The TP-Link firmware uses (primary_mac-1) as MAC-address
for the 5GHz WiFi. This applies the same behaviour to LEDE.
Currently, the MAC-address is retrieved from eth1, which
does not exist on the Archer C7 v4. As a result from this,
every C7 v4 with LEDE carries the same MAC-Address on the 5GHz WiFi.
Signed-off-by: David Bauer <mail@david-bauer.net>
There are 3 ethernet ports on Y1. LAN1 on port1, LAN2 on port0 and WAN on
port4.
Use a standalone switch configuration to match this and use the switch
trigger so that LAN LED could indicate the connetction status for both
lan ports correctly.
This patch also drop the internet led configuration, because there is a
WAN led for port4 and eth0.2 isn't always used as WAN.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Because the oldest supported kernel version on the ar71xx target is 4.4,
the condition that the kernel version is smaller than 4.4.0 is always
false. Remove the obsolete check from mach-rb4xx.c to clean up the code
a bit.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Because the oldest supported kernel version on the ar71xx target is 4.4,
the condition that the kernel version is smaller than 4.2.0 is always
false. Remove the obsolete check from ag71xx_main.c to clean up the code
a bit.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Because the oldest supported kernel version on the ar71xx target is 4.4,
the condition that the kernel version is smaller than 3.15.0 is always
false. Remove the obsolete checks from the target specific source files
to clean up the code a bit.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Disable the drivers for the following ethernet switches:
Realtek RTL8306
Realtek RTL8366/8367
Marvell 88E6060 (DSA)
Marvell 88E6063 (DSA)
Also disable the phy driver for Marvell PHYs.
None of the supported RouterBOARDs are using any device
which needs these drivers.
Disable the DSA framework too, because it is not required
by the remaining switch drivers.
This reduces the compressed kernel size by ~20KB.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The Marvell 88E6063 ethernet switch driver depends on the DSA
framework. Add a 'depends on NET_DSA' statement to its Kconfig
entry to state that explicitly.
Fixes the following Kconfig warning:
warning: (NET_DSA_MV88E6060 && NET_DSA_MV88E6063) selects NET_DSA_TAG_TRAILER which has unmet direct dependencies (NET && NET_DSA)
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Building Linux 4.4 for ar71xx throws the following warnings in
drivers/net/phy/mdio-bitbang.c:
CC drivers/net/phy/mdio-bitbang.o
In file included from include/linux/irqflags.h:14:0,
from drivers/net/phy/mdio-bitbang.c:20:
drivers/net/phy/mdio-bitbang.c: In function 'mdiobb_read':
include/linux/typecheck.h:11:18: warning: comparison of distinct pointer types lacks a cast
(void)(&__dummy == &__dummy2); \
^
include/linux/irqflags.h:63:3: note: in expansion of macro 'typecheck'
typecheck(unsigned long, flags); \
^
include/linux/irqflags.h:124:3: note: in expansion of macro 'raw_local_irq_save'
raw_local_irq_save(flags); \
^
drivers/net/phy/mdio-bitbang.c:162:2: note: in expansion of macro 'local_irq_save'
local_irq_save(flags);
^
include/linux/typecheck.h:11:18: warning: comparison of distinct pointer types lacks a cast
(void)(&__dummy == &__dummy2); \
^
include/linux/irqflags.h:68:3: note: in expansion of macro 'typecheck'
typecheck(unsigned long, flags); \
^
include/linux/irqflags.h:126:39: note: in expansion of macro 'raw_local_irq_restore'
#define local_irq_restore(flags) do { raw_local_irq_restore(flags); } while (0)
^
drivers/net/phy/mdio-bitbang.c:175:2: note: in expansion of macro 'local_irq_restore'
local_irq_restore(flags);
^
drivers/net/phy/mdio-bitbang.c:159:11: warning: unused variable 'i' [-Wunused-variable]
int ret, i;
^
In file included from include/linux/irqflags.h:14:0,
from drivers/net/phy/mdio-bitbang.c:20:
drivers/net/phy/mdio-bitbang.c: In function 'mdiobb_write':
include/linux/typecheck.h:11:18: warning: comparison of distinct pointer types lacks a cast
(void)(&__dummy == &__dummy2); \
^
include/linux/irqflags.h:63:3: note: in expansion of macro 'typecheck'
typecheck(unsigned long, flags); \
^
include/linux/irqflags.h:124:3: note: in expansion of macro 'raw_local_irq_save'
raw_local_irq_save(flags); \
^
drivers/net/phy/mdio-bitbang.c:185:2: note: in expansion of macro 'local_irq_save'
local_irq_save(flags);
^
include/linux/typecheck.h:11:18: warning: comparison of distinct pointer types lacks a cast
(void)(&__dummy == &__dummy2); \
^
include/linux/irqflags.h:68:3: note: in expansion of macro 'typecheck'
typecheck(unsigned long, flags); \
^
include/linux/irqflags.h:126:39: note: in expansion of macro 'raw_local_irq_restore'
#define local_irq_restore(flags) do { raw_local_irq_restore(flags); } while (0)
^
drivers/net/phy/mdio-bitbang.c:200:2: note: in expansion of macro 'local_irq_restore'
local_irq_restore(flags);
^
These are caused by the 900-mdio_bitbang_ignore_ta_value and
901-phy-mdio-bitbang-prevent-rescheduling-during-command patches.
The first patch removes some code but it does not remove the variable
which is used by the removed code only.
The second patch adds local_irq_{save,restore} calls. The type of the
argument of these calls must be 'unsigned long', but the patch defines
the variable as 'long'.
Fix both patches to silence the warnings.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The Annex A and Annex B version are using the same (old) userspace
boardname. Update the SUPPORTED_DEVICES to allow an update from lede-17.01.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Supermicro puts "Super Server" into their product_name DMI value
for a whole slew of products, making this value about as useful
as not having been filled in at all. Instead, fall back on the
board_name instead.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
There might be other places (such as vendor-supplied preinit scripts)
where we wish to take a DMI name and clean it up in a consistent way,
so make the sed command into a function.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Rename unwinder config symbols to match upstream changes.
Refresh patches.
Update patch that no longer applies: 202-reduce_module_size.patch
Also enable CONFIG_PAGE_TABLE_ISOLATION. This feature was backported
from 4.15 to the 4.14 stable series. It is enabled by default, so enable
it in OpenWrt as well.
Compile-tested on x86/64.
Runtime-tested on x86/64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
While bumping 4.14, the kernel build failed due to missing CONFIG_KASAN
symbol. Move it to generic config instead of defining it for all arm64
and x86/64 targets.
It was only added in 4.0, so not needed in config-3.18.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The CPU sub type was set to a CPU version with FPU, but the FPU feature
was not activated before, so a soft float toolchain was created.
Activate also the FPU feature to create the correct toolchain.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This activates neon and VFPv4 support for this target. The CPU support
these feature so also use them.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since BusyBox 1.25.0 dd command supports iflag=skip_bytes which allows
skipping requested amount of bytes without reducing blocksize. Thanks to
this we can leave default blocksize and let dd work more efficiently.
On Netgear R6250 "dd skip=58 iflag=skip_bytes" can be 5 times faster
than "dd bs=58 skip=1" when extracting TRX out of CHK.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It's a device based on BCM5365P (0x5365 package 0x00). This SoC has
USB 1.1 controller but device has two USB 2.0 parts. They are handled by
PCI-based controllers: 1106:3038 UHCI and 1106:3104 EHCI.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This was broken in 7bab49fd ("lantiq: add compatible strings to dts
files"), causing for the dm200 garbled serial output during boot, and
likely other issues.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
[fix the compat string of the P2601HNFX as well]
Signed-off-by: Mathias Kresin <dev@kresin.me>
That patch fixes handling SPI messages with two writing transfers. It's
important when using e.g. by m25p80 driver which uses one transfer for
opcode and another one for data.
Thanks to that fix we can now drop m25p80 workaround patch. It means one
less hack and also a better flash writing performance as there is no
more data buf copying.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
A lot of 1U x86_64 servers have NVMe support, which is lower-power
and higher speed than SSD or CFast drives, etc. The drivers
required to make this work are trivial.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Remove a stray -Wp left in host_c_flags causing build failures for newer
4.14 versions.
Reported-by: Michael Marley <michael@michaelmarley.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Advantages:
- preserves existing partition layout on the sd-card.
Only the boot and rootfs partition will be overwritten.
Please note that sysupgrade will refuse to upgrade, if the existing
installation has an incompatible partition layout. Future changes
to the bootfs and/or rootfs partition size will likely cause breakage
to the sysupgrade procedure. In these cases, the ext4-sdcard.img.gz
will have to be written to the sdcard manually.
Please don't forget to backup your configuration in this case.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Use the values populated by the generic board detect function. The
first compatible from the device tree source file will be the board
name in userspace. The model property from the device tree source file
will be the model name.
Change the board name where used in the userspace and drop the target
specific board detect, to use the generic one.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds the compatible string for the various RPIs from
4.14 upstream.
Note: The 4.14 upstream does not include the compute modules.
If the CM* would just house the SoC, it could in theory use the
"raw" chip compatible string. However, these CM boards also come
with RAM and eMMC. So they have to have a proper comaptible.
For now, "raspberrypi,compute-module-{1|3}" will be good enough.
Note2: The original CM was renamed to CM1 when CM3 was released.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch converts all the raspberrypi images to utilize
the common metadata-based image verification.
Note: the CM1 and CM3 currently use the same "rpi-cm"
boardname.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Commit c312cef223 ("ar71xx: spi-rb4xx fix.") replaced the clk_enable() call
with clk_prepare_enable() to meet the common clock framework requirements.
However it did not change the clk_disable() call in the error patch which
thus leads to imbalance.
Fix the code by using the correct counterpart of clk_prepare_enable() in both
places.
Fixes: c312cef223 ("ar71xx: spi-rb4xx fix.")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
A few UBI messages lacks the trailing newline character which
leads to ugly lines in the bootlog like this:
[ 6.649159] UBI error: no valid UBI magic found inside mtd6[ 6.667751] Freeing unused kernel memory: 2196K
Add a newline character to the end of the messages to fix it.
After the fix the line from above looks better in the log:
[ 6.609182] UBI error: no valid UBI magic found inside mtd6
[ 6.627599] Freeing unused kernel memory: 2132K
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
A few UBI messages lacks the trailing newline character which
leads to ugly lines in the bootlog like this:
[ 6.649159] UBI error: no valid UBI magic found inside mtd6[ 6.667751] Freeing unused kernel memory: 2196K
Add a newline character to the end of the messages to fix it.
After the fix the line from above looks better in the log:
[ 6.609182] UBI error: no valid UBI magic found inside mtd6
[ 6.627599] Freeing unused kernel memory: 2132K
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
A few UBI messages lacks the trailing newline character which
leads to ugly lines in the bootlog like this:
[ 6.649159] UBI error: no valid UBI magic found inside mtd6[ 6.667751] Freeing unused kernel memory: 2196K
Add a newline character to the end of the messages to fix it.
After the fix the line from above looks better in the log:
[ 6.609182] UBI error: no valid UBI magic found inside mtd6
[ 6.627599] Freeing unused kernel memory: 2132K
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The value DSL_ChipSetHWVersion is fetched from the dsl frontend
via the dsl_control service, but not really provided by the dsl
frontend firmware and for now always "UNKNOWN".
The lantiq support told us that this information wouldn't be
provided in the foreseeable future, so let's remove this
useless "UNKNOWN" information.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Use a more appropriate compatible string. Fix the wireless led GPIO and
add the default wireless trigger. Use the wireless LED for boot state
indication as well.
Remove the GPIO pinmux for pins not exposed on the board.
Signed-off-by: Mathias Kresin <dev@kresin.me>
TP-Link TL-MR3420 v5 are simple N300 router with
5-port FE switch and non-detachable antennas.
Its very similar to TP-Link TL-WR841N V13.
Specification:
- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- USB 2.0 Port
- UART (J1) header on PCB (115200 8n1)
- 8x LED, 2x button, power input switch
Flash instruction:
The only way to flash LEDE image in mr3420v5 is to use
tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "lede-ramips-mt7628-tplink_tl-mr3420-v5-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
Move common tplink image build code into own recipe. Include the common
parts instead of including a full build recipe and overwriting former set
varaibles.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds support for the MikroTik RouterBOARD 921GS-5HPacD r2
(mANTBox 15s), an outdoor sector antenna with a built-in 802.11ac
wireless router. Additionally, it adds a new profile for devices with
>= 128 MB NAND flash and 802.11ac to the ar71xx/mikrotik subtarget.
See https://mikrotik.com/product/RB921GS-5HPacD-15S for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9558 (720 MHz)
- RAM: 128 MB
- Storage: 128 MB NAND
- Wireless: external QCA9822 802.11a/ac 2x2:2
- Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE in
- SFP: 1x host
Working:
- Board/system detection
- NAND storage detection
- Wireless
- Ethernet
- 1x user LED
- Reset button
- Sysupgrade
Untested:
- SFP cage (probably not working)
Installation:
- Boot initramfs image via TFTP and then flash sysupgrade image
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Apply code from commits 9e1bc27e6d
(ar71xx: Fix UBIFS work on Mikrotik RB95x devices) and
665bb27499 (ar71xx: fix invalid pointer
dereference in rb95x_nand_scan_fixup()) to RB92x devices too.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This patch converts all apm821xx devices to the device-tree
board-detection method. All instances of the legacy
boardnames (mbl,mr24,...) are converted to "vendor,device"
identifier.
The custom board-detection code in apm821xx.sh is removed as
it no longer serves any purpose.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch enables metadata-supported image verification
for all apm821xx supported devices. Since this method comes
with a built-in image verification tool (fwtool), the previous
image checks can be removed.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Currently, the device name handle does not include the
manufacturer. This can make it hard do differentiate
between products from different vendors that have the
same product name. As the handle is used to derive
the image name.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch rename all the DT source files in order to
match upstream's "manufacturer-device.dts" format.
Please note that the DEVICE_DTB isn't changed. This is
because the u-boot of the MyBook Live defines the
fdt_file variable to be "apollo3g/apollo3g.dtb".
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Meraki choose to use their product's codename as the main
compatible string. Mathias Kresin commented that this is
a poor choice as this will confuse the users and devs once
the device-tree compatible is used for board-detection and
possible the image name.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch appends the "apm,bluestone" or "amcc,apollo3g"
machine compatible string to the current device tree source.
Please note that unlike other archs the PPC DT code does
not regard the machine's compatible string as a priority
list. This is explained in the kernel's usage-model.txt as follows:
"PowerPC uses a slightly different scheme where it calls the .probe()
hook from each machine_desc, and the first one returning TRUE is used.
However, this approach does not take into account the priority of the
compatible list, and probably should be avoided for new architecture
support."
For this reason, the "apm,bluestone" compatible string can't be
added to the WNDR4700. As otherwise the target specific pci
fix-up code will get ignored and this causes the ath9k WIFI
to not get initialized.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch sets the BOARD_NAME variable on each affected
apm821xx device. The existing DEVICE_PROFILE and
DEVICE_NAME assignments are deprecated as they no longer
serve any purpose.
The BOARD_NAME variable is used by the sysupgrade-tar
method to specifiy a directory overwrite for the
sysupgrade-$dir directory in the generated tar file.
Keeping the original boardname in this context will be
necessary for targets that utilize the sysupgrade-tar
method. Otherwise, sysupgrade on an previous installation
will not recognize the newly generated images.
This step is necessary since an upcoming patch realigns
the existing shortname for a device with a proper
"manufacturer_device" identifier.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The commit 87b668765e
("image: when using the new image build code, gzip ext4 images by default")
forced that all targets that select the ext4 as the root filesystem
to always compress the generated rootfs. This is fine, but this method
doesn't not allow to append the metadata on a per-target base.
Therefore this patch changes the rootfs image production rule to generate
the gzip step manually. This way the metadata can be appended at a later
date.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
"PandoraBox" is not the name of the manufacturer, it's a firmware made by
the manufacturer actually. Their official English name is "D-Team".
PBR-M1 is the only one they use "PandoraBox" as a brand name. Their other
products are using "Newifi" as their trademark (including Y1 and Y1S which
used to be OEM products for Lenovo).
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Previously Newifi D2 could only use PandoraBox M1's firmware.
It works fine, but LED GPIO is different.
As a result, a separated DTS file for this device should be implemented.
Hardware spec:
* CPU: MTK MT7621A
* RAM: 512MB
* ROM: 32MB SPI Flash
* WiFi: MTK MT7603+MT7612
* Button: 2 buttons (reset, wps)
* LED: 3 single-color LEDs (USB, WiFi 2.4GHz, WiFi 5GHz) &
2 dual-color LEDs (Power, Internet)
* Ethernet: 5 ports, 4 LAN + 1 WAN
Installation method:
Same as Newifi D1, users may need to request unlock code from the device
manufacturer. Otherwise, a SPI flash programmer may be necessary to get
the firmware flashed. After the device is unlocked, press and hold reset
button before power cable plugs in. Then go to http://192.168.1.1 to
upload and flash the firmware package.
Signed-off-by: Jackson Ming Hu <huming2207@gmail.com>
The VAR11N-300 is a tiny wireless-N device with a hardwired Ethernet
cable, one extra Ethernet port, and an internal antenna, based on the
MediaTek MT7620n chipset.
Specs:
- MT7620n WiSoC @ 600MHz
- 32 MB SDRAM
- 4 MB SPI flash
- 2T2R 2.4GHz WiFi-N
- 1 attached 10/100 Ethernet cable (LAN)
- 1 10/100 Ethernet port (WAN)
- 1 attached USB / barrel 5vdc power cable
- 5 LEDs (see notes below)
- 1 reset button
- 1 UART (3 pads on board)
Installation:
The stock firmware does not support uploading new firmware directly,
only checking the manufacturer's site for updates. This process may be
possible to spoof, but the update check uses some kind of homebrew
encryption that I didn't investigate. Instead, you can install via a
backdoor:
1. Set up a TFTP server to serve the firmware binary
(lede-ramips-mt7620-var11n-300-squashfs-sysupgrade.bin)
2. Factory reset the device by holding the reset button for a few
seconds.
3. Open the web interface (default IP: 192.168.253.254)
4. Log in with the "super admin" credentials: username `vonets`,
password `vonets26642519`.
5. On the "Operative Status" page, click the text "System Uptime", then
quickly click the uptime value.
6. If successful, an alert dialog will appear reading "Ated start", and
the device will now accept telnet connections. If the alert does not
appear, repeat step 5 until it works (the timing is a bit tricky).
7. Telnet to the device using credentials "admin / admin"
8. Retrieve the firmware binary from the tftp server: `tftp -l lede.bin
-r lede-ramips-mt7620-var11n-300-squashfs-sysupgrade.bin -g
<tftp-server-ip>`
9. Write the firmware to flash: `mtd_write write lede.bin /dev/mtd4`
10. Reboot
Tested:
- LAN / WAN ethernet
- WiFi
- LAN / WAN / status LED GPIOs (see notes below)
- Reset button
- Sysupgrade
Notes:
LEDs:
The board has 5 LEDs - two green LEDs for LAN / WAN activity, one blue
LED for WiFi, and a pair of "status" LEDs connected to the same GPIO
(the blue LED lights when the GPIO is low, and the green when it's
high). I was unable to determine how to operate the WiFi LED, as it
does not appear to be controlled by a GPIO directly.
Recovery:
The default U-boot installation will only boot from flash due to a
missing environment block. I generated a valid 4KB env block using
U-boot's `fw_setenv` tool and wrote it to flash at 0x30000 using an
external programmer. After this, it was possible to enter the U-boot
commandline interface and download a new image via TFTP (`tftpboot
81b00000 <image-filename>`), but while I could boot this image
sucessfully (`bootm`), writing it to flash (`cp.linux`) just corrupted
the flash chip. The sysupgrade file can be written to flash at 0x50000
using an external programmer.
Signed-off-by: Andrew Crawley <acrawley@gmail.com>
Add a helper variable which contains the boardname separated from the
vendor name. It allows to switch to a device tree compatible string
based boardname, by keeping the $board:colour:function syntax in
scripts handling/adding config for LEDs.
Boards not using the device tree compatible string as based boardname
are unaffected by the change, since none of them uses a comma in the
boardname.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use <manufacturer>_<modelname> as image name for board using the
devicetree compat string as boardname.
Replace the underline of the device define, to keep the SUPPORTED_DEVICES
in sync with a devicetree compat string based boardname.
Override the default SUPPORTED_DEVICES for board which are having an
userspace boardname with an underline.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The LinkIt Smart 7688/LinkIt Smart 7688 Duo are identical beside the
extra ATmega32U4 - accessible via UART - on the the Duo.
Since all relevant hardware is identical, drop the Duo special handling
in userspace.
Signed-off-by: Mathias Kresin <dev@kresin.me>
If we need to set the initial output value to GPIOF_OUT_INIT_HIGH (1) to
enable something, the pin is ACTIVE_HIGH. The same applies to
GPIOF_OUT_INIT_LOW (0) and ACTIVE_LOW.
Signed-off-by: Mathias Kresin <dev@kresin.me>
In the stock firmware both eth0 and eth1 are set to br-lan,
add this behavior to our images.
Fixes: FS#1084
Signed-off-by: Marty E. Plummer <hanetzer@protonmail.com>
The status led part was missed when changing the board name to *-nor.
Fixes: e12c72bb52 ("brcm63xx: Add Sercomm AD1018 support")
Reported-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Use <manufacturer>_<modelname> as image name.
Use the BOARD_NAME variable to ensure that the former used boardname is
still used as the subdirectory name for the sysupgrade-tar image, to
not break sysupgrade from earlier versions.
While at it, normalise the image filenames by using only lower case
characters and bin as file extension for sysupgrade images.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the first compatible string as board name in userspace. Add the new
board name as well as the former used board name to the image metadata
to keep compatibilty with already deployed installations.
Don't add the former used boardname for boards which exists only in
master or evaluation boards.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This adds basic support for kernel 4.14, this was tested in qemu only.
The subtarget configuration was refresh with kernel 4.14 and the
options needed to make it compile on kernel 4.9 were added manually.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In kernel 4.14 kmod-bluetooth depends on kmod-crypto-ecdh, add
kmod-crypto-ecdh to LEDE.
Both packages also depend on the kmod-crypto-kpp package. To build this
we have to fix the dependency of CRYPTO_ECDH which has a typo.
This patch is already accepted upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds initial support for kernel 4.14 based on the patches for
kernel 4.9.
In the configuration I deactivated some of the new possible security
features like:
CONFIG_REFCOUNT_FULL
CONFIG_SLAB_FREELIST_HARDENED
CONFIG_SOFTLOCKUP_DETECTOR
CONFIG_WARN_ALL_UNSEEDED_RANDOM
And these overlay FS options are also deactivated:
CONFIG_OVERLAY_FS_INDEX
CONFIG_OVERLAY_FS_REDIRECT_DIR
I activated this:
CONFIG_FORTIFY_SOURCE
CONFIG_POSIX_TIMERS
CONFIG_SLAB_MERGE_DEFAULT
CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED
I am not sure if I did the porting correct for the following patches:
target/linux/generic/backport-4.14/020-backport_netfilter_rtcache.patch
target/linux/generic/hack-4.14/220-gc_sections.patch
target/linux/generic/hack-4.14/321-powerpc_crtsavres_prereq.patch
target/linux/generic/pending-4.14/305-mips_module_reloc.patch
target/linux/generic/pending-4.14/611-netfilter_match_bypass_default_table.patch
target/linux/generic/pending-4.14/680-NET-skip-GRO-for-foreign-MAC-addresses.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Just refresh the kernel configuration, some options are removed because
they are now in the generic kernel configuration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These are taken from the x86 target and should make support kernel 4.9
and 4.14 in the x86 target easier.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cover temperature sensors for all mainstream 64-bit processors, including
AMD 10h and 15h families, Intel iCore, Xeon, Atom, and Via Nano. Also
add CPUID support for user-space applications to detect CPU type.
Include the on-chip sensors for 64-bit CPU's in the generic profile
in case someone builds a 32-bit kernel to run on a Xeon SoC, etc.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Backport the mdio-bus reset gpio support from 4.12 and use it instead
of toggling the reset ourself.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Add support for the Sercomm AD1018 router
This a BCM6328 based board, 128 MB RAM, 128 MiB NAND flash,
with an onboard BCM43217 wifi, 4 ethernet ports and 1 USB
host port (not soldered). The board also has an FXS chip (Si32177)
connected via SPI (SS2#), without support in LEDE.
Since NAND flash chips aren't still supported in brcm63xx, the
support is for now added to work only with SPI flash chips. Therefore
hardware modding, soldering a new SPI flash chip, is required
to make the board work with LEDE (tested and working OK).
The flash at dts is intentionally left without partitioning to let
the user choose a NOR chip of any size (8, 16 or 32 MB).
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
[jonas.gorski: renamed ad1018 to ad1018-nor to signify the modification]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Since Linux 4.6, mtd->priv no longer points to the NAND specific
structure. Under 4.9 it contains NULL, thus using it to access
chip->options causes an invalid pointer dereference (FS#1200).
Update the code to use the mtd_to_nand() helper under 4.9 to obtain
the address of the chip specific data.
Fixes: 7bbf4117c6 ("ar71xx: Add kernel 4.9 support")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Since Linux 4.6, mtd->priv no longer points to the NAND specific
structure. Under 4.9 it contains NULL, thus using it to access
the fields of the nand_chip structure causes an invalid pointer
dereference.
Update the code to use the mtd_to_nand() helper under 4.9 to obtain
the address of the chip specific data.
Compile tested only.
Fixes: 7bbf4117c6 ("ar71xx: Add kernel 4.9 support")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Tested-by: Christian Lamparter <chunkeey@gmail.com>
When mtdsplit_minor.c is compiled under Linux 4.4, the compiler
drops the following warning:
CC drivers/mtd/mtdsplit/mtdsplit_minor.o
drivers/mtd/mtdsplit/mtdsplit_minor.c:106:14: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types]
.parse_fn = mtdsplit_parse_minor,
^
drivers/mtd/mtdsplit/mtdsplit_minor.c:106:14: note: (near initialization for 'mtdsplit_minor_parser.parse_fn')
The second parameter of the parser function must not have a 'const'
qualifier in 4.4. The 001-mtdsplit_backport.patch removes the qualifier
from other partition parsers. Update it to handle mtdsplit_minor.c as
well.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
This reverts commit 256990cbc0.
this commit caused a compile error
"TL_WR1043_V5_GPIO_LED_WANORANGE" is undefined.
Signed-off-by: John Crispin <john@phrozen.org>
Add missing definitions for the orange WAN LED on the TL-WR1043N(D) v4 and
v5. Minor format correction on a constant for consistency.
Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
This patch fixes the switch port numbering on Mikrotik RB951Ui-2nD (hAP).
Also fixes the switch port numbering shown on LuCI for Mikrotik RB493G.
Signed-off-by: João Chaínho <joaochainho@gmail.com>
Advantages:
- preserves existing partition layout. On the hard-drive.
Only the boot and rootfs partition will be overwritten.
Disadvantages:
- The upgrade process takes much longer to run.
from 2-3 seconds to 15-25 seconds.
Please note that sysupgrade will refuse to upgrade, if the existing
installation has an incompatible partition layout. Future changes
to the bootfs and/or rootfs partition size will likely cause breakage
to the sysupgrade procedure. In these cases, the ext4-rootfs.img.gz
has to be written manually onto the disk. Please don't forget to backup
your configuration in this cases.
Note2: This patch requires
"base-files: upgrade: make get_partitions() endian agnostic"
Note3: If your current installation does not host the two
changes, sysupgrading will wipe the existing partition
layout. Don't forget to backup your data!
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Please note that users with a Netgear WNDR4700
will need to update the device-tree partition
manually.
For instructions, please refere to commit 49856a4bb5
("apm821xx: make it possible to update the dtb partition on the WNDR4700")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Lantiq and IPQ806X (which includes IPQ40XX) both define the
same custom function {ipq806x|lantiq}_get_dt_led.
This patch moves the function into the base-file package at
lib/functions/leds.sh to make it more accessible for other
targets as well.
Cc: Mathias Kresin <dev@kresin.me>
Cc: John Crispin <john@phrozen.org>
Cc: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The bcm6368 pinctrl driver passed the wrong variable to
devm_regmap_field_alloc, causing it to blow up when later trying to
access the field.
Fixes#1211.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
For an unknown reason gcc tries to link in crti.o when building with a
glibc toolchain (this does not happen with other targets). Prevent this
by telling gcc explicitly to not do that.
Fixes the following build error:
/home/jonas/git/lede/staging_dir/toolchain-mips_24kc_gcc-5.5.0_glibc/lib/gcc/mips-openwrt-linux-gnu/5.5.0/../../../../mips-openwrt-linux-gnu/lib/crti.o: In function `_init':
(.init+0x18): relocation truncated to fit: R_MIPS_GOT16 against `__gmon_start__'
/home/jonas/git/lede/staging_dir/toolchain-mips_24kc_gcc-5.5.0_glibc/lib/gcc/mips-openwrt-linux-gnu/5.5.0/../../../../mips-openwrt-linux-gnu/lib/crti.o: In function `_init':
(.init+0x28): relocation truncated to fit: R_MIPS_CALL16 against `__gmon_start__'
collect2: error: ld returned 1 exit status
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
This will avoid some conflicts when doing a git rebase or merge,
specially when adding support to a new device.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
[drop brcm47xx changes which rename the images]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Recent RouterBOOT version (at least version 3.41 on RB911G-5HPacD)
use "Board=" kernel parameter instead of "board=" to pass the board
name to the kernel. Due to this change the board detection code is
not working on the devices shipped with the new RouterBOOT version.
Because the kernel is unable to identify these boards they become
unusable despite that they are supported by the current code.
Update the prom_init code to convert the 'Board' kernel parameter to
'board'. After this change, the board detection works also with the
new RouterBOOT versions.
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
The target name does not need to included a revision
if all revisions are supported.
This target supports all revisions (v1, v2, v2.1).
Signed-off-by: Moritz Warning <moritzwarning@web.de>
[Keep the version numbers in the device title, it doesn't harm]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Remove the WW suffix, everything without a region suffix is world wide
anyway.
While at it, normalise the image filenames by using only lower case
characters.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Users are confused which image type they should use and there are more
drawbacks than adavantages in using a r/w ubifs rootfs in constrast to
a read-only squashfs rootfs like:
- less available free flash space due to better compression of squashfs
images
- no support for factory reset due to r/w filesystem
- possibility to break failsafe due to r/w filesystem
Therefore, drop support for r/w ubifs rootfs images.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The boardname isn't used any longer to find the subdirectory in the
sysupgrade tar archive, which makes this override useless.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Qualcomm claims this reduces cache misses. Original commit message below:
From: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Date: Tue, 11 Jun 2013 12:18:46 -0500
Subject: [ag71xx] reduce NAPI weight
In an attempt to increase our cache warmth, we are decreasing NAPI.
This increases the warmth of the reused SKBs.
Signed-off-by: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The motivation for this was misguided. It turns out tuning the NAPI weight could be useful for testing purposes. Therefore reverting.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This commit fixes LAN Port 1 not transferring data in case no
other LAN Port has active link-state on TP-Link Archer C58/C59.
Signed-off-by: David Bauer <mail@david-bauer.net>
This is a variant of the MT7620N-based Asus routers.
Specifications:
- MT7620N (580 MHz)
- 32 MB RAM
- 8 MB Flash
- 5x 10/100Mbps Ethernet (built-in switch)
- 2.4 GHz WLAN
- 2x external, non-detachable antennas
- UART (J2) header on PCB (115200 8n1)
Flash instructions:
1. Configure PC with static IP 192.168.1.75/24
2. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds. All 4 LEDs will
start to blink, which is when the router will accept firmware files via TFTP.
No known limitations on firmware filenames, just send it with a TFTP client
to 192.168.1.1.
3. Router will download file from server, write it to flash and reboot.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This commit adds missing the GPIO key used as reset button.
Nexx WT1520 has a GPIO key for factory reset, but it's not defined in
WT1520.dtsi and cannot use it.
Drop the UART (full) from the device tree source file, it was never
used for this board. Adjust the kernel bootargs accordingly.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[add note about dropped UART (full) to the commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
There are multiple problems on the A64 SoC with the older drivers which
are fixed in the upstream kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add pinmuxes defined by some board which are including the dtsi files
to the dtsi files itself. Allows to reduce duplication.
Signed-off-by: Mathias Kresin <dev@kresin.me>
According to the datasheet the REFCLK pin is shared with GPIO#37 and
the PERST pin is shared with GPIO#36.
While at it fix a typo inside the pinmux setup code. The function is called
refclk and not reclk.
Update device tree source files accordingly.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add kmod-sound-core, it is a dependency of kmod-sound-mt7620 and will
not be autoselected.
Remove kmod-i2c-core, it will be autoselected by kmod-i2c-ralink.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Setting the pins of the UARTF group to GPIO+I2S at the time the I2C
driver loads is to late for the wps GPIO button.
The gpio-keys driver fails to load since the pin used by the wps button
is not yet set to GPIO. The wps button with the rfkill keycode is
essential for this wireless only board.
Add the missing sound and I2C kernel modules corresponding to the
device nodes.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The advantage is that we don't have to specify max TRX size anymore and
otrx doesn't allocate a buffer of that size. It saves us allocating
32 MiB for every image we generate.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Backported devicetree from Kernel 4.13 with some additions
to enable Ethernet and WiFi module
The following features are working:
- Ethernet
- WiFi
- eMMC and microSD slot
- USB ports
The following features are not working:
* Bluetooth
NanoPi M1 Plus key features
- SoC: Allwinner H3, Quad-core Cortex-A7@1.2GHz
- RAM: 1GB DDR3
- eMMC: 8GB
- microSD slot
- Ethernet 10/100/1000M
- Wifi: AP6212
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
D-Link DIR-330 is clone of ASUS WL500GP2, by default conf the WAN port is
eth1, it's not working cus eth1 not soldered and wan port function
performs 5th port of the switch.
Signed-off-by: Antony Black <gtrtfm@gmail.com>
Currently local TCP performance on wifi devices can be limited because
the TSQ (TCP Small Queues) code is tuned for wired ethernet latencies.
With this patch drivers can increase the amount of local buffering to
allow TCP to trigger larger aggregation sizes
This commit is modified from the upstream version to allow #ifdef based
backport feature detection
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a variant of the ZBT WG3526 with a few minor modifications.
The wifi chips are swapped, and there is no GPIO controllable status
LED. There is also no SATA port.
Specifications:
- MT7621AT (880 MHz)
- 512 MB RAM
- 16 MB Flash (SPI NOR)
- 5x 1Gbps Ethernet (built-in switch)
- MT7612E 802.11ac 5 GHz WLAN
- MT7603E 802.11n 2.4 GHz WLAN
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The IRQ controller can only set the affinity to a single CPU. Update the
mask in the controller data.
Suggested-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
TP-Link TL-WR802N v1 and v2 are set up with almost same configuration in
the mach-files. Merge the mach-files of these devices.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
TP-Link TL-WR1043N v5 appears to be identical to the TL-WR1043ND v4,
except that the USB port has been removed and there is no longer a
removable antenna option.
The software is more in line with the Archer series in that it uses a
nested bootloader scheme.
Specifications:
- QCA9563 at 775 MHz
- 64 MB RAM
- 16 MB flash
- 3 (non-detachable) Antennas / 450 Mbit
- 1x/4x WAN/LAN Gbps Ethernet (QCA8337)
- reset and Wi-Fi buttons
Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
The TL-WA901ND v5 has the same hardware as v4, although the PCB has
a different layout. Installation from factory is done via TFTP.
(rename -factory image to wa901ndv4_tp_recovery.bin for tftp)
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
This patch adds support for the MikroTik RouterBOARD mAP 2nD
https://mikrotik.com/product/RBmAP2nD
Specifications:
- SoC: Qualcomm QCA9531 (650 MHz)
- RAM: 64 MB
- Storage: 16 MB NOR SPI flash
- Wireless: builtin QCA9531, 2x2:2
- Ethernet: 2x100M (802.3af/at POE in and passive POE out on ETH2)
- USB: microUSB type AB port
This patch adds missing code to fully support mAP. Machfile already
contained configuration for mAP 2nD, but device specific configuration
like LEDs etc., was missing.
Note: The POE LED works but doesn't turn on when POE passthrough is
enabled, despite being configured with GPIO trigger.
Installation
1. Login to the Mikrotik WebUI to backup your licence keys
2. Setup a DHCP/BOOTP server with:
- DHCP-Option 66 (TFTP server name) pointing to a local TFTP
server within the same subnet of the DHCP range
- DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
of the to be booted image
3. Connect the port labeled internet to your local network
4. Keep the reset button pushed down and power on the board
The board should load and start the initramfs image from the TFTP
server. Login as root/without password to the started LEDE via SSH
listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE.
Revert to RouterOS
Use the "rbcfg" package on in LEDE:
- rbcfg set boot_protocol bootp
- rbcfg set boot_device ethnand
- rbcfg apply
Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.
Click on install again.
In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Ubiquiti UniFi APs just have eth0. Until now, the setup script fell
through to the default case and configured the (not present) eth1 as
WAN with DHCP.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
This patch adds support for the MikroTik RouterBOARD wAP
https://mikrotik.com/product/RBwAP2nD
Specifications:
- SoC: Qualcomm QCA9533 (650 MHz)
- RAM: 64 MB
- Storage: 16 MB NOR SPI flash
- Wireless: built-in QCA9533, 2x2:2
- Ethernet: 1x100M (802.3af/at POE in)
This patch adds missing code to fully support wAP. Machfile already
contained configuration for wAP 2nD but device specific configuration
like LEDs etc. was missing.
Installation:
1. Login to the Mikrotik WebUI to backup your licence keys
2. Setup a DHCP/BOOTP server with:
- DHCP-Option 66 (TFTP server name) pointing to a local TFTP
server within the same subnet of the DHCP range
- DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
of the to be booted image
3. Connect the port labeled internet to your local network
4. Keep the reset button pushed down and power on the board
The board should load and start the initramfs image from the TFTP
server. Login as root/without password to the started LEDE via SSH
listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE.
Revert to RouterOS
Use the "rbcfg" package on in LEDE:
- rbcfg set boot_protocol bootp
- rbcfg set boot_device ethnand
- rbcfg apply
Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.
Click on install again.
In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Wallys DR342 is a 5 GHz, 2T2R AP/CPE board based on Atheros AR9342.
Short specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 1x Gbps Ethernet (AR8035) with passive PoE support (24-56 V)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 5 GHz with external FEM (SKY85728-11), up to 30 dBm
- 2x MMCX connectors
- miniPCIe connector with PCIe and USB 2.0 buses
- optional miniSIM slot
- 7x LED, 1x button
- UART, (E)JTAG and LED headers
- 1x DC jack for main power (12-56 V)
Flash instruction (do it under U-Boot, using UART):
1. tftp 0x82000000 lede-ar71xx-generic-dr342-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
UniElec U7628-01 is a router platform board based on MediaTek MT7628AN.
The device has the following specifications:
- MT7628AN (580MHz)
- 64/128/256 MB of RAM (DDR2)
- 8/16 MB of flash (SPI NOR)
- 5x 10/100 Mbps Ethernet (MT7628 built-in switch)
- 1x 2T2R 2.4 GHz Wi-Fi (MT7628)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses)
- 1x miniSIM slot
- 1x microSD slot
- 1x USB 2.0 port
- 7x single-color LEDs (GPIO-controlled)
- 1x bi-color LED (green GPIO-controlled, red -> LED_WLAN# in miniPCIe)
- 1x reset button
- 1x UART header (4-pins)
- 1x SDXC/GPIO header (10-pins, connected with microSD slot)
- 1x DC jack for main power (12 V)
The following has been tested and is working:
- Ethernet switch
- miniPCIe slot (tested with modem and Wi-Fi card)
- miniSIM slot
- sysupgrade
- reset button
- USB 2.0 port*
Due to a missing driver (MMC over GPIO) this is not supported:
- microSD card reader
* Warning:
USB buses in miniPCIe and regular A-type socket are connected together,
without any proper analog switch or USB HUB.
Installation:
This board might come with a different firmware versions (MediaTek SDK,
PandoraBox, Padavan, etc.). If your board comes with PandoraBox, you can
install LEDE using sysupgrade. Just SSH to the router and perform forced
sysupgrade (due to a board name mismatch). The default IP of this board
should be: 192.168.1.1 and username/password: root/admin. In case of a
different firmware, you can use web based recovery described below.
Use the following command to perform the sysupgrade (for the 128MB
RAM/16MB flash version):
sysupgrade -n -F lede-ramips-mt76x8-u7628-01-128M-16M-squashfs-sysupgrade.bin
Recovery:
This board contains a Chinese, closed-source bootloader called Breed
(Boot and Recovery Environment for Embedded Devices). Breed supports web
recovery and to enter it, you keep the reset button pressed for around
5 seconds during boot. Your machine will be assigned an IP through DHCP
and the router will use IP address 192.168.1.1. The recovery website is
in Chinese, but is easy to use. Click on the second item in the list to
access the recovery page, then the second item on the next page is where
you select the firmware. In order to start the recovery, you click the
button at the bottom.
SDXC/GPIO header (J3):
1. SDXC_D3 / I2C_SCLK
2. SDXC_D2 / I2C_SD
3. SDXC_D1 / I2S_DI
4. SDXC_D0 / I2S_WS
5. SDXC_CMD / I2S_CLK
6. SDXC_CLK / GPIO0
7. SDXC_CD / UART_RXD1
8. UART_TXD1
9. 3V3
10. GND
Other notes:
1. The board is available with different amounts of RAM and flash. We
have only added support for the 128/16 MB configuration, as that seems
to be the default. However, all the required infrastructure is in place
for making support for the other configurations easy.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
UniElec U7621-06 is a router platform board based on MediaTek MT7621AT.
The device has the following specifications:
- MT7621AT (880 MHz)
- 256/512 MB of RAM (DDR3)
- 8/16/32/64 MB of FLASH (SPI NOR)
- 5x 1 Gbps Ethernet (MT7621 built-in switch)
- 1x ASMedia ASM1061 (for mSATA and SATA)
- 2x miniPCIe slots (PCIe bus only)
- 1x mSATA slot (with USB 2.0 bus for modem)
- 1x SATA
- 1x miniSIM slot
- 1x microSD slot
- 1x USB 3.0
- 12x LEDs (3 GPIO-controlled)
- 1x reset button
- 1x UART header (4-pins)
- 1x GPIO header (30-pins)
- 1x FPC connector for LEDs (20-pin, 0.5 mm pitch)
- 1x DC jack for main power (12 V)
The following has been tested and is working:
- Ethernet switch
- miniPCIe slots (tested with Wi-Fi cards)
- mSATA slot (tested with modem and mSATA drive)
- miniSIM slot
- sysupgrade
- reset button
- microSD slot
Installation:
This board might come with a different firmware versions (MediaTek SDK,
PandoraBox, Padavan, etc.). If your board comes with PandoraBox, you can
install LEDE using sysupgrade. Just SSH to the router and perform forced
sysupgrade (due to a board name mismatch). The default IP of this board
should be: 192.168.1.1 and username/password: root/admin. In case of a
different firmware, you can use web based recovery described below.
Use the following command to perform the sysupgrade (for the 256MB
RAM/16MB flash version):
sysupgrade -n -F lede-ramips-mt7621-u7621-06-256M-16M-squashfs-sysupgrade.bin
Recovery:
This board contains a Chinese, closed-source bootloader called Breed
(Boot and Recovery Environment for Embedded Devices). Breed supports web
recovery and to enter it, you keep the reset button pressed for around
5 seconds during boot. Your machine will be assigned an IP through DHCP
and the router will use IP address 192.168.1.1. The recovery website is
in Chinese, but is easy to use. Click on the second item in the list to
access the recovery page, then the second item on the next page is where
you select the firmware. In order to start the recovery, you click the
button at the bottom.
LEDs list (top row, left to right):
- LED_WWAN# (connected with pin 42 in LTE/mSATA slot)
- Power (connected directly to 3V3)
- CTS2_N (GPIO10, configured as "status" LED)
- TXD2 (GPIO11, configured as "led4", without default trigger)
- RXD2 (GPIO12, configured as "led5", without default trigger)
- LED_WLAN# (connected with pin 44 in wifi0 slot)
LEDs list (bottom row, left to right):
- ESW_P0_LED_0
- ESW_P1_LED_0
- ESW_P2_LED_0
- ESW_P3_LED_0
- ESW_P4_LED_0
- LED_WLAN# (connected with pin 44 in wifi1 slot)
Other notes:
1. The board is available with different amounts of RAM and flash. We
have only added support for the 256/16 MB configuration, as that seems
to be the default. However, all the required infrastructure is in place
for making support for the other configurations easy.
2. The manufacturer offers five different wireless cards with MediaTek
chipsets, based on MT76x2, MT7603 and MT7615. Images of the board all
show that the miniPCIe slots are dedicated to specific Wi-Fi cards.
However, the slots are generic.
3. All boards we got access to had the same EEPROM content. The default
firmware reads the Ethernet MAC from offset 0xe000 in factory partition.
This offset only contains 0xffs, so a random MAC will be generated on
every boot of the router. There is a valid MAC stored at offset 0xe006
and this MAC is shown as the WAN MAC in the bootloader. However, it is
the same on all boards we have checked. Based on information provided
by the vendor, all boards sold in small quantities are considered more
as samples for development purposes.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
This increases kernel partition size and fixes rootfs (file-system)
partition size on TP-Link RE450 v1. Also, while we are at it, switch
from statically defined kernel and rootfs partitions in kernel cmdline
to "tplink-fw" mtd splitter.
Fixes: FS#1072.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This patch increases kernel partition size and re-enables image
generation for below TP-Link boards:
- archer-c58-v1
- archer-c60-v1
- tl-wr902ac-v1
- tl-wr942n-v1
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[commit message and title reworded]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
There was a typo in module.mk for pfe module autoload.
This patch is to fix this and remove useless rc.local
which was for loading pfe module.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The QorIQ FRDM-LS1012A Board is an ultra-low-cost
development platform for QorIQ LS1012A Series Network
Processors built on ARM Cortex-A53 processor.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to add PPA (The Primary Protected Application)
package and also enable it for all layerscape devices.
LSDK github provides ppa source code git tree, but it
only could be compiled with 64-bit toolchain. For 32-bit
devices, there was no method to use it.
https://github.com/qoriq-open-source/ppa-generic
This patch is to directly use a private ppa binary tree for
both 32-bit and 64-bit devices.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to use ppfe git tree on LSDK github
instead of private git tree, and support the latest
ppfe on ls1012ardb.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Some new options were introduced by kernel patches.
And some options should be removed/added.
The config-4.9 should be updated accordingly.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Updated kernel patches to align layerscape kernel
with latest LSDK linux (LSDK-17.09-update-103017-V4.9 tag).
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Default profile had to enable many packages for all devices
support. This made these packages still enabled when built
for single device. This patch is to remove default profile.
For multiple devices build, it's proper to build with multiple
devices profile.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
A previous patch disaggregated kernel patch 601 intending to
reverse the ndo_get_stats64 change, but it also dropped
many other changes without a reason. This caused build issue
for layerscape. This patch is to fix that with below steps.
1. Reversed patch "1c4415a layerscape: reverse changes to ndo_get_stats64",
but kept kernel patch 701 which was a proper fix.
2. Reversed the ndo_get_stats64 change in kernel patch 601.
3. Renamed patch 601 (net patch) to 202 (core-linux patch). Maybe it's
more proper.
Fixes: 1c4415a679 ("layerscape: reverse changes to ndo_get_stats64")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
On the Asus RT-N16, the ports are not mapped the in the same way as
the RT-N12. It is, however, the same as the Linksys E3000v1.
Signed-off-by: Tim Thorpe <timfthorpe@gmail.com>
The memcpy of the init data relies on chip->registers to be initialized,
which only happens later in the code. Move this initialization further
down to make it work.
This was breaking PCIe/USB on some MikroTik RouterBoard devices.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The MAC addresses were not being set for LAN and WAN. This will now use the
same MAC mechanism as the rest of the target.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
TP-Link TL-WR840N v5 is simple N300 router with 5-port FE switch and
non-detachable antennas, based on MediaTek MT7628NN (aka MT7628N) WiSoC.
Specification:
- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 1x LED (GPIO-controlled), 1x button
* LED in TL-WR840N v5 is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Orange LED is registered so you can later use it for your own purposes.
Flash instruction:
Unlike TL-WR840N v4 flashing through WEB UI works in v5.
1. Download lede-ramips-mt76x8-tl-wr840n-v5-squashfs-sysupgrade.bin image.
2. Go to 192.168.0.1
3. Flash the sysupgrade image through Firmware upgrade section of WEB UI.
4. Wait until green LED stops flashing and use the router.
Notes:
TFTP recovery is broken since TP-Link reused bootloader code for v4 and
that does not take into account only 4 MB of flash and bricks the device.
So do not use TFTP Recovery or you will have to rewrite SPI flash.
They fixed it in later GPL code,but it is unknown which version of
bootloader you have.
After manually compiling and flashing bootloader from GPL sources TFTP
recovery works properly.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The splitter ignored the rootfs offset from the header, probably
because until c1e6e61 it was invalid.
This patch fixes the splitter to use the now correct header data.
Regarding target/linux/ar71xx/files/drivers/mtd/tplinkpart.c,
this particular splitter "falls back" to the correct rootfs offset
reading and as such it doesn't need to be updated, although it will
report a kernel partition length that can be larger than the actual
length as it assumes that partition fills the entire segment up to
the rootfs partition.
Tested-by: Mathias Kresin <dev@kresin.me>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Tested-by: Henryk Heisig <hyniu@o2.pl>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
- H3 @ 1.3 GHz
- 1GiB DDR3
- 10/100Mbps Ethernet
- Realtek RTL8189ETV wifi
- 4 USB 2.0
Difference to the "Orange Pi Plus" is the lack of Gbit ethernet
and lack of onboard flash.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Current jumbo frame support code allocates rxbuffers of the maximum size
supported by the hardware (~14KB). This happens at the device open time
even if the configured MTU is lower (e.g. if it configured to standard
1500 bytes). Such behavior effectivly prevents interface start on boards
with a low ammount of RAM (e.g. WRT300N v2), since the kernel simly can
not allocates of ~0.8MB (14KB x 64).
So remove jumbo frame support for now.
Reported-by: Nerijus Baliunas <nerijus@users.sourceforge.net>
Tested-by: Nerijus Baliunas <nerijus@users.sourceforge.net>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
The patch, which adds multiphy support, adds new path for non-standard
PHYs (e.g. MV88E6060 switch IC) to avoid using kernel phy framework. All
work well except the link status traking (Duplex and Speed), which is
reseted as soon as PHY connection procedure is done. This leads to lost
of the link status of non-standard PHY, which is configured exactly in
the ixp4xx_phy_connect() function.
Move the generic reset of a link state to the ixp4xx_phy_connect()
function to the code path, which is intended for handling of a normal
PHY.
Reported-by: Nerijus Baliunas <nerijus@users.sourceforge.net>
Tested-by: Nerijus Baliunas <nerijus@users.sourceforge.net>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
The MarsBoard was a short-lived credit-card sized, extendable board with an Allwinner A10 SoC.
http://linux-sunxi.org/MarsBoard_A10
Signed-off-by: Kayo Phoenix <kayo@illumium.org>
[Forward-ported to new target layout:]
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
On NOR based Mikrotik devices, 4K sectors significantly slow down
firmware flashing and jffs2 usage. On NAND based devices they may be
necessary to run rbcfg (the boot loader config is often on SPI NOR).
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Some targets need 4K sectors for small flash chips (e.g. some
routerboards, where the entire chip is just one "erase block"), whereas
on other devices 4K sectors lead to horrible flash erase/write
performance.
Set the default limit in the generic kernel configuration to 4 MiB to
ensure that all new platforms don't use 4K sectors for bigger flash
chips. On all existing targets use 16 MiB for now to avoid regressions.
They will be changed individually in follow-up commits.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This changes the cmdline from:
Kernel command line: root=/dev/mmcblk0p5 rootfstype=squashfs,ext4 rootwait noinitrd
Bootloader command line (ignored): board=NBG6817 root=/dev/mmcblk0p5 rootwait zld_ver=2.04 console=ttyHSL1,115200n8 mtdparts=m25p80:0xC0000(SBL)ro,0x40000(TZ)ro,0x40000(RPM)ro,0x80000(u-boot)ro,0x10000(env)ro,0x10000(ART)ro,0x10000(dualflag),0x210000(reserved)
to
Kernel command line: rootfstype=squashfs,ext4 rootwait noinitrd root=/dev/mmcblk0p5
Bootloader command line (ignored): board=NBG6817 root=/dev/mmcblk0p5 rootwait zld_ver=2.04 console=ttyHSL1,115200n8 mtdparts=m25p80:0xC0000(SBL)ro,0x40000(TZ)ro,0x40000(RPM)ro,0x80000(u-boot)ro,0x10000(env)ro,0x10000(ART)ro,0x10000(dualflag),0x210000(reserved)
As a consequence booting from the alternative dual-boot partition set
(root=/dev/mmcblk0p8) becomes possible.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
AP-DK01.1-C1 is QCA dev board with:
- ipq4018 quad core ARM @716.8MHz, 2x2 dual (11n+11ac) radio
- 256MB RAM
- 32MB SPI flash
- QCA8075 multiport ethernet phy (WAN port, 4x LAN ports)
First installation via u-boot:
sf probe
sf erase 0x180000 0x1a00000
tftpboot 0x84000000 lede-ipq806x-AP-DK01.1-C1-squashfs-sysupgrade.bin
sf write 0x84000000 0x180000 $filesize
Further upgrades via sysupgrade.
Changes:
- add partitions
- set memory size to 256MB
- add reserved memory mapping
- add correct compatible string
- add image generation
- extract pre-cal data from ART partition
Compile and run tested.
Wirespeed NAT can be achieved with spreading rx interrupts over different
cores. Wifi speed is ~550Mbps @5GHz in open air.
Note:
AP-DK01.1-C1 is fully compatible with AP-DK01.2-C1, which has
ipq4028 instead of ipq4018 on board.
Changes since v2:
- based on dts(i) rework/cleanup submitted:
http://lists.infradead.org/pipermail/lede-dev/2017-October/009596.html
- precise reserved memory mapping
- more precise description
- compatible string
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Supported frequencies of all ipq40xx chips are 48, 200, 500 and 716.8 MHz.
Previous 666MHz setting was most likely related to instability of early
chips/boards made before mass production.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
This fixes the LED configuration for the D-Link DIR-869 A1. In order to
support the device I probed around using an initramfs image for the
UniFi AC. Pulling GPIO 15 to low enabled the LEDs while high disabled them.
GPIO 16 set to low meant that the color was white while pulling it to high
made the color change to orange. The past code was written based upon these
findings.
However, running a flashed image I now discovered that GPIO 15 controls the
orange LEDs while GPIO 16 controls the white ones and that both are active
when low. This means that the GPIOs were inverted and one active_low was set
wrong which this patch fixes.
Behavior of the LED front after this patch is applied:
cat /sys/devices/platform/leds-gpio/leds/d-link:white:status/brightness
0 -> white LEDs are OFF
255 -> white LEDs are ON
cat /sys/devices/platform/leds-gpio/leds/d-link🍊status/brightness
0 -> orange LEDs are OFF
255 -> orange LEDs are ON
If the brightness of both is set to 255 the LED front will be white.
If the brightness of both is set to 0 the LED front will be off.
Signed-off-by: Florian Beier <beier.florian@gmail.com>
The GPIOs are used for defined LEDs and therefore are ignored/unset in
the ath9k driver since 192f0a3db8. The wireless led led trigger is
added in userspace since e20965811d, which makes the
ap9x_pci_setup_wmac_led_pin() superfluous.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The platform data was missing the num_registers element which is now
mandatory in linux 4.9
Without this patch, the gpio probing would fail with:
gpio gpiochip1: (74x164): tried to insert a GPIO chip with zero lines
Fixes: #1106
Tested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
The ZyXEL NBG6817 calculates all MAC addresses based on the ethaddr
value stored in the U-Boot environment (0:APPSBLENV). No MAC addresses
are stored in the ART partition and the generated MAC addresses for the
wlan interfaces alternate randomly between 12:34:56:78:90:12 and
00:03:7f:12:34:56.
interface new/ OEM MAC old MAC
wlan-2.4g (phy1): ethaddr undefined
wlan-5g (phy0): ethaddr + 1 undefined
lan : ethaddr + 2 ethaddr
wan : ethaddr + 3 ethaddr + 1
This patch defines stable MAC addresses for the wlan interfaces for
the first time instead of generating them at random. The previously
defined values for lan/ wan are changed to follow the settings of the
OEM firmware.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
The ZyXEL NBG6817 uses an eMMC flash for the rootfs, which is split
into the readonly squashfs and ext4 for the overlay. This adds the
required package to the device packages to allow mounting the overlay
by default.
/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,nosuid,nodev,noexec,noatime)
sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime)
/dev/loop0 on /overlay type ext4 (rw,noatime,data=ordered)
overlayfs:/overlay on / type overlay (rw,noatime,lowerdir=/,upperdir=/overlay/upper,workdir=/overlay/work)
tmpfs on /dev type tmpfs (rw,nosuid,relatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,mode=600,ptmxmode=000)
debugfs on /sys/kernel/debug type debugfs (rw,noatime)
mountd(pid1040) on /tmp/run/blockd type autofs (rw,relatime,fd=7,pgrp=1,timeout=30,minproto=5,maxproto=5,indirect)
Before this commit, the ext4 based overlayfs could not be mounted,
which left only the tmpfs based/ volatile emergency overlay in place.
Fixes: https://forum.lede-project.org/t/zyxel-nbg6817-flashing-from-oem/768
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
On some devices the flash chip needs to be in 3-byte addressing mode during
reboot, otherwise the boot loader will fail to start.
This mode however does not allow regular reads/writes onto the upper 16M
half. W25Q256 has separate read commands for reading from >16M, however
it does not have any separate write commands.
This patch changes the code to leave the chip in 3-byte mode most of the
time and only switch during erase/write cycles that go to >16M
addresses.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Serial output was broken since 3.16 for shared uarts between
kernel and login. Fix this by adding a fix sent upstream.
While at it, drop a useless patch that adds duplicate code.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The NXP LSDK kernel backported changes for interface ndo_get_stats64
functions from mainline, this causes a compile error with
backports/mac80211, which expects the original 4.9 defintion.
As reversing the ndo_get_stats64 change signifcantly reduces the size of
patch 601, the patches that were aggregated into it have been
disaggregated.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
These conflict with the kmod packages (such as nf-netlink)
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[Add same changes for arm8_32b subtarget and refresh config]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Mark target arc770 as source-only as it has package compile issues
(e.g. iproute2) due to the usage of uClibc.
As a prerequisite to be included in future releases the arc770 target
needs to switch either to glibc or musl.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Remove the ephy-pins from the ethernet device tree node. The ephy-pins
are useed to controll the ePHY LEDs and this board doesn't have these.
Instead one of the ePHY pins is used in GPIO mode to control the WAN
LED.
Use the switch LED trigger to control the WAN LED. Move the power LED
handling to diag.sh to show the boot status via this LED.
Add the missing kernel packages for USB and microSD card reader to the
default package selection.
Fix the maximum image size value. The board has a 32MByte flash chip.
Fixes: FS#1055
Signed-off-by: Edmunt Pienkowsky <roed@onet.eu>
[make the commit message more verbose, remove GPIO pinmux for pins not
used as GPIOs]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Without this, posix_[fm]advise does not work. This causes issues with
btrfs-progs, which uses fadvise to drop caches.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This commit fix 5GHz wireless interface used in Archer C58/C59/C60v1
and set correctly MAC address on this interface.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
IMG_PREFIX can be modified in ImageBuilder by passing EXTRA_IMAGE_NAME
on command line, but Image/Prepare is not run in ImageBuilder. This
causes missing files when IMG_PREFIX is used for target file names in
Image/Prepare, then as source file names in Image/BuildKernel or
Image/Build.
Fix this by using a fixed output file name in Image/Prepare, and copy to
the expected file name in Image/BuildKernel instead, which is run by
ImageBuilder.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Remove reference to pinmux group "wdt rst" on EW1200, ZBT-WG2626 and
ZBT-WG3526 devices. "wdt rst" is a pinmux function and not a pinmux
group.
Fixes the following error message during boot:
rt2880-pinmux pinctrl: invalid group "wdt rst" for function "gpio"
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Zyxel NBG6817 features a WiFi button, which becomes functional by setting
correct GPIO. It is a switch-type button, so it emits KEY_RFKILL on each ON
and OFF state. This is achieved by setting input-type to EV_SW.
Signed-off-by: Tolga Cakir <tolga@cevel.net>
Add the respective colour to the LED's names for the GL-AR150 to be conform
to the kernel. Also add netdev triggers for the LAN and WAN LED.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Append and enforce image metadata. Remove the device specific image
checks, they are replaced by image metadata.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the values populated by the generic board detect function. The
first compatible from the device tree source file will be the board
name in userspace. The model property from the device tree source file
will be the model name.
Change the board name where used in the userspace and drop the target
specific board detect, to use the generic one.
Signed-off-by: Mathias Kresin <dev@kresin.me>
initramfs is not the proper name for this, as it stores a boot ramdisk
and not a filesystem. Update the name to reflect it's usage correctly.
If CMDLINE_OVERRIDE is enabled, the chosen bootargs aren't used at all.
Drop them from the device tree source file to not cause confusion.
Remove the noinitrd bootarg. Due to the empty ramdisk this parameter
isn't required any longer:
[ 0.000000] Initrd not found or empty - disabling initrd
Use the LEDE mtd-mac-address* device tree properties to set the interfaces
MAC-Addresses.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Move the kernel config changes added with the HiveAP 330 to the
subtarget the board belongs to instead of changing the target kernel
config.
While at it, move the TL_WDR4900_V1 config symbol to the containing
subtarget and disable boards we don't support.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The following moves the mpc85xx target (generic & P1020) to the new
build code style.
Compile & Flash tested on an Aerohive HiveAP-330.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
That device does not have a USB port. It as the same board as the
WT3020-8M, but without soldered USB port port. Also the case lacks the
opening for the port.
Reported-by: Alberto Bursi <alberto.bursi@outlook.it>
Signed-off-by: Mathias Kresin <dev@kresin.me>
the nexx wt3020-8M has a usb 2.0 port,
add usb 2.0 support packages to its default package list.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
This change makes it possible to configure the wan/dsl ppp interface
settings independantly from the used TC-Layer (ATM/PTM).
By using dsl0 as interface name as for the xrx200 we can get rid of a
few conditionals which were introduced because of the different default
TC-Layer in xway and xrx200.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Set a default Annex matching the the annex of the selected adsl
firmware.
Set Annex B for xrx200 board which are known to have an ADSL hybrid for
Annex B.
Signed-off-by: Mathias Kresin <dev@kresin.me>
With removing the boards from the the default case to fix the xDSL WAN
MAC-Address, the setting for the default LAN interface wasn't added.
Fixes: 92a12c434c ("lantiq: fix avm fritz box mac addresses")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Patch 610-netfilter_match_bypass_default_check added an extra flag IPT_F_NO_DEF_MATCH
which is copied to user space in function copy_entries_to_user. The 32bit compat
layer function was missing the same logic to copy the flag IPT_F_NO_DEF_MATCH to
user space for a 64bit kernel and 32 bit user space.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Thierry Dutre <thierry.dutre@dtsystems.be>
Patch 610-netfilter_match_bypass_default_check added an extra flag IPT_F_NO_DEF_MATCH
which is copied to user space in function copy_entries_to_user. The 32bit compat
layer function was missing the same logic to copy the flag IPT_F_NO_DEF_MATCH to
user space for a 64bit kernel and 32 bit user space.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Thierry Dutre <thierry.dutre@dtsystems.be>
Patch 610-netfilter_match_bypass_default_check added an extra flag IPT_F_NO_DEF_MATCH
which is copied to user space in function copy_entries_to_user. The 32bit compat
layer function was missing the same logic to copy the flag IPT_F_NO_DEF_MATCH to
user space for a 64bit kernel and 32 bit user space.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Thierry Dutre <thierry.dutre@dtsystems.be>
On RB91x (and possibly others), there is a small SPI flash to store boot
loader and configuration. It needs 4K sectors to be able to write the
configuration using rbcfg
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In 4.9, gpio count is rounded up to 32 due to the use of bgpio in the
ath79 gpio controller driver.
Fix base values in mach files to account for that
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Change the Makefile to use LTO for better code optimisations. Gains are
very low, only 270 bytes saved, but it's only Makefile changes.
Signed-off-by: Julien Dusser <julien.dusser@free.fr>
Some bootloaders set a cache cohenrency to a very slow mode. Use code from
Linux kernel to set it to "Cacheable, noncoherent, write-back, write
allocate".
Perfomance impact is significant on TP-Link EAP245 board, kernel
decompression time fall from 33 seconds to less than 1.
Signed-off-by: Julien Dusser <julien.dusser@free.fr>
The Raspberry Pi bootloader reads configuration values from config.txt
in the boot partition. This file allows to specify the amount of memory
to assign to the GPU, the license keys for hardware MPEG-2 and VC-1
decoding, Device Tree parameters and overlays, and lots of other things.
Since sysupgrade only restores the configuration after booting the newly
flashed image, these values will not be active, even if sysupgrade would
save /boot/config.txt. To solve this, add the file to the files to be
backed up, and restore it in platform_copy_config, before reboot.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This affects the following boards:
* dr344
* archer-c58-v1
* archer-c60-v1
* tl-wr902ac-v1
* tl-wr942n-v1
* ubnt-uap-pro
* ubnt-unifi-outdoor-plus
The build fails for any of these boards because the resulting kernel
image will not fit into the kernel partition.
When CONFIG_KERNEL_KALLSYMS is not set it could be that the kernel will
fit onto the board again, this is the case for release images.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Kernel 4.9 support was added about 2 weeks ago and we haven't seen any
major regression so far. This patch was not ported to kernel 4.9, this
needs some additional work:
821-serial-core-add-support-for-boot-console-with-arbitr.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When the kmod-at91-adc package is activated for the at91 target the new
option CONFIG_AT91_SAMA5D2_ADC is selectable and not handled. Add this
option to the kernel 4.9 configuration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
TP-Link Archer C7 v4 is a dual-band AC1750 router, based on Qualcomm/Atheros
QCA9561+QCA9888.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Flash instruction:
1. Upload lede-ar71xx-generic-archer-c7-v4-squashfs-factory.bin via Web interface
Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c7-v4-squashfs-factory.bin
and rename it to ArcherC7v4_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Flash instruction under U-Boot, using UART:
1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f040000 +$filesize
3. cp.b $fileaddr 0x9f040000 $filesize
4. reset
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Specifications:
- SoC: Qualcomm QCA9558 (720 MHz)
- RAM: 256MB
- Storage: 1MB NOR, 128 MB NAND flash
- Ethernet: 1x1000M
Installation:
1. Connect to serial console on the board
2. Boot initramfs image over u-boot
3. Copy image to the device and run sysupgrade
Installation without serial console is not supported at this time
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Kernel 4.9 is now working on the brcm47xx boards, we just recently fixed
the problem that some boards did not boot at all, by changing the memory
regions used to relocate the kernel to in the loader.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When porting the kernel patches from 4.4 to 4.9, they were missing a
small chunk that ensures that ftrace sections are kept in the vmlinux
image, even when linked with --gc-sections
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The ARV752DPW22 has the same generic mac address in the EEPROM as it
was already noticed for other lantiq boards using a ralink wireless.
Use the base mac address from the boardconfig partition as it is done
by the stock firmware.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This adds support for kernel 4.9 and replaces the kernel 4.4 support.
These are lynxis test results:
panda-board a3 - works, but no network, but master/4.4 doesn't have network either.
panda-board-a4 - u-boot SPL refuse to boot.
beaglebone-black - works
beagle-board - usb attached network doesn't come up and I doesn't have a serial around.
beagle-board-xm - ToDo: image code is missing.
Kernel 4.4 does not look better, so we merge this anyway.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Alexander Couzens <lynxis@fe80.eu>
This reverts commit 13e5e47369.
This commit causes a severe regression in LAN->WAN routing performance
for several devices. This appears to be caused by the extra requirement
to validate the SKB checksum early in the rx path, which the ethernet
hardware does not do
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The build system took the DTB_SIZE definition from Default and not from
production-dtb under some conditions. Move the size definitions to
Default now as it is only used in production-dtb anyway.
Thanks Mathias Kresin for helping me with this.
Fixes: c2f052acae ("at91: convert boards to generic build target")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These options where deactivated in the malta kernel, take the default
options form the generic kernel configuration now to better match the
other targets.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This change makes it possible to configure the wan/dsl ppp interface
settings independantly from the used TC-Layer (ATM/PTM).
Now you can move a device from an ADSL/ATM port to an VDSL/PTM port
without any configuration changes for example.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[use the dsl0 interface name for the default netdev trigger in 01_led,
add ip dependency]
Signed-off-by: Mathias Kresin <dev@kresin.me>
It is unclear why so many packages are selected for ClearFog Base compared
to its big brother, and there is no reason to not append metadata for Base.
Tidy this up as the only hardware difference between Base/Pro is the
presence of a switch and a different board name / device tree.
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
Remove redundancy for platform_do_upgrade_clearfog
Fix platform_copy_config_clearfog to reflect -base/-pro split
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
This module from Laird includes the following:
- CPU Atmel SoC SAMA5D31
- Wifi QCA6004
- Bluetooth CSR8811
- RAM 64MB LPDDR
- FLASH 128MB
The flash is a dual image layout, kernel a/b, rootfs a/b, and a user
partition.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
This module from Laird includes the following:
- CPU Atmel SoC ARM926EJS
- Wifi AR6003
- Bluetooth CSR8510
- RAM 64MB LPDDR
- FLASH 128MB
The flash is a dual image layout, kernel a/b, rootfs a/b, and a user
partition.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Instead of applying global defaults based on selected board, transition
to using a per board setting for UBIFS and UBINIZE.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
The platform generates squashfs images in a UBI block but misses the
kernel module to be able to mount the block.
DMA is also enabled to allow systems which include them in the DTS to
use it.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Specifications:
- SoC: Qualcomm QCA9531 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Ethernet: 5x100M (1 PoE in, 4 PoE out)
- Outdoor use ready
This ethernet router is based on the same platform as the hEX PoE lite.
Installation
1. login to the Mikrotik WebUI to backup your licence keys
2. setup a DHCP/BOOTP Server with:
* DHCP-Option 66 (TFTP server name) pointing to a local TFTP
Server within the same subnet of the DHCP range
* DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
of the to be booted image
3. connect the port labled internet to your local network
4. keep the reset button pushed down and power on the board
The board should load and start the initramfs image from the TFTP
Server. Login as root/without password to the started LEDE via ssh
listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE.
Revert to RouterOS
Use the "rbcfg" package on in LEDE:
* rbcfg set boot_protocol bootp
* rbcfg set boot_device ethnand
* rbcfg apply
Open Netinstall and reboot routerboard. Now netinstall sees routerboard
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.
Click on install again.
In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall
Signed-off-by: Robert Marko <robimarko@gmail.com>
Kimax U-25AWF-H1 is is a 2,5" HDD Enclosure with Wi-Fi/Eth conection
and battery, based on MediaTek MT7620A.
Patch rewritten from: https://forum.openwrt.org/viewtopic.php?pid=305643
Specification:
- MT7620A CPU
- 64 MB of RAM
- 16 MB of FLASH
- 802.11bgn WiFi
- 1x 10/100 Mbps Ethernet
- USB 2.0 Host
- UART for serial console
Flash instruction:
1. Download lede-ramips-mt7620-u25awf-h1-squashfs-sysupgrade.bin
2. Open webinterface a upgrade
3. After boot connect via ethernet to ip 192.168.1.1
Signed-off-by: Daniel Kucera <daniel.kucera@gmail.com>
[fix reset button gpio, don't add a lan/wan vlan config for single
port board, add -H1 suffix do make sure that this revision of the
board is supported/tested]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The following adds the Aerohive HiveAP-330 Access Point to LEDE under
the mpc85xx/p1020 subtarget.
Hardware:
- SoC: Freescale P1020NSE2DFB
- NAND: Intel JS28F512M29EWH 64MB
- Memory: 2x ProMOS V59C1G01168QBJ3 128MB (Total of 256MB)
- 2.4GHz WiFi: Atheros AR9390-AL1A
- 5.0GHz WiFi: Atheros AR9390-AL1A
- Eth1: Atheros AR8035-A PoE
- Eth2: Atheros AR8035-A
- TPM: Atmel AT97SC3204
- LED Driver: TI LP5521
Flashing:
1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter a
password of administrator or AhNf?d@ta06 if prompted.
2. Once in U-Boot, tftp boot the initramfs image:
dhcp;
tftpboot 0x1000000 192.168.1.101:lede-
mpc85xx-p1020-hiveap-330-initramfs.zImage;
tftpboot 0x6000000 192.168.1.101:lede-mpc85xx-p1020-hiveap-330.fdt;
bootm 0x1000000 - 0x6000000;
3. Once booted, scp over the sysupgrade file and sysupgrade the device
to flash LEDE to the NAND.
sysupgrade /tmp/lede-mpc85xx-p1020-hiveap-330-sysupgrade.img
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
This patch adds a new kernel option called CONFIG_CMDLINE_OVERRIDE. This
setting is for devices with locked down u-boot environments, where users
are unable to change the default bootargs. When set, the fdt driver will
propagate the cmdline for the kernel from chosen/bootargs-override
instead of chosen/bootargs as long as it exists within the DTB.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
The following patch enables building of initramfs images by default for
the P1020 subtarget in mpc85xx.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Add ext4 filesystem for creating sdcard image with ext4 rootfs and
removing ext2 as it superset of ext4.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Enabled SDHCI for sama5 in kernel default config and this is needed
to mount sdcard rootfs partition during boot.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
This PHY requires some extra programming to work reliably with all
devices. Backport upstream fix for it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This is no requirement and plan to support 32-bit for ls1088ardb
and ls2088ardb. Current 32-bit firmware for them couldn't work,
so only keep 64-bit support for these two boards in menuconfig.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
When build firmware for layerscape target with CONFIG_ALL_NONSHARED=y,
there would be a compile issue of usb ehci-fsl driver. Actually this
driver was for PPC platforms initially and was not ready for non-PPC
now, but a kernel kconfig patch removed PPC dependency for it. So that
kernel patch should be reverted.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This add support for kernel 4.9 to the ar71xx target.
It was compile tested with the generic, NAND and mikrotik subtarget.
Multiple members of the community tested it on their boards and did not
report any major problem so far.
Especially the NAND part received some changes to adapt to the new
kernel APIs. The serial driver hack used for the Arduino Yun was not
ported because the kernel changed there a lot.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
By default we are reusing the stack provided by CFE, like it is intended
by CFE. On my WRT54GS it is located at 0x8043BF30, so a big kernel image
could overwrite it. Relocate it to a different memory region which is
still under the 8MB RAM, but in the higher area. We only need this
memory region for the stack of the loader, Linux will set up this
for its own.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The boot process on a WRT54GL works the following way:
1. CFE gets loaded by the boot rom from flash
2. CFE loads the loader from the flash and gzip uncompresses it
3. CFE starts the loader
4. The loader stores the FW arguments and relocates itself to
BZ_TEXT_START (now 0x80600000)
5. The loader reads the Linux image from flash
6. The loader lzma decompresses the Linux image to LOADADDR (0x80001000)
7. The loader executes the uncompress Linux image at LOADADDR
The BZ_TEXT_START was set to 0x80400000 before. When the kernel gets
uncompressed and is bigger than BZ_TEXT_START - LOADADDR it overwrote
the loader which was currently uncompressing it and made the board
crash. Increase the BZ_TEXT_START my 2 MB to have more space for the
kernel. Even on 16MB RAM devices the memory goes till 0x80FFFFFF so this
should not be a problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>