Rather than including all machines for the generic subtarget in the base
configuration, leave the base configuration without specific machines and
create a proper subtarget config for ar71xx/generic. The configuration
diffs of the mikrotik and nand subtargets get significantly shorter, as
will the configurations of future subtargets.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
While we'd like to convert ar71xx to DT-based configuration
eventually, we aren't quite there yet, and shipping half-baked DT support
that is not used at all wastes precious space.
Saves ~120KB before LZMA, ~33KB after LZMA.
Run-tested on TP-Link CPE510 and TL-WR841 v7.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Backport patches that separate spectral scan support from general debugfs
support of ath9k/ath10k; this allows to remove the dependency on
KERNEL_RELAY from these driver packages even with debugfs enabled and
avoids the memory footprint of the relay buffers allocated by ath9k/ath10k
even when they aren't used at all.
The KERNEL_RELAY dependency is moved to a new config symbol that enables
spectral scan support in these drivers.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Eventually the BUILDONLY package flag could be replaced by simply creating
a package Makefile without any BuildPackage calls. This will fail for now,
as BuildPackage also causes the Makefile's compile target etc. to do
something useful at all.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Package "features" seem to be unused for some time. In any case, custom
Config.in snippets and package PROVIDES are a much more flexible way to
express similar options.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Properly resolve build depends to source packages and runtime depends to
binary packages. Dependencies on virtual packages are resolved to the first
provider now.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Instead of adding virtual packages to the normal package list, keep a
separate list for provides, make each package provide itself, and resolve
all dependencies through this list. This allows to use PROVIDES to replace
existing packages.
Fixes FS#837.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Runtime depends cannot have a buildtype suffix, and they never refer to
source package names. In addition, this adds warnings about unsatisfiable
dependencies.
Furthermore, this change fixes the generation of conditional build
dependencies for virtual packages provided by different source packages.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Target build depends are similar to host build depends in that they refer
to source packages rather than binary packages. Therefore, it makes sense
to handle them together, rather than putting them in a list together with
runtime depends and trying to figure out if the entries refer to source or
to binary packages afterwards.
This does lead to PKG_BUILD_DEPENDS entries referring to binary package
names not working anymore, which requires some fixes in the package
repositories.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This feature has been unused for years, and its scope is too limited to be
actually useful.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Every single reference to subdir was concatenated with the source package
name, so it makes sense to store the concatenated value instead.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
We often want to access fields of a source packages through pkg->{src}.
Allow accessing them directly instead of resolving the source hash through
srcpackages.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
All build dependencies are between source packages. Interating over source
rather than binary packages simplifies parts of the code and prepares
further improvement.
As a side effect, this changes the implicit default variant of a few
packages (the first defined is used now instead of the lexicographically
first).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Build types are a property of source rather than binary packages. This is a
preparation for followup cleanup.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Turn the srcpackage values into hashes to allow storing more information
than just binary package names.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Nothing explicitly depends on base-files, and even if it would, it would
not cause any problems. Remove the unused special case.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
18090d9 overlay: fix compilation with glibc
2a9a6ea libfstools: optimize building directory string for glob
de6b026 libfstools: support file paths longer than 255 chars
Signed-off-by: John Crispin <john@phrozen.org>
Symbol CONFIG_INITRAMFS_FORCE allows to ignore the value passed by the
bootloader.
By default, all symbols containing INITRAMFS are wiped from the final
config and then re-added conditionally.
Add support for this symbol, as the build will stop otherwise
questioning the user about this option:
* Restart config...
*
*
* General setup
*
Cross-compiler tool prefix (CROSS_COMPILE) []
Compile also drivers which will not load (COMPILE_TEST) [N/y/?] n
...
Initial RAM filesystem and RAM disk (initramfs/initrd) support
(BLK_DEV_INITRD) [Y/n/?] y
Initramfs source file(s) (INITRAMFS_SOURCE) []
Ignore the initramfs passed by the bootloader (INITRAMFS_FORCE)
[N/y/?] (NEW)
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Disable CONFIG_PROC_PAGE_MONITOR in most places and only keep it enabled
for virtual targets such as malta or potent ones like x86.
This saves up to 4KB of uncompressed kernel size and significantly
decreases CPU load under certain workloads.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* QCA IPQ401x
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=OM-A42
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=OM-A42
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
* powered only via POE
- 802.3af POE on Ethernet 1
- 18-24v passive POE (mode B) on Ethernet 2
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
The kernel driver gpio-wdt or the userspace tool om-watchdog can be used to
trigger external gpio watchdog chips. The gpio-wdt driver has the benefit
that it can be configured together with the rest of the device in the DTS
and better integrates in the OpenWrt via procd.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Combined Extended Images V1 can be created easily via the new image
commands using
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | combined-ext-image
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
The new build commands operate on the input image and use it again as
output image. This conflicts with the way combined-ext-image.sh was
operating. It required that input and output files are different files and
and that it can write freely to the output file.
This can be avoided when all intermediate build steps by
combined-ext-image.sh are done in a temporary directory. The output file is
then only overwritten in the last step.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Board Data File (BDF) is loaded upon driver boot-up procedure. The right
board data file is identified on QCA4019 using bus, bmi-chip-id and
bmi-board-id.
The problem, however, can occur when the (default) board data file cannot
fulfill the vendor requirements and it is necessary to use a different
board data file.
This problem was solved for SMBIOS by adding a special SMBIOS type 0xF8.
Something similar has to be provided for systems without SMBIOS but with
device trees. No solution was specified by QCA and therefore a new one has
to be found for ath10k.
The device tree requires addition strings to define the variant name
wifi@a000000 {
status = "okay";
qcom,ath10k-calibration-variant = "RT-AC58U";
};
wifi@a800000 {
status = "okay";
qcom,ath10k-calibration-variant = "RT-AC58U";
};
This would create the boarddata identifiers for the board-2.bin search
* bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=RT-AC58U
* bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=RT-AC58U
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Use the generic board detection method:
- Board name: First compatible string from the device tree
- Board model: Model property from the device tree
Change occurrences of board name in userspace by the compatible
string, and removed target specific board detection script
Replace the definition of SUPPORTED_DEVICES in Device/Default
to extract the dt compatible string from each device definition.
Additionally, for devices supported by lede-17.01, append
the value of BOARD_NAME to SUPPORTED_DEVICES in the device
definition.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Use <manufacturer>_<modelname> as image name for board using the
devicetree compat string as boardname.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
This will allow to maintain the current syntax for LEDs config
when switching to a device tree compatible string boardname.
None of the current boards use a comma in the boardname, so they
will be unaffected.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
There are only artifacts for these boards in our tree and not even
partial support.
Drop teh stale files.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The 4.14 kernel configuration defaulted to a v4/v5 multiplatform while
4.9 was using a v6/v7 default configuration. Resync 4.14 against 4.9 so
they are nearly identical.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add a bunch of missing configuration symbols found while building
armvirt for 4.14 after re-synchronization of the configuration between
4.9 and 4.14.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Commit 30f61a34b4 claimed to drop -d & -p
options. In reality only -d was dropped. Update command help text to
reflect that -d is no longer a supported option.
Fixes FS#1187
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This patch updates the apm821xx target to use the 4.14 kernel.
4.14 finally ships with a driver for the WNDR4700's tc654 fan
controller. The custom driver is deprecated in favor of the
upstream driver and the thermal cooling definitions in the DTS
are updated.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
More important bug fix:
402f05c Use full-rate mtu_time in all tins. Fixes an issue where some
cake tins experienced excessive latency since 49776da (dynamically
adjust target)
Minor bug fixes:
31277c2 Avoid unsigned comparison against zero. Fix compiler warning,
no known impact.
8cf5278 ack_filter: fix TCP flag check. A very contrived case may have
lead to dropping a SYN packet that should not be dropped.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Without this patch one sdcard image with the following name is created
for all devices:
openwrt-at91-sama5--sdcard.img.gz
This makes the build system create device specific versions like:
openwrt-at91-sama5-at91-sama5d2_xplained-sdcard.img.gz
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
