Use the 'swconfig_trig_set_brightness' function to set
the brightness value of the LED when the link goes down.
This ensures that the last brighness value is saved into
a local variable which is used to track the actual LED
status.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39402
This reverts r38197.
The automatically created firmware partition includes
the partition_table partition. Apart from the partition
table, this partition contains sensitive data on some
Compex devices which data can be destroyed when the
firmware partition gets modified. Revert the change to
prevent that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39382
This patch enables jumbo frames on AR8327 switch by default.
I have tested it on TP-Link TL-WDR3600.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 39076
This patch is needed to use the switch inside the Sitecom WLR-8100;
it was unusable and detected as Generic-Phy before.
since ar8337 is behaving like ar8327
generally do the same thing
see: https://forum.openwrt.org/viewtopic.php?pid=214218#p214218
forward-ported to trunk
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Patchwork: http://patchwork.openwrt.org/patch/4469/
[juhosg: merge chip_is_ar83[23]7 statements in ar8xxx_phy_config_init]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38952
The BCM5365 needs a shift of 7 bits and not 6 bits like the BCM5325 for
the untagged ports.
Thank you Russell for reporting this and testing the patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38793
This patch makes it possible to use adm6996.c on first generation
BCM47XX devices with ADM switches.
The GPIO bit banging protocol implementation was copied from the old
switch driver and adapted to this driver and changed to the mainline
kernel GPIO interface.
The ADM6996L is different from the ADM6996M which is supported, for
both specs are available in the Internet.
This was tested on a WRT54GS version 1.0, thank you Dirk Neukirchen for
the device.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38698
The revision is stored in a different register than it is in other
Broadcom switches.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37995
These switches are integrated in some recent BCM53XX and BCM47XX SoCs
like the BCM53572.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37994
The Linksys wrt310n v1 does not have a robo_reset config variable in
nvram, but GPIO Pin 8 is the pin needed for resetting the external
switch, Linksys hard coded it into their source code.
Thank you Devastator for testing.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37988
BCM5365 (and probably other older variants) use a different phy id, so
the phy driver never attached for them.
Fix this by adding the appropriate phy id to the fixup and the phy
driver.
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 37906
b53_no_ops has no elements and b53_port_ops has one element, this makes
the code access some random memory when trying to access the mib
counter functions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37895
The myloader partition parser code uses ifdef wrappers
to make the code usable on kernels below version 3.2.
All targets are using kernel 3.3 at least so the wraper
is not needed. Remove that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37880
This is needed for some switches used on bcm47xx SoCs like the one on the Asus RT-N66U.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37645
There is no platform using the gpio-pwm driver, yet these patches break the
generic PWM framework that is in upstream. So just remove them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
SVN-Revision: 37490
It hasn't been buildable for a long time, and there are no users of it
anymore left as all of them have been switched to the upstream accepted
version.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 37436
This makes it possible to use swconfig to controll the switch.
This was tested with devices using b43 and bgmac.
This was not tested on devices using tg3.
This does not support the adm switch used in some very old devices.
SVN-Revision: 37304
This patch adds swlib attributes to the RTL8366RB switch/PHY found in the
TL-WR1043ND router that allow to mirror ethernet packets to a monitor port.
Signed-off-by: Colin Leitner <colin.leitner@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36847
Tested on Buffalo WZR-600DHP with ar8316 switch. Commands used to mirror both
RX and TX traffic from LAN port 1 to LAN port 4:
$ swconfig dev switch0 set enable_mirror_rx 1
$ swconfig dev switch0 set enable_mirror_tx 1
$ swconfig dev switch0 set mirror_monitor_port 4
$ swconfig dev switch0 set mirror_source_port 1
Signed-off-by: Colin Leitner <colin.leitner@googlemail.com>
Tested-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 36713
drivers/net/phy/rtl8366_smi.c: In function 'rtl8366_sw_set_vlan_ports':
drivers/net/phy/rtl8366_smi.c:1125:6: warning: 'pvid' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36442
* disable external interface if its property is not present
* show an error message if the extif property is not valid
* use proper error values intead of -1
* fix memory leak
* wrap long lines
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36229
The AR8327 switch gets its configuration from platform
data or from the device-tree. This allows to start it
from the probe routine. Doing so makes it usable with
ethernet drivers which only connects to the PHY device
when the ethernet interface is opened.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36050
Move switch starting code into a separate function.
This makes it usable from other places.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36049
Move platform_data specific configuration code
into a separate routine. Do it in preparation
for the upcoming OF support.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36046
Fetch the PORT_STATUS values in ar8327_hw_init and
store those in a private data stucture for later use.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36045
Return with the PORT_STATUS register value instead of
writing that directly into the corresponding register.
Also rename the function to ar8327_get_port_init_status.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36043
The presence of the platform data is already verified in
ar8327_hw_init, and the driver does not start without that
anyway.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36042
Setting this bit stops BCM53125 (bgmac actually) from receiving any
packets. This bit is cleared conditionally in b53_switch_reset and it
seems the same is done in bcmrobo.c which never sets that bit again.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 35723
Currently the switch gets registered when an ethernet
driver connects to a PHY of the switch. This method does
not work with the ethernet drivers which are connecting
to the PHY from their ndo_open callback. With those
ethernet drivers, the driver tries to register the switch
each time when the etherned device is opened and this causes
a deadlock.
Move the switch registration into the probe routine to fix
this problem.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35602
The switches are accessed via an MDIO bus. Set the alias
to the name of the MDIO bus, and show that in the message
along with the name of the switch switch device.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35560
The private data of the switch is already
allocated in ar8216_priv, assign that to
each PHY on the same MDIO bus. Also remove
the redundant code from ar8216_config_init.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35559
Sujith says:
This commit breaks the WAN port on my AP96 - DHCP fails.
Reverting it fixes the issue.
commit b67cc3a0cdd02973610d4d5a63226d1c44841e94
Author: juhosg <juhosg@3c298f89-4303-0410-b956-a3cf2f4a3e73>
Date: Fri Feb 8 09:13:18 2013 +0000
generic: ar8216: simplify phy features setup
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@355183c298f89-4303-0410-b956-a3cf2f4a3e73
This change restores the previous behaviour and moves
the code into the ar8216_probe function.
Reported-by: Sujith Manoharan <sujith@msujith.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Tested-by: Sujith Manoharan <sujith@msujith.org>
SVN-Revision: 35549
b53_switch_detect returns value returned by b53_read8, which is 0 for
success. So fail (and return error) only if b53_switch_detect returned
something else than 0. This fixes supported and advertising being zeros
for MDIO access.
Cc: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 35534
It is enough to sleep once after ANEG is enabled on
all PHYs. This reduces boot time on boards with
AR8316 switch.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35532
Use the detach callback to disable packet mangling
to avoid possible NULL pointer dereference.
Compile tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35512
Add swconfig switch driver for Broadcom BCM53XX switch chips. Supports
switches connected through MDIO, SPI or memory mapped registers, and
supports BCM5325, BCM539x, BCM531x5 and the BCM63XX internal switch
chips.
Tested are BCM5325 trough MDIO, BCM53115 through SPI, and BCM6328.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 35305
Only assign a pvid if the current pvid is 0. Fixes using mixed tagged
and untagged traffic on a port and the untagged vlan isn't the last one
of which the port is a member.
Tested on RTL8366S and RTL8367R.
Fixes#8501.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 35227
CC drivers/net/phy/rtl8366rb.o
In file included from drivers/net/phy/rtl8366s.c:16:0:
include/linux/of_platform.h:106:13: warning: 'struct device' declared inside parameter list [enabled by default]
include/linux/of_platform.h:106:13: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
drivers/net/phy/rtl8366s.c: In function 'rtl8366s_probe':
drivers/net/phy/rtl8366s.c:1094:2: warning: label 'err_out' defined but not used [-Wunused-label]
drivers/net/phy/rtl8366s.c:1055:32: warning: unused variable 'pdata'[-Wunused-variable]
CC drivers/net/phy/rtl8366rb.o
In file included from drivers/net/phy/rtl8366rb.c:17:0:
include/linux/of_platform.h:106:13: warning: 'struct device' declared inside parameter list [enabled by default]
include/linux/of_platform.h:106:13: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
drivers/net/phy/rtl8366rb.c: In function 'rtl8366rb_probe':
drivers/net/phy/rtl8366rb.c:1214:2: warning: label 'err_out' defined but not used [-Wunused-label]
drivers/net/phy/rtl8366rb.c:1175:32: warning: unused variable 'pdata'[-Wunused-variable]
CC drivers/net/phy/rtl8367.o
In file included from drivers/net/phy/rtl8367.c:15:0:
include/linux/of_platform.h:106:13: warning: 'struct device' declared inside parameter list [enabled by default]
include/linux/of_platform.h:106:13: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
drivers/net/phy/rtl8367.c: In function 'rtl8367_probe':
drivers/net/phy/rtl8367.c:1712:2: warning: label 'err_out' defined but not used [-Wunused-label]
drivers/net/phy/rtl8367.c:1677:32: warning: unused variable 'pdata' [-Wunused-variable]
CC drivers/net/phy/rtl8367b.o
In file included from drivers/net/phy/rtl8367b.c:15:0:
include/linux/of_platform.h:106:13: warning: 'struct device' declared inside parameter list [enabled by default]
include/linux/of_platform.h:106:13: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
drivers/net/phy/rtl8367b.c: In function 'rtl8367b_probe':
drivers/net/phy/rtl8367b.c:1494:2: warning: label 'err_out' defined but not used [-Wunused-label]
drivers/net/phy/rtl8367b.c:1459:32: warning: unused variable 'pdata' [-Wunused-variable]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34731
fixes the following errors caused by r34682:
CC [M] drivers/net/phy/rtl8366_smi.o
In file included from drivers/net/phy/rtl8366_smi.c:26:0:
drivers/net/phy/rtl8366_smi.h:149:46: warning: 'struct platform_device' declared inside parameter list [enabled by default]
drivers/net/phy/rtl8366_smi.h:149:46: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
drivers/net/phy/rtl8366_smi.c:1398:65: warning: 'struct platform_device' declared inside parameter list [enabled by default]
drivers/net/phy/rtl8366_smi.c: In function 'rtl8366_smi_probe_plat':
drivers/net/phy/rtl8366_smi.c:1400:44: error: dereferencing pointer to incomplete type
drivers/net/phy/rtl8366_smi.c:1402:11: error: dereferencing pointer to incomplete type
drivers/net/phy/rtl8366_smi.c:1403:16: error: dereferencing pointer to incomplete type
drivers/net/phy/rtl8366_smi.c: At top level:
drivers/net/phy/rtl8366_smi.c:1415:46: warning: 'struct platform_device' declared inside parameter list [enabled by default]
drivers/net/phy/rtl8366_smi.c:1415:21: error: conflicting types for 'rtl8366_smi_probe'
drivers/net/phy/rtl8366_smi.h:149:21: note: previous declaration of 'rtl8366_smi_probe' was here
drivers/net/phy/rtl8366_smi.c: In function 'rtl8366_smi_probe':
drivers/net/phy/rtl8366_smi.c:1420:31: error: dereferencing pointer to incomplete type
drivers/net/phy/rtl8366_smi.c:1424:10: error: dereferencing pointer to incomplete type
drivers/net/phy/rtl8366_smi.c:1425:3: warning: passing argument 1 of 'rtl8366_smi_probe_of' from incompatible pointer type [enabled by default]
drivers/net/phy/rtl8366_smi.c:1392:19: note: expected 'struct device_node *' but argument is of type 'struct platform_device *'
drivers/net/phy/rtl8366_smi.c:1427:3: warning: passing argument 1 of 'rtl8366_smi_probe_plat' from incompatible pointer type [enabled by default]
drivers/net/phy/rtl8366_smi.c:1398:5: note: expected 'struct platform_device *' but argument is of type 'struct platform_device *'
drivers/net/phy/rtl8366_smi.c: At top level:
drivers/net/phy/rtl8366_smi.c:1438:1: error: conflicting types for 'rtl8366_smi_probe'
drivers/net/phy/rtl8366_smi.h:149:21: note: previous declaration of 'rtl8366_smi_probe' was here
make[7]: *** [drivers/net/phy/rtl8366_smi.o] Error 1
make[6]: *** [drivers/net/phy] Error 2
make[5]: *** [drivers/net] Error 2
make[4]: *** [drivers] Error 2
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 34703
The ar8216_mib_{capture,flush} functions are similar.
Move the common code into a helper and use that from
the original functions.
This change also fixes a lockdep warning in
ar8216_mib_flush.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34297
swconfig does not compile with 3.7 because
struct netlink_notify->pid has been renamed to
struct netlink_notify->portid
and
struct genl_info->snd_pid has been renamed to
struct genl_info->snd_portid
Use the new names and add compatibility patches
to 3.3 and 3.6.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34288
The names are misleading, those are only valid from
AR8236. The AR8216 chip uses different offsets.
Thanks to Jonas Gorski for the report.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34244
The 'led_brightness_set' function has
been renamed to 'led_set_brightness'
in recent ernels. Use the new name and
add a compatibility patch for 3.3.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 33946
Switch reset on AR8316 appears to clobber the MTU configuration register
and possibly other global config registers. Move global configuration
register init writes back to the reset callback.
SVN-Revision: 30951
After issuing a soft reset on the RT8366{S,RB}
switch, waiting for the last acknowlegement fails
in rtl8366_smi_write_reg. Add a _noack version of
the function and use that for issuing a soft reset.
SVN-Revision: 29844
This patch adds the option to enable jumbo frames on the rtl8366s
switch. This is almost exactly the same as the first patch at
https://dev.openwrt.org/ticket/7977 and it has been requested
in a comment there.
I have tested this and it successfully allows devices on the switch
using jumbo frames to communicate.
Signed-off-by: Ash Hughes <ashley.hughes@blueyonder.co.uk>
SVN-Revision: 28267
Also make switches available under a generic name "switch<num>" for device
name agnostic access. The old device name is used as an alias for backward
compatibility.
SVN-Revision: 27800
This patch adds 802.1Q VLAN support for the ADM6996M chip.
The driver is loaded for both the FC and M model. It will detect which of the
two chips is connected. The FC model is initialised, but no further
functionality is offered.
The PHY driver will always report "100 Mbit/s, link up", for both the M and FC
models. This reflects the fact that the link between switch chip and Ethernet
MAC is always on[1].
Further documentation can be found in the kernel's
Documentation/networking/adm6996.txt
Signed-of-By: Peter Lebbing <peter@digitalbrains.com>
SVN-Revision: 26865
SPIN_LOCK_UNLOCKED has been deprecated since 2.6.19 and will get removed
in 2.6.39, so replace it with DEFINE_SPINLOCK().
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26770
Since the PHY driver is only used for the WAN port and there is virtually
no difference between it and the generic PHY driver, we can sefely remove
it.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26600
Allows to use fids 0 to 7. Default is 0.
Those who will use this don't forget to `set vlan fid` every time
after `set vlan ports` if you want non default behavior.
Minor changes. Version bump.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 24125
The RTL8366S/RB support connecting a second mac to it and using the 5th
port as an independent phy. Therefore we need to handle autonegotiation
changes for phy 4 like on a single phy device.
This fixes#7980, verified on a WNDR3700.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 23127
Tested on ifxmips based board. The PSB6970 is also known as the Infineon Tantos switch.
Signed-off-by: Ithamar R. Adema <ithamar.adema@team-embedded.nl>
SVN-Revision: 22914
