Commit graph

5 commits

Author SHA1 Message Date
Dongming Han
04d3308b62 ipq806x: add support for GL.iNet GL-B1300
This patch adds support for GL.iNet GL-B1300

Specification:
- SOC:        IPQ4028 / QCA Dakota
- RAM:        256 MiB
- FLASH:      32 MiB
- ETH:        Qualcomm Atheros QCA8075 Gigabit Switch (2 x LAN, 1 x WAN)
- USB:        1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
- WLAN1:      Qualcomm Atheros QCA4028 2.4GHz 802.11bgn 2:2x2
- WLAN2:      Qualcomm Atheros QCA4028 5GHz 802.11a/n/ac 2:2x2
- INPUT:      one reset and one WPS button
- LEDS:       3 leds: Power, WIFI(only for 2.4G currently), and one reserved
- UART:       1 x UART on PCB (3.3V, TX, RX, GND) - 115200 8N1

Installation:
Method 1:
- use serial port to stop uboot
- uboot command: run lf
Method 2:
- push down reset button and power on
- wait until three leds constantly on then release
- upgrade by uboot web at http://192.168.1.1
Note:
- the sysupgrade image need to be renamed to lede-gl-b1300.bin in both method.
- the sysupgrade image can be automatically downloaded if tftp server at
  192.168.1.2 have that file.
- the wifi led will be flashing when writing image.

Signed-off-by: Dongming Han <handongming@gl-inet.com>
2018-02-14 09:40:32 +01:00
Sven Eckelmann
86e18f6706 ipq806x: add support for OpenMesh A42
* QCA IPQ401x
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
  - 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=OM-A42
* 2T2R 5 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=OM-A42
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
  - triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
* powered only via POE
  - 802.3af POE on Ethernet 1
  - 18-24v passive POE (mode B) on Ethernet 2

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2018-01-13 08:00:14 +01:00
Mathias Kresin
c3d9fe96dc ipq806x: drop partitial supported boards
There are only artifacts for these boards in our tree and not even
partial support.

Drop teh stale files.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-13 07:33:02 +01:00
Christian Lamparter
c2d50bdeb3 ipq806x: add ipq4019 support
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John Crispin <john@phrozen.org>
2017-03-22 09:45:18 +01:00
Felix Fietkau
a531d37fab ipq806x: clean up dts patching in 4.9
Do not patch upstream files, overwrite them entirely. The upstream files
are buggy for a number of devices and this significantly simplifies the
patch structure

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: John Crispin <john@phrozen.org>
2017-03-13 13:33:51 +01:00