MEM 0xe8000000..0xe8ffffff -> 0xe8000000
OF: PCI: IO 0xe9000000..0xe900ffff -> 0xe9000000
advk-pcie d0070000.pcie: link never came up
advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [mem0xe8000000-0xe8ffffff]
pci_bus 0000:00: root bus resource [io 0x0000-0xffff](bus address[0xe9000000-0xe900ffff])
advk-pcie d0070000.pcie: config read/write timed out
Following the issue on esppressobin.net forum [1] the workaround seems
to be limiting the speed of PCIe bridge to 1st generation. This fixed
the initialisation of all tested Atheros wireless cards.
The change shouldn't affect the performance for wireless cards,
it could reduce the performance of storage controller cards but since
OpenWrt focuses on wireless connectivity, fixing compatibility with
wireless cards should be a priority.
For the record, the iwlwifi and mt76 cards were not affected by this
issue.
1. http://espressobin.net/forums/topic/which-pcie-wlan-cards-are-supported
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
The console bootarg is being corrupted on boot, causing various issues
including broken sysupgrade.
Utilising the bootargs mangle patch from other targets, hardcode the console
arguments and fetch the rootfs from the bootloader.
Kernel command line: console=ttyS0,115200 root=/dev/mtdblock8
Bootloader command line (ignored): console= root=/dev/mtdblock8
Please cherry pick to 18.06 too
Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
Linksys WRT32X (Venom) is identical in hardware to the WRT3200ACM
with a different flash layout and boots zImage rather than uImage.
Specification:
- Marvell Armada 385 88F6820 (2x 1.8GHz)
- 256MB of Flash
- 512MB of RAM
- 2.4GHz (bgn) and 5GHz (an+ac wave 2)
- 4x 1Gbps LAN + 1x 1Gbps WAN
- 1x USB 3.0 and 1x USB 2.0/eSATA (combo port)
Flash instruction:
Apply factory image via web-gui.
Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
Newer Linksys boards might come with a Winbond W29N02GV which can be
configured in different ways. Make sure we configure it the same way as
the older chips so everything keeps working.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
A regression seriously affecting the Linksys WRT1900ACv1 (Mamba) was
introduced some time between the OpenWrt/LEDE v4.4 and v4.9 kernels.
The root cause has not yet been identified, despite many attempts for
more than a year. Disabling the SoC specific CPU idle support should
mitigate this issue.
The symptoms on an affected system are unwanted reboots at a variable
frequency. In many cases almost immediately after boot, causing a
bootloop. This effectively disables support for Mamba on OpenWrt
with kernels > v4.4.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The internal RTC does not work correctly on these Linksys boards based
on Marvell SoCs. It is off by 3 minutes in 10 minutes running, this
was reported by multiple users. On the Linksys Mamba device the device
tree comment says that no crystal is connected to the internal RTC, this
is probably also true for the other devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some boards like the Turris Omnia have an RTC chip that does not get
initialized. Initializing the RTC at the driver level helps get rid of
bootloader hacks that write special register values.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This makes some of the mtd patches apply again after some generic
patches were changed.
These problems where found by build bot.
Fixes: ac9bcefa3b ("kernel: use V10 of mtd patchset adding support for "compatible" string")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit introduces new subtarget for Marvell EBU Armada Cortex A53
processor based devices.
The first device is Globalscale ESPRESSObin. Some hardware specs:
SoC: Marvell Armada 3700LP (88F3720) dual core ARM Cortex A53
processor up to 1.2GHz
RAM: 512MB, 1GB or 2GB DDR3
Storage: SATA interface
µSD card slot with footprint for an optional 4GB EMMC
4MB SPI NOR flash for bootloader
Ethernet: Topaz Networking Switch (88E6341) with 3x GbE ports
Connectors: USB 3.0
USB 2.0
µUSB port connected to PL2303SA (USB to serial bridge
controller) for UART access
Expansion: 2x 46-pin GPIO headers for accessories and shields with
I2C, GPIOs, PWM, UART, SPI, MMC, etc
MiniPCIe slot
Misc: Reset button, JTAG interface
Currently booting only from µSD card is supported.
The boards depending on date of dispatch can come with various U-Boot
versions. For the newest version 2017.03-armada-17.10 no manual
intervention should be needed to boot OpenWrt image. For the older ones
it's necessary to modify default U-Boot environment:
1. Interrupt boot process to run U-Boot command line,
2. Run following commands:
(for version 2017.03-armada-17.06 and 2017.03-armada-17.08)
setenv bootcmd "load mmc 0:1 0x4d00000 boot.scr; source 0x4d00000"
saveenv
(for version 2015.01-armada-17.02 and 2015.01-armada-17.04)
setenv bootargs "console=ttyMV0,115200 root=/dev/mmcblk0p2 rw rootwait"
setenv bootcmd "ext4load mmc 0:1 ${fdt_addr} armada-3720-espressobin.dtb; ext4load mmc 0:1 ${kernel_addr} Image; booti ${kernel_addr} - ${fdt_addr}"
saveenv
3. Poweroff, insert SD card with OpenWrt image, boot and enjoy.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
As at this commit, DSA is not enabled in the kernel config for mvebu, so these
nodes have been ignored. In preparation for the first mvebu board using DSA,
disable these nodes for existing boards to avoid issues.
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
This patch bumps the 4.14 kernel to .23.
- Refreshed patches.
- Deleted bcm53xx/patches-4.14/089-PCI-iproc-Fix-NULL-pointer-dereference-for-BCMA.patch. Has been accepted upstream.
- Deleted generic/pending-4.14/821-usb-Remove-annoying-warning-about-bogus-URB.patch. The upstream URB code was changed,
the patch no longer applies. I discussed this with the patch author and removed it for now, we'll see how it goes.
Compile-tested on: ramips/mt7621, x86/64
Run-tested on: ramips/mt7621, x86/64
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Add the patch for reprobing phys also for 4.14, as it is still needed.
Fixes: 4ccad92229 ("mvebu: Add support for kernel 4.14")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
When SFP support was accepted upstream, the expected GPIO names were
slightly changed, breaking SFP insert detection. Update the DTS file to
the expected name to make SFP work again.
Fixes: 4ccad92229 ("mvebu: Add support for kernel 4.14")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Add support for kernel 4.14 to the mvebu target.
This also replaces the old sfp and phylink patches with new versions
from Russell's clearfog-4.13 branch
http://git.arm.linux.org.uk/cgit/linux-arm.git/log/?h=clearfog-4.13
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
