With this patch the dnsmasq init script manages resolv.conf if and only if
when dnsmasq will listen on 127.0.0.1#53 (is main resolver instance).
Also, resolvfile is now set irrespective of the value of noresolv.
Fixes (partially) FS#785
Signed-off-by: Paul Oranje <por@xs4all.nl>
All TP-Link TL-WR710N versions share the same machine code.
This has been working since the beginning as we don't use double-quotes
to protect spaces inside command line values. Thus, kernel interprets
'board=TL-WR710N v2' as 'board=TL-WR710N' and separate parameter 'v2'.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Keep TP-Link devices definitions in alphabetical order whenever it's
possible. Also group together similar devices or devices from the same
series.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This adds the necessary firmware layout definitions for the Archer C25.
It has an addtional partition containing some static data ("extra-para")
without which no factory flash is possible, therefore put_data() has been
added.
Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
TP-Link TL-WR942N v1 is a 2.4 GHz single-band N450 router, based on
Qualcomm/Atheros QCA9561.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x USB 2.0
- 11x LED (most are controlled by 74HC595)
- 2x button
- UART header on PCB*
* Serial console is disabled in OEM non-beta firmwares and corresponding
GPIO pins 14 and 15 are assigned to control USB1 and USB2 LEDs by
production (non-beta) U-Boot and firmware.
Currently not working:
1. USB1 and USB2 LEDs if UART RX and TX pins are assigned to their GPIOs
by some U-Boot versions.
Flash instruction under vendor GUI:
1. Download "lede-ar71xx-generic-tl-wr942n-v1-squashfs-factory.bin".
2. Go to WEB interface and perform usual firmware upgrade.
FLash instruction under U-Boot recovery mode (doesn't work in beta
firmware):
1. Setup PC with static IP "192.168.0.66/24" and tftp server.
2. Change "*-factory" image filename to "WR942v1_recovery.bin" and make
it available to download from your tftp server.
3. Press "reset" button and power up the router, wait till "WPS" LED
turns on.
Flash instruction under U-Boot, using UART (can be done only with
preinstalled UART-enabled U-Boot version!):
1. Use "tpl" to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
tftp 0x81000000 lede-ar71xx-generic-tl-wr942n-v1-sysupgrade.bin
erase 0x9f020000 +$filesize
cp.b 0x81000000 0x9f020000 $filesize
reset
Signed-off-by: Serg Studzinskii <serguzhg@gmail.com>
[minor code style fixes, extended commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Use "GL.iNet" as vendor name (based on information from the vendor, this
is registered name of the company) and align model names with official
website.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Most of the custom Build/* functions in ar71xx target are rarely used by
image building code for devices from more than one subtarget. As they
don't need to be always included, move them to corresponding *.mk files.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Some TP-Link routers (C25, C59, C60) contain a version string instead
of a binary structure in the soft_version partition.
Flashing LEDE from the original firmware's GUI, this version string
taken from the soft_ver partition of the firmware image is written to
the router's config partition.
When using tftp recovery to go back to the original Archer C25 firmware,
a version check compares that version to the version of the firmware to
be flashed.
Without proper contents in the config partition, reverting to the
original firmware fails.
Therefore, write the string "soft_ver:1.0.0\n" to that soft_ver
partition.
Signed-off-by: Jan Niehusmann <jan@gondor.com>
'non-wildcard' interfaces enables dnsmasq's '--bind-dynamic' mode. This
binds to interfaces rather than wildcard addresses *and* keeps track of
interface comings/goings via a unique Linux api.
Quoting dnsmasq's author "bind-dynamic (bind individual addresses, keep
up with changes in interface config) ... On linux, there's actually no
sane reason not to use --bind-dynamic, and it's only not the default for
historical reasons."
Let's change history, well on LEDE at least, and change the default!
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
ag71xx_ethtool_set_ringparam() will return an uninitialized value on
success.
Found-by: Coverity Scan #1330877
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Don't pass the value unconditionally to swconfig as a parameter but
instead only call reset if it is 1.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Instead of bit banging SPI to talk to the GPIO chip, use the hardware
led controllers intended for controlling the LEDs.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
split kexec-tools into two packages, kexec and kdump.
* kexec to simply execute a new kernel
* kdump is for loading and collecting debris of a crashed kernel with
support for kdump forensics.
In order to properly support booting into a crashkernel, an init script
as well as UCI configuration has been added.
As modifying the kernel cmdline is required for this to work in x86
platforms use an uci-defaults script to modify /boot/grub/grub.cfg.
To test collecting crash information, use the 'c' sysrq-trigger, ie.
echo c > /proc/sysrq-trigger
This should result in the crash kernel being executed and (depending
on the configution) dmesg and/or vmcore getting saved.
To check if the crash kernel was loaded properly, use the 'status'
command of the kdump init script.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Commit b32689afd6 added support for dhcp-script hook.
Adding dhcp-script config option results into two instances of dnsmasq being run
which triggered oom issues on platforms having low memory.
The dnsmasq dhcp-script config option will now only be added if at least one of the
dhcp, tftp, neigh hotplug dirs has a regular hotplug file or if the dhcpscript uci
config option is specified.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* Change network_get_subnet6() to sensibly guess a suitable prefix
Attempt to return the first non-linklocal, non-ula range, then attempt
to return the first non-linklocal range and finally fall back to the
previous behaviour of simply returning the first found item.
* Fix network_get_ipaddrs_all()
Instead of replicating the flawed logic appending a fixed ":1" suffix
to IPv6 addresses, rely on network_get_ipaddrs() and network_get_ipaddrs6()
to build a single list of all interface addresses.
* Fix network_get_subnets6()
Instead of replicating the flawed logic appending a fixed ":1" suffix
to IPv6 addresses, rely on the ipv6-prefix-assignment.local-address
field to figure out the proper network address.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
When git-https request a service (e.g. github) which ask for credentials
git will pass this request to the user resulting download.pl to wait for
user input. Set GIT_ASKPASS to stop asking.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Rework the network_get_ipaddr6() and network_get_ipaddrs6() functions to
fetch the effective local IPv6 address of delegated prefix from the
"local-address" field instead of naively hardcoding ":1" as static suffix.
Fixes FS#829.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
It ensures that make download can parallelize downloads, even when some
packages download the same files (e.g. gcc/initial, gcc/final)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
