Commit graph

316 commits

Author SHA1 Message Date
Felix Fietkau
eaf8889cf8 ramips: add a script to fix up the broken mac address on the witi board
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48027
2016-01-01 18:57:39 +00:00
John Crispin
4e31b2e869 ramips: add support for Ubiquiti EdgeRouter X (UBNT-ERX)
This router is based on MT7621 SoC, no wifi, no usb, nand.

Works:
* Boots.
* Ethernet.
* Switch.
* Button (reset).
* Flashing OpenWrt from stock firmware.
* Upgrading OpenWrt.

Doesn't work:
* No GPIO leds. All leds are controlled by switch,
  but stock firmware was able to control them.
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
  nand/spi drivers do not support pin sharing,
  so it is not accessable and disabled. Stock
  firmware could read it and it was empty.
* PoE out.

Router has serial pins populated. If looking at the top
of the router, then counting from Eth sockets pins go as:
'GND, RX, TX, GND'. 3.3v, 57600.

U-boot bootloader supports tftpboot, controlled from serial.
This router has two kernel partitions: 'live' and 'backup'.
They are swapped during flashing (on both stock and OpenWrt).
Active partition is controlled by a flag in a factory partition.
U-boot has custom command to switch active kernel partition.
Kernel partitions are 'bare flash' 3MB. Stock bootloader has
no UBI support. Stock rootfs is UBIFS.

Flashing procedure.
Stock firmware uses custom kernel patch to mount squashfs
from a file that is located on UBIFS volume. This makes wiping
out this volume from within stock firmware difficult.
Instead this patch builds image that is flashable by stock firmware
and contains initrams image (with minimal set of packages
to fit into kernel partition). Once this is flashed one can reboot
into initramfs OpenWrt and use sysupgrade to flash OpenWrt including
rootfs into nand.
Note: factory image is only built if initramfs image is enabled.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47881
2015-12-12 07:38:06 +00:00
Jo-Philipp Wich
67e1c87012 all: drop old uci-defaults.sh
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47867
2015-12-11 15:26:06 +00:00
John Crispin
9f14006809 ramips: add additional support for MQmaker WiTi board
The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram,
2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and
one 5 ghz antenna.

This is the 6th submission that adds support for XHCI in the device tree
file, along with switching the location of the 2 radio's and addition of
the kmod-i2c-mt7621 in the default packages of the profile.

Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>

SVN-Revision: 47845
2015-12-11 15:04:13 +00:00
John Crispin
6cbb1be464 ramips: Fix support for PBR-M1 board
The PBR-M1 support in current OpenWrt is for the early demo board and it doesn't work on the final board.This patch fixes the support for it.

The LED called pbr-m1:buzzer is a beeper connected to GPIO26 so I used gpio-beeper instead of gpio-leds.

Signed-off-by: 郭传鈜 <gch981213@gmail.com>

SVN-Revision: 47844
2015-12-11 15:03:50 +00:00
Jo-Philipp Wich
527ec2af59 all: remove dummy ucidef_set_interface_loopback() from board.d
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47744
2015-12-03 23:13:00 +00:00
Jo-Philipp Wich
8f8b702f85 board.d: remove redundant ucidef_set_interfaces_lan_wan() calls
This removes calls to ucidef_set_interfaces_lan_wan() and
ucidef_set_interfaces_lan() on boards where all relevant info can be
inferred from the switch definition.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47722
2015-12-03 17:30:56 +00:00
Jo-Philipp Wich
9b02e73188 board.d: merge ucidef_add_switch() and ucidef_add_switch_ports()
This changes uci-defaults-new.sh, config_generate and all relevant board.d
files in order combine ucidef_add_switch() and ucidef_add_switch_ports() into
a single function.

Also removes now superfluous enable and reset arguments.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47721
2015-12-03 17:30:24 +00:00
Jo-Philipp Wich
d17a64c7c0 base-files: uci-defaults-new: remove reset/enable args of ucidef_add_switch()
Out of 69 switch definitions, only 3 pass something different than "1" as
values for reset and enable, with one of those three being invalid.

This change ...

 * removes the reset and enable arguments from ucidef_add_switch()
 * unconditionally writes reset:1 and enable:1 to JSON
 * converts the three users of nonstandard values to ucidef_add_switch_attr()

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47720
2015-12-03 17:30:08 +00:00
Jo-Philipp Wich
de51026515 ramips: switch ucidef_add_switch_vlan() to ucidef_add_switch_ports()
This migrates the final board.d user of ucidef_add_switch_vlan() to the new
ucidef_add_switch_ports() approach, fixing some logic errors for a few boards
along the way.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47717
2015-12-03 15:46:29 +00:00
Jo-Philipp Wich
ecf5b4fab7 ramips: hg255d: replace ucidef_set_led_interface() with ucidef_set_led_netdev()
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47657
2015-11-26 12:46:04 +00:00
John Crispin
8c1f5141ce ralink: add support for netis WF-2881
netis WF-2881 is an MT7621AT based router with MT7602EN, MT7612EN.
It has 128MB DDR3, 128MB SLC NAND FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.

this device only works on top of UBI.

Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons (reset button)
* ethernet switch and USB diag LEDs
* UART
* GPIOs
* sysupgrade

Tested and not working
* failsafe

Signed-off-by: YounJae Rho <luxflow@live.com>

SVN-Revision: 47619
2015-11-24 18:29:26 +00:00
John Crispin
e9baf8265b ramips: add support for Youku YK1
Changes since V1:
I resend this patch for current trunk.The former V1 patch is for CC branch.

Signed-off-by: Shonn Lu <countrysideboy@qq.com>

SVN-Revision: 47617
2015-11-24 18:29:02 +00:00
John Crispin
dc699dd547 ramips: minor tweak to the lks7688 baord name
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47388
2015-11-05 10:01:23 +00:00
John Crispin
2350c149b5 ramips: add feature to blink led on sysupgrade
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47373
2015-11-03 13:32:02 +00:00
John Crispin
165244a222 ramips: add support for ZBT WG2626
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 47351
2015-11-02 10:18:19 +00:00
John Crispin
907c67fa87 ramips: preinit: use iproute2 instead of vconfig
Replace use of vconfig with the corresponding iproute2 syntax in
/lib/preinit/07_set_preinit_iface_ramips

The switch reset work-around needed on some ramips targets used the
deprecated vconfig tool to bring up the pre-init/failsafe interface.
This doesn't work on recent builds where vconfig is no longer being
deployed, resulting in the device being unreachable when triggered
into failsafe mode.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 47349
2015-11-02 10:18:02 +00:00
John Crispin
3760b95702 ramips: add support for Dovado tiny AC
Add support for Dovado tiny AC wifi router.

Soc: mt7620a
ram: 64MB
flash: 8MB
1x usb 2.0
two gigabit lan ports

5ghz wlan is not supported on this board since there is no gpl driverfor mt7610e wifi chip.

Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>

SVN-Revision: 47348
2015-11-02 10:17:51 +00:00
John Crispin
83693c911a ramips: add function to change rt2x00 wifi eeprom mac
Some boards like dovado tiny ac have generic ralink mac in onflash wifi eeprom.
Add eeprom_set_macaddr function to rt2x00 eeprom extract script which changes mac addr insde eeprom dump.

Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>

SVN-Revision: 47347
2015-11-02 10:17:41 +00:00
John Crispin
8fa6927415 ramips: add support for the Asus RP-N53 in the "02_network" boot script
This patch adds a case for the Asus RP-N53 in the "02_network" boot script. Without this, the lan interface does not get configured on startup, effectively bricking the device.

Signed-off-by:  Alberto Mattea <alberto@mattea.info>

SVN-Revision: 47345
2015-11-02 10:17:26 +00:00
John Crispin
51dd991d39 ramips: add LinkIt Smart7688 support
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47203
2015-10-19 10:07:38 +00:00
John Crispin
c10bdf11ff ramips: Add base-files for HiWiFi HC5x61 models
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.

The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.

v3 fix
   1: Fixed model order
   2: Remove manufacturer name from model name
   3: Use a hacky but prettier way to get mac address.

Signed-off-by: Xiaoning Kang <kangxn@163.com>

SVN-Revision: 47111
2015-10-05 10:25:47 +00:00
John Crispin
86a1e46b63 ramips: add proper mt7688 detection
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46957
2015-09-16 08:31:00 +00:00
John Crispin
57c5910535 ramips: Added WIZnet WizFi630A Platform based on Ralink RT5350
This patch is to add the WIZnet WizFi630A board as a new platform. The board is in mini pci express form factor.

Signed-off-by: Tobias Welz <tw@wiznet.eu>

SVN-Revision: 46921
2015-09-14 20:09:31 +00:00
John Crispin
2efdc7c896 ramips: add support for Planex DB-WRT01
This patch add support for Planex DB-WRT01. DANBOARD route on
 the MT7620A SoC with two Ethernet port and a 802.11n 2.4 GHz radio.
 DANBOARD is Cartoon character.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 46918
2015-09-14 20:08:55 +00:00
John Crispin
0f155a330e ramips: base-files: optimize etc/diag.sh and etc/board.d/01_leds scripts
Instead of using board name provided explicitly as text in LED name, ex.:

[...]
mlwg2)
	status_led="mlwg2:blue:system"
[...]

use $board variable, which allows to combine together multiple boards with same color and LED names, ex:

[...]
mlw221|\
mlwg2)
	status_led="$board:blue:system"
[...]

The above approach allows to shrink size of code in base-files/etc/board.d/01_leds and base-files/etc/diag.sh scripts dramatically.
One thing to keep in mind here is that we assume to use proper and consistent LED naming scheme ("device:color:led-name").

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46665
2015-08-17 06:24:47 +00:00
John Crispin
1a392636a5 ramips: use consistent naming scheme for LEDs
The upstream LED naming convention is "device:color:led-name", but it seems that many of supported boards in OpenWrt don't follow this approach.
The following patch fixes this inconsistency in dts{,i} files and updates base-files scripts for ramips target:
 * fixes wrong indentation
 * keeps case statements structure in same convention as in other scripts (no empty line after ";;", no indentation for case...esac body)
 * fixes wrong LED names for some of boards (makes them the same as in dts{,i} files)
 * combines boards with same configuration (ex. set_wifi_led "rt2800pci-phy0::radio" in 01_leds)

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46664
2015-08-17 06:24:34 +00:00
John Crispin
eba4a143c6 ramips: reorder the sysupgrade script
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46660
2015-08-17 06:18:38 +00:00
John Crispin
f32116987f ramips: remove unnecessary LED declaration for WT1520 in diag.sh
This device doesn't have defined LEDs in its dts file.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46635
2015-08-17 06:03:42 +00:00
John Crispin
2f0449419f ramips: fix indentation, case statements structure and optimize base-files/etc/board.d/02_network
The following patch:
 * fixes wrong indentation
 * combines together boards with same configuration
 * removes unnecessary spaces
 * removes empty lines after ";;" and uses only "|\" (for consistency)
 * orders boards alphabetically

in base-files/etc/board.d/02_network script.

One bug was left untouched: freestation5 board is listed twice in case statement, in ramips_setup_macs().

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46634
2015-08-17 06:02:59 +00:00
John Crispin
4069a8e49c ramips: be consistent with case statement in base-files/lib/upgrade/platform.sh
Always use "|\" (without spaces) and keep boards in alphabetical order.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46633
2015-08-17 06:01:49 +00:00
John Crispin
a18b35a2f1 ramips: remove leading spaces, sort boards and optimize base-files/lib/ramips.sh
This patch:
 * fixes various mistakes (leading spaces, wrong or missing model names)
 * shortens model strings (we don't need to use whole model string from dts file, make it for consistency and as optimization)
 * sorts boards alphabetically

in base-files/lib/ramips.sh script.

Case statement was tested after above changes with simple script, which:
 * takes model string from dts{,i} file (model = "...")
 * provides this value as case input ($machine)
 * returns output ($name)

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46632
2015-08-17 06:01:44 +00:00
John Crispin
0d464c360f ramips: remove old code for Edimax BR-6524N
It seems that support for Edimax BR-6524N was dropped long time ago (dts file for this device is missing).
This patch removes remaining code.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46630
2015-08-17 06:01:23 +00:00
John Crispin
2fe5cf2bd6 ramips: fix 7Links PX-4885 dts{, i}, board, image and profile names
The following patch changes 7Links PX-4885 dts{,i} filenames, board, image and profile names from "PX4885" to "PX-4885" (for consistency).

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46629
2015-08-17 06:01:06 +00:00
John Crispin
e4b6dcee5e ramips: fix Buffalo WMR-300 dts, board, image and profile names
The following patch changes Buffalo WMR-300 dts filename, board, image and profile names from "WMR300" to "WMR-300" (for consistency).

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46628
2015-08-17 06:00:49 +00:00
John Crispin
713c81e97b ramips: fix Omnima models, images and profiles names
Official names for supported Omnima products are (as on website):
 * Omnima HPM
 * Omnima MiniEMBWiFi
 * Omnima MiniEMBPlug

This patch changes:
 * board names
 * dts filenames
 * profile names
 * image filenames
 * LED names

for Omnima devices, for consistency.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46627
2015-08-17 06:00:11 +00:00
John Crispin
0bb270429d ramips: fix Edimax BR-6425 board name
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46626
2015-08-17 05:59:57 +00:00
John Crispin
633c46a1d4 ramips: fix Olimex models, images and profiles names
Official names for RT5350F based OLinuXino products are "RT5350F-OLinuXino{,-EVB}" as on official manufacturer website.
The following patch:
 * changes board names from "olinuxino-rt5350f{,-evb}" to "rt5350f-olinuxino{,-evb}"
 * changes filenames of dts and profile files
 * changes image filenames

for Olimex RT5350F-OLinuXino{,-EVB} devices.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46623
2015-08-17 05:59:29 +00:00
John Crispin
66f6c9e231 ramips: fix Sitecom WL-341v3 board and image names
The following patch changes:
 * board name from "wl341v3" to "wl-341v3"
 * dts filename
 * LED names in dts file

for Sitecom WL-341v3 device.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46622
2015-08-17 05:59:12 +00:00
John Crispin
102073ca17 ramips: fix Argus ATP-52B board and image names
The following patch:
 * changes board name from "argus-atp52b" to "atp-52b"
 * changes dts filename
 * fixes LED names in dts file and base-files scripts
 * removes manufacturer name from image filename

for Argus ATP-52B device.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46621
2015-08-17 05:58:57 +00:00
John Crispin
7bf1db0dcb ramips: fix UPVEL model names
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46618
2015-08-17 05:58:20 +00:00
John Crispin
a0b8c60134 ramips: fix Xiaomi MiWiFi Mini board, image and profile names
The following patch:
 * changes board name from "xiaomi-miwifi-mini" to "miwifi-mini"
 * changes filenames of dts and profile
 * fixes LED names in dts file and base-files scripts
 * removes manufacturer name from image filename

for Xiaomi MiWiFi Mini device.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46617
2015-08-17 05:58:15 +00:00
John Crispin
f38db77707 ramips: fix Zbtlink ZBT-WR8305RT board name
There is another Zbtlink board (ZBT-WA05) supported in ramips target, so use the same naming scheme for ZBT-WR8305RT board and its dts file.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46614
2015-08-17 05:57:41 +00:00
John Crispin
e04e44a223 ramips: add subtarget for mt7688
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46473
2015-07-24 09:11:56 +00:00
John Crispin
dcae3723fd ramips: add support for STORYLiNK SAP-G3200U3
STORYLiNK SAP-G3200U3 is an AC1200 router based on MT7621AT+MT7602EN+MT7612EN.
It has 128MB DDR3, 8MB NOR FLASH, 5-port Gbps switch and 1x USB 3.0.

The following patch adds support for this device.

Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons
* ethernet switch and USB diag LEDs
* UART
* GPIOs

Tested and not working:
* LEDs for WiFi radios (connected with WiFi chips, not supported in mt76?)
* failsafe mode (known problem, needs workaround like other MTK based devices)

More information in Wiki: http://wiki.openwrt.org/toh/storylink/sap-g3200u3

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46454
2015-07-24 09:09:22 +00:00
John Crispin
eff79253f2 ramips: add support for Planex MZK-DP150N
This patch add support for Planex MZK-DP150N.
a mini router on the MT7620A SoC with one Ethernet port and a 802.11n 2.4 GHz radio.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 46405
2015-07-17 12:51:08 +00:00
John Crispin
b618573815 ramips: adding support for OY-0001 Wireless Router
Adding support for OY-0001 Wireless Router.
OY-0001 is a wireless router made by oyewifi.com. Below is the details:
MT7620A, 128MB DDR2, 16MB FLASH, SD Slot, USB 2.0, 4 x LAN + 1 x WAN.

Signed-off-by: Tom Deng <2579131212@qq.com>

SVN-Revision: 46349
2015-07-14 07:40:22 +00:00
John Crispin
2658b33f68 ramips: a5-v11 board fix power led blinking at boot
Signed-off-by: Konrad Kotowicz <skoti1@go2.pl>

SVN-Revision: 46215
2015-07-07 13:43:37 +00:00
John Crispin
cf1fb25e67 ramips: Add Support for the Linksys RE6500
This patch adds support for the Linksys RE6500 Range Extender

http://wiki.openwrt.org/toh/linksys/re6500

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 46043
2015-06-18 18:20:56 +00:00
John Crispin
e26ba31f76 ramips: Add support for the D-Link DCS-930 B1
http://wiki.openwrt.org/toh/d-link/dcs-930l

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 46042
2015-06-18 18:20:46 +00:00