The MikroTik hEX v3 (RB750Gr3) is a MT7621AT board which is similar to most MT7621 reference designs, it can be easily supported by this patch; however, the stock RouterBOOT bootloader has to be replaced by a MT7621 SDK U-Boot such as https://github.com/ndoo/RB750Gr3-U-Boot - U-Boot configured for the RB750Gr3 (16MiB SPI flash, 256MiB DDR3 RAM at 1200MHz).
RouterBOOT, the stock bootloader, does not initialize the UART and boots silently, making it preferable to replace it with a MT7621 SDK U-Boot with UART (57600 8N1) that supports HTTP, TFTP or serial upload of sysupgrade firmware and U-Boot.
Furthermore, RouterOS, the stock firmware, is contained in a proprietary modification of SquashFS without GPL sources; UART is also disabled in stock firmware.
The combination of LEDE firmware generated by this PR and MT7621 SDK U-Boot expects the printed MAC address to reside at offset `0xe000` of the factory partition (absolute offset is `0x4e000`); this is similar to the factory MAC address offset for several other MT7621 devices.
A 16MiB flash dump suitable for use with flashrom will be provided if/once this patch is accepted and binaries are built by LEDE buildbot. Alternatively, writing the U-Boot to the SPI flash starting at 0x0 offset and booting the board with serial console attached will allow TFTP, HTTP or serial upload of sysupgrade firmware.
Signed-off-by: Andrew Yong <me@ndoo.sg>
- setting read-only flag to important partitions
- enabling PA to improve 2.4 GHz signal strength
- add missing leds
- rename colour led
- add mac adress to 5GHz wlan interface
- included <dt-bindings/input/input.h> and <dt-bindings/gpio/gpio.h>
Signed-off-by: Henryk Heisig hyniu@o2.pl
All of the touched boards don't have an ethernet port. Allow to use the
wps button on these boards to enable the wireless radio after boot.
The force enabled wireless for the DCH-M225 is removed. It is reckless
to bring up an unencrypted wireless network by default these days.
Using the wps button to bring up the radio seam to me the better
approach.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Assign the reset functionality to the wps/reset buttons. Use the wlan
switch of the 6200n to enable/disable wlan.
Add the internet led of the 6200nl and use the led for boot status
indication
Signed-off-by: Mathias Kresin <dev@kresin.me>
With 3a9752bbd2 and later changes to
ramips_set_preinit_iface() the default vlan config applied during
preinit was changed. These changes were made without updating the
default network config to ensure that vlan interfaces used for lan/wan
are still configured.
Fix the issue by using the default all LAN portmap and disabling not
connected switch ports using portdisable device tree parameter.
Signed-off-by: Mathias Kresin <dev@kresin.me>
applied bb-final-ramips-add-zyxel-nbg-419n2.patch from
123serge123, found at https://yadi.sk/d/1ZV0lKJwbTE65;
see https://forum.openwrt.org/viewtopic.php?pid=246905#p246905,
modified slightly to fit to CC release and to new lede build
system: image/rt305x.mk include file is used now
changed NBG-419N2.dts format to fit style of other dts files
Signed-off-by: Klaus <k-laus@quantentunnel.de>
- CPU: MT7620A 580MHz
- Flash: 8MB - RAM: 64MB
- External PA+LNA on both WLAN2.4 and WLAN5
- 4x LAN ethernet and 1x WAN ethernet
Signed-off-by: Xuefu Lin <xuefulin@gmail.com>
Due to the missing phy-mode setting, the switch wasn't initialised.
The wireless requires an eeprom to work. Use the same mac addresses as
the stock firmware.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The AR8327 initvals were not copied to the DTS during the switch from
mach file to device tree and broke the switch on the device.
The former used PORT6 related initvals were wrong and have been
corrected.
The phy mode setting for the switch was missing in the DTS as well.
The wireless requires an eeprom to work. The dual band wireless chips
have both bands enabled by default but only one band per chip is
working.
The stock firmware uses the following mac addresses:
LAN: AA:BB:CC:DD:EE:E4
WAN: AA:BB:CC:DD:EE:E4
2.4GHz: AA:BB:CC:DD:EE:E4
5 GHz: AA:BB:CC:DD:EE:E8
Assuming the mac address range :E4 to :E8 is reserved for this device,
the MAC addresses were reorder to have a unique MAC address for each
interface:
LAN: AA:BB:CC:DD:EE:E4
2.4GHz: AA:BB:CC:DD:EE:E4
WAN: AA:BB:CC:DD:EE:E5
5 GHz: AA:BB:CC:DD:EE:E8
Signed-off-by: Mathias Kresin <dev@kresin.me>
Fixes the following compiler warning:
Warning (reg_format): "reg" property in /ethernet@10100000/port@0 has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /ethernet@10100000/port@0
Warning (avoid_default_addr_size): Relying on default #size-cells value for /ethernet@10100000/port@0
Signed-off-by: Mathias Kresin <dev@kresin.me>
Thunder Timecloud is a small NAS with MT7621A. It has 1 USB port and an
SD Card slot. There is no wireless cards.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
D-Link DCH-M225 is based on Mediatek MT7620 with 64MB ram, 8MB flash,
3.5mm audio out support. but no ethernet and usb ports.
so you must default enable wifi.
Signed-off-by: Michael Lee <igvtee@gmail.com>
The NixCore X1 is a Ralink/MediaTek rt5350 WiFi Module.
http://nixcores.com/
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: Drew Gaylo <drew@nixcores.com>
The partition size is wrong, leading to out-of-disk-space even on no/moderate use.
Upstream fix from vendor: 2f25eb57ed
Suggested fix for openwrt: https://dev.openwrt.org/ticket/20321
Signed-off-by: Rene Treffer <treffer@measite.de>
Pinmux for rgmii needs to be set to rgmii, not gpio.
Hide the ESW switch on boot (using new rgmii esw devicetree attribute).
Also add a Sitecom-specific profile, since the image needs to include
the rtl8366 kernel driver.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
The ZBT APE522II is a dual-radio outdoor CPE based on the MT7620a SoC. It has
64 MB RAM, 8 MB flash, 2 Fast Ethernet ports via internal switch (one with
802.3af 48V PoE support), a 802.11b/g/n SoC 2.4 GHz radio and an 802.11a/n/ac
MT7612E-based 5 GHz radio.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
DuZun DM06 is a develop board based on mt7628
64M RAM, 8M SPI Flash, 1 WAN, 1 LAN.
wm8960 codec with line out, line in and speaker output.
Signed-off-by: Michael Lee <igvtee@gmail.com>
The Widora board is similar to the Linkit 7688 but features a larger flash
capacity.
Signed-off-by: Yuan Chenmang <771992497@qq.com>
[Jo-Philipp Wich: Reword commit message, cleanup initial PR]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Currently, for RT5350 and MT7628, esw is marked as compatible with
"ralink,rt3050-esw". While this is true, the switches within RT5350
and MT7628 actually support more functionality than the RT3050 switch.
One such example is per-VLAN untagging, which is an important feature.
RT3352 is another example of this, but it already has an additional
compatible property, which allows to differentiate it from RT3050.
This commit adds such more specific properties for RT5350 and MT7628
as well.
Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
- disable all ethernet ports except port 0 on MPR-A2
Port 0 is the only ethernet port on this router, so disable all other PHYs in order to save power.
- don't use a VLAN for the single ethernet port of the MPR-A2
Like A5-V11, this router only has one ethernet port.
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
This commit makes the following modifications to ramips dts files:
1. Add clkctrl node to all dtsi files (although not used for now)
2. Add clocks and clock-names properties to some nodes (usbphy, pci)
3. Add usbphy node for rt3050 (although not used for now)
4. Add clock-frequency to uart nodes in mt7621.dtsi and mt7628an.dtsi
These modifications, although not fully used at the moment, will make
it easier for FreeBSD to adopt and use LEDE ramips dts files with
minimal changes for easier maintenance.
Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
Add node aliases to dtsi files.
Reword dts files so they're more in-line with upstream.
Fix some more warnings and errors reported by dtc
Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
