Now that IPV6 isn't build as a module anymore, we don't need to decouple
bridge from ipv6 anymore.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 47751
In old days mtd_add_partition was checking for partitions overlapping
which was breaking our splitting feature. We had to modify this function
by adding an extra bool dup_check parameter. Upstream commit:
3a434f66e6da ("mtd: part: Remove partition overlap checks")
removed that check so we don't need our modification anymore.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47748
For a long time we have a dedicated firmware splitter for uimage as a
replacement for the one builtin into mtd subsystem. For a year we got a
proper warning for users sticking to the old one (r43700). It should be
really safe to drop it now, especially since we do it for 4.4 only.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47747
Include /lib/functions/system.sh in 02_network to define missing
mtd_get_mac_binary() procedure.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47723
This removes calls to ucidef_set_interfaces_lan_wan() and
ucidef_set_interfaces_lan() on boards where all relevant info can be
inferred from the switch definition.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47722
This changes uci-defaults-new.sh, config_generate and all relevant board.d
files in order combine ucidef_add_switch() and ucidef_add_switch_ports() into
a single function.
Also removes now superfluous enable and reset arguments.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47721
Out of 69 switch definitions, only 3 pass something different than "1" as
values for reset and enable, with one of those three being invalid.
This change ...
* removes the reset and enable arguments from ucidef_add_switch()
* unconditionally writes reset:1 and enable:1 to JSON
* converts the three users of nonstandard values to ucidef_add_switch_attr()
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47720
This migrates the final board.d user of ucidef_add_switch_vlan() to the new
ucidef_add_switch_ports() approach, fixing some logic errors for a few boards
along the way.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47717
Overlayfs stacking was broken in 4.1.12 but now fixed in upstream branch.
Stacking allows experimenting with configurations without the need to
reset a device to factory config.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47714
This patch adds support for the NuCom R5010UNv2.
It's a BCM6328 based board. It has an onboard BCM43217 wifi chip. For this
wifi chip looks like the brcmsmac driver isn't still supported, b43 drivers are used
for the profile of the router.
It's worth mentioning this board was affected by a bug solved with
https://dev.openwrt.org/changeset/46707
Tested-by: Angel Fontan <angel.fontan@gmail.com>
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 47697
Eth0 is attached to mac0 of the switch with a fixed link and and not to
phy4 in single phy mode, so configuring it to anything but 1000FD will
break the connection, which will happen if a only 100 Mbit capapble device
is plugged into the wan port.
Fix this by not taking the state from phy4 and just configuring a fixed link
for eth0.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 47695
This updates the iProc PCIe driver to the version currently submitted
for kernel 4.5.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47688
Broadcom submitted new SMP patches for this SoC to upstream Linux, add
them to OpenWrt.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47687
This also deactivates some workaround for erratas only seen in older
CPU cores and L2 cores not used in this SoC.
This partly reverts commit r44947.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47686
This patch is currently placed directly behind the SMP patches and has
nothing to do with SMP, move it to an other position.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47685
netis WF-2881 is an MT7621AT based router with MT7602EN, MT7612EN.
It has 128MB DDR3, 128MB SLC NAND FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.
this device only works on top of UBI.
Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons (reset button)
* ethernet switch and USB diag LEDs
* UART
* GPIOs
* sysupgrade
Tested and not working
* failsafe
Signed-off-by: YounJae Rho <luxflow@live.com>
SVN-Revision: 47619
V2:
The KD-20 also has USB 3.0.I modiy the set_irq_affinity usb 2 to set_irq_affinity ?hci_hcd 2 to bind usb 2.0&3.0 to cpu1.
Signed-off-by: Shonn Lu <countrysideboy@qq.com>
SVN-Revision: 47618
Changes since V1:
I resend this patch for current trunk.The former V1 patch is for CC branch.
Signed-off-by: Shonn Lu <countrysideboy@qq.com>
SVN-Revision: 47617
Roll back the mvebu conversion to board detection code as we need to fix
some strcutural issues first.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47597
This patch introduces support of new boards with ARC cores.
[1] Synopsys SDP board
This is a new-generation development board from Synopsys that
consists of base-board and CPU tile-board (which might have a real
ASIC or FPGA with CPU image).
It sports a lot of DesignWare peripherals like GMAC, USB, SPI, I2C
etc and is intended to be used for early development of ARC-based
products.
[2] nSIM
This is a virtual board implemented in Synopsys proprietary
software simulator (even though available for free for open source
community). This board has only serial port as a peripheral and so
it is meant to be used for runtime testing which is especially
useful during bring-up of new tools and platforms.
What's also important ARC cores are very configurable so there're
many variations of options like cache sizes, their line lengths,
additional hardware blocks like multipliers, dividers etc. And this
board could be used to make sure built software still runs on
different HW configurations.
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Jo-Philipp Wich <jow@openwrt.org>
Cc: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
SVN-Revision: 47589
Support is present in 3.19 and above as kernel commit:
fcc87a95195236b0935183361a72e4a98bf577d8
Changes to other existing patches are a result of "make target/linux/refresh".
Signed-off-by: Srdjan Rosic <srdjan.rosic@gmail.com>
Signed-off-by: Srdjan Rosic <rosic@google.com>
SVN-Revision: 47588
* use kernel buildin transfer_one_message. we only need to implement
transfer_one and set_cs function
* should support use gpio as cs pin
* deselected the spi device when setup and add debug info
* only reset device when first driver probe
Signed-off-by: Michael Lee <igvtee@gmail.com>
SVN-Revision: 47579
before spi transfer. use spi_prepare_message to setup spi hardware. it
will setup MSB, spi mode and speed
remove sys_freq member and speed check code
Signed-off-by: Michael Lee <igvtee@gmail.com>
SVN-Revision: 47578
* check clock rate, SPI mode, and word sizes
* setup spi polarity
* enable spi1 hw if need
Signed-off-by: Michael Lee <igvtee@gmail.com>
SVN-Revision: 47577
* fill struct according to the member order
* add error clean up
* set min/max spi speed. so we don't need to check again
Signed-off-by: Michael Lee <igvtee@gmail.com>
SVN-Revision: 47576
use loops_per_jiffy, spi clock speed and write bytes to get the
spi loop count. if loop to 0 than spi operation timeout.
remove usleep. we only write 1 byte to spi device. use busy loop
would be better.
Signed-off-by: Michael Lee <igvtee@gmail.com>
SVN-Revision: 47575
This patch adds the posibility to config the led behaviour of the lantiq phys
over the devicetree bindings.It patches the 0023-NET-PHY-adds-driver-for-lantiq-PHY11G
for 3.18 and 4.1. I have also added a register description overview for
applicable values. This goes to the documentation folder in the linux kernel.
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
SVN-Revision: 47566
It turned out that mtk_nand driver uses some sophisticated accounting and a
general nand code must be patched.
This patch adds required read and erase calls to a general nand code. I
used a code for re6500 released by Linksys as a reference.
All required operations (erase, write and read) are usable. However I found
that jffs2 filesystem can be created only on top of a ubi volume. I tried
to create jffs2 directly on mtd device but pages with clean markers are
became uncorrectable.
Signed-off-by: Kirill Berezin <fyiwdt@gmail.com>
SVN-Revision: 47565
This patch improves the default configuration of DWC2 on lantiq SoCs
somewhat:
* Set maximum packet count to largest allowed value by the DWC2 (511)
* Use 16-bit DMA bursts
* Divide fifo buffers more evenly
Default fifo buffer sizes from original ltq-hcd driver seem really
irrational. For example according to DWC2 data book rxfifo size of 240
will not fit even a single full length USB packet. On the other hand
non-periodic tx fifo size of 240 is more than enough to fit one complete
packet.
Change the sizes around to improve the situation and to fix some issues
especially with isochronous USB transfers.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
SVN-Revision: 47563
The hwid check was wrong, causing the AR71XX_MODEL value to end with a
space (as $hwver was unset).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47553
r47218 was missing needed changes which were accidentally
ommitted from the patch.
This should fix#20878
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 47552
When fixing the model string for WNDR3700v2 which contain a model string
followed by 0xff in r46455, the match for other versions of the WNDR3700v2
which just contain lots of 0xff broke (as the 0xff $model is checked for
is stripped off).
Fix by stripping off non-printable characters only for the actual output
string, but not for the internal matching.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47538
Removed video related kernel params that are only appropriate for the
Freescale downstream vendor kernel and not appriate for mainline linux.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 47532
The 206-ARM-imx-ventana-added-GW16083-to-device-tree.patch merged wrong in
the conversion from 3.18 to 4.1. This patch resolves that and puts the
device-tree nodes in the correct place.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 47510
Replace the ventana ubi images from a single rootfs volume containing the
rootfs as well as kernel+dtbs in the boot/ subdir to a multi-volume ubi
containing kernel+dtbs+bootscript in 'root' ubifs volume, rootfs in 'rootfs'
squasfs volume, and rootfs_data an empty ubifs volume.
At the same time move ventana image creation over to using the new
TARGET_DEVICE syntax as a cleanup.
Additionally removed FIT image creation as it is recommended that this be
done manually to produce signed FIT images if needed.
Note that a bootscript is needed for Ventana to change its default mtdparts
to rename the 2nd partition from 'rootfs' to 'ubi'. This is because there
are patches in OpenWrt kernels that try to auto-attach and auto-mount and these
get in the way if the mtd partition is named 'rootfs'.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 47508
Upstream patch: e9d6d6b62f306ba83e1441af5daf2809a6167474
Add support for the Gateworks GW5510 board featuring:
* i.MX6 SoC
* up to 512MB DDR3
* up to 2GB NAND flash
* 1x miniPCIe socket (with USB)
* HDMI out (micro-HDMI)
* HDMI in (micro-HDMI) (currently supported by only vendor kernel)
* TTL level I/O (supported by GW16111 breakout board):
* I2C
* 2x UART
* CAN
* 2x DIO (GPIO/PWM)
* USB OTG
Also add support to OpenWrt build system
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 47505
compat-wireless/backports now contains a bcm47xx_nvram.h file to
backport some of the functions in it which are used by the bcmfmac
driver. This file just checks for the kernel versions and provide an
empty implementations on older kernel versions. This is OK on most
systems, but on bcm47xx / bcm53xx systems we want to call the real
functions here. This commit removes the file from backports in our
build process like we do it with the bcma and ssb header files. Instead
we add a recent version into our kernel so all code uses only one
header file. On bcm47xx / bcm53xx the real implementations of this code
will be used.
Reported-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47467
This is based on patches from Federico Fissore <f.fissore@arduino.cc>
especially this one:
7e2976fa83
The console is running with 250000 baud which is a non standard baud
rate and needs an extra patch to be applied, I will try to get this
patch upstream or something else which accomplish the same.
Some upstream code looks like there are many different versions of this
SoC, are these only internal versions and all versions on the consumer
market are the same? I saw different GPIO configuration and flash sizes
of 8MB and 16MB?
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47451
The Arduino Yun uses a baud rate of 250000 by default. The serial is
going over the Atmel ATmega and is used to connect to this chip.
Without this patch Linux wants to switch the console to 230400 Baud.
With this patch Linux will use the configured baud rate and not some
standard one which is near by.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47450
Add access to the function2 gpio register. This probably has to be
converted into a pimux driver later on. This is needed for some setup
functions on the Arduino Yun.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47449
This automatically writes to the alternate firmware partition
(on Linksys's dual firmware layout) using code borrowed from
the WRT1900AC port.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 47434
