This just copies the patches, configuration and dts files into the
directories hich are used for kernel 4.14.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Move the devicetree source files to a kernel specific directory in
preparation of adding kernel 4.14 support.
Rename the subtarget kernel config files to match a specific kernel
version.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Users are confused which image type they should use and there are more
drawbacks than adavantages in using a r/w ubifs rootfs in constrast to
a read-only squashfs rootfs like:
- less available free flash space due to better compression of squashfs
images
- no support for factory reset due to r/w filesystem
- possibility to break failsafe due to r/w filesystem
Therefore, drop support for r/w ubifs rootfs images.
Signed-off-by: Mathias Kresin <dev@kresin.me>
AmazonSE and Falcon do not have support for PCI and it can't be
unselected in the subtarget kernel config. This way the enabled PCI
support is inherit from the higher level config to the subtarget.
If CONFIG_PCI is selected, PCI_SUPPORT will be autoselected as well and
all packages depending on this config symbol will be build and at least
some of them fail due to missing pci functions.
The issue can be observed if all kmods and all non-shared packages are
build. Fix the issue by enabling PCI support only in subtargets with
PCI support.
Signed-off-by: Mathias Kresin <dev@kresin.me>
CONFIG_MTSCHED & CONFIG_PERFCTRS were never defined in the kernel.
CONFIG_LANTIQ_PHY was replaced by CONFIG_INTEL_XWAY_PHY with the switch
to the upstreamed driver.
Add autoselected dependecies to the kernel config.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The following patches were dropped because they are already applied
upstream:
0012-pinctrl-lantiq-fix-up-pinmux.patch
0013-MTD-lantiq-xway-fix-invalid-operator.patch
0014-MTD-lantiq-xway-the-latched-command-should-be-persis.patch
0015-MTD-lantiq-xway-remove-endless-loop.patch
0016-MTD-lantiq-xway-add-missing-write_buf-and-read_buf-t.patch
0017-MTD-xway-fix-nand-locking.patch
0044-pinctrl-lantiq-introduce-new-dedicated-devicetree-bi.patch
0045-pinctrl-lantiq-Fix-GPIO-Setup-of-GPIO-Port3.patch
0046-pinctrl-lantiq-2-pins-have-the-wrong-mux-list.patch
0047-irq-fixes.patch
0047-mtd-plat-nand-pass-of-node.patch
0060-usb-dwc2-Add-support-for-Lantiq-ARX-and-XRX-SoCs.patch
0120-MIPS-lantiq-add-support-for-device-tree-file-from-bo.patch
0121-MIPS-lantiq-make-it-possible-to-build-in-no-device-t.patch
122-MIPS-store-the-appended-dtb-address-in-a-variable.patch
The PHY driver was reduced to the code adding the LED configuration,
the rest is already upstream:
0023-NET-PHY-adds-driver-for-lantiq-PHY11G.patch
The SPI driver was replaced with the version pending for upstream
inclusion:
New driver:
0090-spi-add-transfer_status-callback.patch
0091-spi-lantiq-ssc-add-support-for-Lantiq-SSC-SPI-controller.patch
Old driver:
0100-spi-add-support-for-Lantiq-SPI-controller.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
(cherry picked from commit 064f467264c5c9b6eca0bb96b587f9412b770cc5)
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
GCC treats 24kc and 34kc exactly the same and will generate identical
code, so there is no need to tune to 34kc instead of 24kc.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
There does not seem to be any meaningful difference in generated code.
This will save some time and space on snapshot builds
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The RJ45 WAN port is used for xDSL as well as the IP101A.
The pins 1,2,3,6 of the RJ45 are connected to the IP101A and the
pins 4,5 are connected to the xdsl chip.
Drop the ip101a-rst node. It can't be controlled and is not required
at all.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The only difference between the VG3503J profiles is the version of the
gphy firmware that gets loaded. This can be handled perfect fine in one
device tree source file.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This adds basic support for TP-Link VR200v.
Currently the following parts are not working: FXO, Voice, DECT, WIFI (both)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48328
Compared to the "old" driver:
- Each device must assign a pinctrl setting to the SPI node to allow the
new SPI driver to configure the SPI pins.
While here we are also using separate input and output settings so we
are independent of whether the bootloader configures the pins correctly.
- We use the new "compatible" strings to make the driver choose the
correct number of chip-selects for each SoC.
- The new driver starts counting the chip-selects at 1 (instead of 0, like
the old one did). Thus we have to adjust the devices accordingly.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48293
All devices are now using the HW SPI driver, so this is not necessary
anymore.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48291
Because of dsl-vrx200-firmware-xdsl-* there's no need anymore to
download a dsl firmware at runtime.
Signed-off-by: Andre Heider <a.heider@gmail.com>
SVN-Revision: 47851
The device is similar to the TD-W8970, beside a different Atheros 2.4 GHz
wireless chip and the additional, PCI connected, WAVE300 5 GHz wireless.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47130
Disable ARCH_NEEDS_CPU_IDLE_COUPLED by-default in generic config, since
only one platfrom (omap) needs them.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44614
CONFIG_MTD_SPLIT_SUPPORT symbol default value is 'y' and many platform
specific configs explicitly enables it, while no one platform disables
this symbol. So place it in generic config and remove from platform
specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44612
CONFIG_GENERIC_NET_UTILS is selected by CONFIG_NET and already enabled
in generic config, so we don't need this symbol in platform specific
configurations.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44611
Most MIPS targets have it disabled, so move the symbol to the generic
configs to keep target configs small.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44583
