Commit graph

1479 commits

Author SHA1 Message Date
John Crispin
79d02229cc ramips: move different subtarget image generation to separate makefiles to improve maintainability
- all subtarget specific defines are in their own files
- common defines left in main Makefile
- each subtarget makefile idefed with SUBTARGET
- all subtargets compile tested
- few seems to be broken/unneeded things marked with FIXME

Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 49104
2016-04-01 07:11:48 +00:00
Gabor Juhos
fc5c19f45b ramips: lzma-loader: fix O32 ABI conformance
According to the calling convention of the o32 ABI the
caller function must reserve stack space for $a0-$a3
registers in case the callee needs to save its arguments.

The assembly startup code does not reserve stack space
for these registers thus when the main C function needs
to save its arguments, that will cause a stack overflow.

Fix the assembly code to reserve stack space for the
registers to avoid that.

Untested. It seems that the lzma-loader is not used at all?

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 49062
2016-03-21 13:15:29 +00:00
John Crispin
cc82da0bc1 ramips: MiWifi-Nano - change gpios to leds, add to default build group
1) Use leds to indicate:
Red - Power
Amber - Radio On
Blue - Wifi associated
2) Add profile to default build group for MT7628 subtarget

Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com>

SVN-Revision: 49045
2016-03-20 14:41:33 +00:00
John Crispin
99414dbcf1 ramips: Add support for Xiaomi MiWiFi Nano
Xiaomi MiWiFi Nano is based on Mediatek MT7628 with 64MB ram 16MB flash

Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com>

v3  includes changes suggested by L. D. Pinney & Karl Palsson-
Eliminate en25q64 (4MB) flash chip
Alphabetization
Remove hyphen in model
Rename profile from miwifinano.mk to xiaomi.mk
Add gpios that are attached to leds

SVN-Revision: 49024
2016-03-16 09:26:48 +00:00
John Crispin
be79629259 ramips: Add support for GL-MT750
This patch adds support for GL-MT750.
GL-MT750 is powered by MT7620A and MT7610e, dual band 802.11ac, 2.4G 300Mbps and 5G 450Mbps.
It has 5 LANs, MMC interface, USB, a lot of IOs and PoE support.

SVN-Revision: 48994
2016-03-10 19:12:10 +00:00
John Crispin
be53e5a154 ramips: Add support for GL-MT300N
This patch adds support for GL-MT300N.
GL-MT300N is powered by MT7620N with 16MB flash, 64MB RAM,
2 LANs, USB, UART, GPIO and PoE support.

SVN-Revision: 48993
2016-03-10 19:12:04 +00:00
John Crispin
96ee39b184 ramips: Add support for GL-MT300A
This patches adds support for GL-MT300A.
GL-MT300A is powered by MT7620A. It has 16MB flash, 128MB RAM,
Two LANs, USB, UART and MMC daughter board.

SVN-Revision: 48992
2016-03-10 19:11:57 +00:00
John Crispin
1b9985cfe2 ramips: add support for Planex MZK-WDPR.
add support for Planex MZK-WDPR.
MZK-WDPR(MZK-WDPR-R01) is internet radio tuner.
This patch is "network board" in MZK-WDPR.
LCD board is non OpenWrt Platform.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 48968
2016-03-08 18:11:59 +00:00
Felix Fietkau
3abf5ce656 ramips: convert the remaining subtargets to 4.4
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48954
2016-03-07 17:56:53 +00:00
Felix Fietkau
f73d8fb81b ramips: fix subtarget kernel version assignment (only mt7621 is ready for now)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48953
2016-03-07 17:05:03 +00:00
Felix Fietkau
d041e8b44b ramips: add linux 4.4 support, update mt7621 subtarget to 4.4
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48951
2016-03-07 16:33:34 +00:00
John Crispin
77da9390da ramips: mt7621: fix WF-2881 for ubi split
This patch fix firmware split for WF-2881 which was previously manually partitioned.

Signed-off-by: YounJae Rho <luxflow@live.com>

SVN-Revision: 48908
2016-03-04 08:33:17 +00:00
John Crispin
9d828931f1 ramips: Add profiles for JCG routers
This patch adds profiles and support for building factory and
sysupgrade images for JHR-N805R, JHR-N825R and JHR-N926R.

Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>

SVN-Revision: 48906
2016-03-04 08:33:12 +00:00
John Crispin
43dd2b9965 ramips: Add JCG routers to base-files
This patch adds support for JHR-N805R, JHR-N825R and JHR-N926R to
various scripts in the base-files directory.

Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>

SVN-Revision: 48905
2016-03-04 08:33:09 +00:00
John Crispin
ca64f498f0 ramips: Add device tree for JCG JHR-N926R
Add a device tree for JCG JHR-N825R

This router is based on a RT3052 and has 4MB of CFI flash and 32MB of
SDRAM. As a special feature, it comes with a two digit seven segment
display that is connected to a pair of daisy-chained 74164 shift
registers that can be controlled via GPIOs.

For details, see https://wikidevi.com/wiki/JCG_JHR-N825R .

Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>

SVN-Revision: 48904
2016-03-04 08:33:06 +00:00
John Crispin
97ca4cbc94 ramips: Add device tree for JCG JHR-N825R
Add a device tree for JCG JHR-N825R

This router is based on a RT3052 and has 4MB of CFI flash and 32MB of
SDRAM. For details, see https://wikidevi.com/wiki/JCG_JHR-N825R .

Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>

SVN-Revision: 48903
2016-03-04 08:33:03 +00:00
John Crispin
73f4c3f2ab ramips: Add device tree for JCG JHR-N805R
Add a device tree for JCG JHR-N805R

This router is based on a RT3050 and has 4MB of SPI flash and 16MB of
SDRAM. For details, see https://wikidevi.com/wiki/JCG_JHR-N805R .

Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>

SVN-Revision: 48902
2016-03-04 08:33:00 +00:00
John Crispin
e4dc6acd31 ramips: Incorrect file mode change
Commit d0f5ab6d95a1 ("ramips: Added support for ZBT-826 / ZBT-1026")
incorrectly changed the mode of the ramips shell scripts from 755 to 644.
I.e., they are not excutable any more and for example devices will be left
with broken configs.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>

SVN-Revision: 48893
2016-03-03 20:24:45 +00:00
Felix Fietkau
15517811e4 ramips: enable mt76 on mt7688 by default
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48886
2016-03-02 17:40:58 +00:00
John Crispin
96eb5c6fa8 ramips: Added support for ZBT-826 / ZBT-1026
Support for these MT7620-based routers: https://wiki.openwrt.org/toh/zbt/we-826
Based on Oskari’s patches found here: https://dev.openwrt.org/ticket/19996

Signed-off-by: Jamie Stuart <jamie@onebillion.org>

SVN-Revision: 48865
2016-03-01 09:17:06 +00:00
Felix Fietkau
28458bd057 ramips: add sysupgrade support for mt7628
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48813
2016-02-28 15:46:27 +00:00
Felix Fietkau
dc6533d982 ramips: create device tree node for MT7628 WMAC in preparation for future work on driver support in mt76
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48812
2016-02-28 13:21:54 +00:00
John Crispin
f998540e80 ramips: fix GPIO names for RT5350F-OLinuXino-EVB
Hi,

the board in subject (RT5350F-OLinuXino-EVB) still ships from vendor
with a RC3 image built upon a .dts file which declares GPIO12 and GPIO14
as relay2 and relay1 respectively, as you can see from their rt5350f
branch on GitHub.

For some reason in the official stable build both the GPIOs are swapped
and the wrong names are declared in the gpio-export directive.

I'm submitting this patch which should roll back the wrong changes, so
that we get backward compatibility with any script developed on RC3
which controls the relays.

After patching correct operation is restored:

root@OpenWrt:/# cat /sys/kernel/debug/gpio
GPIOs 0-21, platform/10000600.gpio, 10000600.gpio:
 gpio-0   (button              ) in  hi
 gpio-12  (relay2              ) out lo
 gpio-14  (relay1              ) out lo

Thank you,

Signed-off-by: Lorenzo Cafaro <lorenzo@ibisco.net>

SVN-Revision: 48796
2016-02-26 08:35:35 +00:00
John Crispin
074cc7ac38 ramips: mt7620: fix failsafe switch config
As indicated in the bug tracker[1], failsafe mode is broken on at least some
devices using the mt7620 switch (and possibly mt7621). The thread explicitly
mentions the Xiaomi MiWifi, and the Nexx WT3020, and an unspecified device
using the mt7621 switch; the issue also applies to the Netgear EX2700.

The problem is that failsafe mode uses eth0, but enable_vlan is always set to 1
by the switch driver. Connecting to and/or pinging the device fails. This patch
fixes the failsafe preinit config, by making sure that vlan support is disabled.
It currently only fixes the switch config on mt7620, but might apply to the
mt7621 as well, so the patch has been designed with this in mind.

A similar (line wrapped) patch was submitted in December by Simon Peter, but never
accepted and/or discussed.

This patch applies to both Chaos Calmer and trunk.

[1] https://dev.openwrt.org/ticket/18768

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>

SVN-Revision: 48772
2016-02-25 10:14:22 +00:00
John Crispin
cb49742f99 ramips: build factory images for Netgear EX2700
This patch adds support for building factory and sysupgrade images
for the Netgear EX2700 that don't require modification of u-boot
environment variables.

The bootloader on this device expects the kernel partition to end
on a 64k block boundary. The last 64 byte of the kernel partition
must contain a valid uImage header - in the stock firmware, this is
the uImage header of the root filesystem. For this patch, we're using
the uImage header of a 0 byte partition (ex2700-fakeroot.uImage).

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>

SVN-Revision: 48771
2016-02-25 10:14:19 +00:00
Felix Fietkau
0ec9253b9d ramips: fix WSR-1166 partition table
- Fix typo in board_data partition start address
- Increase board_data partition size in order to exploit all flash size

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>

SVN-Revision: 48751
2016-02-22 08:54:32 +00:00
John Crispin
fc47eb0794 ralink: fix mt7628 ehci support
the u2_phy init was missing

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 48747
2016-02-19 16:38:04 +00:00
John Crispin
1e218001b5 ralink: unbreak port4 on mt7620
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 48746
2016-02-19 16:37:56 +00:00
John Crispin
8b38a9450b ramips: Add support for Phicomm PSG1208
This patch adds support for Phicomm PSG1208.This is a router with MT7620A SoC with 8M flash and 64M ram.
The WPS led is uesd as status_led because the power light can't be controlled with GPIO.
It seems that the 5g wifi led is connected to MT7612E and it can't be controlled with GPIO too.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>

SVN-Revision: 48721
2016-02-15 18:45:22 +00:00
John Crispin
ba53b33453 ramips: Support LEDs on D-Link DIR-860L B1
Adds the required gpio definitions.

Signed-off-by: Johannes Wienke <languitar@semipol.de>

SVN-Revision: 48715
2016-02-12 09:29:23 +00:00
John Crispin
9f9682a79b ramips: Add support for Netgear EX2700
This patch adds support for the Netgear EX2700 and builds an approriate
sysupgrade image.

What's missing is the option to build a factory image flashable via the
router's stock web interface, but this approach is hindered by the fact
that u-boot operforms an additional integrity check, which expects a
uImage header in the last 64 bytes of the "kernel" partition, which
the bootloader expects to be 960k, a size exceeded by the standard
OpenWrt kernel.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>

SVN-Revision: 48698
2016-02-12 08:29:33 +00:00
Felix Fietkau
6b73b7a8ec ramips: fix build error on oversized images by putting the dir-860l-b1 size check at the end of the chain
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48681
2016-02-08 19:18:21 +00:00
John Crispin
6801c4e33e ramips: HLK-RM04 - Enable GPIO14 for WPS button
The top half of UARTF on the HLK-RM04 is used for GPIO.

  mode 1   mode 2
   RIN     GPIO14
   DSR_N   GPIO13
   DCD_N   GPIO12
   DTR_N   GPIO11
   RXD     GPIO10
   CTS_N   GPIO09
   TXD     GPIO08
   RTS_N   GPIO07

This patch applies 3'b101 mode to UARTF:

   GPIO14
   GPIO13
   GPIO12
   GPIO11
   RXD
   CTS_N
   TXD
   RTS_N

Because the base rt5350.dtsi file forces 3'b000 mode, remove the pin setting from this file and apply it directly to the files that inherit from it (WIZFI630A.dts and WT1520.dtsi).  This change makes the rt5350.dtsi file consistent with the mt7620a.dtsi file.

Signed-off-by: John Clark <inindev@gmail.com>

SVN-Revision: 48665
2016-02-08 08:26:27 +00:00
John Crispin
7f672e66f8 rampis: HLK-RM04 - Setup I2C as GPIO
The I2C function of the RT5350 SoC on the HLK-RM04 is used for GPIO1 and GPIO2.

Take note that the I2C_SD pin is GPIO1 on the RT5350 and is exposed on the HLK-RM04 as GPIO0
Likewise the I2C_SCLK pin is GPIO2 on the RT5350 and is exposed on the HLK-RM04 as GPIO1

 group   mode 1    mode 2   hlk-rm04 pin & export
  i2c    i2c_sd    gpio1   (pin 8, hlk-rm04:gpio0)
  i2c    i2c_sclk  gpio2   (pin 9, hlk-rm04:gpio1)

reference:
  http://www.hlktech.net/product_detail.php?ProId=39
  http://cdn.sparkfun.com/datasheets/Wireless/WiFi/RT5350.pdf

Signed-off-by: John Clark <inindev@gmail.com>

SVN-Revision: 48664
2016-02-08 08:26:19 +00:00
John Crispin
480e15f2ce ramips: HLK-RM04 - Fix push button functions
The RESET button of the HLK-RM04 is connected to GPIO0, linux function 0x198
The WPS button of the HLK-RM04 is connected to GPIO14, linux function 0x211

Signed-off-by: John Clark <inindev@gmail.com>

SVN-Revision: 48663
2016-02-08 08:26:11 +00:00
John Crispin
1f26091242 ramips: HLK-RM04 - Remove power LED config
The power LED on the HLK-RM04 is hard wired to the power bus and is not under GPIO control, remove the bogus config for it.
(Note that GPIO0 is actually connected to the RESET button.)

Signed-off-by: John Clark <inindev@gmail.com>

SVN-Revision: 48662
2016-02-08 08:26:02 +00:00
Felix Fietkau
afdb24e3ae ramips: add IMAGE_SIZE to DEVICE_VARS, it is used by build templates
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48611
2016-02-01 17:41:29 +00:00
Felix Fietkau
705ddc9bb9 ramips: make tp-link firmware size errors non-fatal
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48526
2016-01-28 14:13:01 +00:00
Felix Fietkau
81e8e02289 ramips: fix image size checks for Buffalo WSR-1166 and WSR-600
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48508
2016-01-26 16:45:11 +00:00
Hauke Mehrtens
a29c7ca3d9 kernel: update kernel 4.3 to version 4.3.4
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 48498
2016-01-25 21:44:48 +00:00
Felix Fietkau
57776e68ce base-files: remove default /etc/config/network, generate it via board.d instead
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48493
2016-01-25 16:30:41 +00:00
Felix Fietkau
6f8d647778 ramips: re-enable highmem support for MT7621 now that it's fixed
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48469
2016-01-24 00:16:32 +00:00
John Crispin
f51f92d7e9 ramips: fix serial baudrate for final version of ZBT-WG2626 board
The bootloader was updated and now uses 115200 instead of 57600 baud
for the serial console. Change this also in OpenWrt's DTS, so the rate
is consistent for bootloader and linux kernel output.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 48359
2016-01-19 10:16:30 +00:00
John Crispin
9f7bbc649c ramips: HiLink HLK-RM04 image name typo (RM02 -> RM04)
The image name for the HiLink HLK-RM04 module has a typo and should read "RM04" rather than "RM02"

Signed-off-by: John Clark <inindev@gmail.com>

SVN-Revision: 48355
2016-01-19 10:15:44 +00:00
Felix Fietkau
3c3fb1dfc0 ramips: delete the broken sound driver
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48318
2016-01-18 13:40:15 +00:00
Felix Fietkau
63aa7023d8 ramips: mark kmod-sound-mtk as broken, it does not compile properly
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48317
2016-01-18 13:22:38 +00:00
Felix Fietkau
fa61e3fbba ramips: fix kernel config handling for mt7620/mt7628 sound module
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48316
2016-01-18 13:22:34 +00:00
Hauke Mehrtens
cdb83aaf5f kernel/4.3: update to version 4.3.3
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de

SVN-Revision: 48224
2016-01-12 20:52:19 +00:00
Felix Fietkau
471a567a88 ramips: do not rely on $(BIN_DIR) installed files during image build (for ubnt-erx)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48147
2016-01-06 18:39:13 +00:00
Felix Fietkau
2499a57d92 targets: add kernel image dependencies on device tree files
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48146
2016-01-06 18:39:06 +00:00