The D-Link DIR-869 A1 doesn't accept images with the jffs2 marker added
after the checksummed range, so we need to include it in the checksum and
fix it on first boot.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Split seama-factory and seama-sysupgrade into smaller pieces (similar to
the ramips code) to make the image generation more flexible.
Also use standard pad-offset instead of adding a block of zeros at the
beginning of the image that is later cut off again. Standard pad-rootfs can
be used as the seal header doesn't contain an image size or checksum.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
In case the adsl/vdsl service is disabled intentional, the output is
cluttered with the following message multiple times if the status of
the dsl line is queried:
killall: vdsl_cpe_control: no process killed
If the dsl line status is queried by LuCI, the logfile is spammed with
the message.
Fix the issue by using killall in quite mode. In quite mode killall
still returns a non-zero value if the to be killed process can not be
found so that existing logic based on the return value still works.
Signed-off-by: Mathias Kresin <dev@kresin.me>
TP-Link uses a different region coding mechanism for IL firmware for the Archer
C7 v2. Instead of of setting the region, they set a different TPLINK_HWREV.
Signed-off-by: Amir Rachum <amir@rachum.com>
Due to the introduced double whitespace the default package selection
isn't applied. This leads to errors like a not working networking
because of a missing swconfig binary.
Fixes FS#208.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add USB led aliases to boards having an led which is meant to be used
as USB led according to the manuals.
Remove the kmod-ledtrig-usbdev from the default package selection for
boards not having an USB led. Add the kmod-ledtrig-usbdev to boards
where it is missing.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use a more generic name for the lantiq_get_dt_led_chosen function.
Drop the lantiq_is_dt_led_chosen function. The lantiq_get_dt_led
function can be used to achieve the same.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Convert the Zynq target to use the new image build code in order to fix
broken image generation after 9945a1dca5
changed the handling of CPIO images.
Also remove the misapplied ubifs feature flag since the image generation is
not using UBIFS for building FIT images.
As part of the conversion, move the DTB building and the uImage ramdisk
generation into separate build steps which can be generalized and shared
with other targets, like APM821xx, in the long run.
Also remove the legacy profile declarations and use new-style per-device
profiles which will allow different package sets per image in the future.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add some missing symbols to the generic 4.1 kernel config which got triggered
by the introduction of the hda-intel sound module.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
applied bb-final-ramips-add-zyxel-nbg-419n2.patch from
123serge123, found at https://yadi.sk/d/1ZV0lKJwbTE65;
see https://forum.openwrt.org/viewtopic.php?pid=246905#p246905,
modified slightly to fit to CC release and to new lede build
system: image/rt305x.mk include file is used now
changed NBG-419N2.dts format to fit style of other dts files
Signed-off-by: Klaus <k-laus@quantentunnel.de>
This includes:
- use of local 'board' variable in LED names, wherever possible
- merge of boards with exactly the same LED configuration
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Keep everything in alphabetical order. Boards are ordered in two steps,
first within/inside common configuration (case section), then sections,
globally.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This includes:
- code style fixes
- removal of huge comment (it should be in doc, not here) and some small ones
- removal of redundant config for DR531/WPJ531 as the default is the same
- merge of boards with exactly the same interfaces config
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Convert etc/board.d/02_network in ar71xx target to the same shape
as we have in ramips target. Split code into two new functions:
- interface/s setup in ar71xx_setup_interfaces()
- MAC/s setup in ar71xx_setup_macs()
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
sysupgrade command fails due to missing U-Boot environment-processing binaries on sysupgrade ramdisk. The missing binaries result in the following output:
Switching to ramdisk...
Performing system upgrade...
ash: /usr/sbin/fw_printenv: not found
ash: fw_setenv: not found
ash: touch: not found
cannot find target partition
Fixes FS#197.
Signed-off-by: Aaron Curley <accwebs@gmail.com>
- CPU: MT7620A 580MHz
- Flash: 8MB - RAM: 64MB
- External PA+LNA on both WLAN2.4 and WLAN5
- 4x LAN ethernet and 1x WAN ethernet
Signed-off-by: Xuefu Lin <xuefulin@gmail.com>
It missed some changes needed for kernel 4.4. This is only used by the
Falcon SoC and not for the xRX SoCs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The main difference is it supports DT binding. This allows us to use DT
for specifying controller and the new standalone USB 3.0 PHY driver.
Thanks to that we don't need out of tree patch adding PHY initialization
to the controller driver anymore.
This problem has been fixed by upstream commit 757de492f2d ("xhci: fix
platform quirks overwrite regression in 4.7-rc1").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This drops built-in support for USB 2.0 PHY and starts using separated
driver that was upstreamed & backported some time ago.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The nf_reject_* and nf_nat_masquerade_* modules are moved into the
corresponding kmod-nf- packages. Appropriate dependencies are added to the
kmod-nft- packages.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Refresh patches for all targets that support kernel 4.4.
compile/run-tested on brcm2708/bcm2710 only.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Forgot to update kernel-version.mk, so updated patch. Compile-tested on x86/64 and ar71xx; run-tested on x86/64 and ar71xx.
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
-add spi pins
-move mdio and rgmii pinctrl from gmac and mdio into pinmux node
-add i2c4 pinctrl into rpm node
-add pin details into several nodes
-update gmac1 and gmac2 parameters
-update mdio phy0 and phy4 registers by ddwrt devs findings
-fix i2c4 pin drive-strengh
-remove pcie pins as it's already present in ipq8065 DT
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
With symlink tree some directories are just symlinked which
means IB and SDK end up with a symlink instead of an actual
directory; this fixes the missing files by dereferencesing
the directories instead of copying the symlinks.
Signed-off-by: Daniel Dickinson <lede@cshore.thecshore.com>
Now that the firmware for BCM43430 has been submitted to linux-firmware use it
and remove RPiDistro package.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add patches for SFP support and package it for ClearFog. Tested with a
Juniper SFP module.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
