Add RXIQ calibration found in mtk driver. With old openwrt builds this gets us ~8Mbps more of RX bandwidth (test with iPA/eLNA layout).
Please try if this makes any difference among various board/RF layouts.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Add RXDCOC calibration code from mtk driver. Please try if this makes any difference among various board/RF layouts.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Write registers required for reducing power consumption like the vendor
driver does when ADJUST_POWER_CONSUMPTION_SUPPORT is set.
This helps devices to sync at better TX/RX rates and improves overall
performance.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: edited commit message]
Registering a GPIO chip with the ath9k device as parent prevents unload,
because the gpiochip core increases the module use count.
Unfortunately, the only way to avoid this at the moment seems to be to
register the GPIO chip without a parent device
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Tri-band devices (1x 2.4GHz + 2x 5GHz) often incorporate special filters in
the RX and TX path. These filtered channel can in theory still be used by
the hardware but the signal strength is reduced so much that it makes no
sense.
There is already a DT property to limit the available channels but ath10k
has to manually call this functionality to limit the currrently set wiphy
channels further.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Monitor mode isn't supported yet with brcmfmac, it's just an early work.
This also prepares brcmfmac to work stable with new firmwares which use
updated struct for passing STA info.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The most important is probably regression fix in handling platform
NVRAM. That bug stopped hardware from being properly calibrated breaking
e.g. 5 GHz for Netgear R8000.
Other than that it triggers memory dumps when experiencing firmware
problems which is important for debugging purposes.
Fixes: 7e8eb7f309 ("mac80211: backport brcmfmac firmware & clm_blob loading rework")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This commit refreshes and updates the VHT160 ath10k support fix patches
and adds a number of backports from ath-next:
* 8ed05ed06fca ath10k: handle tdls peer events
* 229329ff345f ath10k: wmi: modify svc bitmap parsing for wcn3990
* 14d65775687c ath10k: advertise TDLS wider bandwidth support for 5GHz
* bc64d05220f3 ath10k: debugfs support to get final TPC stats for 10.4 variants
* 8b2d93dd2261 ath10k: Fix kernel panic while using worker (ath10k_sta_rc_update_wk)
* 4b190675ad06 ath10k: fix kernel panic while reading tpc_stats
* be8cce96f14d ath10k: add support to configure channel dwell time
* f40105e67478 ath: add support to get the detected radar specifications
* 6f6eb1bcbeff ath10k: DFS Host Confirmation
* 260e629bbf44 ath10k: fix memory leak of tpc_stats
* 38441fb6fcbb ath10k: support use of channel 173
* 2e9bcd0d7324 ath10k: fix spectral scan for QCA9984 and QCA9888 chipsets
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[move backported patches in the 3xx number space, bring in upstream order,
replace incomplete patch files with git format-patch ones, rewrite commit
message, fix subject]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Most of the implementations behind cfg80211_get_station will not initialize
sinfo to zero before manipulating it. For example, the member "filled",
which indicates the filled in parts of this struct, is often only modified
by enabling certain bits in the bitfield while keeping the remaining bits
in their original state. A caller without a preinitialized sinfo.filled can
then no longer decide which parts of sinfo were filled in by
cfg80211_get_station (or actually the underlying implementations).
cfg80211_get_station must therefore take care that sinfo is initialized to
zero. Otherwise, the caller may tries to read information which was not
filled in and which must therefore also be considered uninitialized. In
batadv_v_elp_get_throughput's case, an invalid "random" expected throughput
may be stored for this neighbor and thus the B.A.T.M.A.N V algorithm may
switch to non-optimal neighbors for certain destinations.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
After a very enlightening but unfortunately far too short exchange with Jes
we mutually agreed to drop the patches. They are unfortunately not ready
yet.
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: John Crispin <john@phrozen.org>
Use the tpt LED trigger for each created phy led. Ths way LEDs attached
to the ath10k GPIO pins are indicating the phy status and blink on
traffic.
Signed-off-by: Mathias Kresin <dev@kresin.me>
It was described by Arend as:
> This series is intended for 4.17 and includes following:
>
> * rework bus layer attach code.
> * remove duplicate variable declaration.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Some ath10k firmware versions allow to access the chip internal a
temperature sensor and allow to reduce the amount of the time when the card
is allowed to send. The latter is required on devices which tend to
overheat.
An userspace service has to read
/sys/class/ieee80211/phy*/device/hwmon/hwmon*/temp1_input regularly and
then decide how much the device has to be throttled. This can be done by
writing to /sys/class/ieee80211/phy*/device/cooling_device/cur_state. By
default it is not throttled (0) but it can be throttled up to 100(%).
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Import a revert-commit from Stanislaw Gruszka which significantly
improves WiFi performance on rt2x00 based hardware.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch was revised upstream before being merged, and OpenWrt's copy
was never updated to reflect the revision.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
[refreshed patches]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Merge upstream patch from Sathishkumar Muruganandam
<murugana@codeaurora.org> for OpenWrt's backports package:
https://lkml.kernel.org/r/<1522049641-19521-1-git-send-email-murugana@codeaurora.org>
Commit-ID: 606204bb863fa3b0bb54929d79b4dc46338f9180
* FW has Smart Logging feature enabled by default for detecting failures
* and processing FATAL_CONDITION_EVENTID (36925 - 0x903D) back to host.
*
* Since ath10k doesn't implement the Smart Logging and FATAL CONDITION
* EVENT processing yet, suppressing the unknown event ID warning by moving
* this under ATH10K_DBG_WMI.
*
* Simulated the same issue by having associated STA powered off when
* ping flood was running from AP backbone. This triggerd STA KICKOUT
* in AP followed by FATAL CONDITION event 36925.
*
* Issue was reproduced and verified in below DUT
* ------------------------------------------------
* AP mode of OpenWRT QCA9984 running 6.0.8 with FW ver 10.4-3.5.3-00053
*
* Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
When CONFIG_PM was not set rsi_sdio_reinit_device() was not compiled
into the driver but referenced.
This is a backport form the mainline Linux kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
RedPine RS9113 wireless module requires rsi91x driver to be built
and linux-firmware/rsi/rs9113_wlan_qspi.rps to be installed.
Also we add patch for successful compilation of rsi91x driver.
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: John Crispin <john@phrozen.org>
This patch adds the patch that was posted to ath10k-devel ML:
<https://patchwork.kernel.org/patch/10233491/>
|From: Thomas Hebb <tommyhebb@gmail.com>
|Subject: [PATCH] ath10k: search all IEs for variant before falling back
|Date: Wed, 21 Feb 2018 11:43:39 -0500
|[...]
|This patch fixes the issue by first searching the entire file for the ID
|with variant, and searching for the fallback ID only if that search
|fails. It also includes some code cleanup in the area, as
|ath10k_core_fetch_board_data_api_n() no longer does its own string
|mangling to remove the variant from an ID, instead leaving that job to a
|new flag passed to ath10k_core_create_board_name().
|
|I've tested this patch on a QCA4019 and verified that the driver behaves
|correctly for 1) both fallback and variant BDFs present, 2) only fallback
|BDF present, and 3) no matching BDFs present.
|
|Fixes: 1657b8f84ed9 ("ath10k: search SMBIOS for OEM board file extension")
|Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Note: 937-ath10k-calibration-variant.patch has been reassigned a new 081
number, as it now ships with upstream.... But also because this patch
requires the change in ath10k_core_create_board_name().
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
